Yarisworld Archive

DIY Cruise Control FAQ (2006-2010 Yaris)

416 posts · 835,665 views · page 2 of 9

Replies continued

magnum23Aguadilla,Puerto Rico · Oct 14, 2010#51
Thanks for your real fast reply, I will try the wire method tomorrow, and order the special pin from the local dealer tomorrow. I will post if it works.
magnum23Aguadilla,Puerto Rico · Oct 15, 2010#52
Update:

I did the wiring, but the cruise control icon is not showing up in the cluster, but I did what you told before, to measure the volt, and now is getting the 12 volt, and when I press the On/Off bottom on the stalk the volt drop to 0.1
CTScottThread starterUSA, CT · Oct 15, 2010#53
Originally Posted by magnum23 ↑
Update:

I did the wiring, but the cruise control icon is not showing up in the cluster, but I did what you told before, to measure the volt, and now is getting the 12 volt, and when I press the On/Off bottom on the stalk the volt drop to 0.1
Now that you are seeing the correct voltage, have you tried it on the road to see if it works (even though the cluster doesn't light)? If that works, then check the part number on the back of your cluster.
magnum23Aguadilla,Puerto Rico · Oct 15, 2010#54
Ok, I did a road test and is working, but for some reason is not showing it on the cluster, and it have the light for it, the cluster part number is 83800-52S10
157540-8052

Thanks in advance.
CTScottThread starterUSA, CT · Oct 15, 2010#55
Originally Posted by magnum23 ↑
Ok, I did a road test and is working, but for some reason is not showing it on the cluster, and it have the light for it, the cluster part number is 83800-52S10
157540-8052

Thanks in advance.
OK - 83800-52S10 is listed as being "Puerto Rico Spec". That must mean that for whatever reason the CC indicators are not active. Since your ECM fully supports CC, it sends the messages over CAN bus to the cluster, but your cluster just ignores them. You could pick up a US spec cluster off Ebay and then you'd have the working indicator.
magnum23Aguadilla,Puerto Rico · Oct 15, 2010#56
Ok, I think I will leave it without the CC indicator because changing the cluster implies problems with the warranty, unless I program the current mileage on the new cluster, I dont know why the ECM support CC and something as simple as the cluster, and having the light indicator don't. If somebody find a way to activate that option I will be glad to try it.

CtScott I'm real thankful to you for all your help, and everybody in this excellent Forum.
I will be around trying some different projects and mods from here.
magnum23Aguadilla,Puerto Rico · Oct 15, 2010#57
I dont now it thats just it, but I opened up the cluster and it doesnt have any Led soldered in the cruise and set indicators and also in the Abs indicator, If I solder an Led on the board, should it Do the work? If yes where I can pick up a small led or light to test it?

Thanks in advance.

Update:
I found a post where a member mod the led of the cluster, I will be ordering the leds from ther to see if its works.
magnum23Aguadilla,Puerto Rico · Oct 16, 2010#59
I have another question? I did the wiring (blue wire) directly from the computer to the stalk, even when the stock wire goes from the stalk, somewhere else, does that have something to do with the CC signal don't reaching the cluster? I'm just assuming that maybe is an extra wire in the cluster to get the signal that mine doesn't have.
CTScottThread starterUSA, CT · Oct 16, 2010#60
Originally Posted by magnum23 ↑
I have another question? I did the wiring (blue wire) directly from the computer to the stalk, even when the stock wire goes from the stalk, somewhere else, does that have something to do with the CC signal don't reaching the cluster? I'm just assuming that maybe is an extra wire in the cluster to get the signal that mine doesn't have.
The CC signal is sent via CAN bus message, so there's nothing wiring related to activate it. We've seen this kind of thing quite a bit, where clusters have a capability, but in a particular area of the world it's not active. Unfortunately, there's no practical way to activate the non-active features.
teddyOntario, Canada · Oct 25, 2010#61
Hey CTScott, can you take a look at this for me? Since Toyota Canada is "recommending" the Rostra CC units be removed for a full refund, I think I'd like to take the opportunity to install the OEM CC unit.

Here is a list of the parts I've compiled which I should need. It's for a Canadian 2008 AT.

https://spreadsheets.google.com/ccc?...thkey=CN6w_OoF

Before I go ahead and order I'd like to make sure I'm ordering the right stuff!

Cheers 🙇
ShinareOklahoma City, OK · Oct 25, 2010#62
Originally Posted by teddy ↑
... Toyota Canada is "recommending" the Rostra CC units be removed for a full refund...
Yikes, thats the kind of CC I have in my yaris from the dealership. Any reason its not good to have?
CTScottThread starterUSA, CT · Oct 25, 2010#63
Originally Posted by teddy ↑
Hey CTScott, can you take a look at this for me? Since Toyota Canada is "recommending" the Rostra CC units be removed for a full refund, I think I'd like to take the opportunity to install the OEM CC unit.

