Yarisworld Archive

DIY Cruise Control on 07-08 Yaris (step by step)

415 posts · 355,617 views · page 5 of 9

Replies continued

CTScottUSA, CT · Apr 5, 2010#201
Originally Posted by yongtaufoo ↑
Hi Scotts,

Thank you so much for your reply. 🙂

But im puzzle about another thing. If referring to the cruise control switch schematic, turning cruise control ON-OFF will short ECM Pin40 12V to ground. Will I then damage my ECM by doing this since it is outputing a 12V? And ECM Pin40 is an input or output port?

Thanks!
Pin 40 is an analog to digital port on the ECM. The 12 volts is a reference voltage and the ADC has about 2k ohms of internal resistance, so shorting that pin to ground just brings the ADC to the bottom of it's 0-12 volt input range.
weaver615New York · Apr 5, 2010#202
Originally Posted by yarstar ↑
I want to pass on a couple of 680 ohm resistors that I was given to anyone who needs them. You only need one to do the 2-button setup. PM me with an address and I'll mail one to you.
I too have a few of the 680 ohm resistors that I can donate to someone looking to do the 2 button setup. I also have some 120 ohms too if someone wants to do the 3 button setup like I did. PM me your address and I can send them out to you.
kazama82Malaysia · Apr 8, 2010#203
Originally Posted by CTScott ↑
If it does have it, then you can do the wiring as above. For the indicator, you can shine a flashlight on the panel to see what indicators are there, and if the cruise ones are.
hi scott,

i see this post on opening the ECM. If i dc the battery, how do i measure the 12V?

DIY - How to remove or insert a pin on the ECM Connector A21

very very sorry for asking a noob question...i have a DVM with me but dunno which wire/connector i need to measure to make sure my car having cruise control function...hope can get some help ...thanks..
CTScottUSA, CT · Apr 8, 2010#204
Originally Posted by kazama82 ↑
hi scott,

i see this post on opening the ECM. If i dc the battery, how do i measure the 12V?

DIY - How to remove or insert a pin on the ECM Connector A21

very very sorry for asking a noob question...i have a DVM with me but dunno which wire/connector i need to measure to make sure my car having cruise control function...hope can get some help ...thanks..
To take the measurement you would need to do so with the battery still connected and the ignition in the on position. For actually doing the wiring I suggest that people disconnect the battery, while doing so.

You can stick a pin through the rubber plug in that pin location of the ECM connector to take the measurement.

Based on others experience, I don't believe that your car's ECM will have the cruise control functionality.
kazama82Malaysia · Apr 8, 2010#205
really?..too bad then..if so, i will not bother to check the ECM voltage then..:(..thanks scott..
swiddCentral Alabama, GOD BLESS AMERICA · Apr 12, 2010#206
YAAY! It worked! It was even quite easy. The soldering with a barely warm over-sized soldering iron was the only tedious part, and getting the ECU connector apart proved harder than it needed to be because I pushed the little rubber piece in instead of out first...
My wiring, routing and resistors and stuff looks really amateurish, but whatever, so long as it works and doesn't catch on fire, and as long as nobody from Toyota sees it :)

To the guy with the picture of the 4-way switch installed in the switch place between the seats... good job! You made it look good, and I don't know how, because I could not get the switch to fit there without cutting into the panel and molest the empty switch cover.


Clutch Switch $23
ECU wire (made installation a lot easier, I routed this short wire into the grommet right behind the ECU, and spliced it to the switch wire behind the glove box, super easy). $17.
4-way switch $22.
Total: $62, and about 4 hours of fiddling.
Henry G.So Cal. · Apr 16, 2010#207
Where does everyone get this "repair connector", is it a toyota only product, ior can I get it at Radio Shack? Is there a part number, what is the proper name. I have the car torn apart now, and dont just want to shove the wire into pin 40 hole. Thanks for any help..
BTW there is NO WAY this is a 45 minute DIY...but so far so good.
OK never mind did a better search and found, looks like another trip to the toyota dealer, yeah!

