Yarisworld Archive

DIY Cruise Control on 07-08 Yaris (step by step)

415 posts · 355,617 views · page 3 of 9

Replies continued

rtomDenver, CO · Jan 29, 2010#101
Thanks! That's a pretty efficient start.

I'm a good guinea pig because I'm planning to do this (well, when the weather warms up -- I don't have a garage). From my point of view, the next steps are to nail down (1) part numbers and sources, and (2) procedures and tools required. Probably it's not so hard to summarize part numbers & sources, but summarizing procedures might be trickier?

Anyway, thanks, and I'll start reading the threads.
Sodium DuckWestern Mass. · Jan 30, 2010#102
Should we be disconnecting the battery when playing with the ECU?
CTScottUSA, CT · Jan 30, 2010#103
Originally Posted by Sodium Duck ↑
Should we be disconnecting the battery when you play with the ECU?
It would be a good idea to do so.
Sodium DuckWestern Mass. · Jan 30, 2010#104
Here's how I did mine. I wanted to be able to easily see and use the cruise control. To the left of the steering was too low for me, and the spot on the right isn't visible to me.

If you can't tell, this is the armrest piece with the power window/lock controls. The back of this plastic actually has two round raised things that I used as guides -- didn't even have to measure it out, just drilled the holes and wired it up. The red is on, black is set. Will also use the slide connects in the background just in case I ever need to remove the door panel. It goes in tomorrow, too dark out right now to be rooting around under the hood.
DSC05692.jpg
Sodium DuckWestern Mass. · Jan 31, 2010#105
Works great! Thanks to all who put this DIY together.
Sodium DuckWestern Mass. · Feb 2, 2010#106
The cockpit:
Cruise controls to my left.
CB, aftermarket stereo, 2009 black knurled control knobs, Ecometer and painted flat black trim to my right.

I love my Yaris.

If anyone wants my leftover resistors, I'll mail them to you, just PM me. I have 4 (comes in a pack of five).
DSC05694.jpgDSC05704.jpg
Sodium DuckWestern Mass. · Feb 2, 2010#107
Resistors are gone.
rcspottBozeman MT · Feb 3, 2010#108
2008 HB 3 Door Yaris Qustion

How much of the dash do you have to remove to see these connectors? Are some of them under the hood?

Thanks
CTScottUSA, CT · Feb 3, 2010#109
Originally Posted by rcspott ↑
2008 HB 3 Door Yaris Qustion

How much of the dash do you have to remove to see these connectors? Are some of them under the hood?

Thanks
Check out this thread:

DIY Cruise Control FAQ (2006-2010 Yaris)
kazama82Malaysia · Feb 7, 2010#110
a quick question...will this work with yaris malaysia (in Malaysia, we call Toyota VIOS)
CTScottUSA, CT · Feb 7, 2010#111
Originally Posted by kazama82 ↑
a quick question...will this work with yaris malaysia (in Malaysia, we call Toyota VIOS)
I don't believe so. The way to test if it might is to measure the voltage on pin 40 of the ECM connector A21 (the pin where the cruise switch connects to). If that pin measures 12 V with the ignition on, then it might work. If it doesn't, then your ECM doesn't have the cruise control functionality built in.
kazama82Malaysia · Feb 7, 2010#112
thanks scott..will try and measure..if it does have, i can do the wiring as stated.?..will the indicator shows at the meter panel?..
CTScottUSA, CT · Feb 7, 2010#113
Originally Posted by kazama82 ↑
thanks scott..will try and measure..if it does have, i can do the wiring as stated.?..will the indicator shows at the meter panel?..
If it does have it, then you can do the wiring as above. For the indicator, you can shine a flashlight on the panel to see what indicators are there, and if the cruise ones are.
FalconeerDubai · Feb 10, 2010#114
If I got the Toyota Stalk from ebay, do I just wire it directly to the ECU or does it need the resistors as well?
CTScottUSA, CT · Feb 10, 2010#115
Originally Posted by Falconeer ↑
If I got the Toyota Stalk from ebay, do I just wire it directly to the ECU or does it need the resistors as well?
Directly to the ECM. The resistors emulate what is inside of the stalk.

