Yarisworld Archive

"Parmas" Motor

490 posts · 124,989 views · page 3 of 10

Replies continued

changchewsoonMalaysia · May 22, 2009#101
hi parmas, i do agree with you that having a bov is important for turbo cars as without it when your throttle plate closes and the air would have no where to go but to hit back the turbine and causing surge.

what i was trying to suggest is that if your car setup still retains the MAF sensor it will be good to perform a recirculation from the BOV back in to the intake. Post MAF but pre turbo.

recirculating will not cause the air to be forced back in to the engine because your throttle plate is already closed. it will recirculate through the bov to the intake, back to the bov again to the intake and the cycle continues. hence its called "recirculation".

i know what you mean by removing the bov and having air to remain "ready" in the intake, well you can't remove the bov totally because if you do that you're gonna hurt your turbo in the long run.

however, with a recirculation setup most ppl will notice an increase in throttle response due to the fact that the air is "there" the moment your throttle plate opens. remember, its post MAF and pre turbo, so its just air circulating within your intake, you could call it close loop if you want, which many factory fitted turbo cars such as audi and VW is practicing. if you look at a stock turbo subaru or evo, you would notice they are running close loop intake as well.

my argument is that your MAF has already registered a certain amount of air passing through it and sends signal to the ECU to send fuel to match it, when you vent it out to atmosphere the ECU has no idea and hence you run rich.

the recirculation is not meant to improve power, it is meant to prevent MAF equipped cars to go rich every time you shift gears and messing up with your fuel trims. some cars will even stall between gear shifts if they do not perform recirculation.

im not saying it is a must for you to recirculate, im just suggesting that for MAF equipped cars recirculating is a better option rather than venting to atmosphere so you don't run rich, mess up your fuel trims and face chances of stalling thats all.
cali yarisCanoga Park, CA · May 22, 2009#102
^ Very good explanation. On my car with standalone we have no MAF so no need for recirculated configuration.
Nexus1155Dorchester · May 22, 2009#103
I thought clamping the MAF voltage makes it so that you don't have to worry about the MAF readings and that its just read from the emanage, so if it is clamped can you still use a BOV? I mean i know recirc valves are the way to go in all aspects, but you know, some rice is a little nice.
changchewsoonMalaysia · May 22, 2009#104
the reason why we clamp the MAF is beause the moment you build boost past a certain stage the MAF gets saturated if it sends a voltage anything higher that 5v to the ECU then the ECU will throw a CEL. so the MAF clamp is good for WOT.

but when you're in closed loop, clamping the MAF has no effect as your ECU is relying on your stock O2 narrowband for feedback to maintain AFR at 14.7.

you could trying clamping your MAF at a fixed voltage across the entire RPM range, but im pretty sure you'll see your fuel trims will have a high readings of negative fuel trimmings in closed loop and if it maxes out or it can't pull fuel fast enough you'll get a too rich CEL.

you only start clamping when the MAF is nearing its limit, that usually happens around WOT unless you're boosting very high and the MAF itself is already maxed out during low/partial throttle.

some of the boosted yaris here uses the f-manage to control the afr in closed loop, im using the innovate lc-1 as it has a narrowband o2 output and its programmable.

we had a Toyota Wish here who uses a GT28 turbine and his stock MAF wasn't able to handle it even on low/partial throttle at low RPMS and his ECU kept throwing a too rich CEL even when the MAF is clamped. that is because during closed loop, his ECU wasn't able to pull fuel fast enough to maintain the 14.7 afr and he keeps going rich and when the ECU sees that it can't get the afr back to normal after a period of time it throws a CEL.
rob323Joyner, Brisbane · May 22, 2009#105
Originally Posted by changchewsoon ↑
my argument is that your MAF has already registered a certain amount of air passing through it and sends signal to the ECU to send fuel to match it, when you vent it out to atmosphere the ECU has no idea and hence you run rich.

the recirculation is not meant to improve power, it is meant to prevent MAF equipped cars to go rich every time you shift gears and messing up with your fuel trims. some cars will even stall between gear shifts if they do not perform recirculation.
Some have speculated that it is unwise to run an atmo bov with a MAF as that extra richness during gear changes can wash or dilute the oil on the bores and cause premature ring wear and other associated long term problems.
+1 for recirculation, even better if the return piping from the bov can be somehow aimed at the turbo inlet inthe right way so that it helps keep the turbine speed up.
ParmasThread starterML · May 23, 2009#106
Thanks for your info changchesoon I will consider recirculation if necessary... btw here are some shots from the ecu btw GoTech MFI proX (DATA WITHOUT ENGINE START)