OK, went to the dealer, $15 bucks!!!!?? No f'ing way! And they would have to order it.
So back to Radio Shack, had to buy 5 different 1/4 watt resistors to make up the required combinations, having to use 2 to 3 resistors in series. I check them with my multi-tester, most of them show no value, even the new ones I did use, about 25% show the correct value within 5%...WTF? So I have the switch panel wired, but cannot read values on most of the resistors, some I can read but I have to switch to 2k or 20k, but most of the rest still read zero continuity. Im frustrated to say the least.
Henry G.So Cal. · Apr 17, 2010#208
Well made some progress, close to getting it working. Should have worn my glasses, I bought 22k and 100k resistors instead of 22 and 100 ohm. Went back to Radio Shack where I am practically on a first name basis now with the employees, got the $12.99 500 pack, so I will have a bunch to give away when the job is done. Tried to unsolder the wrong resistors out of the loops, and melted one of the micro NO switches. Looks like I will be rebuilding my switch pad from scratch, not going back into town again today.
On the up side, got a wire, folded over twice and soldered to fit into pin 40 on the ecm harness, with a confirmed 12+ volts so it seated. I routed the wire through the heater hose/tube grommet, very soft and pliable, taping the wire to a coat hanger and carefully working it through worked. Same for the clutch switch wires. I used small terminals which stuffed quite nicely down into the fuse block connections for clutch wires where the jumper goes, worked good.
I will post pics tomorrow AFTER I get more switches and get this SOB working.

Just a few observations and suggestions which may or may not have been mentioned along the way: Remove the ECM for the firewall, and undo the wire loop holders to pull the whole thing out. The ECM connectors are GARBAGE IMO, and are a PITA to remove and replace. They appear to literally be meant for only several uses, despite being gentle. At least getting the thing off the firewall allows you to get a better look and grasp at it. Another thing, did I mention the ECM conncectors are crap? My Chevy is built for at least 100 R&R's, with a screw securing the PCM connectors. This is stuff cheap, be careful and dont use much force. I got them on and off again without damage, but it was not simple. As usual with jobs like this, you need the hands the size of a 3 year old with the strength of a 20 year old. Another thing, make sure you have ALL the parts before you start, I just assumed I would run down to the dealer and store and they would have everything I needed, not the case. Also, get a multimeter if you dont have one, you will need it often.
Allow at least 4 hours for ripping the car apart, making the switch pad, shoving wires through the firewall, installing the clutch switch and wires, and screwing around with ECM connectors. Get the Toyota repair connector, I lucked out after several tries by shoving a soldered wire down there with needle nose pliers, but you may not. And get soldering flux, soldering without it is 10 times as hard, plumbers flux works fine. Also get a pad or pile of towels to put on the ground outside the car as you will be spending some time on your knees down there.
Hope to have it working tomorrow, as its going to the dealer for CV joints under extended warranty at 47k Monday.
Henry G.So Cal. · Apr 18, 2010#209
OK, I DID IT!! When I first felt the car accelerate to hold the speed it made it all worth it.
Total cost $50, had to buy multi pack of resistors and second set of switches, still worth every penny.
Picture lost · i53.photobucket.com
Second switch pad ready for install
Picture lost · i53.photobucket.com
Plugged in ready for test drive. I used connectors to unplug the first switch pad and plug in the second correctly wired one.
Picture lost · i53.photobucket.com
Clutch jumper going to fuse box.
Picture lost · i53.photobucket.com
ECM wire tucked into harness
Picture lost · i53.photobucket.com
ECM and clutch wires coming thru heater hose grommet. Im not thrilled with this set up, I will likely get a grommet and drill a hole thru the firewall next to the hoses in the near future.
Picture lost · i53.photobucket.com
Ground wire going to bolt on gas pedal. I couldnt find the previously mentioned ground wire, this worked great, easy to get to. With the plastic re-installed you cannot see this wire at all.
Picture lost · i53.photobucket.com
AND final install.
Thanks for everyone who contributed posts along the way, the DIY and CTScotts expert info, after reading everything it all came together, I made it harder than it had to be by not getting the right resistors up front, and wiring in the wrong ones in the first switch pad. I have some extra resistors if anyone wants them PM me.
Hank
Sodium DuckWestern Mass. · Apr 18, 2010#210
Originally Posted by jthebeh ↑
To anyone that did what I did and pushed the rubber stopper down instead of up. I used a very small drill bit and twisted it with my fingers and it cought and I was able to pull it out. it took me about an hour to get this out, sucked big time
You should have been able to just push it out from the other end with a paperclip. I pushed the wrong way, too.
yongtaufooUSA · May 4, 2010#211
Hi guys,

