nvfool, when I ordered my cruse from scott, I had to send him a personal message to place order. I don't remember how I done that, clicked on his name in one of his posts or clicked on the quick reply in corner of one of his posts?
DIY Cruise Control FAQ (2006-2010 Yaris)
416 posts · 835,665 views · page 9 of 9
Replies continued
You may only need the handleOriginally Posted by geeoye ↑CTScott,
I have a 2011 Yaris Hatchback 5Dr which I bought a week ago. It has a 43K miles on it. It has all the power windows and power doors. I was wondering what do I need to install the Cruise control in it.
Much appreciate it.
Geeoye
Cruise Control Question
My Vitz 2010 model Japanese imported. It already has wiring upto ECM (saw it by removing the cover behind the steering )but my cluster doesn't have any indicators for CC. Do you think if i install OEM CC, my car would be able to handle it? irrespective of the indication on the cluster? if this is the case, i might change my insturmenet cluster.
I have a 2007 Toyota Yaris with Blue and Brown Wire in D3 no A21 pin 40. What am I supposed to do with wire coming from ECM A21 pin 40?
Also, where can I get a Cruise Control Indicator Module? Does CTScott still have some available or is their a wiring diagram that I could build one myself?
Ok, I looked up the electrical drawings for cruise control. D3 goes to AD4, which is a connection between harnesses, and on the other side of the harness connection their is no wire coming out to pin 40 on A21. I got extra repair terminals, so I will put a terminal in the empty side going to pin 40 and solder it to the repair terminal I install in pin 40.
Can you share the diagram of CC. Still curious for the AD4 location... TksOriginally Posted by DanielNorrisII@Gmail.com ↑Ok, I looked up the electrical drawings for cruise control. D3 goes to AD4, which is a connection between harnesses, and on the other side of the harness connection their is no wire coming out to pin 40 on A21. I got extra repair terminals, so I will put a terminal in the empty side going to pin 40 and solder it to the repair terminal I install in pin 40.
dear!Originally Posted by weltall900 ↑My apologies if this has been asked before. I'm going to attempt this project for my wife's car. I'm not super mechanical, but I'm going to try my best and pray that I don't mess up her car! She has a 2007 Yaris with automatic transmission. I'm wanting to use the OEM stalk setup and I've read through much of this thread and the 2006-2011 Yaris – OEM Cruise Control Installation PDF. However, I'm not sure if her car is Sedan with power OR Sedan without power. Not even sure what that means. She has power locks, power windows, manual seats, automatic transmission, manual side view mirrors, and obviously no cruise control. I included an image from the guide here. Which applies to me? The one I circled in RED or the one I circled in BLUE
Picture lost · snag.gy
w/power and w/out power means?
different?
Does my american 2015 Yaris L have prewired cruise control? Hoping for just a plug and play here.
It should just be a matter of mounting and plugging in the control stalk.
Have a look at DIY Cruise Control for 2012 Yaris - Good News!
The 2015 should only be a facelift from 2012.
Have a look at DIY Cruise Control for 2012 Yaris - Good News!
The 2015 should only be a facelift from 2012.
Hoping this thread is still alive. I am about to buy a base model 2010 4 door sedan without power locks/windows and auto transmission. Does this require just the stalk and wire? The guide seems to say it requires running wires to the ECM but a few posts here have confused me if that is needed. Since I don't have the car yet, I can't look but I wanted to get the parts.
My gf has a 2010 Yaris with a stick.
I installed a cruise control stalk I bought online. The dash light comes on showing cruise control is on, but it will not engage?
Do I need to add the clutch sensor?
Can someone please repost the clutch sensor wiring instructions?
I installed a cruise control stalk I bought online. The dash light comes on showing cruise control is on, but it will not engage?
Do I need to add the clutch sensor?
Can someone please repost the clutch sensor wiring instructions?
yes you have to add the clutch switch, without it..the cruise acts like the clutch is stuck in...and just wont do anythingOriginally Posted by OCEANROADS ↑My gf has a 2010 Yaris with a stick.
I installed a cruise control stalk I bought online. The dash light comes on showing cruise control is on, but it will not engage?
Do I need to add the clutch sensor?
Can someone please repost the clutch sensor wiring instructions?
as for the wiring..a lil searching and you should find it
Read the last post here: DIY: 2006-2011 Yaris OEM Cruise Control Complete Installation
Hi every one!
I'm fom Viet Nam , my car is toyota yaris/vios 2011 Mt, Asia production, can I install cruise control for my car? thanks alot!
I'm fom Viet Nam , my car is toyota yaris/vios 2011 Mt, Asia production, can I install cruise control for my car? thanks alot!
Your car does not have the programming in the ecu if it didn't come with cc from the factory. Only North American (Canada/US/PR) models have it built in and base models just dont include the stalk to activate it (or the clutch as well if MT). You'll need to look at aftermarket cruise control kits.Originally Posted by Xuanbinhktv ↑Hi every one!
I'm fom Viet Nam , my car is toyota yaris/vios 2011 Mt, Asia production, can I install cruise control for my car? thanks alot!