sweetness
"Parmas" Motor
490 posts · 124,989 views · page 5 of 10
Replies continued
read my above post. There is no noticable lag.Originally Posted by advocate ↑So if front mount creates huge turbo lag and top mount spools faster but hotter (and thus less boost), how the hell do you pick which one you want? Sounds like very big drawbacks on both parts.
I would think a larger engine, which creates more overall exhaust, wouldn't suffer as much from excess lag from a front mount versus a Yaris which burns much less overall fuel. Correct?
You are over simplifying it a fair bit. Both setups can be made to work as good as each other and it depends on what purpose you want to design it for. There's alot of variables to be taken into account though to get it right (eg. piping diameter, bends, pressure drops, turbo sizing and efficiency ranges, gear ratios, cam design/ duration/ timing, engine timing, bov design etc etc).Originally Posted by advocate ↑So if front mount creates huge turbo lag and top mount spools faster but hotter (and thus less boost), how the hell do you pick which one you want? Sounds like very big drawbacks on both parts.
I would think a larger engine, which creates more overall exhaust, wouldn't suffer as much from excess lag from a front mount versus a Yaris which burns much less overall fuel. Correct?
And if all else fails, turn the antilag on
ha, true! just do it my way, that's the best. (just kidding!)
Some recent pics...
Damn the camera got low battery when I was taking a video. Better luck next time....
Damn the camera got low battery when I was taking a video. Better luck next time....
3 attachments not included in this copy
Post Videos!!!!!
It looks mean. Does it sound mean?👍
awesome hood, very aggressive.
I would like to see (when you have time) a closer pic of the BOV flange, it looks interesting.
Also interior - any gauge set up?
I would like to see (when you have time) a closer pic of the BOV flange, it looks interesting.
Also interior - any gauge set up?
Look like a standard HKS bov flange to me , ie the bov sits in the circle flange and is held in with a C-clip .Originally Posted by cali yaris ↑awesome hood, very aggressive.
I would like to see (when you have time) a closer pic of the BOV flange, it looks interesting.
Also interior - any gauge set up?
Amazing project man 👍 I've been following your build and am stoked to see you finally got it all together in the car and running I can't wait to see the dyno #'s
wow parmas, your car looks great!! its a job nicely done! the intercooler is so sexy!
Thanks guys I appreciate your comments and these are what keep me updating!
The BOV flange is the standard HKS weld on flange as described blacksandiegovitz in his post.
RE: Yaris-me post... well it sounds awesome as described by many here although I need a good camera for you to enjoy the sound 😛
I don't think of dyno it for now but will not miss a video on street.... Please let me enjoy it a while !!!
BTW here is a shot from inside incl. my lovely girl
The BOV flange is the standard HKS weld on flange as described blacksandiegovitz in his post.
RE: Yaris-me post... well it sounds awesome as described by many here although I need a good camera for you to enjoy the sound 😛
I don't think of dyno it for now but will not miss a video on street.... Please let me enjoy it a while !!!
BTW here is a shot from inside incl. my lovely girl
1 attachment not included in this copy
Today I went up to a drag race to check how all is working out. Well it was noticed that injectors are maxing out at (about 98% inj duty cycle) 9psi 6000rpm with an average afr of 11:1.
Well although the car runs fine I am sure I will not get a good time with this low boost (thinking of 14s blehh). What do you recommend about the injectors, Brand? ***cc? Type?
I think garm can help me on this :)
Also engine gives startup problems when cold or when not using it for a half an hour or so? Sometimes needs 3 starts to ignite, is this normal or the plugs are too on the cold side?
Thanks!
Well although the car runs fine I am sure I will not get a good time with this low boost (thinking of 14s blehh). What do you recommend about the injectors, Brand? ***cc? Type?
I think garm can help me on this :)
Also engine gives startup problems when cold or when not using it for a half an hour or so? Sometimes needs 3 starts to ignite, is this normal or the plugs are too on the cold side?
Thanks!
what plugs, and what gap? The gap can make a difference.
11:1 is on the rich side, you'll get a better result around 11:7
sorry, what management again?
Is your car using the ECU's stock cold-start program?
11:1 is on the rich side, you'll get a better result around 11:7
sorry, what management again?
Is your car using the ECU's stock cold-start program?
nice. I am curious about final results.
These injectors should work well... http://www.ptuning.com/html/search-r...nd=dw&cmbYear=
they will drop right in and use factory plugs.
Do you have the stock fuel pump?
These injectors should work well... http://www.ptuning.com/html/search-r...nd=dw&cmbYear=
they will drop right in and use factory plugs.
Do you have the stock fuel pump?
