What year is it and which engine does it have?Originally Posted by jasonk1123 ↑Hi there would anybody be able to tell me if my T3 Yaris will support cruise control? It is a south African spec. I am not sure if i will need a cruise control module?
Or, how can i check if it has
DIY Cruise Control FAQ (2006-2010 Yaris)
416 posts · 835,665 views · page 8 of 9
Replies continued
Thanks for the reply...
It is a 2008 1.3 petrol 4 cylinder
It is a 2008 1.3 petrol 4 cylinder
I was going to say no, but looking at the specs for some T3's it looks like cruise was an option. Take a look at my DIY (linked under my signature picture). To be sure, start with checking for the presence of the connector D3 wires on the steering column, and if they are not present check for the presence of the pin 40 wire on the ECM. Finally, if that is not present, check for 12V to be present on that pin with the ignition in the on position.Originally Posted by jasonk1123 ↑Thanks for the reply...
It is a 2008 1.3 petrol 4 cylinder
there is D3 when I earth the blue wire there is no icon(assuming that it may be because there is no space on the cluster for that light?) there is no pin in 40 on ECM plug... btw the D3 has more than just a black wire out of it, it ahs a brown and blue, however they are not in the specified places
Picture lost · www.dropbox.com
Picture lost · www.dropbox.com
OK. By the wires present it looks like you have steering wheel audio controls (or at least you car is wired for it).Originally Posted by jasonk1123 ↑
So, the next test is measuring the voltage on the ECM pin 40. You can pull the rubber plug and stick a piece of wire in there to take the measurement.
Hi ÇTscott, can i pull the ECM plug off with the battery connected? Btw on the plug side there is no wire coming from pin 40 of the plug
Yes - You can pull it with the battery connected.Originally Posted by jasonk1123 ↑Hi ÇTscott, can i pull the ECM plug off with the battery connected? Btw on the plug side there is no wire coming from pin 40 of the plug
You will need to pull out the little rubber hole plug (easiest way is to stick a sewing pin into the hole and push the plug out the back side). Once the plug is out you can plug the connector back in and stick a small piece of wire into the hole to make contact with the ECM pin. Then, turn the key to the ON position and measure the voltage on that pin.
OK awesome, will try that and let you know?
BTW I did read the DIY section when i first started, wasn't sure how to check if there were preparations for the cruise control already ion place, but now i know, thanks a ton, will let you know what the result is
BTW I did read the DIY section when i first started, wasn't sure how to check if there were preparations for the cruise control already ion place, but now i know, thanks a ton, will let you know what the result is
Hi CTscott
I have tried to place a led light in there, i earthed the one side and shoved the + side in the whole, it did not come on...
must i try it with the + side on battery and shove the - side in there? The reason i am using the LED because i dont have a meter hereXD
I have tried to place a led light in there, i earthed the one side and shoved the + side in the whole, it did not come on...
must i try it with the + side on battery and shove the - side in there? The reason i am using the LED because i dont have a meter hereXD
Hi CTscott
I have tried to place a led light in there, i earthed the one side and shoved the + side in the whole, it did not come on...
must i try it with the + side on battery and shove the - side in there? The reason i am using the LED because i dont have a meter hereXD
I have tried to place a led light in there, i earthed the one side and shoved the + side in the whole, it did not come on...
must i try it with the + side on battery and shove the - side in there? The reason i am using the LED because i dont have a meter hereXD
oops double post:)
I have tried the + and - and cant get the light to shine:(
Oh well at least I tried... Now it is time for me to find a suitable cc for my Yaris. If anyone has any sudgestions let me know, Thanks a mil
I have tried the + and - and cant get the light to shine:(
Oh well at least I tried... Now it is time for me to find a suitable cc for my Yaris. If anyone has any sudgestions let me know, Thanks a mil
If you can get your hands on a voltmeter try that instead. The +12V on that pin is not intended to source current, but rather is just a high impedance ADC looking for the various resistances fed by pressing the different switches on the stalk.
ah so there is hope.
