Sweet. Many thanks, and when the parts get here (next week), I'll update on how it goes! (So very much hoping the airbag doesn't explode...)
DIY Cruise Control FAQ (2006-2010 Yaris)
416 posts · 835,665 views · page 7 of 9
Replies continued
Do I need to buy the screws that are linked with the cruise control stalk or can I find them at Lowe's? If at Lowe's, what size/type screws are they?
They are just M5 x 10mm long screws. I include them with the stalk, when I sell them.Originally Posted by CodyTheBody ↑Do I need to buy the screws that are linked with the cruise control stalk or can I find them at Lowe's? If at Lowe's, what size/type screws are they?
Parts came early, installation went perfectly. Huzzah!
Many thanks, CTScott.
Many thanks, CTScott.
Awight, so apparently I need the D3 pins. Should I PM you for shipping/purchasing them?
Also, Pin 40 on the ECM is the second hole from the end right? If so, it is taken by a blue wire, which is connected to Pin 6 of AD4 up under the dashboard, according to DIY Guide you wrote.
So what do I do with that blue wire? Take it out? The guide says tap onto it with the ECM A4 connector but I'm not real sure how. Any advice?
Also, Pin 40 on the ECM is the second hole from the end right? If so, it is taken by a blue wire, which is connected to Pin 6 of AD4 up under the dashboard, according to DIY Guide you wrote.
So what do I do with that blue wire? Take it out? The guide says tap onto it with the ECM A4 connector but I'm not real sure how. Any advice?
Yes, you can PM me.Originally Posted by CodyTheBody ↑Awight, so apparently I need the D3 pins. Should I PM you for shipping/purchasing them?
Also, Pin 40 on the ECM is the second hole from the end right? If so, it is taken by a blue wire, which is connected to Pin 6 of AD4 up under the dashboard, according to DIY Guide you wrote.
So what do I do with that blue wire? Take it out? The guide says tap onto it with the ECM A4 connector but I'm not real sure how. Any advice?
If your 09 sedan doesn't have the power package, then it makes sense that you have the ECM pin populated, but not the d3 pins. The easiest method to make the connection is to use a tap splice connector, which you slide over the wire, slip the connecting wire in, and squeeze it with a pair of pliers.
Yeah, I bought some of those splices as well.
Ok, sorry man for all the questions; just making sure I get this right. I slide the tap splice over the existing blue wire in Pin 40, then connect the new A21 wire into the splice then squeeze and then carry on to connecting A21 to D3, right? Wanna get it right the first time.
Ok, sorry man for all the questions; just making sure I get this right. I slide the tap splice over the existing blue wire in Pin 40, then connect the new A21 wire into the splice then squeeze and then carry on to connecting A21 to D3, right? Wanna get it right the first time.
Originally Posted by CTScott ↑Yes, you can PM me.
If your 09 sedan doesn't have the power package, then it makes sense that you have the ECM pin populated, but not the d3 pins. The easiest method to make the connection is to use a tap splice connector, which you slide over the wire, slip the connecting wire in, and squeeze it with a pair of pliers.
Correct. And, then the other d3 pin gets connected to ground.Originally Posted by CodyTheBody ↑Yeah, I bought some of those splices as well.
Ok, sorry man for all the questions; just making sure I get this right. I slide the tap splice over the existing blue wire in Pin 40, then connect the new A21 wire into the splice then squeeze and then carry on to connecting A21 to D3, right? Wanna get it right the first time.
I finally got around to installing the parts I ordered from CTScott and they worked a treat!
I noticed the stalk can be very easily scratched, so you might want to leave the plastic bag on until the installation is complete. If you do accidentally scratch it, a little PlastX will have the scratch buffed out in no time. Also, when CTScott says the Torx T30 screws are tight...he is not just joking. Be sure to use a T30 driver that you can put a great deal of force on - a Multi Tool or an L Key won't work as you're sure to break either the tool or your skin.
Thanks again :)
I noticed the stalk can be very easily scratched, so you might want to leave the plastic bag on until the installation is complete. If you do accidentally scratch it, a little PlastX will have the scratch buffed out in no time. Also, when CTScott says the Torx T30 screws are tight...he is not just joking. Be sure to use a T30 driver that you can put a great deal of force on - a Multi Tool or an L Key won't work as you're sure to break either the tool or your skin.
Thanks again :)
Thank again. Worked like a charm! CTScott, u r the man. Thanks bud!
Actually, one more question. Does the "Passenger Air Bag" light near the middle A/C vents always stay on? Or did I screw something up? If there's a problem with the driver air bag, another indicator light will come on in the dashboard cluster next to the speedometer right?
