CTScottOriginal postUSA, CT · Jan 30, 2010#1There are many threads regarding DIY cruise control. The purpose of this one is to centralize all of the information.
By DIY Cruise Control, I am referring to using the functionality built into the US and Canadian Yaris' ECM, as opposed to installing a 3rd party cruise control system. All US and Canadian Yaris (2006+) have this capability built into the ECM. Thus far we have found that European and Australian Yaris do not.
The following chart details the scope based on year, transmission type, and DIY method. For methods, one may choose to purchase the Toyota OEM Cruise Control stalk (which mounts to the right side of the steering wheel) or to do the DIY switch method (which uses low cost push button switches and resistors to achieve the same functionality as the OEM stalk).
Part Numbers:
Toyota OEM Cruise Control Stalk:
84632-34011 Toyota OEM Cruise Control Stalk Wire (Required to connect the stalk to the spiral cable, within the steering wheel):
84633-42030 or
84633-02020 (this new PN has replaced the other) Lower Steering wheel cover (with the hole already in it for the cruise stalk):
45184-52130-B0 ECM repair terminal (Used to add the connection to pin 40 of connector A21 of the ECM on Yaris where "wiring to the ECM" is required - Quantity 1 required):
82998-24250 Spiral Connector Repair Terminals (Used to add the two pins to the steering column end of the spiral cable on Yaris where "Extra pins to the spiral cable" is required - Quantity 2 required):
82998-12870 Cruise Control Clutch Switch (Required for all Manual Transmission Yaris):
88280-14030 Here is my complete installation guide for installing cruise control on any 2006-2011 US/Canada/PR Yaris with the OEM Cruise Control Stalk:
http://tinyurl.com/CruiseDIY Threads with specific information / DIYs:
1. The original thread where we discussed if this could be done and made the discovery that it could:
Can we do this? (aka The DIY Cruise Control Thread) 2. My DIY for the
2 or 4 switch method. This thread details what is required to assemble the DIY switches and connection of them to the spiral cable connector on 2009+ Yaris, which have the wiring in place from the ECM to the steering column.
DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag 3. Vince87's DIY for 07-08 (really 06-08) detailing the
ECM pin connection and
clutch switch installation using the 2 or 4 switch method:
DIY Cruise Control on 07-08 Yaris (step by step) 4. PeteZNY's DIY for installing the
OEM stalk. This thread details pulling the airbag to install the OEM stalk on an 09:
Link to a thread or page that is not in the archive 5. A link to a post detailing my
Cruise Control Indicator Module, which provides a visual indicator that cruise control is on for Yaris which don't have an indicator on the cluster:
DIY Cruise Control on 07-08 Yaris (step by step) 6. A DIY that I put together that shows how to disconnect the ECM connector an how to install the pin in position 40 of connector A21:
DIY - How to remove or insert a pin on the ECM Connector A21 7. I have some stalks with the wire and mounting screws for sale (I also have a couple of the cruise control clutch switches, required for MT cars):
FS: OEM Cruise Control Stalk with Wire and Screws 8. I also have some of the repair pins for the ECM connector and the steering column connector:
FS: DIY Cruise Control Pin Kits The combination of the material in the above threads covers everything required from the chart above. You may have to use parts from more than one to cover your particular installation.
FAQs not covered above:
Where can I get the OEM stalk? From a Toyota dealer, eBay or junkyards. The stalk for the Yaris is also used on the following Vehicles:
Camry 04-09
ES300 04-09
Scion TC 04-09
Sequoia 04-09
4Runner 04-09
Corolla 08-09
ES350 06-09
FJ 06, 08
GS450H 06-09
GX470 04-09
Highlander 04-09
IS F 07-09
IS250 05-09
Land Cruiser 04-09
LX470 04-09
LX570 07-09
Prius 04-09
RAV4 04-09
RX330 04-09
RX400H 05-09
Scion xB 07-09
Scion xD 07-09
Tundra 04-09
The stalk wire is also used on the following vehicles:
Corolla 08-09
RAV4 05-08
Replies 415
goku87AK · Jan 30, 2010#2So far this is the cheapest place I could find it:
http://www.google.com/products?q=airtex%201s5850 $14.62 + S&H
---------------------------
Various shipping rates at the time of writing (basically $7.49 for CONUS):
AK - Anchorage (99501) . . . . $9.84
CO - Denver (80002) . . . . . . .$7.49
CA - Los Angeles (90001) . . . $7.49
FL - Tampa (33601) . . . . . . . .$7.49
MO - Kansas City (64101) . . . $6.13
NY - New York (10001) . . . . . .$7.49
WA - Spokane (99201) . . . . . .$7.49
127.0.0.1NE · Jan 30, 2010#3swiddCentral Alabama, GOD BLESS AMERICA · Apr 8, 2010#4The clutch switch for Manual Transmission sells for $22.70 + tax at my local Toyota Dealer Parts Department. That should come out to the same, or less than, the above quoted $17 + shipping.
