If that looks solid, work your way towards the stalk, verifying the connections along the way.Originally Posted by hayden ↑Reseated the pin, no luck. I'll try going out there and wiggling it while taking a reading to see if I can make it go to 0. Any other advice if that shows up fine though?
DIY Cruise Control FAQ (2006-2010 Yaris)
416 posts · 835,665 views · page 5 of 9
Replies continued
I'm trying to test the wire right at the stalk, but I think I'm maybe having trouble finding a ground for the negative pokey thing. Do you have suggestions of a ground available near the steering wheel?
I removed all my plastic connectors and just wrapped the ends of wires around each other, put a little solder, and duct taped it. I'm thinking maybe it's the D3 connector but wasn't able to remember how to "unclamp" it.
And it turns out, the extra wire I bought is this thick solid type (think barbed wire with rubber coating) rather than the typical frayed stuff you see in electronics - that doesn't matter does it?
I removed all my plastic connectors and just wrapped the ends of wires around each other, put a little solder, and duct taped it. I'm thinking maybe it's the D3 connector but wasn't able to remember how to "unclamp" it.
And it turns out, the extra wire I bought is this thick solid type (think barbed wire with rubber coating) rather than the typical frayed stuff you see in electronics - that doesn't matter does it?
Any bare metal under the dash will make a good ground.Originally Posted by hayden ↑I'm trying to test the wire right at the stalk, but I think I'm maybe having trouble finding a ground for the negative pokey thing. Do you have suggestions of a ground available near the steering wheel?
I removed all my plastic connectors and just wrapped the ends of wires around each other, put a little solder, and duct taped it. I'm thinking maybe it's the D3 connector but wasn't able to remember how to "unclamp" it.
And it turns out, the extra wire I bought is this thick solid type (think barbed wire with rubber coating) rather than the typical frayed stuff you see in electronics - that doesn't matter does it?
The only potential issue with solid instead of stranded wire is flexibility. Solid wire can't be flexed too much or it will break.
I think I'm giving up. I guess I'm a god damned retard because apparently I cannot even make the wires connect. I reran ALL of the wire again, and the connection right at the D3 connector will be fine for 5 minutes, then with changing nothing, the connection will break. I'll check it at the ECM, it's fine, and then check it again at D3 and magically it's working again after changing nothing. And now even when there's a connection right before the D3 connector, moving the CC stalk no longer causes any changes in voltages, meaning there's now also a problem with the D3 connector or something between the D3 and the stalk.Originally Posted by CTScott ↑Any bare metal under the dash will make a good ground.
The only potential issue with solid instead of stranded wire is flexibility. Solid wire can't be flexed too much or it will break.
Maybe I'll just put up a craigslist ad asking someone who isn't a retard to do it for me for $50 or something. Anyone in DFW want to make some easy money?
..anyone still selling the cheap OEM cruise control stalk & connector cable? for '09 yaris sedan?....I can only find the >$80 one's online, which is a bit over my budget!..any help appreciated!
I still have a bunch that I sell for $40 with the wire and the mounting screws. I will PM you my paypal info.Originally Posted by ejm ↑..anyone still selling the cheap OEM cruise control stalk & connector cable? for '09 yaris sedan?....I can only find the >$80 one's online, which is a bit over my budget!..any help appreciated!
Scott,Originally Posted by CTScott ↑I still have a bunch that I sell for $40 with the wire and the mounting screws. I will PM you my paypal info.
Finished installing mine yesterday, it took 1 hour and works like a charm, thanks for the fast shipping, extra pins and the stalk was brand new. 👍
One thing else I forgot to add was that the stalk already had the Horn wire in it, no need to rewire per the DIY notes available in this site.
Exactly - I actually add the horn wire before I ship them to make it easier for people to install them.Originally Posted by PROX4x4 ↑Scott,
Finished installing mine yesterday, it took 1 hour and works like a charm, thanks for the fast shipping, extra pins and the stalk was brand new. 👍
