Yarisworld Archive

DIY Cruise Control FAQ (2006-2010 Yaris)

416 posts · 835,665 views · page 3 of 9

Replies continued

bkndacnHavre de Grace, MD · Jan 27, 2011#101
@CTScott : Just wanted to thank you for this DIY and wanted to tell you that my cc worked perfectly all 4000 miles cross country and that I even was able to teach my mom how to use it! (a feat in itself) But Me and My right foot thank you!
bairjoJan 28, 2011#102
Originally Posted by Yarisonline ↑
Hey, I suggest trying to find that part at www.yarisparts.com ,that's where I get my parts at warehouse price. Good luck :)
I tried the websight but non the links worked for me when i clicked on any model year. Ill try again later.
CTScottThread starterUSA, CT · Jan 28, 2011#103
Originally Posted by bairjo ↑
I tried the websight but non the links worked for me when i clicked on any model year. Ill try again later.
I have a feeling that it's a spammer. The site seems to be just a dummy front page with sharesale links at the bottom.
teddyOntario, Canada · Jan 31, 2011#104
I finally finished getting my CC wired up, Canadian 2008 hatchback. Thanks to Scott and everyone else who's contributed.

I will post some pics of the work in the near future. Probably took me a good 4 hours in total because I really had no idea what I was doing, drilling a hole in side of the steering wheel, inserting the pins at the end of the spiral cable, etc.

Probably going to do this on my Mother-in-law's 2007 sedan since she also has the Rostra unit and can get it removed by the dealer for a full refund.
bairjoJan 31, 2011#105
Well i just installed my cruise control thanks to the DIY info on this thread. I video taped it step by step. Do you think anyone wants to see this? I think it would encourage even the novice mechanic to take this on.
CTScottThread starterUSA, CT · Jan 31, 2011#106
Originally Posted by bairjo ↑
Well i just installed my cruise control thanks to the DIY info on this thread. I video taped it step by step. Do you think anyone wants to see this? I think it would encourage even the novice mechanic to take this on.
Sure - Post up the video.
teddyOntario, Canada · Feb 4, 2011#107
You'll need to upload the video to another site like Youtube or Photobucket.
bairjoFeb 4, 2011#108
okay thanks.
CB900F2Toronto · Feb 5, 2011#109
Hey guys

Has anyone attempted to run a line from D3 to AD4 as described on pages 7 and 8..? AD4 looks fairly accessible from the photo, but I have not had the chance to check myself.

Thanks
CTScottThread starterUSA, CT · Feb 5, 2011#110
Originally Posted by CB900F2 ↑
Hey guys

Has anyone attempted to run a line from D3 to AD4 as described on pages 7 and 8..? AD4 looks fairly accessible from the photo, but I have not had the chance to check myself.

Thanks

AD4 is under the top of the dash. You have to remove the dash top to get to it. Also, the wire from the ECM to AD4 is only there in 2009 sedans and 2009+ Puerto Rico cars.
CB900F2Toronto · Feb 5, 2011#111
Hi Scott.. Maybe we Canuks are lucky in this case, my 08 Sedan has the wire at the ECM, and I can only assume it connected at AD4

I had to confirm and took apart the ECN connector and snapped a photo..
Like you indicated, it appears that there is no access to the AD4 connector from under the dash, but wonder why Toyota/Rostra would put out these instructions if it was not possible?

Maybe to mess with our Cruise Control crazy minds :p

Originally Posted by CTScott ↑
AD4 is under the top of the dash. You have to remove the dash top to get to it. Also, the wire from the ECM to AD4 is only there in 2009 sedans and 2009+ Puerto Rico cars.
IMG_6970.JPG
CTScottThread starterUSA, CT · Feb 5, 2011#112
Originally Posted by CB900F2 ↑
Hi Scott.. Maybe we Canuks are lucky in this case, my 08 Sedan has the wire at the ECM, and I can only assume it connected at AD4

I had to confirm and took apart the ECN connector and snapped a photo..
Like you indicated, it appears that there is no access to the AD4 connector from under the dash, but wonder why Toyota/Rostra would put out these instructions if it was not possible?

Maybe to mess with our Cruise Control crazy minds :p
You just need to train a rat to climb up there and plug the pin in for you.
CB900F2Toronto · Feb 6, 2011#113
Originally Posted by CTScott ↑
You just need to train a rat to climb up there and plug the pin in for you.
I think that should not be a problem, Toyota dealerships have many of those, I think they call them "Automotive Technicians" 🤘
CTScottThread starterUSA, CT · Feb 7, 2011#114
Originally Posted by bairjo ↑
I little constructive feedback on the video i posted a few posts back would be nice as i may consider doing more on future modifications/repairs. Anyone? 🤷
I thought you did an excellent job with it. Now, we just need one for the 2008 and older cars that require the ECM and steering column pins to be added.
CTScottThread starterUSA, CT · Feb 8, 2011#115
Originally Posted by CB900F2 ↑
Hey guys

Has anyone attempted to run a line from D3 to AD4 as described on pages 7 and 8..? AD4 looks fairly accessible from the photo, but I have not had the chance to check myself.

