Yarisworld Archive

DIY Cruise Control FAQ (2006-2010 Yaris)

416 posts · 835,665 views · page 4 of 9

Replies continued

CTScottThread starterUSA, CT · Mar 9, 2011#151
Originally Posted by cicici00 ↑
I have been really busy and did not have any chance to install my cruise control since I bought my OEM stalk from ebay (like months ago). I finally find a weekend to do this thing. I just want to make sure I get the set-up right before I break into my car.

I have a 2008 LB Yaris.

1. I first cut off the red+black wire clip at the end of the stalk

2. I see the "Spiral Connector Repair Terminals" in the parts requirement. I wonder if I really need it, if I treat the stalk = diy switch/button. Can I hook it up like in Fig. 1?


3. I think I will get "ECM repair terminal" for Pin 40. I know CTScott sells them. Since I finally find a free weekend to do it, I need that part sooner. So, I wonder if I can buy that from Toyota Dealership and get it on the same day? Or can I just get one from the junk yard? Or if Advanced Auto / Auto zone / radioshack sell them?? I am just afraid if I don't do it this weekend, it will be months after I can do it again.

4. I thought about just insert the wire into Pin 40. But, I am scared it will not be secured. How far do I need to insert the wire into the A21 ECM? Does the ECM terminal has some clip to hold all the wires in place? Anyone here did it without the "repair pin"??

Thanks again for all the help!! 🙇



1/2. You don't really want to clip the connector. If you are planning on mounting the stalk in the steering wheel, then it needs to go through the spiral cable.

3. If you want to use the pins, I can ship them today via priority mail for $5 more (bringing the total to $15 for the three pins), so you would have them in hand before the weekend. I believe that the dealer price on them is $12 each, so you would still be saving quite a bit, and I don't think that dealers typically stock them.

4. People have done it this way, but it does not always make good connection and is not sealed, so it will allow moisture to enter the connector.
CTScottThread starterUSA, CT · Mar 14, 2011#152
Originally Posted by wasserburgandy ↑
hi guys, i am from China, I own an Yaris made by Toyota China. Does anyone here know if the China version Yaris can install the cruise control or not? People here say the ECU doesn't support. tks
I don't have any of the wiring diagrams or manuals for the Chinese Yaris, but as far as I know, only the US/Canada 1.5L Yaris ECMs have it built in.
CTScottThread starterUSA, CT · Mar 14, 2011#153
Originally Posted by wasserburgandy ↑

BTW, do you have any file that records installing the CC by using original Toyota parts stalk& wire in detail with pics?? tks.
Look at the first page of this thread for links that show the installation of the OEM cruise stalk. From your pictures, you don't have the 1NZ-FE engine, which as far as I know, is the only one which has the ECM preprogrammed for cruise control.
CB900F2Toronto · Mar 18, 2011#154
Scott.. Would you happen to have a photo the the top half of AD4 connector as I got the connector off the white mount, but since it is a bit tight, I am having a hard time trying to find the latch to unhook the two halfs?..

Thanks Scott!


Originally Posted by CTScott ↑
Here is more detail on AD4:


Connector location under dash (the gray connector next to the blue and yellow connectors at the top left section of this picture):
Attachment 39851

More detail on the connector's location (this is the male side {which is on the bottom when in place in the car} of the junction connector that is part of the dash harness):
Attachment 39848

This is how the male pin gets inserted into the connector:
Attachment 39849

Detail of the male pin:
Attachment 39850
CTScottThread starterUSA, CT · Mar 18, 2011#155
Originally Posted by CB900F2 ↑
Scott.. Would you happen to have a photo the the top half of AD4 connector as I got the connector off the white mount, but since it is a bit tight, I am having a hard time trying to find the latch to unhook the two halfs?..

Thanks Scott!
AD4 - From Top.jpg

AD4 - Unlatched.jpg
CB900F2Toronto · Mar 19, 2011#156
Thanks Scott!
CTScottThread starterUSA, CT · Mar 19, 2011#157
Originally Posted by cdu ↑
I'm so confused...lol! I've gone through so many threads and am not sure where to start! I first came upon this video: http://www.youtube.com/watch?v=bWPXFYeLJj0

He makes it looks so easy but then I realized, after spending time on two threads here, that he doesn't touch on any of the engine work that also needs to be done.