One thing else I forgot to add was that the stalk already had the Horn wire in it, no need to rewire per the DIY notes available in this site.
Got my stick today, ( fast shipping!!) installed it in 1/2 hr!!
Thanks Scott!!
Thanks Scott!!
CTScott -
Have only been reading (a lot) since I got my '11 3Dr last week but took a quick interest in this thread. It's probably +47 or so, but thank you immensely for putting so much great info together!
Do you still have any of the CC clutch switches that will work on my ride?
TIA
Have only been reading (a lot) since I got my '11 3Dr last week but took a quick interest in this thread. It's probably +47 or so, but thank you immensely for putting so much great info together!
Do you still have any of the CC clutch switches that will work on my ride?
TIA
Originally Posted by 2mtech ↑CTScott -
Have only been reading (a lot) since I got my '11 3Dr last week but took a quick interest in this thread. It's probably +47 or so, but thank you immensely for putting so much great info together!
Do you still have any of the CC clutch switches that will work on my ride?
TIA
Yes. I try to keep all of the parts on hand, so I have stalks, clutch switches, and the pins required for pre-09 cars.
Cool. If you would PM me your PayPal addy I'll be more than glad to make your parts inventory lighter and your balance heavier 😉Originally Posted by CTScott ↑Yes. I try to keep all of the parts on hand, so I have stalks, clutch switches, and the pins required for pre-09 cars.
Scott -
In looking to incorporate all four CC functions into one switch, it occurred to me that the power rearview mirror adjust switch is a four-way, MOM-MOM-MOM-MOM-OFF switch. What do you think of the possibility of using that switch for the CC functions? Do you have a spec of that switch (since you have everything else 😉)? I don't have power mirrors so acquiring and using that switch would be ideal if it would work. I have no desire to mess with the airbag/steering wheel to install the stalk and haven't been able to locate a suitable aftermarket 4-way part.
As always, your input is eagerly awaited 🙇
In looking to incorporate all four CC functions into one switch, it occurred to me that the power rearview mirror adjust switch is a four-way, MOM-MOM-MOM-MOM-OFF switch. What do you think of the possibility of using that switch for the CC functions? Do you have a spec of that switch (since you have everything else 😉)? I don't have power mirrors so acquiring and using that switch would be ideal if it would work. I have no desire to mess with the airbag/steering wheel to install the stalk and haven't been able to locate a suitable aftermarket 4-way part.
As always, your input is eagerly awaited 🙇
Originally Posted by 2mtech ↑Scott -
In looking to incorporate all four CC functions into one switch, it occurred to me that the power rearview mirror adjust switch is a four-way, MOM-MOM-MOM-MOM-OFF switch. What do you think of the possibility of using that switch for the CC functions? Do you have a spec of that switch (since you have everything else 😉)? I don't have power mirrors so acquiring and using that switch would be ideal if it would work. I have no desire to mess with the airbag/steering wheel to install the stalk and haven't been able to locate a suitable aftermarket 4-way part.
As always, your input is eagerly awaited 🙇
The power mirror switch has an internal PCB that handles switching the four functions between the two sides. You would have to gut one to see if that switch is actually usable. Someone else on here found a nice little joystick type switch.
By the way, those power mirror switches typically sell for more than my $40 price tag for the OEM stalk.
That would figure...I always try to do things in the most expensive way possible 😉Originally Posted by CTScott ↑The power mirror switch has an internal PCB that handles switching the four functions between the two sides. You would have to gut one to see if that switch is actually usable. Someone else on here found a nice little joystick type switch.
By the way, those power mirror switches typically sell for more than my $40 price tag for the OEM stalk.
I have the Digikey switches now, may just settle for them.
Thanks for the response!
Did the mod today, using the joystick switch from Allied Electric 127.0.0.1 used (only with the bat handle instead of the arrow button), and the clutch switch and resistors from Scott.
http://www.alliedelec.com/search/pro...px?SKU=9480343
I installed it where the outside rearview mirror adjust switch would've been if equipped. It's easy to reach, and running the wires from that point was simple.