8 attachments not included in this copy

ParmasThread starterML · May 23, 2009#107
Someothers

5 attachments not included in this copy

Nexus1155Dorchester · May 23, 2009#108
Hey chang when you say the fmanage, do you mean the F-con if so, which one, when i go onto ebay it looks like they are unprogrammable vehicle spacific... thanks for the help.
changchewsoonMalaysia · May 23, 2009#110
wow parmas, thanks for all the screenshots! think i'll need a while to go look at all of them, nice job by the way! :)

anyways, i've placed an order for a set of recirulation adapter for my SSQV. hopefully i will be able to get my recirculation done within 2 weeks time.

i will post up information here for sharing.
changchewsoonMalaysia · May 23, 2009#111
Originally Posted by Nexus1155 ↑
Hey chang when you say the fmanage, do you mean the F-con if so, which one, when i go onto ebay it looks like they are unprogrammable vehicle spacific... thanks for the help.
hi nexus,

the fcon is a product from HKS,the fcon IS and the fcon SZ are piggybacks while the fcon VPro is a standalone ems.

the f-manage is a product from trust, it is a wideband O2 monitor and it also allows you to tune your car's closed loop by modifying the air fuel ratio signal the ecu is currently receiving from your O2.

i came across in the magazines that the japanese and taiwanese are using the f-manage to control the closed loop feedback of the skyline R35 as the r35 runs a full time closed loop system even when you're on WOT.
cali yarisCanoga Park, CA · May 24, 2009#113
cool. Why does it run so rough?
supmetSouthern California · May 24, 2009#114
Originally Posted by cali yaris ↑
cool. Why does it run so rough?
haha, I was about to say "it looks like its about to shake a spark plug boot loose" and then 3 seconds later it did!
changchewsoonMalaysia · May 25, 2009#115
nice video!

by the way, i just want to share that although my tuner thinks that doing a recirculation is the fastest and easier way, he provided an alternate option if i wanted to stay venting to atmosphere which is to perform a MAF sensor relocation to a pre throttle body and post bov location.
ParmasThread starterML · May 25, 2009#116
Originally Posted by cali yaris ↑
cool. Why does it run so rough?
Motor running rich and idling is badly affected. Still working into it!

Also badly in need of upgraded rear mounting

Will update when I have more cash!
ParmasThread starterML · May 27, 2009#117
Just a thought where I can get some information about general ecu mapping and tuning. I want to consider tuning my engine myself but I need to get the know how when and why etc...

If any of you have any link to some website or if any of you is already a tuner himself could give me any tips would be much appreciated!
rob323Joyner, Brisbane · May 28, 2009#118
Originally Posted by changchewsoon ↑
nice video!

by the way, i just want to share that although my tuner thinks that doing a recirculation is the fastest and easier way, he provided an alternate option if i wanted to stay venting to atmosphere which is to perform a MAF sensor relocation to a pre throttle body and post bov location.
That will only work as long as the MAF doesn't also have the air temp sensor in it.
ParmasThread starterML · May 28, 2009#119
Today I tried to understand by myself how to manage fuel and ignition. Well the tuning is fair easy to control and to manage but there are some things I still don't understand.

First I am confused what is the difference between micro fuel injection and normal fuel injection?

What about Injectors constant and latency values? From where do I get them?

Acceleration map, sensitivity and decay?

Second how could I understand when the ignition map is ok at that particular rpm? (In the ignition map shows constant ignition on all rpm loads)

What about ignition angle and coil charge time? Is there any need to change?

What is the best to reference on the mainfold air pressure sensor or throttle position sensor?

I know there are many questions here but I would be pleased if some of you can make me understand more as much on these!
CASTREXCosta Rica · May 28, 2009#120
Not to pull you back.... but,

With ALL the money and time that you have invested on this car so far... are you going to cheap out on the most critical stage????

If I were you I would go for a Pro tune...
You know you can kill your engine with a bad tune?? It would be a shame!

Is cool if you want to learn about tuning... but perhaps you can pick up a beater car and practice on an engine that you wouldn't mind to screw up.


Just my 2cents
ParmasThread starterML · May 28, 2009#121
Originally Posted by CASTREX ↑
Not to pull you back.... but,

With ALL the money and time that you have invested on this car so far... are you going to cheap out on the most critical stage????

If I were you I would go for a Pro tune...
You know you can kill your engine with a bad tune?? It would be a shame!

Is cool if you want to learn about tuning... but perhaps you can pick up a beater car and practice on an engine that you wouldn't mind to screw up.