I have an 07 Sedan/Automatic and live in Canada.

I know tons of people have asked this question and hate to do this to you guys but...what parts do I need for MY car?

Any help would be much appreciated!
That's why I just put this together. This is the detailed soup to nuts instructions for all aspects of installing OEM cruise control on any Yaris from 2006-2011:

DIY: 2006-2011 Yaris OEM Cruise Control Complete Installation
CB900F2Toronto · Mar 21, 2011#158
Installed the CC on my CND version 2008 Sedan and all went well, I want to give big thanks to every one and especially Scott for all of his great help!

I installed the OEM CC stalk and ran the CC signal line from D3 to AD4, getting to AD4 was not too bad, just trying to work in the small area under the dash was the only challenge. Grounded the GND line from D3 was no issue.

I recommend the up grade to anyone needing CC

Thanks again to Scott for all his great help and supply of connectors.
AetreNorthern Virginia · Mar 28, 2011#159
Hi, all. Newbie with a 2009 3dr liftback automatic and the dumb question of the day:

What parts of this cruise control installation, if any, would void the warranty?
ibanezjeepguyMyrtle Beach, SC USA · Mar 28, 2011#160
none...
AetreNorthern Virginia · Mar 29, 2011#161
Sweet, thanks.
ibanezjeepguyMyrtle Beach, SC USA · Mar 29, 2011#162
as long as you're adding toyota OE parts everything should be fine.... its when you start adding in your own home-brew stuff that things become grey
MidnightsunMontreal, Canada · Apr 21, 2011#163
Originally Posted by CTScott ↑
Also, I have a couple of the stalks with the wire and the screws for $40 shipped, which is less than half of that price.
Hey CTScott, I have been trying to get a hold of you as I would like to purchase this from you. Can you PM me please. Thanks.
CTScottThread starterUSA, CT · Apr 23, 2011#164
Originally Posted by Midnightsun ↑
Hey CTScott, I have been trying to get a hold of you as I would like to purchase this from you. Can you PM me please. Thanks.
Sorry, I've been out of the country SCUBA diving for a week. I just hit you back by PM.
teddyOntario, Canada · Apr 24, 2011#165
Can somebody with the OEM cruise & steering wheel cover please post a picture showing the hole where the stalk comes out? Doesn't even have to be a DIY job, even with it installed from the factory.

I'm thinking about picking up an OEM steering wheel cover with the pre-cut hole. The one I drilled is a bit of an eye sore.. much larger than it needed to be because I drilled it in the wrong spot and had to adjust a few times.

thanks
haydendfw · Apr 24, 2011#166
Well I had a pretty scary experience tonight. I installed cruise control with the OEM stalk a few (I think) months ago and it's worked flawlessly up until tonight. It was humid and raining which I think may have caused it?

Anyway, at first CC wouldn't work at all. I fiddled with the stalk a few times on the drive and eventually it turned on. All was well for a couple minutes, until I starting hearing the engine rev and noticed I was going 90MPH (I set it to about 65). It was like the cruise control stalk was stuck in the up position (it wasn't). It did this several times while also cutting out and not working several times during my 30 minute trip. I was obviously watching it very closely after it happened the first time.

Not sure what the cause could be. I'm guessing a loose wire or something? Anyway, extremely unsafe either way and a big notice to anyone out there to be sure to know what they're doing.
CTScottThread starterUSA, CT · Apr 24, 2011#167
Originally Posted by hayden ↑
Well I had a pretty scary experience tonight. I installed cruise control with the OEM stalk a few (I think) months ago and it's worked flawlessly up until tonight. It was humid and raining which I think may have caused it?

Anyway, at first CC wouldn't work at all. I fiddled with the stalk a few times on the drive and eventually it turned on. All was well for a couple minutes, until I starting hearing the engine rev and noticed I was going 90MPH (I set it to about 65). It was like the cruise control stalk was stuck in the up position (it wasn't). It did this several times while also cutting out and not working several times during my 30 minute trip. I was obviously watching it very closely after it happened the first time.

