Yarisworld Archive

DIY Cruise Control on 07-08 Yaris (step by step)

415 posts · 355,617 views · page 8 of 9

Replies continued

i-transMontréal, Québec · Jul 10, 2011#351
and this cruise control have a fuse anywhere, in case of shortcut ??
what's happen if utilise N.C switch for testing purpose?
in exemple the first switch are N.C (pin 40 to this switch) , and for the second switch i utilize an N.O switch?
the n.c switch when i push on it its "ON" when i repress on it its "off".
and the second switch its "set"
CTScottUSA, CT · Jul 10, 2011#352
Originally Posted by i-trans ↑
and this cruise control have a fuse anywhere, in case of shortcut ??
what's happen if utilise N.C switch for testing purpose?
in exemple the first switch are N.C (pin 40 to this switch) , and for the second switch i utilize an N.O switch?
the n.c switch when i push on it its "ON" when i repress on it its "off".
and the second switch its "set"
No fuse - This is just an analog input to the ECM.

A NC switch won't work. The ECM expects to see the input float and then get pulled down to a specific voltage range for it to register. I have reverse engineered the Toyota diagnostics CAN Bus comm to read the cruise control switch state from the ECM, so I can watch how the ECM responds to the inputs.

Have you measured your resistors to see exactly what they read resistance wise. Sometimes you can get a batch that are really at the end of their tolerance band.
i-transMontréal, Québec · Jul 10, 2011#353
i don't know what is the way to test resistors...
12v on a side of the resistor and read the other side?
CTScottUSA, CT · Jul 10, 2011#354
Originally Posted by i-trans ↑
i don't know what is the way to test resistors...
12v on a side of the resistor and read the other side?
Resistance setting on the multimeter. Measure with no voltage applied.
i-transMontréal, Québec · Jul 17, 2011#355
My problem was resolved!!!
My cruise control are fully functionnal!!!

My problem was my resistor....
on the package it was write 390 ohm 1/4 watt, but in reality it was 390k Ohm 1/4 watts...

Thanks you CTScott for you're help!
rob1005Ontario, Canada · Sep 27, 2011#356
I just purchased the clutch switch from Toyota but it did not include any connector or wires. It just has two prongs. How would I go about attaching two wires to the prongs?

Toyota also gave me screws which are too big for the cruise stalk. Which screws do I need?

Thanks for all your help.
CTScottUSA, CT · Sep 27, 2011#357
Originally Posted by rob1005 ↑
I just purchased the clutch switch from Toyota but it did not include any connector or wires. It just has two prongs. How would I go about attaching two wires to the prongs?

Toyota also gave me screws which are too big for the cruise stalk. Which screws do I need?

Thanks for all your help.
On the clutch switched that I ship to people with 06-08's, I solder wires to the two pins and then individually heat shrink them, and then heat shrink over both as a strain relief. You could also use some very small female spade terminals, if you are not comfortable with soldering to them.

The screws are M5-.80
packetraceQuebec · Sep 27, 2011#358
Is there a DIY on how to remove the steering wheel and the airnag ?
packetraceQuebec · Sep 27, 2011#360
So...I unscrew the 2 side screw..and I pull the whole steering wheel...and It will pop off ?

OBVIOUSLY i disconnect the battery hahaha!
CTScottUSA, CT · Sep 27, 2011#361
Originally Posted by packetrace ↑
So...I unscrew the 2 side screw..and I pull the whole steering wheel...and It will pop off ?

OBVIOUSLY i disconnect the battery hahaha!
Section 1, specifically 1.1.1...
packetraceQuebec · Sep 27, 2011#362
Yes I know..but I mean...I pull on the whole steering wheel...or only the middle part where there is the toyota emblem ?
CTScottUSA, CT · Sep 27, 2011#363
Originally Posted by packetrace ↑
Yes I know..but I mean...I pull on the whole steering wheel...or only the middle part where there is the toyota emblem ?
You are only removing the airbag (which is the center portion of the steering wheel), unless you wish to drill the lower steering wheel cover off of the car, or are replacing it with a pre-holed one.
rob1005Ontario, Canada · Oct 2, 2011#364
Just finished installing and works perfectly. Wish the 07s had a cruise light on the dash though. Oh well, thanks for the good DIY Scott.