Everything worked perfectly! Thanks so much again, Scott! 🤘
http://www.alliedelec.com/search/pro...px?SKU=9480343
I installed it where the outside rearview mirror adjust switch would've been if equipped. It's easy to reach, and running the wires from that point was simple.

Everything worked perfectly! Thanks so much again, Scott! 🤘
Thanks guys! Just did it this morning after getting the parts from Scott. Works perfect on my 09 hatch! I used the oem lower steering wheel cover from the dealer, here's what the hole looks like:


Hi. I'd like to install cruise control on my new Yaris (new to me) but I'm a bit concerned about messing up the safety systems, i.e. airbags. I went to my local library and looked at a copy of Chilton's service manual for late model Toyotas and they recommend using [OEM?] scanning/diagnostic tools to check for system errors anytime an air bag has been removed and then re-installed on Toyotas with OCS prior to reconnecting the battery. I don't have access to such equipment but I like to be sure everything is still working when I put it back together. What are the risks of not following this step or is Chilton just being hyper sensitive? Doesn't the Yaris have a built in diagnostic function with connection to the instrument indicator light? The Chilton manual, part of a hard cover phone book thick series covering Asian cars, appeared to be written for repair shops. I'm fine with doing the mechanical and electrical work for the CC thanks to all the effort people have put in on this forum but I'm a little spooked at the air bags and the related systems. Any help would be appreciated. Thanks
MN:-)Yaris
MN:-)Yaris
If there are any issues with the SRS, the airbag light will illuminate on the dash, so as long as you don't have the light on when you are done, all is well. If the light was on, there is a method (posted in another thread) to make the SRS ECU flash the airbag light in a pattern to tell you what the error is.Originally Posted by MN:-)Yaris ↑Hi. I'd like to install cruise control on my new Yaris (new to me) but I'm a bit concerned about messing up the safety systems, i.e. airbags. I went to my local library and looked at a copy of Chilton's service manual for late model Toyotas and they recommend using [OEM?] scanning/diagnostic tools to check for system errors anytime an air bag has been removed and then re-installed on Toyotas with OCS prior to reconnecting the battery. I don't have access to such equipment but I like to be sure everything is still working when I put it back together. What are the risks of not following this step or is Chilton just being hyper sensitive? Doesn't the Yaris have a built in diagnostic function with connection to the instrument indicator light? The Chilton manual, part of a hard cover phone book thick series covering Asian cars, appeared to be written for repair shops. I'm fine with doing the mechanical and electrical work for the CC thanks to all the effort people have put in on this forum but I'm a little spooked at the air bags and the related systems. Any help would be appreciated. Thanks
MN:-)Yaris
Well, I know it's been a while since I ask for your help, a 4 hour drive remind me I need this mod. Check this out please.Originally Posted by CTScott ↑Mexican Yaris get a different ECM than US and Canadian ones, so you would definitely have to test it to see. The place to start is to measure the voltage on the ECM pin 40, with the ignition in the on position. If you see 12 Volts on that pin, then there's a good chance that it will work.
If you shine a flashlight around on your instrument cluster, do you see the two icons for cruise control?
My instrument cluster has the two icons for CC, my ECM part number is 89661-52G71, and I have a reason to believe that mexican and canadian yaris use the same specs because there's a sticker on my door with a canadian logo.
The canadian sticker surprised me, apparently all mexican Yaris got it, a friend of mine has a sedan and the same sticker is there.

What do you think? can this be posible?
If that is correct and I have the canadian version I would like to buy one of your cc kits you sell and give this a shot.
Thanks for the help.
Originally Posted by carlosgil5 ↑Well, I know it's been a while since I ask for your help, a 4 hour drive remind me I need this mod. Check this out please.
My instrument cluster has the two icons for CC, my ECM part number is 89661-52G71, and I have a reason to believe that mexican and canadian yaris use the same specs because there's a sticker on my door with a canadian logo.
The canadian sticker surprised me, apparently all mexican Yaris got it, a friend of mine has a sedan and the same sticker is there.
What do you think? can this be posible?
If that is correct and I have the canadian version I would like to buy one of your cc kits you sell and give this a shot.
Thanks for the help.
I just ran your VIN through the EPC and your car is actually a Canada spec, not Mexico spec Yaris, so cruise will definitely work for you. I suspect that even for Mexico Spec cars that it will work as well.
🎉Originally Posted by CTScott ↑I just ran your VIN through the EPC and your car is actually a Canada spec, not Mexico spec Yaris, so cruise will definitely work for you. I suspect that even for Mexico Spec cars that it will work as well.
thanks for the quick reply.
are you still selling the cheap OEM cruise control stalk & connector cable?
I have a US based shipping address in Nogales, Arizona
Yes. I still have the Stalks with CC wire and mounting screws for $40, as well as the pins needed for 06-08. Theoretically your 2010 AT only needs the stalk, since the US and Canadian 09+ Yaris have the wiring in place, but you may want to take a peek at the ECM connector and the spiral cable connector to be sure.Originally Posted by carlosgil5 ↑🎉
thanks for the quick reply.
are you still selling the cheap OEM cruise control stalk & connector cable?
I have a US based shipping address in Nogales, Arizona
Please PM me your info.Originally Posted by CTScott ↑Yes. I still have the Stalks with CC wire and mounting screws for $40, as well as the pins needed for 06-08. Theoretically your 2010 AT only needs the stalk, since the US and Canadian 09+ Yaris have the wiring in place, but you may want to take a peek at the ECM connector and the spiral cable connector to be sure.
Can't wait to do this, If the wiring is already in place a friend of mine with a 08' sedan can use the extra wire.
Thanks for the help.
thanks for the info, but I think am gonna' drill. I'll be very careful.Originally Posted by ZeeGrandChamp ↑Did the CC upgrade on my 2010 USDM 3-Door... as easily as changing a shift knob. CTScott's kit is great and the updated part number for the cover is:
45184-52130-B0 and the list price is about $32.00
Well, am in trouble, I picked up the package, thanks for the kit, everything came in time and as expected.Originally Posted by carlosgil5 ↑Please PM me your info.
Can't wait to do this, If the wiring is already in place a friend of mine with a 08' sedan can use the extra wire.
Thanks for the help.
Drilled the cover, installed the stalk with the wire, did a road test and it's not working.
I definitely need help here guys.
What do you think, the 06-08 method?
Looks like this is going to be a learning experience for the people with Yaris bought in Mexico.
Originally Posted by carlosgil5 ↑Well, am in trouble, I picked up the package, thanks for the kit, everything came in time and as expected.
Drilled the cover, installed the stalk with the wire, did a road test and it's not working.
I definitely need help here guys.
What do you think, the 06-08 method?
Looks like this is going to be a learning experience for the people with Yaris bought in Mexico.
Can you take a measurement on the wire that goes to the ECM pin. With the ignition on and none of the stalk switches pressed, it should read +12V.
I could not get any measurement I have one of those little harness plugs in the hole where pin 40 would be.Originally Posted by CTScott ↑Can you take a measurement on the wire that goes to the ECM pin. With the ignition on and none of the stalk switches pressed, it should read +12V.
This are the connections under my steering wheel.
there's no blue and no brown wire.