Not sure what the cause could be. I'm guessing a loose wire or something? Anyway, extremely unsafe either way and a big notice to anyone out there to be sure to know what they're doing.

If you have access to a multimeter, with the ignition off, measure the resistance between the two stalk wires with nothing pressed and then again with each switch activated.
haydendfw · Apr 24, 2011#168
I'll give it a try tomorrow and let you know, thanks.
CB900F2Toronto · Apr 25, 2011#169
Teddy and all.. Use the template that comes with these installation instructions for the OEM CC installl.
I’ll take some pictures of mine and will post then shortly...


Originally Posted by teddy ↑
Can somebody with the OEM cruise & steering wheel cover please post a picture showing the hole where the stalk comes out? Doesn't even have to be a DIY job, even with it installed from the factory.

I'm thinking about picking up an OEM steering wheel cover with the pre-cut hole. The one I drilled is a bit of an eye sore.. much larger than it needed to be because I drilled it in the wrong spot and had to adjust a few times.

thanks
teddyOntario, Canada · Apr 25, 2011#170
Originally Posted by CB900F2 ↑
Teddy and all.. Use the template that comes with these installation instructions for the OEM CC installl.
I’ll take some pictures of mine and will post then shortly...
Wish I had that template before I drilled the hole! Found it a few days after it was all done.

I was going in blind essentially. This considered I didn't do that bad, but it's a little rough around the edges.
SKurjGTA · Apr 25, 2011#171
Excuse my expletives... but my local dealer quoted me $700 for an aftermarket cruise today...

Guess I will be trying my hand at this DIY.....
teddyOntario, Canada · Apr 25, 2011#172
Originally Posted by SKurj ↑
Excuse my expletives... but my local dealer quoted me $700 for an aftermarket cruise today...

Guess I will be trying my hand at this DIY.....
$700? ouch, though believable if you've got a 2004 Echo. The Yaris uses drive-by-wire so the cruise control is entirely computer controlled. With the Echo they'd need to install mechanical controls to maintain the throttle position.

Mine was just a hair over $500 for the third party Rostra cruise which I had removed in the fall when there was an optional recall.

I don't think this DIY will work for you. If you know what you're doing you could probably find the Rostra kit online far cheaper than the dealer wants but you'll be getting your hands dirty installing it.
SKurjGTA · Apr 25, 2011#173
No my 04 has cruise already, installed by toyota for $300 in 2006. This time its my 2009 5spd 3dr.
teddyOntario, Canada · Apr 25, 2011#174
Originally Posted by SKurj ↑
No my 04 has cruise already, installed by toyota for $300 in 2006. This time its my 2009 5spd 3dr.
In that case, join the club with DIY cruise!! 😆
liam6200Carlisle, UK · Apr 25, 2011#175
hi, im from the uk, i have a 2010 yaris 1.4 diesel, would this work on my yaris?
CTScottThread starterUSA, CT · Apr 25, 2011#176
Originally Posted by liam6200 ↑
hi, im from the uk, i have a 2010 yaris 1.4 diesel, would this work on my yaris?
No. Only USDM Yaris with the 1.5L engine have the cruise control functionality built into their ECM.
liam6200Carlisle, UK · Apr 25, 2011#177
Originally Posted by CTScott ↑
No. Only USDM Yaris with the 1.5L engine have the cruise control functionality built into their ECM.
🙁 ok thanks anyway
CB900F2Toronto · Apr 27, 2011#178
Photos of my OEM CC install


Originally Posted by CB900F2 ↑
Teddy and all.. Use the template that comes with these installation instructions for the OEM CC installl.
I’ll take some pictures of mine and will post then shortly...
IMG_7024.JPG
teddyOntario, Canada · Apr 27, 2011#179
Is that with the OEM steering wheel cover (with the pre-cut hole?) That's specifically what I'm looking for.
CB900F2Toronto · Apr 27, 2011#180
Hi Teddy.. That is the OEM steering wheel cover, but I drilled the hole using the template.