Here is a list of the parts I've compiled which I should need. It's for a Canadian 2008 AT.

https://spreadsheets.google.com/ccc?...thkey=CN6w_OoF

Before I go ahead and order I'd like to make sure I'm ordering the right stuff!

Cheers 🙇
That's it. By the way, within about a week I will have the ECM and Connector D3 pins for sale for less that half of that.
teddyOntario, Canada · Oct 25, 2010#64
Originally Posted by CTScott ↑
That's it. By the way, within about a week I will have the ECM and Connector D3 pins for sale for less that half of that.
Awesome!! I'll have to contact you for them soon. I'm going to get the dealership to remove the Rostra unit at my next scheduled maintenance appt, in a month or two. I'll order what I need after that.
magnum23Aguadilla,Puerto Rico · Oct 25, 2010#65
That's good to know, Scott as soon as you have the ECM repair terminals Im interested in one.
Thanks in advance.
teddyOntario, Canada · Oct 25, 2010#66
Sorry to be spamming up this thread, but has anybody done a DIY guide for the OEM stalk on a 07-08 Yaris?
CTScottThread starterUSA, CT · Oct 25, 2010#67
Originally Posted by teddy ↑
Sorry to be spamming up this thread, but has anybody done a DIY guide for the OEM stalk on a 07-08 Yaris?
There's not a complete one for 07-08 with the OEM stalk, but it's basically a combination of the 07-08 with the switch method and the 09 with the OEM stalk.

DIY Cruise Control FAQ (2006-2010 Yaris)
tunnelpatHighland falls ny · Nov 5, 2010#68
I installed mine today..it was easy..bought the stalk from ebay for 19.99, the wireing harness and two screws from Toyota for 40.00. Whole thing cost me 70 bucks. :)
MullDoonNew Jersey · Nov 7, 2010#69
installed cruise in my 2010 yaris works great.total cost $14 had to buy 100ft of wire thats all radio shack had.total time of install 1hr with going to store very simple. glad i did some looking around before paying $399 for rostra install. I have 1000 mi on car couldn't do my commute without cruise. thanks
ibanezjeepguyMyrtle Beach, SC USA · Dec 13, 2010#70
do I need to order this for my 2010 w/ power package.

Toyota OEM Cruise Control Stalk Wire (Required to connect the stalk to the spiral cable, within the steering wheel): 84633-42030

I got the stalk & cover w/ hole in UPS today but no wiring came with the stalk as it does from the dealer.
CTScottThread starterUSA, CT · Dec 13, 2010#71
Originally Posted by ibanezjeepguy ↑
do I need to order this for my 2010 w/ power package.

Toyota OEM Cruise Control Stalk Wire (Required to connect the stalk to the spiral cable, within the steering wheel): 84633-42030

I got the stalk & cover w/ hole in UPS today but no wiring came with the stalk as it does from the dealer.
Yes. The stalk and the wire are separate parts from the dealer.
ibanezjeepguyMyrtle Beach, SC USA · Dec 16, 2010#72
forgot to ask, anyone know what size the bolts/screws are that hold the OEM CC Stalk to the car, I think I read it was M5 somewhere ?
CTScottThread starterUSA, CT · Dec 16, 2010#73
Originally Posted by ibanezjeepguy ↑
forgot to ask, anyone know what size the bolts/screws are that hold the OEM CC Stalk to the car, I think I read it was M5 somewhere ?
M5 x 0.8
ibanezjeepguyMyrtle Beach, SC USA · Dec 17, 2010#74
thats great, I had some of these screws laying around from replacing x-clamps on xbox 360. installed the switch and sw back cover tonight, very quick install, if it weren't so dark it probably would've taken half the time!
just a note to future installers, I could not bare fist grip a torx screwdriver to get the airbag screws out. they were in there tight! I had to get my t30 socket on a 1/4" wrench to loosen them. taking off the steering wheel was a breeze, 19mm socket on the nut, held the sw with my legs while yanking the socket wrench did it. did not need a puller like other installers have noted the steering wheel pulled off the shaft effortlessly. removed the ground wire and replaced w/ the wire from the kit I ordered.
done deal. thanks for all the great write-ups
teddyOntario, Canada · Dec 28, 2010#75
Ok I have my OEM stalk mounted but do not have the necessary cables hooked up to actually make it work yet.

Is there anyone out there who has done this on an 06-08 that can help me out?

I have the ECM repair terminal and spiral connector repair terminals (thanks scott!). The only part I've figured out is where to connect the spiral connector terminals on the connector D3. I don't know where these connect to on the other end, nor where I use the ECM repair terminal.