This is my cluster showing the cc icons.

So I have to run the wire from which hole in the connector?
What else do I have to do, I already drilled the cover, plugged the stalk wire and bolted the OEM stalk.
I was really hoping my '10 AT had all the wires in place. Not at all.
So, you definitely need to add the connector D3 pins. The other question is if the ECM connector A21, pin 40 is present? On Puerto Rico spec cars, it is, but the D3 pins are not.Originally Posted by carlosgil5 ↑I could not get any measurement I have one of those little harness plugs in the hole where pin 40 would be.
This are the connections under my steering wheel.
there's no blue and no brown wire.
This is my cluster showing the cc icons.
So I have to run the wire from which hole in the connector?
What else do I have to do, I already drilled the cover, plugged the stalk wire and bolted the OEM stalk.
I was really hoping my '10 AT had all the wires in place. Not at all.
Am getting a little nervous about this, I unplugged the ECM connector A21, looked at the pin 40, small pin by the way, and looks like there´s nothing there, just the empty space, It was late and dark, of course I´ll double check at lunch time.Originally Posted by CTScott ↑So, you definitely need to add the connector D3 pins. The other question is if the ECM connector A21, pin 40 is present? On Puerto Rico spec cars, it is, but the D3 pins are not.
Now my concern is with my ECM, in theory I have the one used in the canadian Yaris (89661-52G71), but, what if there´s nothing on my ECM to receive the wire in the ECM connector A21 pin 40? would that mean I have the cruiseless euro type of ECM (nooo please)?
Oh boy am in panic.
89661-52G71 is a US/Canada spec ECM, so I am sure that you are OK. I should have made you check the ECM and connector D3 pins before I sent you the stalk.Originally Posted by carlosgil5 ↑Am getting a little nervous about this, I unplugged the ECM connector A21, looked at the pin 40, small pin by the way, and looks like there´s nothing there, just the empty space, It was late and dark, of course I´ll double check at lunch time.
Now my concern is with my ECM, in theory I have the one used in the canadian Yaris (89661-52G71), but, what if there´s nothing on my ECM to receive the wire in the ECM connector A21 pin 40? would that mean I have the cruiseless euro type of ECM (nooo please)?
Oh boy am in panic.
Hey CT you have been of great help, definitely my bad, since I have a ´10 I tought I had the wires in place and I was lazy to unbolt stuff and take a look.Originally Posted by CTScott ↑89661-52G71 is a US/Canada spec ECM, so I am sure that you are OK. I should have made you check the ECM and connector D3 pins before I sent you the stalk.
Ok, so my next step would be Vince87´s method right?
I already downloaded the PDF and read the entire thread.
wire from AD3 to ECM connector A21 pin 40 right?
Correct - Wire from A21-40 to D3 and D3 to ground. I can mail you the pins (ECM pin - $5, D3 Pins - $5). USPS to Mexico is the same as to Canada, so there would be no extra charge for me to ship them to you directly (rather than to your US address).Originally Posted by carlosgil5 ↑Hey CT you have been of great help, definitely my bad, since I have a ´10 I tought I had the wires in place and I was lazy to unbolt stuff and take a look.
Ok, so my next step would be Vince87´s method right?
I already downloaded the PDF and read the entire thread.
wire from AD3 to ECM connector A21 pin 40 right?
Wow, sounds great.Originally Posted by CTScott ↑Correct - Wire from A21-40 to D3 and D3 to ground. I can mail you the pins (ECM pin - $5, D3 Pins - $5). USPS to Mexico is the same as to Canada, so there would be no extra charge for me to ship them to you directly (rather than to your US address).
Do you know if USPS offers a faster shipping speed?, I am willing to pay a little more for a faster shipping and get this done.
Priority mail (6-10 business days) would be $13 more and Express mail (3-5 business days) would be $30 more.Originally Posted by carlosgil5 ↑Wow, sounds great.
Do you know if USPS offers a faster shipping speed?, I am willing to pay a little more for a faster shipping and get this done.
Ok, I think 3-5 bussiness days are too many days (expensive too), I am going to buy some 20-24 AWG wires and try to make the connection myself. Are these wires made from many thin wires or 1 thick one.Originally Posted by CTScott ↑Priority mail (6-10 business days) would be $13 more and Express mail (3-5 business days) would be $30 more.
If I can´t make it work, I´ll order them from you.
Sorry for so many questions I do not have electronic experience in cars.
I am very grateful, Thank you.
For testing purposes, stranded wire should work. You will probably not find it to be reliable for continued use though, without using connector pins.Originally Posted by carlosgil5 ↑Ok, I think 3-5 bussiness days are too many days (expensive too), I am going to buy some 20-24 AWG wires and try to make the connection myself. Are these wires made from many thin wires or 1 thick one.
If I can´t make it work, I´ll order them from you.
Sorry for so many questions I do not have electronic experience in cars.
I am very grateful, Thank you.
PM sent.Originally Posted by CTScott ↑For testing purposes, stranded wire should work. You will probably not find it to be reliable for continued use though, without using connector pins.
After picking up the envelope you sent me, today my quest for CC continues.Originally Posted by carlosgil5 ↑PM sent.

