Replies continued
yarisbirdCypress, CA · Oct 3, 2010#301Very impressive nickhjort!
CTScott, do you still sell these indicator lights? If so, how can I purchase one from you? Also, where would I connect the wires if I'm installing an oem cruise control stalk on my 07 hatchback?
CTScottUSA, CT · Oct 3, 2010#302 Originally Posted by
yarisbird ↑ Very impressive nickhjort!
CTScott, do you still sell these indicator lights? If so, how can I purchase one from you? Also, where would I connect the wires if I'm installing an oem cruise control stalk on my 07 hatchback?
See this thread for links to the various methods of installing cruise:
DIY Cruise Control FAQ (2006-2010 Yaris) I do still sell the indicator modules. I don't have any ready to ship at the moment, but can build one up if you are interested.
yarisbirdCypress, CA · Oct 4, 2010#303 Originally Posted by
CTScott ↑ See this thread for links to the various methods of installing cruise:
DIY Cruise Control FAQ (2006-2010 Yaris) I do still sell the indicator modules. I don't have any ready to ship at the moment, but can build one up if you are interested.
Thanks CTScott. I would like to order one of these LED modules. Are they still $25? How do I send you payment?
CTScottUSA, CT · Oct 4, 2010#304 Originally Posted by
yarisbird ↑ Thanks CTScott. I would like to order one of these LED modules. Are they still $25? How do I send you payment?
I'll make one up this week and then PM you the paypal payment info. The price is still $25 shipped.
yarisbirdCypress, CA · Oct 22, 2010#305 Originally Posted by
CTScott ↑ I'll make one up this week and then PM you the paypal payment info. The price is still $25 shipped.
Hi CTScott,
Just wondering if you got a chance to make this switch yet.
CTScottUSA, CT · Oct 22, 2010#306 Originally Posted by
yarisbird ↑ Hi CTScott,
Just wondering if you got a chance to make this switch yet.
Yes. I'll PM you the paypal payment info.
yarisbirdCypress, CA · Oct 22, 2010#307Great. Thanks!
CTScottUSA, CT · Nov 8, 2010#308 Originally Posted by cicici00 ↑
Hello all,
I hope my question isn't stupid. I have been reading all the forum hours and hours. They are kind of confusing. BTW, I have 08 Yaris LB.
So, I ordered a cruise stalk from here:
http://cgi.ebay.com/ebaymotors/TOYOT...Q5fAccessories I understand that I can just "combine" the "DIY cruise control 07-08 with button" and "OEM stalk 2009", then everything should work magically.
Here are my questions:
1. So, the stalk I purchased from eBay could be just substituted as the switches in "DIY cruise control 07-08", right??
2. If Question 1 is a yes, then how do I know which wire from the stalk goes where?
3. Do I need to get any other parts besides the stalk?
1. Yes.
2. It actually doesn't matter which of the two goes to the ECM pin 40 and which goes to ground.
3. Yes. You need a repair pin for the ECM and one for the connector under the steering column. See this thread for the details:
DIY Cruise Control FAQ (2006-2010 Yaris) CB900F2Toronto · Nov 9, 2010#309Hi Scott.. I priced out the two repair kits for the connectors (82998-24250, 82998-12870), and man they are pricey.. They are $11.98 each. Do you know what comes in the kit for $11.98?
Originally Posted by
CTScott ↑ 1. Yes.
2. It actually doesn't matter which of the two goes to the ECM pin 40 and which goes to ground.
3. Yes. You need a repair pin for the ECM and one for the connector under the steering column. See this thread for the details:
DIY Cruise Control FAQ (2006-2010 Yaris)
CTScottUSA, CT · Nov 9, 2010#310 Originally Posted by
CB900F2 ↑ Hi Scott.. I priced out the two repair kits for the connectors (82998-24250, 82998-12870), and man they are pricey.. They are $11.98 each. Do you know what comes in the kit for $11.98?
A little piece of wire with the pin attached is all that you get for $12. I recently bought the parts so that I can offer the 3 pin/wire set for $10 shipped.