I've been using Vince87's DIY guide guide for this part, but unfortunately I really don't know what I'm doing when I get past the plug & play connectors!
CTScottThread starterUSA, CT · Dec 28, 2010#76
Originally Posted by teddy ↑
Ok I have my OEM stalk mounted but do not have the necessary cables hooked up to actually make it work yet.

Is there anyone out there who has done this on an 06-08 that can help me out?

I have the ECM repair terminal and spiral connector repair terminals (thanks scott!). The only part I've figured out is where to connect the spiral connector terminals on the connector D3. I don't know where these connect to on the other end, nor where I use the ECM repair terminal.

I've been using Vince87's DIY guide guide for this part, but unfortunately I really don't know what I'm doing when I get past the plug & play connectors!


This should help with installing the ECM Pin:

DIY - How to remove or insert a pin on the ECM Connector A21
teddyOntario, Canada · Dec 28, 2010#77
That's one more piece of the puzzle... Unfortunately I still don't know where the terminals from D3 connect go to, nor where the ECM connector connects from..

I will definitely be compiling this into a guide when this is done.
CTScottThread starterUSA, CT · Dec 28, 2010#78
Originally Posted by teddy ↑
That's one more piece of the puzzle... Unfortunately I still don't know where the terminals from D3 connect go to, nor where the ECM connector connects from..

I will definitely be compiling this into a guide when this is done.


OK - The ECM pin goes into position A21-pin 40, per the link above. The wire from there connects to pin 1 of D3 (where the blue wire is in the picture below). The second D3 pin goes where the brown wire is in pin 2 of D3. That wire simply gets tied to a chassis ground point (and bolt going into steel under the dash).




On the other side of D3 is the spiral cable (or clockspring as some call it). That is the wiring that goes into the steering wheel. The plug and play connector from the stalk connects the stalk to the two pins above in D3.

The final piece of the puzzle is the horn wire. The existing horn wire has to be moved into the new spiral cable connector in the same position that it was in in its existing connector.
CTScottThread starterUSA, CT · Dec 28, 2010#79
By the way, D3 is the white connector at the bottom left.
teddyOntario, Canada · Dec 28, 2010#80
I think I've got the steering wheel part done right, happy to be corrected.
Sorry about the quality of these pics, I got out to the car and found out the battery in my camera was dead.

D3 was the only part I was able to find, the rest I will find later when I've got my step dad with me. Much easier to do this with a second set of hands when I'm not feeling terribly confident.... and he is an electrical technician of sorts.
1228101535b.jpg1228101535a.jpg
CTScottThread starterUSA, CT · Dec 28, 2010#81
Steering wheel connections look good.
CB900F2Toronto · Jan 8, 2011#82
Scott..

I have the 2008 CND Sedan, and as we all know, the instrument cluster that came with the CND 2008 sedan doesnt have the Cruse indicator.

From your EPC, is there any information to which indicates a part# and possible year series of a cluster that has the cruise indicator and the same in all other features to the the one that came with the car?..

I am trying too see what options I may have in trying to get a CND cluster with the indicator

Thanks Scott!
CTScottThread starterUSA, CT · Jan 8, 2011#83
Originally Posted by CB900F2 ↑
Scott..

I have the 2008 CND Sedan, and as we all know, the instrument cluster that came with the CND 2008 sedan doesnt have the Cruse indicator.

From your EPC, is there any information to which indicates a part# and possible year series of a cluster that has the cruise indicator and the same in all other features to the the one that came with the car?..

I am trying too see what options I may have in trying to get a CND cluster with the indicator

Thanks Scott!
The EPC doesn't give the details on which cluster includes the indicator, but if you can find the VIN for a Yaris with one I can do a reverse lookup to figure out the part number(s).
frankmontrealMontréal · Jan 10, 2011#84
hi! same as teddy 06 canadian yaris, called the junk yard they got the stick with cable for 30$, so from what i understand the rest of the stuff from you scott?
CTScottThread starterUSA, CT · Jan 10, 2011#85
Originally Posted by frankmontreal ↑
hi! same as teddy 06 canadian yaris, called the junk yard they got the stick with cable for 30$, so from what i understand the rest of the stuff from you scott?
Nice price on the stalk with wire.