Plugs are Denso Iridium power IK series. Gap is 0.4mm with 5Kohm resistor. Part no is IK22#4Originally Posted by cali yaris ↑what plugs, and what gap? The gap can make a difference.
11:1 is on the rich side, you'll get a better result around 11:7
sorry, what management again?
Is your car using the ECU's stock cold-start program?
Management is Gotech PROX full standalone, stock ecu not used. Ecu has a map for startup fuelling appropriately adjusted by tuner. I just want to assure that problem is not coming from plugs heat range.
RE: Blown_xa injectors link... why you say "should work fine" are they tested before on a 1NZ?
RE: Air to fuel ... can anyone tell me the appropriate range the afr should be at :
- Idle 1200rpm
- 2Krpm until boost
- above 3500rpm after boost?
Also, since I am considering replacing the injectors to above 600cc, does the engine will startup up rich or lean with a fuel map tune on 340cc inj?
See attachment from a log run at first gear @ 6Krpm ..injector duty are 98%
1 attachment not included in this copy
.4mm is .0157 inches. Mine were gapped at .028 and we brought that down to .024 when tuning on the dyno. I think your gap is very tight!
A/F on my car:
Idle: 14.1-14.7
Cruising: 13.0 - 13.5 is the range I've seen, more or less
under boost: 12.5 down to 11.7 at full boost, depends on load etc.
hope that helps.
A/F on my car:
Idle: 14.1-14.7
Cruising: 13.0 - 13.5 is the range I've seen, more or less
under boost: 12.5 down to 11.7 at full boost, depends on load etc.
hope that helps.
Also, since I am considering replacing the injectors to above 600cc, does the engine will startup up rich or lean with a fuel map tune on 340cc inj?you'll be under 5% duty cycle at idle, so could be a little rich, might need more tuning all around. Overall though, your management should maintain correct A/F.
yes when I mean "should work fine", i mean as long as your fuel management can handle the increased size. The injectors themselves will drop right in. Same denso casing as factory. Depending on your projected whp choose between the 550's and 750's. Im thinking 550's would be plenty considering you have a return set-up. 🙂
What Brand are the plugs? Thus this gap difference might be related to octane difference? I am running 90 octane so sure your fuel ignites better so thats what might the gap serve for!Originally Posted by cali yaris ↑.4mm is .0157 inches. Mine were gapped at .028 and we brought that down to .024 when tuning on the dyno. I think your gap is very tight!
A/F on my car:
Idle: 14.1-14.7
Cruising: 13.0 - 13.5 is the range I've seen, more or less
under boost: 12.5 down to 11.7 at full boost, depends on load etc.
hope that helps.
Thanks for that afr reading garm, I never seen 12s on either level! BTW you are sure that these readings are good for lower octane level fuel?
What do you think about the TC injectors Garm? Do you recommend these for my setup? Is there anyone using them on his motor?
the tC injectors (factory) would be ok for low boost. I was not able to get past 149whp with them as they maxed out. Seeing as you have a return set up im thinking they can put out more juice.
As far as AFR ratio and octane rating, timing is what is most important to optimize power and to prevent knock/detonation. The only way to optimize timing is on the dyno though. AFR should be targeted the same regardless of octane rating.
We tuned 2 customers tC's for 400whp, one with 91 octane (what was readily availible to that customer) and one with 93 octane. AFR were the same, timing is what has to be adjusted(less timing for 91)
As far as AFR ratio and octane rating, timing is what is most important to optimize power and to prevent knock/detonation. The only way to optimize timing is on the dyno though. AFR should be targeted the same regardless of octane rating.
We tuned 2 customers tC's for 400whp, one with 91 octane (what was readily availible to that customer) and one with 93 octane. AFR were the same, timing is what has to be adjusted(less timing for 91)
I don't know how much do you mean by low boost but since I built the engine it's none sense to stay low boosted!
I am projecting 16psi on a Garret T28 though!
I am projecting 16psi on a Garret T28 though!
oh yea factory tC injectors would be way too small. 550's would be goodOriginally Posted by Parmas ↑I don't know how much do you mean by low boost but since I built the engine it's none sense to stay low boosted!
I am projecting 16psi on a Garret T28 though!
Hi Parmas,
Just want to share with you that I purchased a set of 445cc customized injectors from FIC for my rebuilt next month, but I can't tell you whether they'll work great until its in.
Am already thinking they might be too small as I'm not converting to a return setup? :(
Picture not included in this copy
Just want to share with you that I purchased a set of 445cc customized injectors from FIC for my rebuilt next month, but I can't tell you whether they'll work great until its in.