Any one can advice me where i can purchase the repair wire for ECM pin 40 for cruise control DIY? Its made by Tyco right? Anybody knows the Tyco part number?
CTScottUSA, CT · May 4, 2010#212
Originally Posted by yongtaufoo ↑
Hi guys,

Any one can advice me where i can purchase the repair wire for ECM pin 40 for cruise control DIY? Its made by Tyco right? Anybody knows the Tyco part number?
I posted the Toyota part number in the thread below. Your best bet is to get it from Toyota. I have tried ordering some of the Tyco pins, but they are OEM custom parts, so you can't get them from Tyco distributors.

DIY Cruise Control FAQ (2006-2010 Yaris)
Happy Little PonyTampa, FL · May 4, 2010#213
I must offer major thanks to everyone who has worked so hard on the whole cruise control project.

I just spent the afternoon installing the "two switch" method on my 2007 with manual transmission. It works!
RevssonSoutheast Wisconsin · May 5, 2010#214
Originally Posted by Happy Little Pony ↑
I must offer major thanks to everyone who has worked so hard on the whole cruise control project.

I just spent the afternoon installing the "two switch" method on my 2007 with manual transmission. It works!
Congratulations Happy Little Pony !! 👏

I have the factory cruise, but am trying to talk my buddy into doing this
on his 2007 MT. I also know someone with a 2008 AT that does a lot of
highway driving, and think he should do this to his as well. 🙂
crazyandroidWaco, TX · May 10, 2010#215
Hi there, I have been considering doing this mod and I am waiting on my parts (ordered switches, resistors, and wire from allelectronics.com); however I have one question. I did not see anywhere in here which wire goes where for the clutch switch. I have an '07 sedan w/ MT and I have the Toyota clutch switch, which has two posts and I see that there are two posts to connect to the CC switches in the fuse box. Could someone please clarify for me how to run the wires from the clutch switch to the fuse box connections, if it even matters. BTW, I will have extras of each resistor so if anyone wants em I'll mail them to you, just PM me.
CTScottUSA, CT · May 10, 2010#216
Originally Posted by crazyandroid ↑
Hi there, I have been considering doing this mod and I am waiting on my parts (ordered switches, resistors, and wire from allelectronics.com); however I have one question. I did not see anywhere in here which wire goes where for the clutch switch. I have an '07 sedan w/ MT and I have the Toyota clutch switch, which has two posts and I see that there are two posts to connect to the CC switches in the fuse box. Could someone please clarify for me how to run the wires from the clutch switch to the fuse box connections, if it even matters. BTW, I will have extras of each resistor so if anyone wants em I'll mail them to you, just PM me.
There is no polarity to the clutch switch, so you don't have to worry about which terminal on the switch goes to which of the two wires in the fuse box.

You simply run the two wires from the clutch switch to the two wires in the under-hood fuse box, and make your connections.
crazyandroidWaco, TX · May 10, 2010#217
Originally Posted by CTScott ↑
There is no polarity to the clutch switch, so you don't have to worry about which terminal on the switch goes to which of the two wires in the fuse box.