Thanks
Here is more detail on AD4:


Connector location under dash (the gray connector next to the blue and yellow connectors at the top left section of this picture):
Conn AD4 - Location2.jpg

More detail on the connector's location (this is the male side {which is on the bottom when in place in the car} of the junction connector that is part of the dash harness):
Conn AD4 - Location.jpg

This is how the male pin gets inserted into the connector:
Conn AD4 - Pin Insertion.jpg

Detail of the male pin:
Conn AD4 - Male Pin.jpg
frankmontrealMontréal · Feb 10, 2011#116
got everything installed bud it do not work!

so ran a cable from pin 40 of the ecm to pin 1 of d3

grounded from pin 2 of d3 to a bolt of the column


installed the stalk with the new wire

the horn works fine.

i suspect the ground but its minus 15 celcius in the driveway so i'll
check that out again tommorrow,

anything i should test for if it's not the ground wire,

im reading about that ad4 thiing do i miss something?

2006 canadian yaris HB automatic
teddyOntario, Canada · Feb 10, 2011#117
Originally Posted by frankmontreal ↑
got everything installed bud it do not work!

so ran a cable from pin 40 of the ecm to pin 1 of d3

grounded from pin 2 of d3 to a bolt of the column


installed the stalk with the new wire

the horn works fine.

i suspect the ground but its minus 15 celcius in the driveway so i'll
check that out again tommorrow,

anything i should test for if it's not the ground wire,

im reading about that ad4 thiing do i miss something?

2006 canadian yaris HB automatic
I don't know what to check, but I definitely did not have to run anything to AD4 that we've heard about. It was direct from D3 to the to the ECM connector A21. Ran the cable through the grommet in the passenger side, under the carpet and eventually up into the steering column. On D3 I wasn't paying attention which pin was ground and which was to the ECM but it worked on the first try so apparently I got it right.
CTScottThread starterUSA, CT · Feb 10, 2011#118
Originally Posted by frankmontreal ↑
got everything installed bud it do not work!

so ran a cable from pin 40 of the ecm to pin 1 of d3

grounded from pin 2 of d3 to a bolt of the column


installed the stalk with the new wire

the horn works fine.

i suspect the ground but its minus 15 celcius in the driveway so i'll
check that out again tommorrow,

anything i should test for if it's not the ground wire,

im reading about that ad4 thiing do i miss something?

2006 canadian yaris HB automatic

I assume you have an Automatic, since you don't mention installing the clutch switch?

AD4 is the middle connection point. Some years/configurations of the Yaris have the pin from ECM A21-40 to AD4, but then lack the wire from AD4 to D3. In your case, if you had to add A21-40, then AD4 is not of interest.

For testing, if you have a multimeter, I would start with measuring the voltage on pin 1 of D3 with the ignition on - It should measure 12V, indicating that the connection from D3 to the ECM is good.

Next, unplug D3, and with an ohm meter, measure the resistance between pins 1 and 2 on the column. It should measure as open, and then if you hold in the on/off button on the stalk it should go to a dead short.
frankmontrealMontréal · Feb 10, 2011#119
sounds good, i`m gonna try that tomorrow night thanks for the fast answers
frankmontrealMontréal · Feb 11, 2011#120
ok so changed so ground wire, it's now connected to d1 bolt under the kick panel,

i've tested the d3 with ohm meter seems fine

i've tried to test from the emc wire(the one that goes right to it on passenger side under the carpet)
to the ground with my volt meter and nothing

i'm gonna check out the pin 40 emc again i guess but it seemed fine

im a bit discouraged here lol
CTScottThread starterUSA, CT · Feb 11, 2011#121
Originally Posted by frankmontreal ↑
ok so changed so ground wire, it's now connected to d1 bolt under the kick panel,

i've tested the d3 with ohm meter seems fine

i've tried to test from the emc wire(the one that goes right to it on passenger side under the carpet)
to the ground with my volt meter and nothing

i'm gonna check out the pin 40 emc again i guess but it seemed fine

im a bit discouraged here lol
The lack of 12V from the ECM pin definitely points to an issue with the pin. When it is fully inserted the weather seal should be just about flush with the top of the connector.
frankmontrealMontréal · Feb 11, 2011#122
you're right, that was it it works! the pin was not fully inserted