Will test it today and let everyone know
Will test it today and let everyone know
Ok so I got 0.3 DCV, it was steady like not dropping or anything. what should i be looking for?
Like I asked on your other thread - What year is your Yaris, as that makes a difference in the wiring?Originally Posted by hockysa ↑Hi is there any information anywhere on these installs?
I've acquired a second hand AP800 and want to install it on my Yaris and have figured out the wiring except for the accelerator pedal.
OK. The accelerator pedal has a 6 pin connector.Originally Posted by hockysa ↑oh sorry didn't see a reply
it's a 2007 Yaris
1 - White: VCP2 (Sensor 2 power)
2 - Brown: EPA2 (Sensor 2 ground)
3 - Light blue: VPA2 (Sensor 2 output)
4 - Black: VCPA (Sensor 1 power)
5 - Green: EPA (Sensor 1 ground)
6 - Red: VPA (Sensor 1 output)
I haven't seen the install manual for the AP800 for the Yaris, but looking at the pinout of the AP800 it has a high and low throttle position sensor connections.
On the Yaris the VPA signal would be the low one (2.6 to 4.5 V at full throttle) and VPA2 would be the high one (3.4 to 5.0 V at full throttle).
I don't have the info for the Corolla, but the pinout order is likely the same with just the wire colors being different. You can verify that by measuring the voltage on the pins where the "power" pins should have 5 volts on them and the grounds zero.Originally Posted by hockysa ↑Awesome that's perfect
thanks!
you don't also happen to have the same thing for a 2006 Corolla do you?
It's also a 6pin plug but different configuration
*edit*
also where did you find it?
because I've been searching for hours and got nothing
*edit edit*
just googled corolla VCP2 and found it :S
I found a manual for the aftermarket cruise online, but it was not for a Yaris.
http://nicolas.bct.free.fr/Regulateu...rateur_HDi.pdfOriginally Posted by hockysa ↑Yeah I thought the same too but the order is different
yeah? could you link it to me anyway please?
I ran into the diagram for the 05 Corolla and it shows:
1. Yellow - EPA2
2. White - VPA2
3. Yellow - EPA
4. Black - VCP2
5. Green - VPA
6. Black - VCPA
Will it respond to the "Diagnostics mode" listed in the manual?Originally Posted by hockysa ↑omfg so lame... followed instructions to calibrate and now it doesn't work fml
linked the manual I was using
http://www.lupo3lklub.dk/pdf/AP900C_...ion_Manual.pdf
my unit is actually an AP800 but the seemed to have replaced that with a 2 in 1 type unit the AP900c
Hey CTScott,Originally Posted by CTScott ↑Since the car is built with a spiral cable that does not have enough wires to support cruise control, it is unlikely that the ECM is programmed for it.
In doing a bit more research on the Axio Fielder, the ones with the same engine as the Yaris (1NZ-FE) do not support cruise control, but the ones with the 2ZR-FE engine do.
maybe it is again a stupid question about the cruise control in the european Yaris XP9.
I read that you have not found any model in the EWDs which has CC built in.
Pointing to the above quote I post it to clarify for myself. Because all my trials on the net gave only answers for the smaler engine types.
In my case it is the TS 1.8 (2ZR-FE engine) with the ECM 89661-52F30. So far as I could investigate built only for Europe and Japan.
Additional: This car was only built in Japan, so maybe this is a chance to have CC programmed.
If it won't be in I am going probably with the ROSTRA 250-1873. The European solution will be more than double priced (waeco magicspeed ms-880).
Thanks for your work here it is an outstanding platform with a lot of useful stuff.