Am already thinking they might be too small as I'm not converting to a return setup? :(
Picture not included in this copy
this may sound out there but there was an article in turbo mag a year or 2 back and it had an equation that you could use. dont quote me exactly but if i remember right you could plug in displacement,horsepower goal, and a few other factors and it would get you a good estimate of what cc injector you needed.
Mine are 340cc with a return setup running rich at all times @ 10psi. So the 445cc should work fine till 250BHP.Originally Posted by changchewsoon ↑Hi Parmas,
Just want to share with you that I purchased a set of 445cc customized injectors from FIC for my rebuilt next month, but I can't tell you whether they'll work great until its in.
Am already thinking they might be too small as I'm not converting to a return setup? :(
Picture not included in this copy
Finally we decided what injectors will suit best and we chose the Siemens Deka 4 630cc.
These injectors flow 220 lbs/hr at 43.5 PSI ( 3 BAR ) and more at higher PSI! These units are low-impedance and require peak and hold injector drivers or additional resistors for saturation drivers. Despite the high flow rate, they are linear and controllable at low pulse widths compared to other extreme flow injectors! These injectors are sometimes referred to as 212lb/hr or 225lb/hr injectors
Any has experience on these?
These injectors flow 220 lbs/hr at 43.5 PSI ( 3 BAR ) and more at higher PSI! These units are low-impedance and require peak and hold injector drivers or additional resistors for saturation drivers. Despite the high flow rate, they are linear and controllable at low pulse widths compared to other extreme flow injectors! These injectors are sometimes referred to as 212lb/hr or 225lb/hr injectors
Any has experience on these?
1 attachment not included in this copy
If I remember correctly, these injectors were pretty popular with WRX guys.Originally Posted by Parmas ↑Finally we decided what injectors will suit best and we chose the Siemens Deka 4 630cc.
These injectors flow 220 lbs/hr at 43.5 PSI ( 3 BAR ) and more at higher PSI! These units are low-impedance and require peak and hold injector drivers or additional resistors for saturation drivers. Despite the high flow rate, they are linear and controllable at low pulse widths compared to other extreme flow injectors! These injectors are sometimes referred to as 212lb/hr or 225lb/hr injectors
Any has experience on these?
Well that's good news since that increase the probability of being ones of the very best racing injectors one could own.
I hope they are efficient as advertised as these will probably be a good indeed upgrade. Bye Bye tuning probs :)
I hope they are efficient as advertised as these will probably be a good indeed upgrade. Bye Bye tuning probs :)
Some pictures of the rear mounting. Sorry about the blured image but the camera sucks at close ups!
4 attachments not included in this copy
UPDATES:
UPGRADED INTERCOOLER HOSES TO SAMCO RED :)
SHOWING CUSTOM BLUE WATER HOSES ASWELL
TRD CAP
UPGRADED INTERCOOLER HOSES TO SAMCO RED :)
SHOWING CUSTOM BLUE WATER HOSES ASWELL
TRD CAP
2 attachments not included in this copy
cool, very colorful -- what throttle body is that?
Stock 1NZ oneOriginally Posted by cali yaris ↑cool, very colorful -- what throttle body is that?
What do you think about the rear mounting I posted before garm?
Sexy engine! You need a pink dip stick to set it off!🙂
OR >>> Garm's Intake Mainfold 😁Originally Posted by yaris-me ↑Sexy engine! You need a pink dip stick to set it off!🙂
I'm waiting . . .
BTW just found this on my pc 😁 > http://www.youtube.com/watch?v=u0wage2LBdM
This week we installed Siemens Deka 4 630cc injectors. Since the Siemens housing length is slightly different from original toyota injectors they needed to be "modified" to match the fuel rail.
Now needs tuning from scratch, I hope it makes real power with these on 🙇
Now needs tuning from scratch, I hope it makes real power with these on 🙇
ooh man can't wait for new results!! I have great hopes for this project!
My tuner just called in to tell that tomorrow will trial the car for some drag races. I am expecting 16psi or more boost with better AFR numbers than the previous tune.Originally Posted by cali yaris ↑ooh man can't wait for new results!! I have great hopes for this project!
Guess what? ..... if all goes well I think I will be the one to trial the Gude Performance Head package on our 1NZ. I already send him an e-mail to get some more details on cams....
Stay tuned!
You're drag racing tomorrow? or tuning tomorrow, or both... ? 🤷
Both :) Since we tune specifically on drag road for a precise and realtime tuning...Originally Posted by cali yaris ↑You're drag racing tomorrow? or tuning tomorrow, or both... ? 🤷
oh "street tuning", gotcha.
Some bad news.... 🙁
Yesterday we done a compression test since we are still having trouble idle and slow runing the engine. Well it result that 2 cyclinders are loosing compression and probably some valves not sealing properly...