thanks alot!
CTScottThread starterUSA, CT · Feb 11, 2011#123
Originally Posted by frankmontreal ↑
you're right, that was it it works! the pin was not fully inserted

thanks alot!
Excellent!
teddyOntario, Canada · Feb 11, 2011#124
Hey Scott, random question for you. Say one were to install cruise in a manual transmission without installing the clutch switch. What would happen if you tried to use the depressed the clutch pedal? Obviously the cruise wouldn't know to disengage...
CTScottThread starterUSA, CT · Feb 11, 2011#125
Originally Posted by teddy ↑
Hey Scott, random question for you. Say one were to install cruise in a manual transmission without installing the clutch switch. What would happen if you tried to use the depressed the clutch pedal? Obviously the cruise wouldn't know to disengage...
To be able to engage cruise, you at least have to jump the pins that the switch connects to. With that done, if you hit the clutch while in cruise, the engine would rev.
TapokataSacramento, CA · Feb 12, 2011#126
Just a note of thanks to CTScott! I installed this mod today in my 09 HB- I used the two button arrangment, mounting the NO switches in the blank remote mirror plate next to the dimmer switch, shown below Less than 20 bucks in parts (Digi-key minimum purchase), and I've got cruise control in the clown-car.

Picture lost · tapokata.smugmug.com

With an 87 mile commute each way to work, my leg thanks you, and I thank you. It really works. 🙇:

Now if I could just get the fog light installation sorted...
frankmontrealMontréal · Feb 15, 2011#127
made my first road trip with the cruise control, montreal-quebec city, thats about 150 miles, i was a bit disapointed the cruise stopped working after 100miles while i was on the highway, kinda weird, i stopped the car for a coffee and it still wasn't working, that's yesterday, today i took the car and the cruise was fine, i need to figure it out cuz i'm driving down to florida in april... any ideas ?
ibanezjeepguyMyrtle Beach, SC USA · Feb 15, 2011#128
should probably post this in its own topic thread with more details on which CC setup you are using, IE: stock / home-made / etc.......
CTScottThread starterUSA, CT · Feb 15, 2011#129
Originally Posted by frankmontreal ↑
made my first road trip with the cruise control, montreal-quebec city, thats about 150 miles, i was a bit disapointed the cruise stopped working after 100miles while i was on the highway, kinda weird, i stopped the car for a coffee and it still wasn't working, that's yesterday, today i took the car and the cruise was fine, i need to figure it out cuz i'm driving down to florida in april... any ideas ?
It's probably still the ECM pin. It may have gotten misshapen with plugging the connector in with the pin not fully inserted.
haydendfw · Feb 17, 2011#130
How do you guys recommend running the wire from the ECM to D3? I've got my car in pieces outside and I'm unsure what route to take. There's a rubber grommit thing that seems to house all the other wires going to the engine bay - should I poke a hole in that or what?
haydendfw · Feb 17, 2011#131
CTScott replied via PM:

Originally Posted by CTScott
Originally Posted by hayden
How do you recommend running the wire from the ECM to D3? I've got my car in pieces outside and I'm unsure what route to take. There's a rubber grommit thing that seems to house all the other wires going to the engine bay - should I poke a hole in that or what?
There are two ways you can go -

1.You can go down and slightly to the right from the ECM and go through the rubber grommet for the A/C drain hose. It enters the cabin just under the top left edge of the front passenger side carpet (along the hump).

2. You can follow the ECM cable bundle across the top of the engine bay and enter through the giant grommet behind the battery that comes out under the driver's side of the dash, near where the steering column pokes through the fire wall.

Either way, you poke through the grommet with a small screwdriver and then pass the wire through the poked hole.

The 1st way is definitely easier, as the second requires pulling the battery. With the first, you then feed the wire between the A/C system and the plastic of the center of the dash to get across to the steering column.
haydendfw · Feb 17, 2011#132
I also just want to say how awesome CTScott has been in helping me figure this out. I fancy myself rather technically inclined - I've done just about every sort of repair on a couple difference motorcycles I fixed up - but dear God this was a pain in the ass.

For anyone who has a 2007 auto with no power packages, let me sum up all the steps here (for an OEM install) because it was a freaking pain to figure this all out myself.

1. Get the OEM stalk (ebay or on these forums) and pin kit (CTScott sells the pin kit) and some extra 18-22AWG wire (radio shack or elsewhere). You'll need about 6 feet of the extra wire just to be safe. You're also going to need a way to make three connections between wires, either with soldering or with some other connector (I used the squeeze something kind).