I don't believe that your Yaris will have the cruise control functionality, as thus far it seems to only be US and Canada Yaris that do. To check before talking your steering wheel apart, measure the voltage on the ECM pin with the ignition on. If the pin doesn't measure 12V, then the stalk won't work.
frankencarsherwood, oregon · Feb 13, 2010#116
Hey guys, I need help! I just spent the afternoon putting in the two-button diy cruise with CTScott's indicator module...seemed like the install went pretty smooth, but it's not working! When I start the car, the indicator light goes on, then off for a quick moment, and then stays on. What could that mean?

I used two buttons (the black radio shack ones) and three 220 Ohm, 1/4 watt resistors in series, for 660 Ohm...should be right in the range, yes?

My first thought is that it is the ECM connection. I ordered the original factory part, Toyota repair terminal, or whatever it's called, and I had a heck of a time putting that thing in. My main problem is that it was a square peg going into a square hole, but first going through a round hole....It was very difficult to line up, and I gently played with it until I got the most secure fit I could, but I'm still not convinced it's in all the way.

Any thoughts?
CTScottUSA, CT · Feb 13, 2010#117
Originally Posted by frankencar ↑
Hey guys, I need help! I just spent the afternoon putting in the two-button diy cruise with CTScott's indicator module...seemed like the install went pretty smooth, but it's not working! When I start the car, the indicator light goes on, then off for a quick moment, and then stays on. What could that mean?

I used two buttons (the black radio shack ones) and three 220 Ohm, 1/4 watt resistors in series, for 660 Ohm...should be right in the range, yes?

My first thought is that it is the ECM connection. I ordered the original factory part, Toyota repair terminal, or whatever it's called, and I had a heck of a time putting that thing in. My main problem is that it was a square peg going into a square hole, but first going through a round hole....It was very difficult to line up, and I gently played with it until I got the most secure fit I could, but I'm still not convinced it's in all the way.

Any thoughts?
The light staying on indicates that the indicator module is seeing the switch wire being shorted to ground.

For getting the pin in, did you pop the orange thing on the side of the connector, which is the retainer for the pins?
FalconeerDubai · Feb 14, 2010#118
CTScott.. I am aware of that and was planning on checking that soon. I have a rental Yaris I can experiment on at the moment!!
Mine gets delivered on the 24th.
rcspottBozeman MT · Feb 16, 2010#119
Have all the parts to do a 2 button cruise on a 08 Yaris HB MT. Couple of questions/confidence builder...

What kind of connector are you using for the clutch control switch wires were they are connected in the fuse box?

Getting the wires through the firewall seems like the biggest challenge.

Where is the grommet on the passenger side, what color is it, any information of what you have to remove to see this grommet would be extremely helpful.

The hood release method, what do you have to remove to go that route? The plastic in the wheel well, does that need to be removed?

Do you wrap these wires in electrical tape?

I'm a real rookie at this, any tips would be greatly appreciated.

Thanks,

Rich
Sodium DuckWestern Mass. · Feb 16, 2010#120
"Where is the grommet on the passenger side, what color is it, any information of what you have to remove to see this grommet would be extremely helpful."

This was so annoying for me. I found it easiest to go under the hood and get it from there. Look at the ECU, the grommet is to the right. It's black, like an inch or so wide. I popped mine out, and pushed a sharp piece of metal at the carpet behind. Then I went back in the car, saw where the metal was and cut an X in it. Ran the wire through and was done. I don't know why it took so long...
rcspottBozeman MT · Feb 18, 2010#121
Sodium Duck,

I want to verify that the ECU Box is alumimun with the two wire plugs on top and is all mounted to the fire wall on the left as your looking in from the front of the car. OK

I looked to the right of the ECU box and see no black grommet. All I see is a round grommet right at the left top corner of the ECU box.

This is giving me fits, any help out there, Picture?