It is clear for me that the lengthiest wire is the one that goes to the ECM (ECM pin 40-D3 connector).
One of the two short wires you sent me is for ground and there's another one that I don't know what it is for.
It's not been clear to me on vince87's DIY pdf all things related to D3 connector, One wire to the ECM, but about the other two, where do I plug the wires that connect in D3 ( the other end of the wires), if one is ground, what about the other. The small one that is not ground go from where to where?
Sorry if am asking dumb questions I just want to do this right.
Originally Posted by carlosgil5 ↑After picking up the envelope you sent me, today my quest for CC continues.
It is clear for me that the lengthiest wire is the one that goes to the ECM (ECM pin 40-D3 connector).
One of the two short wires you sent me is for ground and there's another one that I don't know what it is for.
It's not been clear to me on vince87's DIY pdf all things related to D3 connector, One wire to the ECM, but about the other two, where do I plug the wires that connect in D3 ( the other end of the wires), if one is ground, what about the other. The small one that is not ground go from where to where?
Sorry if am asking dumb questions I just want to do this right.
Rather than the Vince DIY, look at my DIY (link below), which is a bit more complete. Basically, you will connect the larger pin to the ECM, run a wire from it to the column area, stick the other two pins in the appropriate spaces in the spiral cable connector D3 (under the column), connect one to the wire to the ECM and the other to ground.
DIY: 2006-2011 Yaris OEM Cruise Control Complete Installation
I made the connections as per the images below.
Pin 40 fully seated at correct location.

Connection at D3 connector.

sadly no cruise, checked for voltage at the wire before reaching the A21 connector with the ignition switch in the ON position and the meter shows 0.00, no power at all.
Am sure the terminals are fully seated because clicked in to place, after unlatching the locking mechanisms.
Your DIY was very helpful, it is a very complete guide.
On the D3 connector pin #2 went to a bolt (ground), pin#1 was spliced to the yellow wire coming from the ECM connector.
how can I continue to troubleshoot my installation.
Pin 40 fully seated at correct location.