2. Plug the ECM pin from your pin kit into your ECM. There's a guide for it here:
DIY - How to remove or insert a pin on the ECM Connector A21
Something the guide doesn't cover that I couldn't figure out is that once the big clunky cord of wires is unplugged from the ECM is how to move the white plastic bit so you can get the pin in. The big plastic housing around it got in the way and I couldn't figure out how to get it off without risking breaking it. I found that there's a little white tab on the inside of the connector where it attaches to the ECM. The tab is down a valley the middle and you can just stick something thin down there to slide it over. This is probably a bad description, but just keep looking at it until you see it.

I went into this project thinking the ECM was under the dash and I didn't need to worry about routing a wire to the engine bay. WRONG. The ECM is easily spotted if you pop the hood and look to the left of the engine on the firewall.

3. This wire has to be run to the D3 connector, which is under the steering wheel, and is ideally routed under the dash. There are two ways to do this (see above post) and I highly recommend taking option one. To clarify option one, you have to lift a bit of the carpet in the front passenger foot area to find the grommet he's talking about. The length of the pin kit wire isn't going to be long enough, so you're going to want to connect it to your 18-22AWG extra wire. My suggestion is to feed the extra wire from inside the cabin to the engine bay, and then make the connection (I used squeeze connector things, but soldering is ideal) inside the engine bay.

4. Before you can attach this wire to D3, you have a whole lot of plastic disassembly ahead of you. The ENTIRE top dash has to come off and this is no easy feat the first time you do it. The only reason I was able to figure it out was here:
Link to a thread or page that is not in the archive
Be sure to note my extra comment that was left out, where you also have to undo the cup holder screws. To clarify the first step, you're removing the plastic pillars that go up along the windshield (where you'd normally find side impact airbags in some cars).

5. If you managed to get the dash off, you're probably ready to give up on life, but you're done with all the hard parts. Route your wire that came in from the engine bay up across the mess of wires under your dash and bring it over to your steering wheel. You're now going to follow the first three steps of this tutorial:
DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag
to get access to the D3 connector. Use your two remaining wires from the pin kit, plug them into the connector (NOTE: YOU HAVE TO FIDDLE WITH THE MOVABLE PART ON THE CONNECTOR TO GET THE PINS IN). You're now going to take the wire from pin 2 and attach it to any ground point (I used the one on the driver side pillar) and attach the wire from pin 1 to the wire you dragged from the engine bay and across your dash. Congratulations, you're wired to use the OEM CC stalk! Have fun putting this shit all back together (especially if you realize you forgot to put a screw back in under the dash after its all together, like I did). I also had to fiddle with the stupid center air vent for about 10 minutes before I got the cover back on without screwing it up.

6. Follow this tutorial, ignoring the first two photos (which are for manual transmissions):
Link to a thread or page that is not in the archive
With any luck, you're now ready to go.


All in all this took me 4 hours NOT including step 6, which I still haven't done yet (too worn out and don't have a drill to make the hole right now). This also doesn't include the three or so hours I spent reading and trying to figure this all out before I started. A big reason it took so long was because I was sitting in my car while it was in pieces reading my laptop trying to figure out what to do. Figuring out the wiring between the engine bay and the dash was probably at least an hour of it. I don't think I could have actually ever gotten the wire through with option 2, which was the only way I could find as I was out there doing it myself. I finally gave up and asked CTScott for help and he replied quickly and saved my ass. If I knew it was this involved I don't think I would have bothered, but with any luck it'll work tomorrow once I get the stalk installed. It's gonna suck real bad if it turns out those squeeze connectors didn't work.

In retrospect, this project would have been a lot easier if I routed the wire through the front pillars and ceiling lining or something, because taking the dash off was by far the biggest pain and may have not been 100% needed.

Also forgive any typos, I'm extremely tired and half insane now.
CTScottThread starterUSA, CT · Feb 18, 2011#133
Wow - That sounds like it was indeed painful. You actually didn't need to take the dash apart to get to D3, nor to run the wire across. You can remove just the lower steering column cover to access D3. If you remove the lower passenger glove box, you can feed the wire between the A/C system and the center dash trim and across to the driver's side. On the driver's side, if you flip down the plastic access panel, under the steering wheel, you can grab the wire from the other side.

There are so many separate DIYs with bits and pieces in regards to the pre-09 cars that it is very difficult to sort through it all. I am still waiting for someone relatively local, with an 07 or 08, to take me up on the offer of helping them out with the install. That way I can put together a comprehensive DIY.
haydendfw · Feb 18, 2011#134
Well I guess I'm dumb.
CTScottThread starterUSA, CT · Feb 18, 2011#135
Originally Posted by hayden ↑
Well I guess I'm dumb.