CTScottUSA, CT · Nov 9, 2010#311 Originally Posted by cicici00 ↑
Thanks for the answer. There must be something I still not getting. In the instruction, DIY Cruise Control 07-08, it did not say anthing about the "repair pin". If I missed it, please kindly point it out...
Isn't the repair pin.. just a piece of wire??
And, what is a repair pin? any pictures? what does it do?
Thanks!!
The DIY shows just sticking a piece of wire into the connector. This is not a good long term solution, as it will allow moisture to enter the sealed connector. The repair pin is one of the correct pins (with the rubber seal) that inserts into the connector.
EatomanMontreal · Nov 9, 2010#312CTScottUSA, CT · Nov 9, 2010#313 Originally Posted by
Eatoman ↑
It would, but I am sure it's a whole lot more expensive than simply adding the stalk and wires to use the ECM equipped CC.
EatomanMontreal · Nov 10, 2010#314 Originally Posted by
CTScott ↑ It would, but I am sure it's a whole lot more expensive than simply adding the stalk and wires to use the ECM equipped CC.
Expensive yes. But then again, there's always a price to pay for "stylish" features. 😁
gam668mich · Mar 17, 2011#315Hey CTScott I seen your set up on micro image 4 sale. I have a 2008 Yaris hatchback w/Automatic
vin# Starts J1DJ and ecm is 89661-52g51. Will your package work? If yes how do I pay You for the stalk and wires needed to do this? I would like to do this, IT WOULD BE A GREAT SAVINGS TO ME.... Thanks alot :
yariskids1Kansas · Apr 17, 2011#316Thanks to you and CTScott. Just did this yesterday and it works great. I used the 2 switch set up. Took about 2.5 hours all in, time very well spent. Thanks again!
PROX4x4CO · Jun 17, 2011#317Thanks for the step by step info, I was wondering if it works for a 08 Yaris HB? and what type of switches are they, are they the click type (sorry not very professional) or push on-push off type?
Thank you,
CTScottUSA, CT · Jun 17, 2011#318 Originally Posted by
PROX4x4 ↑ Thanks for the step by step info, I was wondering if it works for a 08 Yaris HB? and what type of switches are they, are they the click type (sorry not very professional) or push on-push off type?
Thank you,
The switches need the be momentary normally open switches. Momentary is the type like a key on a keyboard, where you press it and it pops back up. Normally open means that it completes the circuit when you press it.
white_riceOntario, Canada · Jun 19, 2011#319Is anyone having an issue with the cruise control indicator light? For some reason my LED doesn't light up when I engage the cruise (OEM stalk) all the time. I will press it again to disengage it and then it comes on. It will do that sometimes, and sometimes it won't come on at all when I engage it, and other times it works properly. At first thought, was thinking it might be a short -- but it only happens when the cruise is either engaged or disengaged as opposed to just randomly coming on or off while driving.
CTScottUSA, CT · Jun 19, 2011#320 Originally Posted by
white_rice ↑ Is anyone having an issue with the cruise control indicator light? For some reason my LED doesn't light up when I engage the cruise (OEM stalk) all the time. I will press it again to disengage it and then it comes on. It will do that sometimes, and sometimes it won't come on at all when I engage it, and other times it works properly. At first thought, was thinking it might be a short -- but it only happens when the cruise is either engaged or disengaged as opposed to just randomly coming on or off while driving.
The indicator module detects the voltage change when the on/off switch is pressed. If the connections between the ECM and the stalk are not solid, then the voltage drop across them can cause the module to misinterpret the press.
PROX4x4CO · Jun 29, 2011#321 Originally Posted by
CTScott ↑ It's actually 240 and 390.
You can use any value within these ranges:
216 to 264 ohms for one between resume and on/off
351 to 426 ohms for the one between set and resume
819 to 1001 ohms for the one between set and cancel
For wattage, 1/8 or 1/4 watt is fine.