The passenger one is typically always on (Either with airbag on or airbag off being illuminated steady). If it flashes then their is an issue. If you didn't properly connect the steering wheel airbag then the light on the cluster would stay illuminated.Originally Posted by CodyTheBody ↑Actually, one more question. Does the "Passenger Air Bag" light near the middle A/C vents always stay on? Or did I screw something up? If there's a problem with the driver air bag, another indicator light will come on in the dashboard cluster next to the speedometer right?
Sweet. Thanks man!! You've been a big help! With my alloy rims instead of caps, cruise control and new tint, my non-power Yaris just got upgraded haha
great info - thanks for everyone who provided photos and information.
I just wanted to hear from anyone in Australia who has added cruise control to their Yaris? From what this thread seems to indicate, the actual ECU on the Australian Yaris' are not able to have cruise control functioning. Therefore am i correct in my assumption that you have to "tap" into a speed control or sensor wire somewhere for Australian Yaris'? Does the instrument panel still have the cruise control indicator on the Australian models?
I'd love to be able to just get this working on my Yaris YRX 2010 (NCP91R) automatic - preferably the kit shown here and not some other random aftermarket kit. Any helpful points would be great.
p.s i did a search on "YARIS cruise control Australia" but didn't find the answers I was looking for.
thanks!
I just wanted to hear from anyone in Australia who has added cruise control to their Yaris? From what this thread seems to indicate, the actual ECU on the Australian Yaris' are not able to have cruise control functioning. Therefore am i correct in my assumption that you have to "tap" into a speed control or sensor wire somewhere for Australian Yaris'? Does the instrument panel still have the cruise control indicator on the Australian models?
I'd love to be able to just get this working on my Yaris YRX 2010 (NCP91R) automatic - preferably the kit shown here and not some other random aftermarket kit. Any helpful points would be great.
p.s i did a search on "YARIS cruise control Australia" but didn't find the answers I was looking for.
thanks!
to you Scott
Originally Posted by neromaverick ↑First of all thanks for everybody that contributed to this, you're awesome 🤘.
I'd like to clarify, in the hopes this may turn up in future Google results posts, the OEM style upgrade does in fact work on the 2010 Yaris Hatchback USA Manual Package (I'm not referring to manual transmission, but manual window/locks/etc.). Everywhere I looked most people either had the power package, the sedan, or both. For those not knowing what to get, I grabbed this from a post above:
84632-08021 Cruise Control Engagement Switch (refered to as 'control stalk' in other posts)
84633-02020 Cruise Control Switch Wire
90159-50199 Screws (order quantity of 2)
45184-52130-BO Cover Steering Wheel (comes with the hole already in it for the cruise switch)
The post also mentioned getting the parts from http://www.toyotapartscheap.com/
The prices there are a little higher than places like ebay, amazon, etc. but it's a one-stop kinda deal, no guessing & hoping you're getting the right part. Not to mention their customer service is really great.
Just thought I'd give my 2cents. Again, wonderful guides, FAQs, and people on this board, thanks again so much 👍
As a clarification - All 09+ liftbacks have the wiring to the steering column. Sedans are the ones which do not if they do not have the power package.
To save those looking some significant money - I stock all of the parts required except for the lower steering wheel cover (which I prefer to drill anyway). I sell the stalk, wire and screws for $40 shipped to the US or Canada, which is less than half of the $86.55 + shipping which that site sells them for. I also carry the wiring parts required for pre-09 Yaris as well.
Hello, I want to do this on my 2008 YarisHB, I made the 4 switch assembly, I found the D3 connector but the problem is that my ECM is BOSCH and the A21 plug is different. Is bigger with twice the number of pins and I don't know where to put the wire that had to be in the nr 40 pin on the A21 connector. Any suggestions? And I saw that I have 2 switches on my clutch peddal: on that works when tha clutch is pressed, witch is used to start the car because mine has the Start&Go button, and there is another switch near the stop bolt, so I guess I dont't need to buy this switch anymore.
Unfortunately cruise control is not programmed into the ECM of 2007-2011 European Yaris, so this will not work for you. You would need a complete aftermarket cruise control kit, which appear to be very expensive.Originally Posted by iacubovici ↑Hello, I want to do this on my 2008 YarisHB, I made the 4 switch assembly, I found the D3 connector but the problem is that my ECM is BOSCH and the A21 plug is different. Is bigger with twice the number of pins and I don't know where to put the wire that had to be in the nr 40 pin on the A21 connector. Any suggestions? And I saw that I have 2 switches on my clutch peddal: on that works when tha clutch is pressed, witch is used to start the car because mine has the Start&Go button, and there is another switch near the stop bolt, so I guess I dont't need to buy this switch anymore.