👍 from Germany
Hello CTScott, I know you said that only cars with US/Canada specs support CC, but I need to know if my 2014 yaris with mexican specs supports it since the car appears to be fully wired (the d3 has the black wire for the horn, the blue and brown for the CC and aparently 3 more wires for audio controls). It also appears to have the CC indicator on the instrument panel along with the vsc/trac which is not an option for sedans in mexico. Is there any option for me in case OEM CC can't be installed? I take highways a lot and it's not fun for my leg.
Yes. Mexico spec cars are the same as US spec ones, so it will work for you.Originally Posted by Gitaniio ↑Hello CTScott, I know you said that only cars with US/Canada specs support CC, but I need to know if my 2014 yaris with mexican specs supports it since the car appears to be fully wired (the d3 has the black wire for the horn, the blue and brown for the CC and aparently 3 more wires for audio controls). It also appears to have the CC indicator on the instrument panel along with the vsc/trac which is not an option for sedans in mexico. Is there any option for me in case OEM CC can't be installed? I take highways a lot and it's not fun for my leg.
I tried to test the CC with a two switch set from one of your tutorials but nothing happened, then I tried to bridge the blue and brown cables and nothing. I did the tests because I don't want to buy the stalk and the wire without knowing for sure if the car's CC is enabled. Am I doing something wrong? Is there any other way to find out? 😕Originally Posted by CTScott ↑Yes. Mexico spec cars are the same as US spec ones, so it will work for you.
Thanks for answering!
Check for the presence of the blue wire on the ECM connector. The ones from the steering column may only run to the junction block under the dash top.
There's nothing in the 40 pin, should I test it with a voltimeter? If so, please tell me the right steps to do it because I don't want to set the car on fire 😆Originally Posted by CTScott ↑Check for the presence of the blue wire on the ECM connector. The ones from the steering column may only run to the junction block under the dash top.
If you pull the rubber plug you can stick a small piece of wire in the hole to take the voltage measurement. Turn the key to the on position and take the measurement with the red on that wire and the black lead on a ground.
Unfortunately there was no voltage there. Is there any other way to install a CC in my yaris? Thank you for your time.Originally Posted by CTScott ↑If you pull the rubber plug you can stick a small piece of wire in the hole to take the voltage measurement. Turn the key to the on position and take the measurement with the red on that wire and the black lead on a ground.
Originally Posted by Gitaniio ↑Unfortunately there was no voltage there. Is there any other way to install a CC in my yaris? Thank you for your time.
Your options would be to either switch the ECM to a US spec one or use an aftermarket cruise control system.
CTScott,
I sent you a couple PM's but the forum isn't showing that I've sent them. Let me know if you've received them.
They were regarding parts availability for cc install on my 2007 S Sedan AT no power.
I sent you a couple PM's but the forum isn't showing that I've sent them. Let me know if you've received them.
They were regarding parts availability for cc install on my 2007 S Sedan AT no power.
PM repliedOriginally Posted by winston856 ↑CTScott,
I sent you a couple PM's but the forum isn't showing that I've sent them. Let me know if you've received them.
They were regarding parts availability for cc install on my 2007 S Sedan AT no power.
Hi all..
My cruse control stopped working last night on the way home, and so I removed the switch, and took it apart, and low and behold, the ON/OFF pushbutton wires, one broke off its solder point.
Stripped the wire a bit, and re soldered, and bingo! back in business..
regards
My cruse control stopped working last night on the way home, and so I removed the switch, and took it apart, and low and behold, the ON/OFF pushbutton wires, one broke off its solder point.
Stripped the wire a bit, and re soldered, and bingo! back in business..
regards

Interesting. I haven't heard of that happening yet, but there is always a first. Thanks for sharing, as I am sure you will not be the last.Originally Posted by CB900F2 ↑Hi all..
My cruse control stopped working last night on the way home, and so I removed the switch, and took it apart, and low and behold, the ON/OFF pushbutton wires, one broke off its solder point.