I wonder if this switch would work for the on/off & Set setting for this type of cruise control setup?
http://cgi.ebay.com/ebaymotors/CARLI...Q5fAccessories CTScottUSA, CT · Jun 29, 2011#322 Originally Posted by
PROX4x4 ↑
The switches need to be momentary. That on is ON/OFF/Momentary, so it would be OK in one direction, but not the other. You'd want Momentary/Off/Momentary.
PROX4x4CO · Jun 29, 2011#323 Originally Posted by
CTScott ↑ The switches need to be momentary. That on is ON/OFF/Momentary, so it would be OK in one direction, but not the other. You'd want Momentary/Off/Momentary.
Been looking around to see if I can make something funky using your lighting module and resistors set up with below switches, but I guess nothing beats the stock CC setup.
http://cgi.ebay.com/1-Stainless-Mome...item43a7fb8cea Your innovations clears the way to personal styling of Yarises in this world :D
Thanks again! 🤘
CTScottUSA, CT · Jun 29, 2011#324 Originally Posted by
PROX4x4 ↑ Been looking around to see if I can make something funky using your lighting module and resistors set up with below switches, but I guess nothing beats the stock CC setup.
http://cgi.ebay.com/1-Stainless-Mome...item43a7fb8cea Your innovations clears the way to personal styling of Yarises in this world :D
Thanks again! 🤘
Those would work, and the lighting is isolated from the switching, so that's good as well. For $9 each though the cost for 4 is the same as what I sell the stalks for.
david.gartee1Columbia, TN · Jul 2, 2011#325Hey all, I just wanted to thank everyone on this forum. I just did my install of the 4-Button CC. It works perfectly after a little troubleshooting. The only problem is that I just have the wire chillin' in the ECU. I have no idea how long it will stay there, but it stayed in on my 60 mile round trip to/from work. I do not wish to buy the real wire from Toyota, but I will if I must. But I was wondering something: I have a spare wiring harness adapter laying around with the pins kinda like the ones that go in the ECU (I assume), and I was wondering if I can seat those in the ECU for a permanent solution.
CTScottUSA, CT · Jul 2, 2011#326 Originally Posted by
david.gartee1 ↑ Hey all, I just wanted to thank everyone on this forum. I just did my install of the 4-Button CC. It works perfectly after a little troubleshooting. The only problem is that I just have the wire chillin' in the ECU. I have no idea how long it will stay there, but it stayed in on my 60 mile round trip to/from work. I do not wish to buy the real wire from Toyota, but I will if I must. But I was wondering something: I have a spare wiring harness adapter laying around with the pins kinda like the ones that go in the ECU (I assume), and I was wondering if I can seat those in the ECU for a permanent solution.
They need to be the exact same pins, otherwise the pin latch mechanism will not snap back into place. I sell the ECM pins (with about 2' of wire) for $5 shipped, which is a lot less than the dealer charges.
i-transMontréal, Québec · Jul 8, 2011#327Hi,
i have try to install this cruise control mod...
But no cruise function...
All switch are okay, i have buy the cc switch, i have connected the switch to the white and the blue wire ( around the purple wire ).
my switch set-up are the same of the tutorial (4 switch with 240, 390 and 910 resistor )
I have buy 2 D3 wire and a A21 connector.
the a21 connector goes to my red wire on my sitch and to the pin1 of the d3 connector.
my black wire goes to pin2 of d3 connector and to the negative.
I start the car, i push on the "on" switch...
at 100Km/h i push on the "set" and nothing happen...
what's wrong?!?🤷
CTScottUSA, CT · Jul 8, 2011#328 Originally Posted by
i-trans ↑ Hi,
i have try to install this cruise control mod...
But no cruise function...
All switch are okay, i have buy the cc switch, i have connected the switch to the white and the blue wire ( around the purple wire ).
my switch set-up are the same of the tutorial (4 switch with 240, 390 and 910 resistor )
I have buy 2 D3 wire and a A21 connector.
the a21 connector goes to my red wire on my sitch and to the pin1 of the d3 connector.
my black wire goes to pin2 of d3 connector and to the negative.
I start the car, i push on the "on" switch...
at 100Km/h i push on the "set" and nothing happen...
what's wrong?!?🤷
Do you have an AT or MT?