Just my 2cents
I totally agree with your response I just want to know if the tuner made everthing right regarding mapping and settings.

On the other hand if the tuner makes a bad tune himself I would be more shame to pay for his time (which is not cheap btw)

Also I am considering that if it happen to notice a misfire on a particular gear and rpm I would be able to set it myself.

I know I am not a tuner myself and I don't pretend to set all the rpm loads on all gears by myself
CASTREXCosta Rica · May 28, 2009#122
Good luck to you then! just be careful 👍
Nexus1155Dorchester · May 29, 2009#123
Originally Posted by Parmas ↑
Today I tried to understand by myself how to manage fuel and ignition. Well the tuning is fair easy to control and to manage but there are some things I still don't understand.

Tuning is very easy as long as you have the knowledge, i suggest you go onto boards like romraider or pgmfi and start reading up on guides, it will help you greatly

First I am confused what is the difference between micro fuel injection and normal fuel injection?

What about Injectors constant and latency values? From where do I get them?

You need to find out what the stock latency is(probably can do it with an oscilloscope, and measure pulsewidth? i dont remember how they do it from scratch), but settings the latency is the proper way to size injectors... if i recall its (new inj cc/old inj cc * old latency = new latency) or something like that, the formula is everywhere

Acceleration map, sensitivity and decay?

I'm taking this could be throttle sensitivity map, only thing ive ever seen with decay is knock so i wouldnt play with that or your car might be jittery, but sensitivity should be 100 across the board. You let your foot do the judgement, it will feel like a totally different car, my truck became a monster after, and remember its all based on load, so you won't go WOT from just tapping the gas

Second how could I understand when the ignition map is ok at that particular rpm? (In the ignition map shows constant ignition on all rpm loads)
Depending on if you are controlling ignition with your management unit, a constant value across all load is very bad. You could either be losing power/fuel/damaging the engine... they can usually get a basemap if its wired from the ecu, if not they can get one from another 1nz-fe engine map thats not the yaris

What about ignition angle and coil charge time? Is there any need to change?

What is the best to reference on the mainfold air pressure sensor or throttle position sensor?
please clarify a bit

I know there are many questions here but I would be pleased if some of you can make me understand more as much on these!
I tried to give pack as much info as i could with the time i have right now, i didn't comment on some things, because i don't think you need to worry about them or need them
ParmasThread starterML · May 29, 2009#124
Thanks for your answers ... here is the setup screen where you can select which load input the ecu has to refer on as primary input

You can refer to the previous page to see some screenshots maps from the ecu

1 attachment not included in this copy

Nexus1155Dorchester · May 29, 2009#125
Well if you don't have a map sensor installed you can only do it based off the throttle position sensor....

but if you do have a MAP sensor that you added, it should be TPS for whatever is out of boost and MAP for when it hits boost. So it would be one of the bottom two...
ParmasThread starterML · May 29, 2009#126
What do you think about ignition compared with fuel injection?

And btw what is micro fuel injection?

1 attachment not included in this copy

cali yarisCanoga Park, CA · May 29, 2009#127
Tuners here don't let the car leave until the job is good and complete. I heard your motor in the video. Hopefully your tuner is not saying he's completed the job? 🙁

As CASTREX correctly says, this is the most important step of the game, and if it's done WELL, you won't have to do very much at all, and especially you shouldn't have to correct or fix something the tuner did wrong.
Nexus1155Dorchester · May 29, 2009#128
It looks like a good management system, but it looks like it displays wacky, if it was just numbers it would be easier to view and easier to tune with. The injection looks fine, i don't know what AFR you are seeing, but ignition is wrong if in fact the harness is hooked up to control ignition...well see it also depends on how ignition is controlled on this management, thats whats weird, so i can't give you an exact answer, but on the video it definately sounds off if youre not cammed with a big lopey thing
ParmasThread starterML · Jun 7, 2009#129
I wish to understand exactly why my motor is running bad idling.. The idling of my motor sometimes varies from 800rpm to 1300rpm... well I want to know what is the thing that makes this and what is related to.

I know that it's probably a tune up problem but what could be the things the tuner should consider... ignition maybe fuel or a sensor?

So I ask, what electric and mechanical components in a setup like mine should affect idling? What things you guys suggest me to check?
ParmasThread starterML · Jun 17, 2009#130
Today got into discussion about the exhaust piping etc... and still not decided if dual or straight.

If a dual it would be Downpipe 2.5" / Middle Straight pipe 2.75" / Fish Tail 2.5" into same size inlet mufflers.