Also, Radio Shack, Lowe's, Home Depot and SEARS do NOT carry any four-way switches.
fcharlanCanada · Apr 9, 2010#5Hi everybody, I have a Canadian 2007 Yaris and was wondering if someone from Canada tried the DIY Cruise control on their vehicle? I read that the ECM might not be compatible.
Thanks
Dan
CTScottThread starterUSA, CT · Apr 9, 2010#6 Originally Posted by
fcharlan ↑ Hi everybody, I have a Canadian 2007 Yaris and was wondering if someone from Canada tried the DIY Cruise control on their vehicle? I read that the ECM might not be compatible.
Thanks
Dan
Canadian ECM's are fine. I am aware of a least a couple of people from Canada who have added DIY CC.
fcharlanCanada · Apr 9, 2010#7 Originally Posted by
CTScott ↑ Canadian ECM's are fine. I am aware of a least a couple of people from Canada who have added DIY CC.
Thanks a lot for the info. I will try it.👍
carlosgil5Hermosillo, Mexico · Apr 14, 2010#8Guys I really want to do this, I just bought a 2010 AT Mexican Yaris from the local dealer, but I don´t know if there´s any difference between mexican, american or canadian yaris. Am really close to the Arizona Border so I can easily buy the required parts but am afraid my ECM is not compatible, any ideas?
CTScottThread starterUSA, CT · Apr 14, 2010#9 Originally Posted by
carlosgil5 ↑ Guys I really want to do this, I just bought a 2010 AT Mexican Yaris from the local dealer, but I don´t know if there´s any difference between mexican, american or canadian yaris. Am really close to the Arizona Border so I can easily buy the required parts but am afraid my ECM is not compatible, any ideas?
Mexican Yaris get a different ECM than US and Canadian ones, so you would definitely have to test it to see. The place to start is to measure the voltage on the ECM pin 40, with the ignition in the on position. If you see 12 Volts on that pin, then there's a good chance that it will work.
If you shine a flashlight around on your instrument cluster, do you see the two icons for cruise control?
carlosgil5Hermosillo, Mexico · Apr 15, 2010#10Ok, thanks for the info CTScott, am gonna check voltage and instrument cluster before start buying stuff ...So many things to do with this yaris.👍
CTScottThread starterUSA, CT · May 17, 2010#11 Originally Posted by cpchri1 ↑
Hi CTScott -
I have an auto 2010 Yaris 5 door hatch (U.S.) with the power package, I have the CC lamps on my speedometer counsel (unlit at this time), and want to put in the DIY CC. In your post you reference the following part numbers:
Toyota OEM Cruise Control Stalk: 84632-34011
Toyota OEM Cruise Control Stalk Wire (Required to connect the stalk to the spiral cable, within the steering wheel): 84633-42030
Lower Steering wheel cover (with the hole already in it for the cruise stalk):45184-52130-B0
However you also reference PeteZNY post (2009 Yaris 3 door hatch with power package) and he references the following part numbers:
84632-08021 Cruise control switch
84633-02020 Cruise switch wire
90159-50199 Screws (2)
But I'm confused??? What parts should I order?
Thanks!
CPCHRI1 Eastern WA State
2010 Yaris - Added OEM RS3200 Security System, OEM Ipod connector, OEM Bluetooth
2009 Matrix - Added OEM RS3200 Security System, OEM Ipod connector, OEM Bluetooth
2009 Camry - Don't own techstream so had dealer tech add Security System, OEM Bluetooth (note: Toy tech messed it up RS3200 security install)
1985 Toyota PU 22R (w/ LC Engineering timing case conversion kit and hardened OH Cam)
The EPC shows the 84633-02020 cable as being for the Corolla or Matrix, whereas 84633-42030 is for the Yaris and RAV4.
It shows the 84632-08021 stalk as being for a bunch of cars, not including the Yaris, where as 84632-34011 is shown for a bunch including the Yaris.
Apparently, in these two cases the parts not listed for the Yaris do work with the Yaris as well.
The screws are needed. The lower steering column cover is optional. You can either drill a hole for the stalk, or buy the lower cover with the hole already in it.
dingbatMid-Turn (probably late apexing) · May 18, 2010#12Just did this mod today on my '10, 3door, base trim.