There is no purple wire near the CCS wire in pin 40 of connector A21. Looking at the connector from the wire entry side, there is a blue wire with silver marks next to it on the left and a brown wire next to it in the next row.
Why did you add pins to D3? You only need to do so if using the OEM stalk, not for using the DIY switch method.
i-transMontréal, Québec · Jul 8, 2011#329i have a MT.
this is the reason why i have connect my cc clutch switch on the white and the blue wires (the purple are in the meedle (in the fuse panel under the hood in the conductor side).
why i have connect 2x D3 connector, confusion between 2 diy.....
i go to disconnect the 2x D3 connector, and go to test!
the voltage was okay on my 4 cc switch (12v. when ignition are on).
the 2x D3 connector was my error, it was possible to theses connector cause the malfunction?
**sorry i'm very bad in english**
CTScottUSA, CT · Jul 8, 2011#330 Originally Posted by
i-trans ↑ i have a MT.
this is the reason why i have connect my cc clutch switch on the white and the blue wires (the purple are in the meedle (in the fuse panel under the hood in the conductor side).
why i have connect 2x D3 connector, confusion between 2 diy.....
i go to disconnect the 2x D3 connector, and go to test!
the voltage was okay on my 4 cc switch (12v. when ignition are on).
the 2x D3 connector was my error, it was possible to theses connector cause the malfunction?
**sorry i'm very bad in english**
OK. That makes more sense.
Being connected to D3 shouldn't cause issues, except that if you are relying on that for the ground of the second wire, it will just be floating, since the other end of the connector is not connected. On you switch array, one side goes to A21-40 and the other to ground.
i-transMontréal, Québec · Jul 8, 2011#331i have disconnected the 2 D3 wire.
I have make a road test and it was unsuccessful 😢
it's the second day i try to make it come true.
this morning i have buy 4 new switch, re-install, re-soldering etc...
i have try with my ccclutch switch and with a jumper...
i have 12v when i put my ignition on, and 0 when it off.
and my "on" button was 1 red wire go to A21 pin 40, and the other to the kick panel (ground).
when i press "set" "resume" or "cancel" the voltage is flickering between 12 and 0v for 1 sec. approx.
i don't know what is the problem at this time...
CTScottUSA, CT · Jul 8, 2011#332 Originally Posted by
i-trans ↑ i have disconnected the 2 D3 wire.
I have make a road test and it was unsuccessful 😢
it's the second day i try to make it come true.
this morning i have buy 4 new switch, re-install, re-soldering etc...
i have try with my ccclutch switch and with a jumper...
i have 12v when i put my ignition on, and 0 when it off.
and my "on" button was 1 red wire go to A21 pin 40, and the other to the kick panel (ground).
when i press "set" "resume" or "cancel" the voltage is flickering between 12 and 0v for 1 sec. approx.
i don't know what is the problem at this time...
Can you post a pic of your switch/resistor wiring?
i-transMontréal, Québec · Jul 8, 2011#333give me 2 minutes and i will post!
i-transMontréal, Québec · Jul 8, 2011#334This is my 4 switch.
momentary n.o
CTScottUSA, CT · Jul 8, 2011#335That looks fine. And, the negative wire goes to a good chassis ground?
i-transMontréal, Québec · Jul 8, 2011#336the ground goes to the kick panel on the driver side
CTScottUSA, CT · Jul 8, 2011#337OK. So if you measure between the positive and negative wires, you see 12V with the ignition on, and if you hold the ON/OFF button, it stays at 0V?
Also, the clutch switch is adjusted so that it is fully pressed when the clutch is up?
i-transMontréal, Québec · Jul 8, 2011#338yes, 0v when i press the On/Off button.
the clutch switch was ajusted and fully pressed.
CTScottUSA, CT · Jul 8, 2011#339OK. And just to verify:
The top switch is on/off 0 You press that once.