Originally Posted by teddy ↑
Is that with the OEM steering wheel cover (with the pre-cut hole?) That's specifically what I'm looking for.
CTScottThread starterUSA, CT · Apr 27, 2011#181
Here's a picture of one with the OEM stalk hole.

OEM Cruise Stalk Hole.jpg
white_riceOntario, Canada · May 4, 2011#182
Can someone please tell me what the functionality is of the single OEM wire/pin that plugs into the D3 connector on the steering column? I ask because I need to replace this connector but want to know what I'll be unhooking exactly, once removed.

Thanks.
CTScottThread starterUSA, CT · May 4, 2011#183
Originally Posted by white_rice ↑
Can someone please tell me what the functionality is of the single OEM wire/pin that plugs into the D3 connector on the steering column? I ask because I need to replace this connector but want to know what I'll be unhooking exactly, once removed.

Thanks.
The black wire is for the horn.
SKurjGTA · May 11, 2011#184
Ok so my steering wheel cover came in today. I followed all the steps, and kept saying to myself.. too good to be true... too good to be true....

Everything back together, start the car.. airbag light won't turn off... uh oh here we go, what did i break or do I need to run some wire to some pin...

Pop the airbag off again, and notice I hadn't pushed the yellow clips back in. Didn't figure that could be it, but put it back together and started it again. The light went off!!

Too good to be true... Too good to be true...

Test drive time, I notice the cruise indicator on the dash works, good sign. The damn cruise does everything its supposed to flawlessly.. for less than $100... and 30 minutes labor..

Makes no sense toyota doesn't offer this cruise..

Many thanks to Scott for this!

And in this case it's everything its claimed to be.


P.S. If anyone wants the stock steering wheel cover without hole cut, just cover shipping and its yours (note I am in Toronto Area).
burdenjEast York, Ontario, Canada · May 14, 2011#185
Hi everyone, first substantial post here!

Thanks to this awesome community, my 08' Hatchback now has cruise as well, just put the finishing touches on it this morning.

Please forgive the dirt, it's only just barely spring in St. John's, Newfoundland. Also, that mess that looks vaguely like a circuit is all tidy and covered in heat shrink now 😉

For the switches, I used double throw momentary toggles which are off at the centered position. I know it doesn't look stock like some of the push button switches do, but I just have a thing for toggle switches.

I got them from Digikey if anyone's interested (450-1530-ND).







Brianr4New Orleans · May 14, 2011#186
Finally finished installing all of mine and it works perfect!
I think it works better then the factory cc in my Tundra.

Have to give much thanks to CTScott for making the kit...selling the kit...and for being so patient with all my questions!

His brain must be super huge!!!!
SaggioSeattle WA, · May 17, 2011#187
Installed my kit today from Scott. LOVE it!

Thanks again!!!
Brianr4New Orleans · May 17, 2011#188
Scott, did the horn plug make it back to you?
CTScottThread starterUSA, CT · May 25, 2011#189
Originally Posted by bobor ↑
Hi everybody,