I see, 10x for the answer
Many Japanese market vehicles do not support cruise control. The presence of only two male pins on the steering column end of the D3 connector tells me that your Fielder likely does not.
Since the car is built with a spiral cable that does not have enough wires to support cruise control, it is unlikely that the ECM is programmed for it.Originally Posted by FIREPROOF5 ↑cant we connect the CC stalk wires (in ur blog) blue and brown directly to ECM after all the clips in between are also doing the same i.e sending electric signals
In doing a bit more research on the Axio Fielder, the ones with the same engine as the Yaris (1NZ-FE) do not support cruise control, but the ones with the 2ZR-FE engine do.
I have a 2011 Yaris 5 speed MT, No power , Can i still do the cruise control
Yes you can. You will just need to do an extra piece (adding the connector D3 pins and running the wire from them to the ECM connector).Originally Posted by adamcorey23 ↑I have a 2011 Yaris 5 speed MT, No power , Can i still do the cruise control
Dear Scott,
First of all received your wires 2 weeks ago and as I was out of state was only able to install everything yesterday. My car being a Thailand build Camry 2.0 was quite tight under the dashboard. It works like a charm.I am now happily crusing on my Malaysian highways.
Thanks a million Scott for all the info I needed to make this happen....
First of all received your wires 2 weeks ago and as I was out of state was only able to install everything yesterday. My car being a Thailand build Camry 2.0 was quite tight under the dashboard. It works like a charm.I am now happily crusing on my Malaysian highways.
Thanks a million Scott for all the info I needed to make this happen....
Will this be possible on european toyota yaris 2010?
Hmmmm got 89661-0dd90... No idea if it supports cc....
Doesn't cruise control usually consume more gas than without it? I would probably start falling asleep if I had it on for too long
First of all thank you CT Scott for such helpful guide, I did it to my 06 PR spec Yaris and its been working like a charm for 6 months, I just have a question, Can I use a US S spec cluster (2010) to have the indicators working? I just ordered one from ebay.
Unfortunately the indicator will not work unless you also upgrade the ECM to a 2009 or newer one as well.Originally Posted by jose3sgte ↑First of all thank you CT Scott for such helpful guide, I did it to my 06 PR spec Yaris and its been working like a charm for 6 months, I just have a question, Can I use a US S spec cluster (2010) to have the indicators working? I just ordered one from ebay.
I offer an indicator module, which can be used with 06-08 Yaris, which lack the cluster indicator. See my cruise control DIY below for more info on it.
Is the ecu plug n play? Or I have to look for one in particular? (US or PR spec), Thanks
It is plug and play if it is properly matched. You would need a PR spec one. You would also have to match the car's features - Transmission type, engine immobilizer or not, ABS, Traction control, etc.Originally Posted by jose3sgte ↑Is the ecu plug n play? Or I have to look for one in particular? (US or PR spec), Thanks
Clear, concise instructions. Close-up pics. Couldn't have completed the job without this info.
Thank-you.
Thank-you.
is anyone know, will the Rostra cc kit work on Australia model (2007) manual sedan,
Thank
Lewis
Thank
Lewis
I am about 90% sure that the older (discontinued) Rostra kit will work with any of the non-US Yaris that do not have cruise control functionality built into the ECM. The newer kits definitely will not as they are just an overpriced version of the parts that I sell and require the ECM to have the functionality.Originally Posted by YarisBasic ↑is anyone know, will the Rostra cc kit work on Australia model (2007) manual sedan,
Thank
Lewis
do you have the Rostra kit part no.? or do you sell the older kit?
Thanks
Thanks
The discontinued Rostra kit was 250-1797 for MT and 250-1796 for AT.Originally Posted by YarisBasic ↑do you have the Rostra kit part no.? or do you sell the older kit?
Thanks
I actually have one of the kits in my possession.
Do the connectors on the ECM on your Corolla look like the 2006-2011 Yaris connectors or like the 2012+ Yaris connectors?Originally Posted by trionons ↑Hi, I'm from the Ukraine and i have a 2012 Corolla, 1.33 1NR-FE. This version made in Japan only for Russia, Ukraine and other countries of the former USSR. Quation is simply: would cruise work on my Corolla? Because i now, that on 1.6 Corolla it work http://www.toyotaownersclub.com/foru...-instructions/, but in my case it not (( I can tell, I have tried to check voltage between ECM 40 Pin and Ground when ignition On, but result is 0v ! Maybe it not the fact, that ECM for Yaris and Corolla are same? But how to know which pin to check in Corolla 1.33 1NR-FE?