The switch on the right (which becomes the left when installed) is the set button. You get to 25MPH or higher and press that one (having already pressed the top one above).
i-transMontréal, Québec · Jul 8, 2011#340exactly!
when i start my car i press the "on" button, when i go faster than 45Km/h i try to press "set" button.
i have try to just press, and keep my finger pressing this button about 3-5sec.
no result!
the clutch control switch has polarity?
the red wire on my ccswitch goes to the blue or the white wire in the fuse box in the driver side of the hood?
or nothing important?
CTScottUSA, CT · Jul 9, 2011#341 Originally Posted by
i-trans ↑ exactly!
when i start my car i press the "on" button, when i go faster than 45Km/h i try to press "set" button.
i have try to just press, and keep my finger pressing this button about 3-5sec.
no result!
the clutch control switch has polarity?
the red wire on my ccswitch goes to the blue or the white wire in the fuse box in the driver side of the hood?
or nothing important?
The clutch switch is not polarized. The only other thing I can think of is that the switches are poor quality and that rather than making a clean connection when pressed that they "bounce" causing multiple ons and offs with a single press.
i-transMontréal, Québec · Jul 10, 2011#342the switchs seem to be okay, no pulse when i push button.
i fugure that the problem are my cc clutch switch...
if my cc clutch switch are not okay, the cc are not functionnal.
i have try with the jumper in the fusebox, and unfortunately i have the same result...
i really don't know what is my cc problem, but i want to resolve that soon!
CTScottUSA, CT · Jul 10, 2011#343 Originally Posted by
i-trans ↑ the switchs seem to be okay, no pulse when i push button.
i fugure that the problem are my cc clutch switch...
if my cc clutch switch are not okay, the cc are not functionnal.
i have try with the jumper in the fusebox, and unfortunately i have the same result...
i really don't know what is my cc problem, but i want to resolve that soon!
The only way to tell if the switches are bouncing is with an oscilloscope. A voltmeter is too slow.
Also, are you absolutely sure that you are on the correct pin on the ECM?
i-transMontréal, Québec · Jul 10, 2011#344yes!
my connector was on the pin 40, i have make a re-check, and it was on the good pin.
For the switch, i have tested at this time with 14 switchs, buy at different store.
i have tested the 4 switchs mode, and the 2 switchs mode.
Actually i have 2 switch untested, i try these 2 switch after the lunch.
If the test are not okay, i pass an order for the stalk, or i pass an order for to momentary switch on an internet store....
i-transMontréal, Québec · Jul 10, 2011#345i have try my last switchs, and nothing new...no cruise control!
on my first switch i have 12,35volts.
when i push on, i have 0volts.
on the second switch i have 8,35volts.
when i push on this second switch i have 0volts.
i have 2 resistors ( 1x240 and 1x390 in serie ).
what are the best way to test my cruise control clutch switch?
i suppose that is my problem. (i have try with the jumper but, no result)
i have take a read of this 2 wires (in the fusebox, and i have no read (0volts)
when i push the clutch, i have no read ...)
if i read the white wire behind the puple wire, with the other blue wire, in diagonal i have a read of 12,33 volts.
I suppose that my blue wire behind the purple wire, are no voltage on in.
CTScottUSA, CT · Jul 10, 2011#346That looks fine for a test setup. Snap a pic of your clutch switch wiring at the fuse box.
i-transMontréal, Québec · Jul 10, 2011#347this is my clutch switch wiring in the fusebox
CTScottUSA, CT · Jul 10, 2011#348You're in the right place. The blue wire needs to have +12V to it in order for cruise to be enabled.
i-transMontréal, Québec · Jul 10, 2011#349the blue wire have +12v when i release the clutch in link with the white wire?
because i don't have any power on my clutch switch.
my wire are clutch switch +/- to fusebox (white and blue wires )
CTScottUSA, CT · Jul 10, 2011#350 Originally Posted by
i-trans ↑ the blue wire have +12v when i release the clutch in link with the white wire?
because i don't have any power on my clutch switch.
my wire are clutch switch +/- to fusebox (white and blue wires )
Correct - When the clutch is not pressed the blue gets 12V from the white and when it is pressed it opens and the blue has 0V.