Thanks

Rich
Sodium DuckWestern Mass. · Feb 18, 2010#122
That's the grommet I'm talking about, you got it.
rcspottBozeman MT · Feb 20, 2010#123
Thank you "all that came before me", another successful cruise control install here. It's going to make my drive next week from Montana to California a breeze. Thanks again Sodium Duck for the resistors. I have left over resistors, if anyone wants them PM me and I will mail them off to you. They are the 680's that work perfectly for the two button install.

Thanks

Rich
rcspottBozeman MT · Feb 20, 2010#124
Resistors are gone.
Sodium DuckWestern Mass. · Feb 21, 2010#125
Sending resistors all over the place is fun.
frankencarsherwood, oregon · Mar 6, 2010#126
Still having a massive failure. Anybody who's done this in the Portland metro area? It's really hard to figure out what's going on via forum X.X

Popped the ECU white thing, seems like I got a pretty tight fit, though the rubber still sticks up a bit (but its also kind of chewed up). The connector seems to be in perfect shape, I was really careful not to bend it, it is a $20 pin for crying out loud.

What else could it be?!
CTScottUSA, CT · Mar 6, 2010#127
Originally Posted by frankencar ↑
Still having a massive failure. Anybody who's done this in the Portland metro area? It's really hard to figure out what's going on via forum X.X

Popped the ECU white thing, seems like I got a pretty tight fit, though the rubber still sticks up a bit (but its also kind of chewed up). The connector seems to be in perfect shape, I was really careful not to bend it, it is a $20 pin for crying out loud.

What else could it be?!

Did you ever take a voltage reading on the other end of the wire connecting to that pin? With the ignition on and engine not running, that wire should measure ~12 Volts to ground. If you don't measure that, then there is still an issue with connecting to that pin on the ECM.
frankencarsherwood, oregon · Mar 6, 2010#128
UPDATE: VICTORY!!!

Okay okay, it was something DUMB...

One of my wires snapped within the electrical tape wrapping. Not sure exactly how that happened, I must have pulled on the other end. Anyway, just got back from a successful test run. Beautiful, I love it!!!!

Thanks CTScott and others for finding this amazing mod!
goat1of2USA · Mar 9, 2010#129
And yet *another* new Yaris owner gives this a try......

It seems that y'all are saying that we should disconnect the battery before pulling off ECM connector A21. Yet, won't I need the battery connected to check if 12V is present at pin 40? That's right, I've never messed with the electronics in a car before.

Also, I'm looking at the document so kindly provided by Vince87 and I cannot for the life of me find Connector D3 either. I have a very late model 2008 and wanted to make sure that the wires I need aren't already in the cabin. There's a whole passel of connectors under that dash, most of which I cannot see because of all the plastic covers. Do I need to remove some of them?
CTScottUSA, CT · Mar 9, 2010#130
Originally Posted by goat1of2 ↑
And yet *another* new Yaris owner gives this a try......

It seems that y'all are saying that we should disconnect the battery before pulling off ECM connector A21. Yet, won't I need the battery connected to check if 12V is present at pin 40? That's right, I've never messed with the electronics in a car before.

Also, I'm looking at the document so kindly provided by Vince87 and I cannot for the life of me find Connector D3 either. I have a very late model 2008 and wanted to make sure that the wires I need aren't already in the cabin. There's a whole passel of connectors under that dash, most of which I cannot see because of all the plastic covers. Do I need to remove some of them?

Check out this link for a comprehensive list of links related to installing cruise control:

DIY Cruise Control FAQ (2006-2010 Yaris)

This picture from my 09+ DIY shows D3 (the leftmost connector with the brown, blue and black wires):



You need to remove the lower steering column cover to gain access to it.

As far as disconnecting the battery goes, you should do so while doing the wiring to the ECM. Checking for 12V on pin 40 is really only necessary if you have issues with it not working, and in that case, you'd measure the voltage at that pin via the wire that you connected to it.
goat1of2USA · Mar 9, 2010#131
Originally Posted by CTScott ↑
You need to remove the lower steering column cover to gain access to it.

As far as disconnecting the battery goes, you should do so while doing the wiring to the ECM. Checking for 12V on pin 40 is really only necessary if you have issues with it not working, and in that case, you'd measure the voltage at that pin via the wire that you connected to it.
Thank you sir. I found my Connector D3 and confirmed that I will need to run a wire from the ECM. Now to order the parts....