Soooo very easy and way cheaper than what the dealer wanted for an aftermarket setup at time of sale!
Thanks to everyone who put all the info together!🙇👍
sk8manmikeCO · May 19, 2010#13I think I'm going to make a video DIY for this mod since it seems to be so popular. I just wanted to make sure that no one else has already made one - I don't want to be THAT guy 👍
ricepowerSaudi Arabia · May 24, 2010#14Is the Instrument Cluster for 09-10 model is bolt-on to 06-08 model? Goal is to have my yaris '07 model with CC indicator on Instrument panel
CTScottThread starterUSA, CT · May 24, 2010#15 Originally Posted by
du2efs ↑ Is the Instrument Cluster for 09-10 model is bolt-on to 06-08 model? Goal is to have my yaris '07 model with CC indicator on Instrument panel
The newer cluster will work on the previous years, but I don't believe that the cruise control indicators will work, as the ECM has to send the message via CAN bus to the cluster to light up the indicator. From experimentation that I have done, I have noticed that an 07 ECM doesn't send the asynchronous message to the cluster when cruise control is activated.
CTScottThread starterUSA, CT · May 24, 2010#16 Originally Posted by
du2efs ↑ Is the Instrument Cluster for 09-10 model is bolt-on to 06-08 model? Goal is to have my yaris '07 model with CC indicator on Instrument panel
Also, I am about 90% sure that your car will not have the cruise control functionality built into its ECM, since it seems to be just USDM cars that have it.
ricepowerSaudi Arabia · May 24, 2010#17 Originally Posted by
CTScott ↑ Also, I am about 90% sure that your car will not have the cruise control functionality built into its ECM, since it seems to be just USDM cars that have it.
With your experience, will you please add your earlier post the P/N's of ECM with CC functionality 👍
CTScottThread starterUSA, CT · May 24, 2010#18 Originally Posted by
du2efs ↑ With your experience, will you please add your earlier post the P/N's of ECM with CC functionality 👍
89661-52F10
89661-52F11
89661-52F11
89661-52G30
89661-52G50
89661-52G50
89661-52G51
89661-52F01
89661-52G40
89661-52G40
89661-52G30
89661-52G41
89661-52E90
89661-52E91
89661-52J50
89661-52J40
89661-52J30
ricepowerSaudi Arabia · Jun 12, 2010#19Moderators, pls have this thread sticky! please ... Originally Posted by
CTScott ↑ 89661-52F10
89661-52F11
89661-52F11
89661-52G30
89661-52G50
89661-52G50
89661-52G51
89661-52F01
89661-52G40
89661-52G40
89661-52G30
89661-52G41
89661-52E90
89661-52E91
89661-52J50
89661-52J40
89661-52J30
SaggioSeattle WA, · Jul 6, 2010#20Who has done this on an 08 USDM Liftback and it worked?
johnliu38Hsinchu City, Taiwan · Jul 21, 2010#21I wodner if I can do the same trick on my Taiwanese version of 2010 Yaris Hatch Back because I heard its ECM has built-in cruise control function, but got locked. Some people charge US$250 for hacking the ECM and enable the CC function... Not sure if it's really locked or not... Is there anyway I can do to identify the CC function of my Yaris?
CTScottThread starterUSA, CT · Jul 21, 2010#22 Originally Posted by
johnliu38 ↑ I wodner if I can do the same trick on my Taiwanese version of 2010 Yaris Hatch Back because I heard its ECM has built-in cruise control function, but got locked. Some people charge US$250 for hacking the ECM and enable the CC function... Not sure if it's really locked or not... Is there anyway I can do to identify the CC function of my Yaris?
Check to see if you have the two wires on the steering column for cruise (and the two cruise control icons on the cluster). If they are there, then you can do a real quick test by grounding the blue wire (with the ignition on) and the cruise control on icon should light up. If the wires aren't there, then you can check the voltage on the ECM pin 40. If there's 12V on that pin with the ignition on, then cruise is enabled, but just the wiring needs to be run.
WolfWingsKansas City, MO, USA · Jul 21, 2010#23 Originally Posted by
Saggio ↑ Who has done this on an 08 USDM Liftback and it worked?
Did it on my 5-speed '07 USDM Liftback, had to run the wire to/from pin 40 on the ECM, swiped the other parts from a 5-speed '09 USDM Liftback and everything worked 'out of the box' without issue.