Stripped the wire a bit, and re soldered, and bingo! back in business..
regards
Any idea how difficult or whether this would be possible on the 2015 model? I did it once before on the 2007 model but I have no idea how much different the 2015 model might be. Would the connectors even be the same?
Hayden i did it on my 2015, is Quick and easy,
Great, thank you. Did you use the same instructions as the 2012 model?Originally Posted by Eduardo_mty ↑Hayden i did it on my 2015, is Quick and easy,
Yes... If i remember well, i open a thread
Cruise control, yaris 2015, 5 Speed, is the name of my thread
The 2015 is the same as far as the stalk goes and does not require any additional wiring, like your 2007 did. If it is a MT, you will need a clutch switch as well.Originally Posted by hayden ↑Any idea how difficult or whether this would be possible on the 2015 model? I did it once before on the 2007 model but I have no idea how much different the 2015 model might be. Would the connectors even be the same?
Awesome, thank you!Originally Posted by Eduardo_mty ↑Cruise control, yaris 2015, 5 Speed, is the name of my thread
Hello guys quick question, I have looked through the diagrams and I cant seem to find the cable that attached to the Cruise Control Clutch Switch (Required for all Manual Transmission Yaris): 88280-14030. Can anybody help me out with the part number of that cable?
thank you
thank you
No need - The cable is part of the harness, so it is already present on your car. Look up above the clutch arm and you will see the white connector taped to the harness above it.Originally Posted by bambam28 ↑Hello guys quick question, I have looked through the diagrams and I cant seem to find the cable that attached to the Cruise Control Clutch Switch (Required for all Manual Transmission Yaris): 88280-14030. Can anybody help me out with the part number of that cable?
thank you
Originally Posted by LeBnomiS ↑Hi CTScott, thanks for all the help you are providing.
I have a 2011 liftback MT, no power. According to your guide, there is no need to add wiring from the ECM to steering column for all liftbacks 2009-2011.
Someone asked earlier in the thread if the cruise would work for this particular model and you answered he needed to add the connector D3 pins and run wire to the ECM.
I am confused. Will I need to run the wire or will it be plug and play ?
Thanks again for you time !
My guide is correct for your car. The other person did not have the same...
I have a Canadian 2008 sedan I bought a kit online years back it only works for the first 5 to 10 minutes of driving the Yaris and then stops working like I can get on to the highway set it at 100 and it will hold there till I hit the brakes.. but the switch stops working like no exceleration or deceleration you can't even turn it off or cancel with the stock so I'm lost on why it's doing this anyone have some insight?
What type of kit did you buy?Originally Posted by colindoling ↑I have a Canadian 2008 sedan I bought a kit online years back it only works for the first 5 to 10 minutes of driving the Yaris and then stops working like I can get on to the highway set it at 100 and it will hold there till I hit the brakes.. but the switch stops working like no exceleration or deceleration you can't even turn it off or cancel with the stock so I'm lost on why it's doing this anyone have some insight?
Hi Scott, I have a 2010 Yaris sedan with manual trans, pwr windows/locks and ac. Can you send me the list of parts required for the cruise control and pricing?
I tried sending a pm and it did not seem to work so just posting here...
Thanks!
Max
I tried sending a pm and it did not seem to work so just posting here...
Thanks!
Max
Hi Scott, I have a Yaris 2016 Hybrid with AT and TSS . The car is for European market (Croatia).
Can you send me the list of parts required for the cruise control and pricing?
If it helps I can send VIN number.
Sorry for my bad english
Can you send me the list of parts required for the cruise control and pricing?
If it helps I can send VIN number.
Sorry for my bad english
i bought a rostra kitOriginally Posted by CTScott ↑What type of kit did you buy?
I bought a cruise kit from CT Scott about a year ago for my French built, 2015 Yaris L automatic, Took about 45 minutes to install, plug and play. Looks like it was installed at the factory and still works great.
I would like to get a kit for a 2012 sedan. Thank you