I own my small Yaris and like the car very much. The only minor thing I miss is the CC feature. Since the european models do not have support for CC built in ECU and I do not want to invest too much money in some aftermarket model, so I decided to build my own one.
The idea is very simple. I would like to use a microcontroller to periodically check all necessary input data (current speed, brake & clutch pedal positions, etc.) and then set the digital2analog converter to emulate the accelerator pedal movement by increasing / decreasing the output voltages on both lines to ECU as the speed of the vehicle is under / over set value.
I currently have an open question related to accelerator pedal connection. There are 6 wires for 2 separate Hall probes to detect the pedal position. Of each set, one wire is +5V, second one is GND and the third one is the output, where voltage changes according to accelerator pedal depression level. I would like to cut these two signal lines and put them as input to CC module and connect another two wires (output from CC) as input to ECU. So far so fine.
But my idea is, that during the time CC is switched off, the signal input and output are directly interconnected and when CC is enabled, the output is fed from DAC. I would like to use a relay controlled by microcontroller for this purpose (see fig.). but I am not sure, if it is a good idea. What is your opinion. Is there any better solution for this?
If I use the relay, will there be any problem with temporary loss of signal to ECU during relay switching (the actual switching time is approx. 5 ms)? Or shall I add some small capacitor between output & ground to smooth the glitches. But I have no idea what capacity to use in order not to influence the response time of accelerator pedal too much.
And finally, do you know about any place where can I get at least accelerator pedal connectors (male & female) or the whole accelerator interface harness from ?
I appreciate any ideas. Thanks
With the amount of development required to safely implement cruise control, I would think that in the end run it will be less expensive to use an aftermarket cruise control system. I realize that the primary aftermarket system available in Europe is very expensive (~$700 US), but I believe that the Rostra aftermarket cruise control system, which is sold in the US and Canada for ~$200 US, will work on the European Yaris.
CTScottThread starterUSA, CT · May 25, 2011#190
Originally Posted by bobor ↑
Hi CTScott,
thanks for your response. I admit its time consuming process and there are many risks to consider, but it's my hobby 🙂 At the moment I would say I have 90% of the source code ready, so there are only minor modifications to be done and a lot of testing and bug fixing 🙂 But except my free time I invest into it, the parts will cost me not more than 20 EUR ( ~30USD).
Regarding the aftermarket models, the situation is slightly better than you expect, at least here in Slovakia. I can get one for ~450 USD, but still Rostra model even including shipping costs would be cheaper. And I don't see any reason why it should not work on European models.

But as I said, it's a hobby.
OK. In that case, back to your original question - I would not use mechanical relays. I would stick with solid state switching, by transistor or FET, to avoid the switching delays.
CTScottThread starterUSA, CT · May 26, 2011#191
Originally Posted by bobor ↑
Unfortunatelly I do not have any experience with solid state switching. If you could point me to some good tutorial, I would appreciate it 😉 But AFAIK in this case, the input signal (voltage level) from either accelerator pedal (hall probes) or DAC would be somehow degradated (lowered) due to voltage drop PN junction.
Solid state switching is definitely faster than mechanical relay. But advantage of a relay is that it does not require power supply to interconnect one of the input lines to the ouput. I though of using this a safety mechanism, so in case anything goes wrong I would just switch off the power supply to cruise control module and the relay would (almost immediatelly) switch back to default state (direct connection of accelerator pedal). But if I find some good solution using solid state, I am about to change my mind.
Here's a pretty good intro to transistor switching.

http://www.kpsec.freeuk.com/trancirc.htm


Rather than switching back and forth, it may actually make more sense to put the microcontroller in between the pedal and the ECM. That way, the ECM samples the pedal outputs and then in normal mode, just emulates what it sees. Then, in CC mode it ignores the input and sends its own output.

The other advantage of this method is that you can improve the throttle response in normal mode (like the Blitz throttle controller does).
CTScottThread starterUSA, CT · May 26, 2011#192
Originally Posted by bobor ↑
Thanks for the link, I will have a look on it. Your idea seems quite interesting, maybe I will change my plans a little bit and implement it that way. But I still have a feeling, that switching between DAC and pedal accelerator outputs is a little bit more safer.

Another idea came to my mind how to avoid switching delays with a relay. If I connect the DAC output directly to output line of the relay (to ECM) and accelerator pedal to one input of the relay (the second input remains unused), I can first set the output voltage on DAC and then switch the relay (cut the accelerator pedal line). On a switch back, the accelerator pedal is switched on first and then DAC disabled. This way, there is no voltage drop on signal line to ECM.