I ran the wire for pin 40 inside the dash along the existing cable harness across to the cabin air filter tray, the elbow joint above that is a flexible coupling gasket-ed on both sides without any locking tabs so I just ran the wire through the cabin fresh-air intake. It has some flanges on the sides in the engine bay for water drainage/catching that I routed the wire out of and over to the ECU. Take off both windshield wipers and the trim bezels all the way across.
tforknergeorgia · Jul 26, 2010#24Saggio- I put the two-switch DIY type on my '08 LB. I ran the wires from the clutch switch and ECM in through the AC drain grommet. I superglued a roller switch from Radio Shack onto the metal bracket beside the clutch pedal for use as a clutch switch. Everything works fine.
Lucas13Fort Lauderdale · Aug 9, 2010#25 Originally Posted by
Saggio ↑ Who has done this on an 08 USDM Liftback and it worked?
I did on mine the 2 Button and works perfectly, I bought the resistors and switches from radio shack and the OEM clutch switch.
This is one of the 🎉est mods it also gives a nice touch of comfort to the yaris, Thank to CtScott that made this possible 🤘
here are some pics
RevssonSoutheast Wisconsin · Aug 9, 2010#26Nice clean install ^ 👏
Lucas13Fort Lauderdale · Aug 10, 2010#27Thanks Revsson!
I try to keep it clean as possible especially for the warranty, you never know!!!
magnum23Aguadilla,Puerto Rico · Oct 13, 2010#28Hi, to everybody, In from Puerto Rico, Im glad that I found this great forum, full of great and interesting info about Yaris. I recently bought a used 2009 Toyota Yaris Sedan, and Im doing some great mods that I have found here in the forum, after reading for a while I decided to do the DIY Cruise Control mod on my sedan, it have oem power locks and power windows, all the wiring is in place, and the cluster have the CC symbols, I installed the oem stalk and wire, but when I tried to turn the Cruise control on, nothings happens. I swapped the stalk with the one in my wifes rav-4 and it didnt worked also, but the one I bought worked in the Rav-4, so the problem is not the stalk, or the wire. Is there any optional procedure or relay that I need to install?
Thanks in advance for your help, looking forward to see my Yaris with cruise.
CTScottThread starterUSA, CT · Oct 13, 2010#29 Originally Posted by
magnum23 ↑ Hi, to everybody, In from Puerto Rico, Im glad that I found this great forum, full of great and interesting info about Yaris. I recently bought a used 2009 Toyota Yaris Sedan, and Im doing some great mods that I have found here in the forum, after reading for a while I decided to do the DIY Cruise Control mod on my sedan, it have oem power locks and power windows, all the wiring is in place, and the cluster have the CC symbols, I installed the oem stalk and wire, but when I tried to turn the Cruise control on, nothings happens. I swapped the stalk with the one in my wifes rav-4 and it didnt worked also, but the one I bought worked in the Rav-4, so the problem is not the stalk, or the wire. Is there any optional procedure or relay that I need to install?
Thanks in advance for your help, looking forward to see my Yaris with cruise.
Does it have an auto or manual transmission?
magnum23Aguadilla,Puerto Rico · Oct 13, 2010#30It have an Auto transmission.
CTScottThread starterUSA, CT · Oct 13, 2010#31 Originally Posted by
magnum23 ↑ It have an Auto transmission.
OK. I just noticed that you said that you have a 2009 Sedan and the wiring was in place. So, you had the blue and brown wires, not just the black horn wire on connector D3 (the one on the bottom of the steering column)?
magnum23Aguadilla,Puerto Rico · Oct 13, 2010#32Yes just double checked and it have the 3 wires in place.
CTScottThread starterUSA, CT · Oct 13, 2010#33 Originally Posted by
magnum23 ↑ Yes just double checked and it have the 3 wires in place.
OK - Just to triple check - We're talking about the connector next to the yellow one on the left side of this picture?
If that's good, look at the part number on the ECM (The silver box on the passenger side of the firewall) and post it. I don't know if anyone from PR has tried the cruise mod, and I think that you might get a different version of the ECM, from what we get here.
magnum23Aguadilla,Puerto Rico · Oct 13, 2010#34Yes that is good, mine is exactly as the picture you posted, where exactly is this part, (The silver box on the passenger side of the firewall)?
CTScottThread starterUSA, CT · Oct 13, 2010#35 Originally Posted by
magnum23 ↑ Yes that is good, mine is exactly as the picture you posted, where exactly is this part, (The silver box on the passenger side of the firewall)?
Pop the hood and look to the left:

magnum23Aguadilla,Puerto Rico · Oct 13, 2010#36Mine is 89661-52J50
CTScottThread starterUSA, CT · Oct 13, 2010#37 Originally Posted by
magnum23 ↑ Mine is 89661-52J50
OK - That's the same as my 09 LB, so the ECM is fine.