You simply run the two wires from the clutch switch to the two wires in the under-hood fuse box, and make your connections.
Thank you very much! I can't wait for my switches to come in!
PhillyGgeorgia · May 11, 2010#218
hi guys.. i am very interested in doing this to my yaris. does this work for 2009 as well? i didnt see anyone mention this beyond 07-08.
CTScottUSA, CT · May 11, 2010#219
Originally Posted by PhillyG ↑
hi guys.. i am very interested in doing this to my yaris. does this work for 2009 as well? i didnt see anyone mention this beyond 07-08.
Yes. 09 Liftbacks (and some Sedans) have the wiring in place from the ECM to the steering column, making the job even easier. Take a look at the following thread regarding the differences:

DIY Cruise Control FAQ (2006-2010 Yaris)
PhillyGgeorgia · May 11, 2010#220
Thanks!! i am making a list now.. hope to get to do this in a week or two!
crazyandroidWaco, TX · May 14, 2010#221
🤷 😢 Ok, quick question. When installing the clutch switch, I see that the two wires go to the blue and white wires on that connection in the fuse box . . . could I just splice into those wires instead of trying to wedge some sort of connector into the same hole? I ask b/c that's what I tried and I'm not sure where my failure lies. I will take pictures in the morning of everything that I did and hopefully someone can help me. I'm really feeling like I should not have attempted this mod . . . I don't even know how to check the current to make sure that things are connected adequately. 🤷
CTScottUSA, CT · May 14, 2010#222
Originally Posted by crazyandroid ↑
🤷 😢 Ok, quick question. When installing the clutch switch, I see that the two wires go to the blue and white wires on that connection in the fuse box . . . could I just splice into those wires instead of trying to wedge some sort of connector into the same hole? I ask b/c that's what I tried and I'm not sure where my failure lies. I will take pictures in the morning of everything that I did and hopefully someone can help me. I'm really feeling like I should not have attempted this mod . . . I don't even know how to check the current to make sure that things are connected adequately. 🤷
Definitely splice - Don't wedge. The wedging can be done for a quick test, but you really want a more positive mating for the long run.
YarisduderMontreal, Canada · May 19, 2010#223
Hi, I'm trying to do this on my Canadian 2007 Yaris sedan, and there's already a blue wire in the pin40 spot at the ECM. The wires on the steering column aren't there. Does this mean I can't have CC, or do I tap into that blue wire?
CTScottUSA, CT · May 19, 2010#224
Originally Posted by Yarisduder ↑
Hi, I'm trying to do this on my Canadian 2007 Yaris sedan, and there's already a blue wire in the pin40 spot at the ECM. The wires on the steering column aren't there. Does this mean I can't have CC, or do I tap into that blue wire?
If you are 100% sure that you are looking at the correct pin as pin 40, then indeed your wire is run from there to the junction connector under the dash. (But not from the junction to the steering column).

That junction is just under the top of the dashboard, so you can't get to it without removing the dash, so the easiest thing would be to tap the blue wire by where it enters the ECM.
YarisduderMontreal, Canada · May 20, 2010#225
It worked!! I am amazed and awed! The dealer told me they can't put cruise control on my car, and with a few old buttons and resistors, plus some scraps of wire I now have CC! Thank you all so much, you've saved the Yaris and my $25K for a new car that would be comfortable on long journeys.
sk8manmikeCO · May 23, 2010#226
Originally Posted by CTScott ↑
Definitely splice - Don't wedge. The wedging can be done for a quick test, but you really want a more positive mating for the long run.
What's the best way to go about splicing for the CC switch? Shave the wire coat and solder on to it?
CTScottUSA, CT · May 23, 2010#227
Originally Posted by sk8manmike ↑
What's the best way to go about splicing for the CC switch? Shave the wire coat and solder on to it?
That, or use a properly sized tap splice.
mick.wheelzBrisbane, Australia · May 24, 2010#228
has this actually been tried on an AUDM ECM, I know it does not work on euro models (they seem to run different engines/ECM's alltogether)
mick.wheelzBrisbane, Australia · May 24, 2010#229
Originally Posted by mick.wheelz ↑
has this actually been tried on an AUDM ECM, I know it does not work on euro models (they seem to run different engines/ECM's alltogether)