2006-2011:

2012+:


OK. In that case from what I have seen of other Toyota vehicles that use that same connector (the Camry for instance), cruise control is pin 40 of the smaller connector as well. So, that means that you reading 0V on that pin on yours likely means no cruise control for you.Originally Posted by trionons ↑Look like 2006-2011.
Unfortunately correct.Originally Posted by trionons ↑Miserably, but I need to hear it from you to calm down ))
In other words: it just does not provide by the firmware ECM.
Anyway, good-bye cruise!
Hi Guys,
Have been using the CC on my Thailand built Camry for almost 5 months now and enjoying every minute of it. Again thanks to CTScott.
Have been using the CC on my Thailand built Camry for almost 5 months now and enjoying every minute of it. Again thanks to CTScott.
Hi Scott (or anyone else who might have some insight). My friend has a 2004 Toyota Echo 2 door Hatchback (non RS). He wants to know if there is a DIY Cruise Control method like this for his car as well. He really wants cruise added for his daily work commute. I told him if anyone knows it will be the guys on here.
No. The Echo was cable throttle, so installing cruise control would mean adding a vacuum operated throttle cable actuator as well as the electronics to control it.Originally Posted by white_rice ↑Hi Scott (or anyone else who might have some insight). My friend has a 2004 Toyota Echo 2 door Hatchback (non RS). He wants to know if there is a DIY Cruise Control method like this for his car as well. He really wants cruise added for his daily work commute. I told him if anyone knows it will be the guys on here.
I bought the stalk for my '10 sedan on ebay, but the car got wrecked before I installed it.
I've got a '12 sedan AT, with what seems to be a partial Power Package (windows only, not locks, etc.). I'm assuming that the stalk is the same? Any idea what the wiring requirements are for this year/model?
I've also read the tutorial multiple times, but remain a bit confused about D3. I get that there are supposed to be 3 wires in it-one of them being ground and two that are added-but where is the other end of the wires?
I've got a '12 sedan AT, with what seems to be a partial Power Package (windows only, not locks, etc.). I'm assuming that the stalk is the same? Any idea what the wiring requirements are for this year/model?
I've also read the tutorial multiple times, but remain a bit confused about D3. I get that there are supposed to be 3 wires in it-one of them being ground and two that are added-but where is the other end of the wires?
Thanks Scott, So I'm gathering his best bet would be to find a wrecked RS version (or any one equipped with factory cruise) and just swap over all of the OEM components.Originally Posted by CTScott ↑No. The Echo was cable throttle, so installing cruise control would mean adding a vacuum operated throttle cable actuator as well as the electronics to control it.
That would be the best bet, as it would be pretty expensive to purchase all of the parts separately.Originally Posted by white_rice ↑Thanks Scott, So I'm gathering his best bet would be to find a wrecked RS version (or any one equipped with factory cruise) and just swap over all of the OEM components.
The stalk is the same for '10 and '12.Originally Posted by abarson ↑I bought the stalk for my '10 sedan on ebay, but the car got wrecked before I installed it.
I've got a '12 sedan AT, with what seems to be a partial Power Package (windows only, not locks, etc.). I'm assuming that the stalk is the same? Any idea what the wiring requirements are for this year/model?
I've also read the tutorial multiple times, but remain a bit confused about D3. I get that there are supposed to be 3 wires in it-one of them being ground and two that are added-but where is the other end of the wires?
Did you look at your D3 connector yet? If you have the three wires there, then you just need to install the stalk. If you do not, then one goes to ground and the other to the ECM connector. See my complete DIY below for details:
DIY: 2006-2011 Yaris OEM Cruise Control Complete Installation
It works! Took an hour only because the horn wire broke. D3 was already wired, although the block looks different on the 2012.
Thanks so much for posting this tutorial!
Thanks so much for posting this tutorial!
Thank you so much for this thread! I have a Base Yaris which could benefit from CC.
CTScott, Do you still sell the switch and wires needed to do this modification?
CTScott, Do you still sell the switch and wires needed to do this modification?
Yes. I still have all of the cruise control parts available.Originally Posted by Neil-R ↑Thank you so much for this thread! I have a Base Yaris which could benefit from CC.
CTScott, Do you still sell the switch and wires needed to do this modification?
Hi there would anybody be able to tell me if my T3 Yaris will support cruise control? It is a south African spec. I am not sure if i will need a cruise control module?
Or, how can i check if it has
Or, how can i check if it has