Do you have a volt meter and know how to use it?
magnum23Aguadilla,Puerto Rico · Oct 13, 2010#38I dont have one accesible right now? But why I should check? What do you think is the problem?
Thanks in advance.
CTScottThread starterUSA, CT · Oct 13, 2010#39 Originally Posted by
magnum23 ↑ I dont have one accesible right now? But why I should check? What do you think is the problem?
Thanks in advance.
If you measure the voltage between the blue and brown wires (with the ignition in the on position) at the connector under the dash, you should see 12V. If you hold the on/off switch it should drop to 0V and then pop back to 12 when you release it. That's a good starting point.
magnum23Aguadilla,Puerto Rico · Oct 13, 2010#40I will try that tomorrow morning and post the results, thanks for your help, looking forward to that cruise control!!!!
magnum23Aguadilla,Puerto Rico · Oct 14, 2010#41I tried to get a read between the blue and brown wires with a digital multimeter, but It dont display any voltage, Im not really sure but I think Im doing it right. I used a Craftsman digital multimeter, put the knob in the VDC section, in the 20 value, and the cables the black in com, and the red in V, mA. I tried in the end of the plug and directly to the cable and nothing.
What Follows?
Thanks in advance.
CTScottThread starterUSA, CT · Oct 14, 2010#42 Originally Posted by
magnum23 ↑ I tried to get a read between the blue and brown wires with a digital multimeter, but It dont display any voltage, Im not really sure but I think Im doing it right. I used a Craftsman digital multimeter, put the knob in the VDC section, in the 20 value, and the cables the black in com, and the red in V, mA. I tried in the end of the plug and directly to the cable and nothing.
What Follows?
Thanks in advance.
You have the meter setup properly. The important thing is to make sure that the metal tips of the meter probes are actually touching the metal of the connector pins. You want to go in from the side where the blue and brown wires enter the connector.
Also, make sure you have the key in the ON position when taking the measurement.
magnum23Aguadilla,Puerto Rico · Oct 14, 2010#43Ok, I checked again and there is no voltage reading, I tried the same with another plug in the wiring and got a 12v reading, I think there is no voltage getting to the CC switch thorugh the plug.
CTScottThread starterUSA, CT · Oct 14, 2010#44 Originally Posted by
magnum23 ↑ Ok, I checked again and there is no voltage reading, I tried the same with another plug in the wiring and got a 12v reading, I think there is no voltage getting to the CC switch thorugh the plug.
OK. The next thing to check is if the ECM pin is actually there for the blue cruise control wire. You can remove the connector (you press in on the gray part and then lift it to release the connector). If you look in the hole side of the connector, you will see that some holes have metal visible and others do not. Check the pin circled below (note that the connector in this photo does not have visible metal, so it is lacking the pin for cruise control):

magnum23Aguadilla,Puerto Rico · Oct 14, 2010#45I think that is the problem the pin is not there on that side.
CTScottThread starterUSA, CT · Oct 14, 2010#46 Originally Posted by
magnum23 ↑ I think that is the problem the pin is not there on that side.
If that is the case, you'd need to follow the procedure on the first page for the 2008 or older Yaris to add the pin, and then run the wire from it to the blue wire. The brown should be fine, as that one is just a ground.
magnum23Aguadilla,Puerto Rico · Oct 14, 2010#47Ok, but where does the blue wire from the switch should lead? They just cut it on the middle from the cabin to the ECM?
CTScottThread starterUSA, CT · Oct 14, 2010#48 Originally Posted by
magnum23 ↑ Ok, but where does the blue wire from the switch should lead? They just cut it on the middle from the cabin to the ECM?
The wire goes from the ECM to a junction connector that is way up under the left corner of the dash. From there a second wire goes from the junction connector to the connector under the steering wheel.
magnum23Aguadilla,Puerto Rico · Oct 14, 2010#49I will be running that wire tomorrow morning then, Do I need the special connector listed for adding the connection to the ECM or could I tested just passing the cable through the space where it goes on the black plug that goes to the ecm?
Do a regular cable connector works? ( the little square ones)
Thanks for your help!!!
CTScottThread starterUSA, CT · Oct 14, 2010#50 Originally Posted by
magnum23 ↑ I will be running that wire tomorrow morning then, Do I need the special connector listed for adding the connection to the ECM or could I tested just passing the cable through the space where it goes on the black plug that goes to the ecm?
Do a regular cable connector works? ( the little square ones)
Thanks for your help!!!
You definitely want to get one of the real pins for permanent installation, but you can try the "shove a wire in" method for testing. I wouldn't try any other type of pin, as if it gets stuck you'll have a real mess.