I was wondering how you managed to feed the clutch switch wires through the firewall. I gave up because of limited space and just fed the wires back through the passenger side grommet.
CTScottUSA, CT · Oct 2, 2011#365
Originally Posted by rob1005 ↑
Just finished installing and works perfectly. Wish the 07s had a cruise light on the dash though. Oh well, thanks for the good DIY Scott.

I was wondering how you managed to feed the clutch switch wires through the firewall. I gave up because of limited space and just fed the wires back through the passenger side grommet.
With the giant grommet on the driver's side, where the main cable harness goes through, there are two small nipples that you can poke through. You have to first go through with something sharp, and then the wire will feed through.
RatzSidney, BC · Oct 16, 2011#366
For DIY cruise control

When drilling 1-1/8” opening in the steering wheel trim/cover, I used small square of black winds surfing jacket neoprene (just to cover up guts of the switch) and then used sliced windshield washer hose to finish the edge. What can I say , my wife’s attention to details is admirable.

Picture lost · www3.telus.net
scapeBeaufort, South Carolina · Dec 5, 2011#367
Originally Posted by Vince87 ↑
Hi all ! as promised in the other thread, here's a Step by Step DIY for the Cruise Control installation (swith method) on 07-08 liftback Yaris (should be pretty similar on the sedan)...

I just to say a special thanks to CTScott for the discovery, the instructions and for his help through the process and also to nickhjort for being the guinea pig for this model.

Enjoy !
Great, quick read. I have question, is the clutch switch just necessary if you do not want the engine to rev out during gear changes while the CC is engaged? I am planning a 1600 mile trip and don't know if I have time to purchase the clutch switch ass.

What kind of wire is necessary, I have a radioshack and a homeimprovement store nearby (and a wallyworld,) I don't know if any of them sell durable wiring-- maybe the home improvement store for inwall wiring.

Did your radioshack, local parts store actually carry resistors?

Any advice from someone who has completed the install is great!

Thanks :)
CTScottUSA, CT · Dec 5, 2011#368
Originally Posted by scape ↑
Great, quick read. I have question, is the clutch switch just necessary if you do not want the engine to rev out during gear changes while the CC is engaged? I am planning a 1600 mile trip and don't know if I have time to purchase the clutch switch ass.

What kind of wire is necessary, I have a radioshack and a homeimprovement store nearby (and a wallyworld,) I don't know if any of them sell durable wiring-- maybe the home improvement store for inwall wiring.

Did your radioshack, local parts store actually carry resistors?

Any advice from someone who has completed the install is great!

Thanks :)

The clutch switch can be bypassed, but it's pretty easy to forget and touch the clutch while in cruise control mode.

For the wire, any stranded 18 to 20 AWG wire is fine.

Radioshack will probably have the resistors as part of a multipack.

If you want to do the OEM stalk method I have all of the parts (stalk, clutch switch, ECM pin, etc.) on hand and can ship overnight or two day if you need them quickly. Here's the link to my DIY for the OEM stalk method:

DIY: 2006-2011 Yaris OEM Cruise Control Complete Installation
scapeBeaufort, South Carolina · Dec 5, 2011#369
Originally Posted by CTScott ↑
The clutch switch can be bypassed, but it's pretty easy to forget and touch the clutch while in cruise control mode.

For the wire, any stranded 18 to 20 AWG wire is fine.

Radioshack will probably have the resistors as part of a multipack.