Perhaps the language in the pdf should be amended to read: "...connector D3 on the left side of the steering column (under the plastic housing)". I was taking "under the dash" to mean well, under the dash!

In case anyone finds it useful, the build date for my Yaris was May 2008; apparently they were not yet incorporating any features from the 2009 cruise control setup yet!
lilyMN · Mar 10, 2010#132
I need some help from this install.

Got an '07 Yaris HB, base model, auto.

I did the 2 button setep from CTScott's PDF write-up.

I cannot get the 'cruise' to work after this mod.

What I did was soldered two resistors in series: a 270 and 380 for a 650 resistor. Then soldered the series as shown on the PDF for the 2 button setup.

I ran a wire to the PIN 40 on the ECU and grounded the other wire, but still nothing.

My questions are:

How far does the wire going into the ECU have to "stick" out to touch inside the ECU?........I have maybe 2 or 3 wires that stuck out from the harness, is that enough "contact" to make this work?

I grounded the other wire by just screwing/sandwiching into a grounded source on the driver's kick panel, <<< is this "good grounding"???

Is soldering a good idea to connect the series? <<< I soldered because the pins behind on the push buttons I got from Radio Shack were too small to work on.

I hope I am clear about my questions. It has been raining here so I would like some help soon so I could use this feature on my upcoming road-trip.

Thank you for your time.
CTScottUSA, CT · Mar 10, 2010#133
Originally Posted by lily ↑
I need some help from this install.

Got an '07 Yaris HB, base model, auto.

I did the 2 button setep from CTScott's PDF write-up.

I cannot get the 'cruise' to work after this mod.

What I did was soldered two resistors in series: a 270 and 380 for a 650 resistor. Then soldered the series as shown on the PDF for the 2 button setup.

I ran a wire to the PIN 40 on the ECU and grounded the other wire, but still nothing.

My questions are:

How far does the wire going into the ECU have to "stick" out to touch inside the ECU?........I have maybe 2 or 3 wires that stuck out from the harness, is that enough "contact" to make this work?

I grounded the other wire by just screwing/sandwiching into a grounded source on the driver's kick panel, <<< is this "good grounding"???

Is soldering a good idea to connect the series? <<< I soldered because the pins behind on the push buttons I got from Radio Shack were too small to work on.

I hope I am clear about my questions. It has been raining here so I would like some help soon so I could use this feature on my upcoming road-trip.

Thank you for your time.

You really need to have good connection to the ECM pin and realllllly want it to still be waterproof, so using one of the correct pins for the connector is a good idea.

Soldering the resistors is definitely the way to go. In the example pictures of the two switch methods I just put them together to show the layout, but didn't solder the examples.
lilyMN · Mar 10, 2010#134
how would the connection pin to the ECM look like?

i may have some extra pins left from the tacoma.
CTScottUSA, CT · Mar 10, 2010#135
Originally Posted by lily ↑
how would the connection pin to the ECM look like?

i may have some extra pins left from the tacoma.
ECM Pin.jpg
lilyMN · Mar 11, 2010#136
well, i re-wired new push buttons and added a new single 620 resistor to the 2-button setup but still no avail.

i'm thinking that the connection to PIN 40 is not so good.

how did you all establish "connection" to this PIN 40?

did you just simply push a strand of wire through the harness or actually got one of those little pins? (i just pushed a wire through the harness because i cannot figure out how to completly disassemble it).

can the head piece of harness be taken apart further? <<< i have take it off the ECU/ECM and the taken the little rubber plug off but cannot figure out if the head piece of the harness can be taken apart further.

Thank you.
goat1of2USA · Mar 11, 2010#137
Originally Posted by CTScott ↑

Soldering the resistors is definitely the way to go. In the example pictures of the two switch methods I just put them together to show the layout, but didn't solder the examples.
Ah ha! I was wondering about that. This is like when we women give recipes by just mentioning a few ingredients...there are a whole LOT of steps which are simply assumed. As more inexperienced people like myself attempt this mod, you'll be getting all kinds of seemingly "dumb" questions. Like this one:

I've got some AWG 20 wire, but it is single-strand copper instead of the multi-strand silver-looking stuff I see all you guys used. Will this work? Can I solder it? Will it corrode if mixed with whatever other metals are involved?