so i checked my ECM, pin 40 is dead.
CTScottUSA, CT · May 24, 2010#230
Originally Posted by mick.wheelz ↑
so i checked my ECM, pin 40 is dead.
That makes sense. It seems that the cruise control functionality is only programmed in the USDM Yaris ECM.
mick.wheelzBrisbane, Australia · May 24, 2010#231
Originally Posted by CTScott ↑
That makes sense. It seems that the cruise control functionality is only programmed in the USDM Yaris ECM.
that sucks, who has a USDM ECM they want to give me :p
PhillyGgeorgia · May 26, 2010#232
just a side note... i finally got my parts in today. had them shipped to work because for some odd reason shipping to a business is cheaper. was gonna wait till this weekend and do the install.. notice how i said was? well.... during some down time....... it was really super easy! especially since i read just bout every post on the CC subject. many thanks to everyone! it works.. and looks factory!
sk8manmikeCO · May 28, 2010#233
I've run into a problem: I can't get the black wire cover off of the ECM Connector A21.

I've read CTScotts tutorial:
DIY - How to remove or insert a pin on the ECM Connector A21

But i still can't get it off the top so i can insert the wire. I've feel like i'm pulling every direction in can think of to get it off.

Is there something I'm missing?
CTScottUSA, CT · May 28, 2010#234
Originally Posted by sk8manmike ↑
I've run into a problem: I can't get the black wire cover off of the ECM Connector A21.

I've read CTScotts tutorial:
DIY - How to remove or insert a pin on the ECM Connector A21

But i still can't get it off the top so i can insert the wire. I've feel like i'm pulling every direction in can think of to get it off.

Is there something I'm missing?
Once you remove the tiewrap, to remove the black strain relief/cover piece you pry it out, or squeeze it and pull up. It is snapped into the back of the connector.
sk8manmikeCO · May 28, 2010#235
HOLY CRAP......

Ok let me tell you about the scary thing that happened to me right when i was about to get done with this mod.

I finished attaching my switch to the ECM and was now going to do the wire jump in the fuse box on my 07 MT Yaris..........

I put the first wire inside next to the white cable on the right and as I was putting the cable into the slot with the blue cable --- the car freaking lunged forward about 6 inches. Needless to say it scared the s**t out of me. I had the car on halfway (engine off - lights on), so i thought maybe it just did that because i had it kinda on. I turned it all the way off and tried again - same thing happened.

I attached pictures below to show you what i did and can take more if need be.

So whats going on guys? You think theres something wrong with my switch - like the buttons are always on or something?

When it lunges forward and always sounds like it wants to start - i think it stops because i pull the wire out when it lunges at me.

Any advice?





Picture lost · i45.tinypic.com
ECM CONNECTOR

Picture lost · i47.tinypic.com
CURCUIT BOARD

Picture lost · i48.tinypic.com
FUSE BOX - FOR CC JUMP, I put other wire next to the blue one and it lunges at me.
CTScottUSA, CT · May 28, 2010#236
Even if the switches are NC instead of NO, it shouldn't try to start. I see you are using a piece of bare wire. Are you sure it is only making contact with the blue and white wires?

By the way, the violet wire between the blue and white is the output to the starter, so making contact with it would indeed crank the starter.

Also, your Sedan is MT, not AT?
sk8manmikeCO · May 28, 2010#237
MT - i'm pretty sure i've only been touching the blue wire - i made the wire have a lot of bare wire so that i can check the voltage easier
CTScottUSA, CT · May 28, 2010#238
Originally Posted by sk8manmike ↑
MT - i'm pretty sure i've only been touching the blue wire - i made the wire have a lot of bare wire so that i can check the voltage easier
Everything looks correct. I would make your connections with the ignition off (and perhaps the battery disconnected as well). Then, carefully connect the battery / turn the ignition on.
sk8manmikeCO · May 28, 2010#239
I can't seem to produce any Volts between the connection anymore - it took me awhile to get the previous ones too. I'm pretty sure that the connection is whats keeping my CC from working.