If you want to do the OEM stalk method I have all of the parts (stalk, clutch switch, ECM pin, etc.) on hand and can ship overnight or two day if you need them quickly. Here's the link to my DIY for the OEM stalk method:

DIY: 2006-2011 Yaris OEM Cruise Control Complete Installation
thanks for the package deal :) but I think i'll wait on the stalk, not sure if I want to spend so much on that yet, nor do I want to dive in to changing the steering wheel stuff so close to my trip. I think I'll hit up radioshack today for the resistors. I have some extra 18awg speaker wire I guess I'll test out unless you suggest not to?
for the jumper, should I just drop in the wire and solder it to the correct locations. I'll probably eventually get the clutch switch but I just want to be able to turn it on and off really, for now.

out of curiosity how much is your kit? :)

oh yeah, from past experience: does braking automatically disengage the CC (since it is ECU i would say yes)?

thanks for the quick reply
CTScottUSA, CT · Dec 5, 2011#370
Originally Posted by scape ↑
thanks for the package deal :) but I think i'll wait on the stalk, not sure if I want to spend so much on that yet, nor do I want to dive in to changing the steering wheel stuff so close to my trip. I think I'll hit up radioshack today for the resistors. I have some extra 18awg speaker wire I guess I'll test out unless you suggest not to?
for the jumper, should I just drop in the wire and solder it to the correct locations. I'll probably eventually get the clutch switch but I just want to be able to turn it on and off really, for now.

out of curiosity how much is your kit? :)

oh yeah, from past experience: does braking automatically disengage the CC (since it is ECU i would say yes)?

thanks for the quick reply

For the temporary clutch switch bypass, you can either solder in a jumper or find a small male spade that will fit tightly into the connector along side of the pin.

Kit pricing:

CC Stalk with wiring and mounting screws: $40
ECM connector pin: $5
Connector D3 pins: $5
MT CC clutch switch: $15
scapeBeaufort, South Carolina · Dec 9, 2011#371
quick question on those momentary switches: I found a few at radioshack but they are low-amp rated (like .5A).. I noticed the referenced digikey switches are around 3 amps. what's the max rated amperage I should shoot for?

i found a few packs of resistors at the local radioshack, but none at 240. looks like i'll be soldering them together to make 240. they're rated at 5% tolerance, if combining them would the tolerance inherently go up?
CTScottUSA, CT · Dec 9, 2011#372
Originally Posted by scape ↑
quick question on those momentary switches: I found a few at radioshack but they are low-amp rated (like .5A).. I noticed the referenced digikey switches are around 3 amps. what's the max rated amperage I should shoot for?

i found a few packs of resistors at the local radioshack, but none at 240. looks like i'll be soldering them together to make 240. they're rated at 5% tolerance, if combining them would the tolerance inherently go up?
Any momentary switch is fine. You are switching an analog input to a microcontroller, so the current is negligible.

For the resistors the tolerance means how far they can be off, so a 100 ohm, 5% can be 95 to 105 ohms. Since it is a plus or minus rating, chaining them together means that they can cancel each other out, or add to the percentage off in either direction. If you have a multimeter, you can measure the actual resistance of each.
scapeBeaufort, South Carolina · Dec 9, 2011#373
Originally Posted by CTScott ↑
Any momentary switch is fine. You are switching an analog input to a microcontroller, so the current is negligible.

For the resistors the tolerance means how far they can be off, so a 100 ohm, 5% can be 95 to 105 ohms. Since it is a plus or minus rating, chaining them together means that they can cancel each other out, or add to the percentage off in either direction. If you have a multimeter, you can measure the actual resistance of each.
thx for the quick reply. what then would be the permitted resistance ratings to get this to work? I plan on just using 2 switches, listed is 240 and 390-- how close should i be to that?
scapeBeaufort, South Carolina · Dec 9, 2011#374
actually looking back at the wiring for two buttons, one single resistor of 630ohm seems like it would work-- between the two buttons on positive; still not sure about the set-cc pushbutton resistances range though
CTScottUSA, CT · Dec 9, 2011#375
Originally Posted by scape ↑
thx for the quick reply. what then would be the permitted resistance ratings to get this to work? I plan on just using 2 switches, listed is 240 and 390-- how close should i be to that?

You can use any value within these ranges:
216 to 264 ohms for one between resume and on/off
351 to 426 ohms for the one between set and resume
819 to 1001 ohms for the one between set and cancel

For the two button method, a single resistor 567 to 690 ohms can replace the 240 and 390 ohm resistors.