Definitely not, since you got the job done.
haydendfw · Feb 19, 2011#136
Got the stalk installed today (after getting the hole position pretty wrong, it's now pretty giant) and it worked! Hooray!
mberasouth africa · Feb 22, 2011#137
Hi guys I just got my yaris - 2011 - 1.3 in south africa. - can I do this mod on her. ?
Thanx
CTScottThread starterUSA, CT · Feb 22, 2011#138
Originally Posted by mbera ↑
Hi guys I just got my yaris - 2011 - 1.3 in south africa. - can I do this mod on her. ?
Thanx
No. Only the US and Canada 1.5L models have cruise control functionality built into the ECM.
YarossJubail, KSA · Feb 24, 2011#139
sirs, just a stupid question...

if we really wanted CC in our yaris, but our ECM was not equipped:

1. can we swapped our ECM with those that have CC already programmed in it? --or --
2. can we use our existing ecm but with some modifications?

our yaris is drive-by-wire, so there must be some other way to do it...
CTScottThread starterUSA, CT · Feb 24, 2011#140
Originally Posted by Yaross ↑
sirs, just a stupid question...

if we really wanted CC in our yaris, but our ECM was not equipped:

1. can we swapped our ECM with those that have CC already programmed in it? --or --
2. can we use our existing ecm but with some modifications?

our yaris is drive-by-wire, so there must be some other way to do it...
Only the ECM for the 1.5L engine has the built in cruise control, so if your Yaris has the 1.5, then you could swap in a USDM ECM.

The other option is to use one of the aftermarket cruise control systems. There is one system from Europe for Toyotas and I believe that the Rostra system will work with non-US Yaris.
kimjoOshkosh WI · Feb 26, 2011#141
Originally Posted by ibanezjeepguy ↑
haha, 15 to 30 days shipping..... I guess its worth the wait ?
I just scored a nice factory stereo off ebay recently, good find as well
I got mine in 22 days looks good and the wires from ctscott
kimjoOshkosh WI · Feb 27, 2011#142
Well we just finished installing the cruise control. It took a total of 2 1/2 hours including the test drive. It probably would have taken less but we triple checked everything. Can't be too careful.

eBay stalk $30 with shipping
Wires from Scott with the correct ends $10 (but really priceless also)
Saving $360 and doing it ourselves. Priceless

Thanks to everyone here on YW for sharing all you learn.
DSpragueLittleton, Co · Mar 1, 2011#143
Ok, picked up my new 2010 Yaris sedan yesterday with no power package. What Toyota part #s do I need to install factory CC with the stalk on the column? I read through these 9 pages and now my head hurts and I feel confused! Any help would be great.
Thanks
Dan
CTScottThread starterUSA, CT · Mar 1, 2011#144
Originally Posted by DSprague ↑
Ok, picked up my new 2010 Yaris sedan yesterday with no power package. What Toyota part #s do I need to install factory CC with the stalk on the column? I read through these 9 pages and now my head hurts and I feel confused! Any help would be great.
Thanks
Dan
Dan,

For your 2010 you should just need the Stalk (84632-34011), stalk wire (84633-02020), and mounting screws(90159-50199 {quantity 2}). If you want the precut hole for the stalk, rather than drilling the plastic cover, you will also need the lower boss (45184-52130-B0).
CTScottThread starterUSA, CT · Mar 1, 2011#146
Originally Posted by ibanezjeepguy ↑
http://www.trdsparks.com/displaypart...&parts_id=2306
pretty cheap stalk & wire combo. for the screws just get some from hardware store I believe they're M5 x 0.8 , same as xbox 360 heatsink
Also, I have a couple of the stalks with the wire and the screws for $40 shipped, which is less than half of that price.
ibanezjeepguyMyrtle Beach, SC USA · Mar 1, 2011#147
how long have you had those? I could've used an awesome deal like that last year!
CTScottThread starterUSA, CT · Mar 1, 2011#148
Originally Posted by ibanezjeepguy ↑
how long have you had those? I could've used an awesome deal like that last year!
About two months ago a friend of mine got me a few at dealer cost.
DSpragueLittleton, Co · Mar 1, 2011#149
Originally Posted by CTScott ↑
Also, I have a couple of the stalks with the wire and the screws for $40 shipped, which is less than half of that price.
I'm in, how do I pay you?
Dan
CTScottThread starterUSA, CT · Mar 1, 2011#150
Originally Posted by DSprague ↑
I'm in, how do I pay you?
Dan
PM sent.