I do have the pins that you'll need to complete the stalk wiring. Here's the link to my thread, which has pictures of the pins, but you need the three pins (ECM connector pin and two pins for connector D3) to wire up your stalk:

FS: DIY Cruise Control Pin Kits
bairjoJan 15, 2011#86
Stalk 84632-34011 on ebay today for 19.95. 10 available. Do your search by typing yaris cruise control. If you type the part number it will not show up.
ibanezjeepguyMyrtle Beach, SC USA · Jan 15, 2011#87
haha, 15 to 30 days shipping..... I guess its worth the wait ?
I just scored a nice factory stereo off ebay recently, good find as well
bairjoJan 15, 2011#88
It's worth the wait for me as I am in the process of breaking in my new yaris. I'm trying to vary the speed during my 30 mile commute each way. Not a bad little break in drive each day. I have read that setting your speed with cruise and forgetting about during break in is the worst thing to do. So I can wait....
ibanezjeepguyMyrtle Beach, SC USA · Jan 15, 2011#89
the way engines are built today they can be broken in with less than a weeks worth of driving
bairjoJan 16, 2011#90
One week of driving how many miles? Based on your reply you and I agree the car needs a break in. Just how many miles is in question. I understand why you feel that one week is good enough. The tolerances of todays cars are much tighter due to improved capabilties of machining or grinding equipment. However, that is on paper and not what is always held and passed on the shop floor. Even with a 100% inspection process, marginal product will get passed. Therefore, I have chosen to go the time proven break in process for piece of mind. It doesn't cost me anything so why not do it?
Since this is a thread on cruise control we probably should look for a thread on break in peroid for any further discusion on that subject. In the mean time, I'll be waiting for my cruise control stalk to arrive.
ibanezjeepguyMyrtle Beach, SC USA · Jan 16, 2011#91
true that man, maybe a mod should wipe these last couple posts...
post back with how your stalk install goes and if you have any problems.
Buddy FanParma, OH · Jan 24, 2011#92
Went to the dealer to order the stalk wire and clutch switch and was told they changed the part number for the cc stalk wire to 84633-02020. Hope this helps anyone planning this DIY.
CTScottThread starterUSA, CT · Jan 24, 2011#93
Originally Posted by Buddy Fan ↑
Went to the dealer to order the stalk wire and clutch switch and was told they changed the part number for the cc stalk wire to 84633-02020. Hope this helps anyone planning this DIY.
Thanks for the heads-up. I updated the thread with that info and have confirmed it via the EPC.

What's the latest pricing on the stalk, wire, and clutch switch?
ibanezjeepguyMyrtle Beach, SC USA · Jan 24, 2011#94
same thing happened to me a couple months ago... the dealer can easily see the older numbers. even toyota parts zone or comparable sites list the new and old numbers I believe.
yarisbirdCypress, CA · Jan 25, 2011#95
I just completed the installation of cruise control in my 07 hatchback using the oem stalk that I purchased from e-bay and the cruise indicator module/light and wires/pins from CTScott. The cruise control works great.

Only problem is with the indicator light. It turns on for one second when the ignition switch is turned on, but when the cruise control is turn on there is no light. I installed it according to the instructions using splice tap connectors. All of the connections are tight.

CTScott, is there any diagnostic check that you recommend to determine why the light doesn't turn on when the cruise switch is pressed? I have a digital multimeter if that helps. Thanks for all your help.
CTScottThread starterUSA, CT · Jan 25, 2011#96
Originally Posted by yarisbird ↑
I just completed the installation of cruise control in my 07 hatchback using the oem stalk that I purchased from e-bay and the cruise indicator module/light and wires/pins from CTScott. The cruise control works great.

Only problem is with the indicator light. It turns on for one second when the ignition switch is turned on, but when the cruise control is turn on there is no light. I installed it according to the instructions using splice tap connectors. All of the connections are tight.

CTScott, is there any diagnostic check that you recommend to determine why the light doesn't turn on when the cruise switch is pressed? I have a digital multimeter if that helps. Thanks for all your help.
Just to verify:

The blue wire is connected to the wire that goes to the ECM pin and one of the wires going to the stalk?

The white wire is connected to ignition switched power?

The black wire is connected to ground?
yarisbirdCypress, CA · Jan 25, 2011#97
Yes.

The blue wire is spliced into the wire that runs from the ecm to the connector under the steering wheel. (pin #1)

The black wire is spliced to the wire that runs from this connector (pin#2) to ground.

The white wire is spliced to the pink wire on the connector under the ignition switch.
CTScottThread starterUSA, CT · Jan 25, 2011#98
Originally Posted by yarisbird ↑
Yes.

The blue wire is spliced into the wire that runs from the ecm to the connector under the steering wheel. (pin #1)

The black wire is spliced to the wire that runs from this connector (pin#2) to ground.

The white wire is spliced to the pink wire on the connector under the ignition switch.
OK. There is something wrong with the module. PM me you shipping address again, and I'll ship you a replacement.
Buddy FanParma, OH · Jan 25, 2011#99
I'll have to get you exact numbers, but it was in the range of $45 to $50 for both.
CTScottThread starterUSA, CT · Jan 27, 2011#100
Originally Posted by Yarisonline ↑
Hey, I suggest trying to find that part at www.yarisparts.com ,that's where I get my parts at warehouse price. Good luck :)
I was just curious as to what the going price is, as I picked up a couple recently for less than wholesale, that I can offer for $40 shipped.