There is also a problem to convert the engine with the authorities (due to some changes in law) since there is a fine difference due to bigger displacement (probably within $2000 range😳 ) So we are now intending to modify the 2NZFE 1.3L engine block to match the 1NZFE rods and in the meantime solving aswell the problem of the compression. We have to measure all the necessary points of the block in order to make this happen....
This will cost lots of money & time and since I am out of cash it will be a while to update my status....
Yesterday we done a compression test since we are still having trouble idle and slow runing the engine. Well it result that 2 cyclinders are loosing compression and probably some valves not sealing properly...
There is also a problem to convert the engine with the authorities (due to some changes in law) since there is a fine difference due to bigger displacement (probably within $2000 range😳 ) So we are now intending to modify the 2NZFE 1.3L engine block to match the 1NZFE rods and in the meantime solving aswell the problem of the compression. We have to measure all the necessary points of the block in order to make this happen....
This will cost lots of money & time and since I am out of cash it will be a while to update my status....
aw, so sorry to hear this. Do you think the motor came to you with these problems?
Is this your first compression test on it???
Is this your first compression test on it???
It was checked the compression after we opened it to check all things right and found loosing. The problem should have been solved by then but it seems that it isn't infact.Originally Posted by cali yaris ↑aw, so sorry to hear this. Do you think the motor came to you with these problems?
Is this your first compression test on it???
I am thinking of making a 2NZFE block conversion to match the 1NZFE rods. Since the 2 blocks have the same bore size of 75mm, what issues (if there are) I could face doing this? Is there something I need to know before I get into it or else is it possible to make it without much complications?
Garm... and can assure you and Parma, that the motor had excellect compression when we sold it.Originally Posted by cali yaris ↑aw, so sorry to hear this. Do you think the motor came to you with these problems?
I am not saying that the engine was defective when sold.Originally Posted by turboecho2005 ↑Garm... and can assure you and Parma, that the motor had excellect compression when we sold it.
When the engine arrived, it was opened and checked that all parts match the details. After assembling a compression test was made and marked loosing. The mech said they solved it and I continued to finally tune in. When we noticed having several idle and slow running problems we checked again to be sure and found loosing again.
I think there is a funny thing around and someone fu**ed me from behind on this
Vacuum was -20 if I remember correctly.Originally Posted by cdydjded ↑A proper test that would have determined the condition of this engine is not a compression test, its a leak down test. A compression test only tells you the compression psi in the cylinder chamber but it does not telling you if the piston rings or valves are sealing correctly. BTW how much vacuum was you boost guage reading at idle?
Tell me more about this leak down test
Nice test I didn't know about it since now. Interesting tool ... what brand do you recommend?Originally Posted by cdydjded ↑Here is a good article:
http://www.carcraft.com/techarticles...ter/index.html
My car is @ -22 so -20 is not that different. You low compression issue could be one of the following problems:
Piston ring end gap wrong
Piston to cylinder wall clearance wrong
Valve to valve seat problem
Crack or broken ring lands
These are just a few that I can list. Im not saying it has to be one of these, but its a possibility.
If you have a compression tester, you can easily tell if it's the rings or the valves which are causing the problem. Run the compression test as you would normally and take note of the reading.
Then remove the compression tester fitting and drop a teaspoon of oil (any normal mineral oil will do, castor oil, motor oil, doesn't really matter as long as it is thin (ie. not gearbox oil)) down the spark plug hole and then repeat the compression test. The oil you put down the combustion chamber helps the rings to seal better. If the reading is the same as before the oil was added, then the problem is in the head (valves, valve guides etc). If the reading is dramatically better than without the oil, then you look towards your pistons and rings for the problem.
If the reading is only slightly better than before you added the oil, but still low compared to the other pistons, then you possibly have a bent rod.
Then remove the compression tester fitting and drop a teaspoon of oil (any normal mineral oil will do, castor oil, motor oil, doesn't really matter as long as it is thin (ie. not gearbox oil)) down the spark plug hole and then repeat the compression test. The oil you put down the combustion chamber helps the rings to seal better. If the reading is the same as before the oil was added, then the problem is in the head (valves, valve guides etc). If the reading is dramatically better than without the oil, then you look towards your pistons and rings for the problem.
If the reading is only slightly better than before you added the oil, but still low compared to the other pistons, then you possibly have a bent rod.
A proper test that would have determined the condition of this engine is not a compression test, its a leak down test.Read Rob's post, a compression test can tell you a lot, and IS one "proper" test for the condition of an engine. A leak-down test is also a proper test.
Garm... and can assure you and Parma, that the motor had excellect compression when we sold it.What was the compression in each cylinder, and was this information given to Parmas? (in which case, Parmas you can post the information).