See what I mean?

[Project status: resistors and switches on order from Digikey, proper ECM connector on order from Toyota]
fratzicaBucharest · Mar 15, 2010#138
do you have any idea if this tutorial works on european Yaris models? Or if not, could you direct me to one? Thank you!
CTScottUSA, CT · Mar 15, 2010#139
Originally Posted by fratzica ↑
do you have any idea if this tutorial works on european Yaris models? Or if not, could you direct me to one? Thank you!
It does not work on European Yaris, as they don't have the cruise control functionality built into the ECM. To add cruise control you would need to purchase an expensive aftermarket kit (I believe people have mentioned it to be about $800 USD).
fratzicaBucharest · Mar 15, 2010#140
wow that`s expensive 🙁
Did you also check the diesel European models, or just the gasoline powered ones?
Thank you for your quick answer.
CTScottUSA, CT · Mar 15, 2010#141
Originally Posted by fratzica ↑
wow that`s expensive 🙁
Did you also check the diesel European models, or just the gasoline powered ones?
Thank you for your quick answer.
Both do not.
goat1of2USA · Mar 15, 2010#142
Well, as you can probably tell from the stupid questions I was asking, this mod was way way beyond me. I have now broken a part and am wondering if you would identify which Toyota part number it is (where do you find these numbers?)

It is the plastic locking lever which locks in and holds connector A21. Picture enclosed.

Also, I did another stupid thing which seemed smart at the time: I pushed the plug over Pin 40 down through the connector. Of course it didn't come out the other side. I was supposed to pull it OUT! Stupid stupid. Now my special 20.00 connnector orderd from Toyota will not seat. Any suggestions? Other than just shooting myself now.
DSCN1492.jpg
CTScottUSA, CT · Mar 15, 2010#143
Originally Posted by goat1of2 ↑
Well, as you can probably tell from the stupid questions I was asking, this mod was way way beyond me. I have now broken a part and am wondering if you would identify which Toyota part number it is (where do you find these numbers?)

It is the plastic locking lever which locks in and holds connector A21. Picture enclosed.

Also, I did another stupid thing which seemed smart at the time: I pushed the plug over Pin 40 down through the connector. Of course it didn't come out the other side. I was supposed to pull it OUT! Stupid stupid. Now my special 20.00 connnector orderd from Toyota will not seat. Any suggestions? Other than just shooting myself now.
Yikes!

I don't see the locking lever listed anywhere in the EPC, so for that one you'll have to check with the parts person at your local dealer to see if it can be purchased (otherwise you might have to try to find one at a junkyard).

for getting that rubber plug back out, try pushing it from the pin side. If that doesn't work, you might be able to pull it out the wire side using a sewing pin with the tip bent into a hook.
goat1of2USA · Mar 15, 2010#144
There is a part number on the lever but it says "Tyco 90980-12589"

Tried googling it but nothing yet.
CTScottUSA, CT · Mar 15, 2010#145
Originally Posted by goat1of2 ↑
There is a part number on the lever but it says "Tyco 90980-12589"

Tried googling it but nothing yet.

Tyco, Sumitomo, etc. make many custom connectors for Toyota, which you can't purchase from anyone, except the manufacturer or Toyota.
Sodium DuckWestern Mass. · Mar 15, 2010#146
I also did that with the rubber thing in the connector, too. Just take a needle and push it back out the right way, it'll go. I had a lot of trouble too with that stupid connector. That black sliding piece wouldn't go back on, and after 10 minutes of fudging around with it, I just took it off and put the gray piece back on and slid it into place.

Don't worry - your car is not dead.
goat1of2USA · Mar 16, 2010#147
Originally Posted by Sodium Duck ↑
I also did that with the rubber thing in the connector, too. Just take a needle and push it back out the right way, it'll go. I had a lot of trouble too with that stupid connector. That black sliding piece wouldn't go back on, and after 10 minutes of fudging around with it, I just took it off and put the gray piece back on and slid it into place.