If single it would be Downpipe 2.5" / Middle Straight pipe 2.75" / Inlet muffler 3".

What do you guys suggest to choose in terms of performance?
ParmasThread starterML · Jul 1, 2009#131
I am interested in buying the Perrin fuel rail for my 1NZ and from this week I couldn't find it anywhere for sale. Any of you guys know where to find it or is there any other brand that makes fuel rails for our engine?
cali yarisCanoga Park, CA · Jul 1, 2009#132
I can get you the Perrin rail that's on my car if you want one, I'll get you a price.

4 cylinder? single exhaust. I have 2.5" all the way to the back, it's plenty of flow up to 20 psi.
ParmasThread starterML · Jul 2, 2009#133
Originally Posted by cali yaris ↑
I can get you the Perrin rail that's on my car if you want one, I'll get you a price.

4 cylinder? single exhaust. I have 2.5" all the way to the back, it's plenty of flow up to 20 psi.
What is the reason of sale Garm?
cali yarisCanoga Park, CA · Jul 2, 2009#134
sorry, I meant that I can get you one just like mine if you're interested.
The SpectacleTampa, FL · Jul 2, 2009#135
Originally Posted by cali yaris ↑
inline 4 cylinder? single exhaust.
this.
cali yarisCanoga Park, CA · Jul 2, 2009#136
Parmas, you want the rail only or with the regulator and gauge?
ParmasThread starterML · Jul 3, 2009#137
Originally Posted by cali yaris ↑
Parmas, you want the rail only or with the regulator and gauge?
That depends what regulator you are referring to?

Is it the same type and colour paint you are using in your setup?
ParmasThread starterML · Jul 14, 2009#138
AEM Tru Boost and Uego Controller installed on dash!

Also installed and completed Twister exhaust will post pics of it later on...

Next installation.. Flex a lite oil cooler and custom made radiator

2 attachments not included in this copy

cali yarisCanoga Park, CA · Jul 14, 2009#139
How's it running now?
ParmasThread starterML · Jul 14, 2009#140
Originally Posted by cali yaris ↑
How's it running now?
Well the exhaust really made a difference in power especially during boost. It feels better in accelaration and now I can hear correctly the BOV blowing off!

Still needs map correction but it's lot better and no backfire were heared aswell!

Will update more later on...
cali yarisCanoga Park, CA · Jul 18, 2009#141
how's the idle?
ParmasThread starterML · Jul 18, 2009#142
Idle still running roughly between 1200 and 1500. When the custom radiator is finished I will update with more info.

The best I can make now is a video WOT ! Thinking what area will be best for shooting it!
AlexNet0Rockland, ME · Jul 19, 2009#143
^please do, please please, WOT, video, lol
ParmasThread starterML · Aug 20, 2009#144
Finally gathered some cash and time to make more mods to the car. Mods consisted in custom intake and reinforced rear mounting of the engine.

Because of few space in the engine bay this was the only efficient position for the airfilter to be placed and came pretty as I expected.
Regarding the mounting, It was too late to make pics and of course in a hurry to try it out so better luck next time :)

In the meantime still in the waiting list for tuneup! I am hoping for next week :)

3 attachments not included in this copy

TamagoOff Grid · Aug 20, 2009#145
wow that's cramped! turbo in back + front mount = a pain in the ass... parmas, would you consider doing a top mount intercooler? you'll get better throttle response, less pressure drop, and an overall cleaner engine bay. if an STI can make 350whp+ on a top mount, so can you!
ParmasThread starterML · Aug 21, 2009#146
I have never considered a top mount intercooler since I never liked the design.

In my case if I decided to top mount the ic I am sure that all the heat of the engine and the turbo together will make the ic useless and in the worst case engine damage. I don't exactly care of space, I give priority to performance and efficiency...
TamagoOff Grid · Aug 21, 2009#147
Originally Posted by Parmas ↑
I have never considered a top mount intercooler since I never liked the design.

In my case if I decided to top mount the ic I am sure that all the heat of the engine and the turbo together will make the ic useless and in the worst case engine damage. I don't exactly care of space, I give priority to performance and efficiency...
so you're saying that WRC rally cars are useless? most rally cars use top mount intercoolers. subaru uses top mount

don't be a fanboi... front mounts are overrated.
TheRealEnthMiami, FL · Aug 21, 2009#148
Top mount FTW
cali yarisCanoga Park, CA · Aug 21, 2009#149
don't be a fanboi... front mounts are overrated.
pluses and minuses for both, but I always enjoy a good pissing contest, so carry on.
lilredrocketDFW, Texas · Aug 21, 2009#150
Haha.