For current rating of the resistors, like the switches, it really doesn't matter, so 1/8 W, 1/4 W, 1/2 W, etc. are all fine.
scapeBeaufort, South Carolina · Dec 9, 2011#376
ah ok great, that helps big time in finding a proper resistor. why is it necessary to use the different clutch switch assembly, can the original clutch start-switch assembly be tapped in to?
CTScottUSA, CT · Dec 9, 2011#377
Originally Posted by scape ↑
ah ok great, that helps big time in finding a proper resistor. why is it necessary to use the different clutch switch assembly, can the original clutch start-switch assembly be tapped in to?
No, they are two different switch functions. The existing one detects that the pedal is fully pressed for starting and the CC one detects the initial press of the clutch pedal.
spectraLos Angeles · Dec 19, 2011#378
to do this do I need to buy a new terminal pin for the ecm? where can I get this?
CTScottUSA, CT · Dec 19, 2011#379
Originally Posted by spectra ↑
to do this do I need to buy a new terminal pin for the ecm? where can I get this?
I have the ECM pins available.
spectraLos Angeles · Dec 23, 2011#380
thanks so much! I got everything in and the test run went perfectly!
CTScottUSA, CT · Dec 23, 2011#381
Originally Posted by spectra ↑
thanks so much! I got everything in and the test run went perfectly!
Nice! And, in plenty of time for your road trip.
spectraLos Angeles · Dec 23, 2011#382
Yup! even had time to clean the car top to bottom

:-)
the beagleN Central, IA · Dec 31, 2011#383
After reading the entire thread on DIY cruise, I installed a $9.73 cruise on my son's 08 liftback, thanks to all of you for your perseverance and innovation. We ran the wires to the console between the seats. The two button controls are partially covered by the brake handle. A very clean install if I do say so myself.
CTScott, how can I get one of those ECM terminal pins?
CTScottUSA, CT · Jan 1, 2012#384
Originally Posted by the beagle ↑
After reading the entire thread on DIY cruise, I installed a $9.73 cruise on my son's 08 liftback, thanks to all of you for your perseverance and innovation. We ran the wires to the console between the seats. The two button controls are partially covered by the brake handle. A very clean install if I do say so myself.
CTScott, how can I get one of those ECM terminal pins?
PMed with payment info. I have the pins available.
badPennsylvania · Jan 7, 2012#385
I've used the CTScott cruise control system and procedure. works great. I have little experience working on cars. successful install.
badPennsylvania · Jan 7, 2012#386
oh but i should mention you'll need a variety of butt splices and extra wire ... i wish i could remember the gauges but its all around 16 to 22. depening on what wire you use to ground you might need a different gauge lug for that too.
menzEgypt · Jun 13, 2012#387
I am from Egypt (middle east). I have seen this DIY years ago but never had the guts to do it. I am a noob when it comes to car mechanics and also afraid of electronics :D. I don't know if my car has cruise function. To summarize, I need to check if PIN 40 has 12 volts when ignition on. Wish me luck everybody. I hope that the car has the function so I can do it, my 300 kms daily route to work would be so much better. I think that toyota must have installed it in all the cars not specific to a certain segment. When I first bought the car it had no rear speakers and when I bought the speakers and during installation, I found out that all the wiring is done and all I have to do it place the speakers and that was it. Do I need to remove the steering wheel to get to the D3 connector??? :d
CTScottUSA, CT · Jun 13, 2012#388
Originally Posted by menz ↑
I am from Egypt (middle east). I have seen this DIY years ago but never had the guts to do it. I am a noob when it comes to car mechanics and also afraid of electronics :D. I don't know if my car has cruise function. To summarize, I need to check if PIN 40 has 12 volts when ignition on. Wish me luck everybody. I hope that the car has the function so I can do it, my 300 kms daily route to work would be so much better. I think that toyota must have installed it in all the cars not specific to a certain segment. When I first bought the car it had no rear speakers and when I bought the speakers and during installation, I found out that all the wiring is done and all I have to do it place the speakers and that was it. Do I need to remove the steering wheel to get to the D3 connector??? :d
Unfortunately your Yaris does not support the OEM cruise control. For 06-11 Yaris, only US/Canada ones with the 1.5L engine have it built into the ECM.
menzEgypt · Jun 13, 2012#389
I really wished I have it. So just for my own curiouisity which one is the D3 connector where is it exactly
yaryarbingMaryland · Sep 1, 2012#391
Just installed the two switch DIY cruise control on my '07 Yaris Sedan. Can't believe it works! Not that I had any doubts in the DIY instructions. I have zero experience in electronics. I just bought the parts (<$10!), installed as instructed, and I now have cruise control!