Connection at D3 connector.

sadly no cruise, checked for voltage at the wire before reaching the A21 connector with the ignition switch in the ON position and the meter shows 0.00, no power at all.
Am sure the terminals are fully seated because clicked in to place, after unlatching the locking mechanisms.
Your DIY was very helpful, it is a very complete guide.
On the D3 connector pin #2 went to a bolt (ground), pin#1 was spliced to the yellow wire coming from the ECM connector.
how can I continue to troubleshoot my installation.
The no voltage on the A21 pin is definitely the issue. Are you absolutely sure that you are in the correct position on the ECM connector?
I unplugged the A21 connector and took a picture to show you the spot I placed the terminal (pin 40 I think), can you confirm if I plugged it in the right place? Note: this picture was rotated 180 degrees.Originally Posted by CTScott ↑The no voltage on the A21 pin is definitely the issue. Are you absolutely sure that you are in the correct position on the ECM connector?

I also took a picture of the ECM pins, I could not see anything wrong as all the ECM pins where there. This picture was not rotated.

When I tested the wire for voltage, the connector was fully seated at the ECM and right where we can see the wires in the harness I poked the pin 40 wire and got nothing.
Also did a road test and confirmed it was not working.
If I see correctly, it is the one round hole, which is the correct location.
🙇Thank you much for the info on the cc,i did the 2 switch mod last sat,works pro,thanks again,CTScott,my total cost was $7.00.ever up my way,beers are on me.👍😎
what's the difference between 84632-08021 and 84632-34011?
I don't believe that there is any real difference. 84632-08021 is listed as a direct replacement for 84632-34011.Originally Posted by thestranger ↑what's the difference between 84632-08021 and 84632-34011?
Hi,
This is my first post. I recently bought a 2008 Yaris Liftback. It's a 5-speed. I would have preferred for my next vehicle to have already had cruise control installed, but the circumstances didn't allow it. I am now considering CTScott's OEM cruise control method. I have read over this thread more than once and feel I can do this. I am only apprehensive about one thing. Since I have the 5-speed, I have to tap into the wires in the under-hood fuse box for the clutch cancel. This requires splicing into two of the wires (white and blue). CTScott's instructions suggest a tap splice. I was hoping to get around to "Cutting" or altering of the existing wire. Has anyone used anything different like connecting them using a pin of some sort in the wire hole? I know my fears are irrational, but cutting into those little wires makes me nervous. Any help is appreciated.
This is my first post. I recently bought a 2008 Yaris Liftback. It's a 5-speed. I would have preferred for my next vehicle to have already had cruise control installed, but the circumstances didn't allow it. I am now considering CTScott's OEM cruise control method. I have read over this thread more than once and feel I can do this. I am only apprehensive about one thing. Since I have the 5-speed, I have to tap into the wires in the under-hood fuse box for the clutch cancel. This requires splicing into two of the wires (white and blue). CTScott's instructions suggest a tap splice. I was hoping to get around to "Cutting" or altering of the existing wire. Has anyone used anything different like connecting them using a pin of some sort in the wire hole? I know my fears are irrational, but cutting into those little wires makes me nervous. Any help is appreciated.
I may actually have some male and female pins for the under-hood connector, which would allow you to make the connection without splicing.Originally Posted by Nicfin ↑Hi,
This is my first post. I recently bought a 2008 Yaris Liftback. It's a 5-speed. I would have preferred for my next vehicle to have already had cruise control installed, but the circumstances didn't allow it. I am now considering CTScott's OEM cruise control method. I have read over this thread more than once and feel I can do this. I am only apprehensive about one thing. Since I have the 5-speed, I have to tap into the wires in the under-hood fuse box for the clutch cancel. This requires splicing into two of the wires (white and blue). CTScott's instructions suggest a tap splice. I was hoping to get around to "Cutting" or altering of the existing wire. Has anyone used anything different like connecting them using a pin of some sort in the wire hole? I know my fears are irrational, but cutting into those little wires makes me nervous. Any help is appreciated.
That would be great! I am not an electrician, but that is sort of what I had in mind. I would gladly pay you for them and any of the other supplies if you were willing. I have looked up some of the parts, but have not made any purchases yet. That makes me feel better about attempting this. Gotta go.Originally Posted by CTScott ↑I may actually have some male and female pins for the under-hood connector, which would allow you to make the connection without splicing.
Thanks