Any idea who sells T Splice or something similiar? I'd hate to have to buy it from Amazon and wait another week.
CTScottUSA, CT · May 28, 2010#240
Originally Posted by sk8manmike ↑
I can't seem to produce any Volts between the connection anymore - it took me awhile to get the previous ones too. I'm pretty sure that the connection is whats keeping my CC from working.

Any idea who sells T Splice or something similiar? I'd hate to have to buy it from Amazon and wait another week.
Radio shack and most auto parts stores sell them.

Also, to make sure your switches are correct; If you measure the voltage between the two terminals of the first switch, with the ignition on, you should see 12 volts. If you see zero, then your switches are normally closed, instead of normally open.
sk8manmikeCO · May 28, 2010#241
I'm not getting any voltage on the first switch.

This the switch for all four spots: http://www.radioshack.com/product/in...ductId=2062543

One of the reviews states that besides being crappy switches, they have a habit of going to a closed states when worn.
sk8manmikeCO · May 29, 2010#242
I'm using 22 Gauge Wire - is that what gauge T Splice I should get? I'm not sure what gauge wire runs to the fuse box.
CTScottUSA, CT · May 29, 2010#243
Originally Posted by sk8manmike ↑
I'm using 22 Gauge Wire - is that what gauge T Splice I should get? I'm not sure what gauge wire runs to the fuse box.
It's somewhere between 18 and 20 gauge I believe. The tap splices are usually good for a range, so if you can get 22 to 18 gauge ones you'll be fine.

For the no voltage on the switch, measure the red wire to ground (with the ignition on). If that is still zero, then disconnect it from the switch and measure the red wire separately to ground. If it is still zero, than your ECM pin is not properly seated.
sk8manmikeCO · May 29, 2010#244
Nice - My Terminal in the ECM wasn't completely seated - looking back at my first pic you can clearly tell that its only partly in. I have voltage now going to my switch and i'm going to do the jump and pick up some T Splice afterwards.
sk8manmikeCO · May 29, 2010#245
Yay! It works......Thank you for constantly moderating this thread CTScott - it's good to know that when you attempt mods on this site your not doing it alone.
YarisduderMontreal, Canada · Jun 7, 2010#246
Hello,

I just put in an OEM Cruise stalk to replace my little 2 button diy one and I made a discovery regarding the $30 toyota cruise wire. The pins that go into the horn connector as well as connector D3 seem to be the same as those for an R/C servo, example:

Picture lost · www.servocity.com

It's a little finicky to get them into the white plugs, especially D3 which I discovered has a lock you have to loosen with a tiny flat thing. I don't know if these will work with pin 40. As a bonus the servo connector also fits into the OEM cruise stalk, though its pin spacing is a little wider so it bends the contacts a little, and there's no locking mechanism so I guess it could vibrate loose, though mine feels pretty firmly seated.

Happy DIYing!
firemachine69Sudbury, On · Jul 11, 2010#247
Sorry to revive this thread here folks, but on a CAD Yaris auto LB (2007), I need the OE Toyota stalk, and the pin-40?

I read the the instructions of Sparks, and no mention is made requiring the pin-40 mod... Therefore, I am a bit lost. 😁
CTScottUSA, CT · Jul 11, 2010#248
Originally Posted by firemachine69 ↑
Sorry to revive this thread here folks, but on a CAD Yaris auto LB (2007), I need the OE Toyota stalk, and the pin-40?

I read the the instructions of Sparks, and no mention is made requiring the pin-40 mod... Therefore, I am a bit lost. 😁

On an 07 you will need to add the wiring from the stalk connector to the ECM pin 40:

DIY Cruise Control FAQ (2006-2010 Yaris)
firemachine69Sudbury, On · Jul 12, 2010#249
Thanks Scott.

Looked at the Sparks list, apparently it wouldn't be required. Considering my shipping is the cost of the wire, I'd be pretty pissed off if I had to do two separate orders because of their innacurate instructions! 😠
darkMINIC-Springs · Jul 13, 2010#250
Using the toyota stalk I got from salvage yard on the column, in an '08 MT, is the wiring already in the column for the switch to connect to or would I have to mount this switch stalk elsewhere?