Don't worry - your car is not dead.
Thank you, Mr (or Ms) Duck, for your kind words of sympathy. The boyfriend came home after work and somehow managed to reinstall the piece I'd broken and superglued back together. Car now runs. PHEW! Back to square one.

He tried for quite some time to work out that plug using a pin, a thicker piece of wire, and just some general cussing. He says he can see the plug down in there and it is kind of sideways, allowing a wire to go right through to the other side, without piercing the plug.

He wants to use a tiny drill bit and DRILL the plug to bits. I say we don't know what the heck is inside that connection hole, so we risk ruining a 500.00 component! We might just smear the material the plug is made of all up inside there, making a worse mess. We might somehow screw up the neighboring connector, which has a wire already in it.

I want to try leaving the plug in and just pushing a single-strand AWG 20 wire through the connector and seeing if THAT will make a good-enough connection. A wire of that description does go right through.

So, do we try it his way or my way? Or, do I just cover the hole left by the missing plug with electrical tape and pronounce this vehicle PERMANENTLY WITHOUT CRUISE CONTROL.

I hope at least you all are getting a good laugh out of this!
CTScottUSA, CT · Mar 16, 2010#148
Originally Posted by goat1of2 ↑
Thank you, Mr (or Ms) Duck, for your kind words of sympathy. The boyfriend came home after work and somehow managed to reinstall the piece I'd broken and superglued back together. Car now runs. PHEW! Back to square one.

He tried for quite some time to work out that plug using a pin, a thicker piece of wire, and just some general cussing. He says he can see the plug down in there and it is kind of sideways, allowing a wire to go right through to the other side, without piercing the plug.

He wants to use a tiny drill bit and DRILL the plug to bits. I say we don't know what the heck is inside that connection hole, so we risk ruining a 500.00 component! We might just smear the material the plug is made of all up inside there, making a worse mess. We might somehow screw up the neighboring connector, which has a wire already in it.

I want to try leaving the plug in and just pushing a single-strand AWG 20 wire through the connector and seeing if THAT will make a good-enough connection. A wire of that description does go right through.

So, do we try it his way or my way? Or, do I just cover the hole left by the missing plug with electrical tape and pronounce this vehicle PERMANENTLY WITHOUT CRUISE CONTROL.

I hope at least you all are getting a good laugh out of this!

I would avoid the drill bit route, as that has the potential to do unnecessary damage. The cavity that the plug is stuck in is rectangular, so it is fairly easy to have it round plug end of sideways in there. The drill bit will probably just chew up the soft sides of the cavity, rather than the plug. The key with the plug being wedged is to get something to hook deep enough into the plug to allow it to be pulled.
rcspottBozeman MT · Mar 16, 2010#149
Goat,

You have a Private Message
lilyMN · Mar 16, 2010#150
Originally Posted by lily ↑
well, i re-wired new push buttons and added a new single 620 resistor to the 2-button setup but still no avail.

i'm thinking that the connection to PIN 40 is not so good.

how did you all establish "connection" to this PIN 40?

did you just simply push a strand of wire through the harness or actually got one of those little pins? (i just pushed a wire through the harness because i cannot figure out how to completly disassemble it).

can the head piece of harness be taken apart further? <<< i have take it off the ECU/ECM and the taken the little rubber plug off but cannot figure out if the head piece of the harness can be taken apart further.

Thank you.
well, still no cruise yet.

my main question is about how to take off the ECU harness.

i have gone as far as "unlocking" the harness via the "white clip" like the pictures from the previous posts.

but does the harness come off even further??? <<< can someone please take a pic of the "full breakdown" of the harness???

what i did was pretty much just "unlocked" the harness via the "white clip" and slid a wire through PIN 40. <<< this i believe somehow is not "good enough" contact to the ECU itself.

i think this is what I'm stuck on, because i cannot establish a good contact from the wire to the ECU. i have the little connector pin, but just don't know how to break down the ECU harness to fit it onto PIN 40 of the harness.

HELP PLEASE.