The only drawback is, that all time, when DAC is not in use (even just before switching off the accelerator pedal line, when DAC output is set) there is voltage from accelerator pedal to DAC output. I have no idea, if it can harm it in any way and what the impedance between DAC output and ground. If the impedance is too low, it can make a short connection and damage the ECM, that I obviously would like to avoid 🙂

And finally, do you have any idea, what size the input impedance of ECM could be?
The impedance on the ECM input pins is approximately 2K Ohms.
49erRiderCharlotte, NC · Jun 3, 2011#193
Couldn't get mine to work and tried searching these posts but has anyone else had an "a ha" moment when theirs didn't work and want to share?
CTScottThread starterUSA, CT · Jun 3, 2011#194
Originally Posted by 49erRider ↑
Couldn't get mine to work and tried searching these posts but has anyone else had an "a ha" moment when theirs didn't work and want to share?
The most common one with 06-08's, when using the OEM stalk is not properly seating the ECM pin. The check for that is to measure the voltage on the wire connected to the ECM pin with the ignition switch in the on position (engine not running). It should measure 12 Volts with no buttons pressed on the stalk. If it does not, then the pin is not seated properly or is in the wrong location.
49erRiderCharlotte, NC · Jun 4, 2011#195
I figured it out! I had 12volts to the ECM pin so that wasn't the problem. When I drive I ride with my foot just resting on the clutch. That was enough to remove pressure from the plunger causing it to not activate.

Works great, another thankful yaris owner Scott!
haydendfw · Jun 12, 2011#196
Hey CTSCott - if you remember I bought a CC stalk from you along with the wiring kit. It worked fine for a month or two and you may remember me posting that it stopped working occasionally and would also sometimes make the car accelerate on it's own.

It eventually stopped working entirely but just now had time to go out with a multimeter to test it. This was done about a foot of wire away from the computer thingy (on the firewall in the engine bay) at one of those snap-close connectors I used. The ignition was on (I know you told me to do it with the ignition off, but hopefully this works too) but the engine off.

Car on but engine off: 12.3v
With the on/off button held: 0.2v
Held down: 6.1v
Held up: 3.4v
Held toward: 8.6v

Any idea why the CC wouldn't be working AT ALL? I have no idea what these values are supposed to be. I'm concerned that maybe the wire thickness I used may be too much, but I have no idea how these things work. I think it was the same type that you used in the wiring kit (had to buy extra from radio shack).

Thanks a ton for your help!
CTScottThread starterUSA, CT · Jun 12, 2011#197
Originally Posted by hayden ↑
Hey CTSCott - if you remember I bought a CC stalk from you along with the wiring kit. It worked fine for a month or two and you may remember me posting that it stopped working occasionally and would also sometimes make the car accelerate on it's own.

It eventually stopped working entirely but just now had time to go out with a multimeter to test it. This was done about a foot of wire away from the computer thingy (on the firewall in the engine bay) at one of those snap-close connectors I used. The ignition was on (I know you told me to do it with the ignition off, but hopefully this works too) but the engine off.

Car on but engine off: 12.3v
With the on/off button held: 0.2v
Held down: 6.1v
Held up: 3.4v
Held toward: 8.6v

Any idea why the CC wouldn't be working AT ALL? I have no idea what these values are supposed to be. I'm concerned that maybe the wire thickness I used may be too much, but I have no idea how these things work. I think it was the same type that you used in the wiring kit (had to buy extra from radio shack).

Thanks a ton for your help!
Those voltages are fine (and that is correct to measure them with the engine off, but ignition on).

Try wiggling the ECM Pin while measuring to make sure that the connection is not intermittent.

Can you refresh my memory on if you have an AT or MT?
haydendfw · Jun 13, 2011#198
It's an AT 2007 2 door.

If there was no connection at all to the ECM, would that line still be powered? I'll go reseat the pin and see if that helps because it was definitely intermittent before dying entirely.
CTScottThread starterUSA, CT · Jun 13, 2011#199
Originally Posted by hayden ↑
It's an AT 2007 2 door.

If there was no connection at all to the ECM, would that line still be powered? I'll go reseat the pin and see if that helps because it was definitely intermittent before dying entirely.
That wire would be zero volts if disconnected. But, it could be connected when still and intermittently disconnected when the engine starts shaking it.
haydendfw · Jun 13, 2011#200
Originally Posted by CTScott ↑
That wire would be zero volts if disconnected. But, it could be connected when still and intermittently disconnected when the engine starts shaking it.
Reseated the pin, no luck. I'll try going out there and wiggling it while taking a reading to see if I can make it go to 0. Any other advice if that shows up fine though?