Thanks so much for this thread and instructions. I am a traveling salesman with a four state territory. The cruise will make my travels SO much easier

-Yaryarbing
CTScottUSA, CT · Sep 2, 2012#392
Originally Posted by chanka ↑
Hi Scott,

If I don't have cruise control in my 08 yaris (M5) (New Zealand New) hatch how can I fit CC ?
Cheers.
Chanka

For your car you would need a complete aftermarket system, since your ECM does not have the functionality built in.
fascar228Islamabad · Mar 11, 2013#393
Hi All,

I have a 2007 Vitz JDM 1.0L can the Cruise control mod work for my vehicle....
mf4361SK · Mar 11, 2013#394
Since this thread is revived, I have to say, It worked on my 2007 Sedan (Canada)!! Started out with no tool, I spend ~$15 on it. Compare to, let say, OEM Cruise from dealership its almost nothing. Thanks CTScott for the awesome DIY writeup and everyone's help.

Now I need to work on making aesthetically look good.
johntamBraeside Ont · Mar 27, 2013#395
Thanks guys for the detailed instructions for the cruise control installation for my '07 \yaris. It works awesome. J&T
bonoxAustralia · Jun 21, 2013#396
Hi All

I tried this today on my December 2006 YR. Is there a way to tell if you've made a connection to pin40 on A21? Is there a test resistance to ground or another pin for example?

Mine also does not have the blue wire populated in the fuse box for the clutch switch either. Does this mean it's a no go? There is a pin at the bottom (just not a wire coming out of the plug), which I tried grounding, but couldn't get CC to work.

Thoughts any of you gurus? :) 🆘
CTScottUSA, CT · Jun 21, 2013#397
Originally Posted by bonox ↑
Hi All

I tried this today on my December 2006 YR. Is there a way to tell if you've made a connection to pin40 on A21? Is there a test resistance to ground or another pin for example?

Mine also does not have the blue wire populated in the fuse box for the clutch switch either. Does this mean it's a no go? There is a pin at the bottom (just not a wire coming out of the plug), which I tried grounding, but couldn't get CC to work.

Thoughts any of you gurus? :) 🆘
For the pin 40 test, measure the voltage on the wire with the ignition switch in the on position. You should see 12 V on that pin.

The missing blue clutch switch wire is potentially a bad sign. Did you verify that there was not a connector taped to the harness, just above the clutch pedal?
bonoxAustralia · Jun 21, 2013#398
Originally Posted by CTScott ↑
For the pin 40 test, measure the voltage on the wire with the ignition switch in the on position. You should see 12 V on that pin.

The missing blue clutch switch wire is potentially a bad sign. Did you verify that there was not a connector taped to the harness, just above the clutch pedal?
Thanks Scott

Will check pin potential - didn't look for connector at the time, but I don't have one.

Cheers

b
harda toenailSE Missouri · Dec 3, 2013#399
Is the clutch switch required? Is it's purpose to disengage the cruise when the clutch is pressed in?
CTScottUSA, CT · Dec 3, 2013#400
Originally Posted by harda toenail ↑
Is the clutch switch required? Is it's purpose to disengage the cruise when the clutch is pressed in?
The clutch switch is required for MT cars. The switch works the opposite of the clutch start switch, which is why it is a separate switch. It does disable CC when the clutch is touched, to prevent revving.