Yarisworld Archive

"Parmas" Motor

490 posts · 124,989 views · page 7 of 10

Replies continued

ParmasThread starterML · Jun 17, 2010#301
Originally Posted by rob323 ↑
To me, it sounds more likely that the problem is the engine management, than the engine. Might be cheaper to use something like Adaptronic which utilises all the factory sensor & igniters and has continuously variable control over the vvti.

I'll pm you an email conversation I had with Adaptronic recently.
I checked the specs of the e420c and seem that VVTi isn't mentioned but as you sent me the pm it seems it can eventually.

I am going to give the last try to the present management if tuning fails again then I have to change it to another that accepts VVTi or I have to consider removing VVTi completely like many honda removing Vtec.... will see what comes up next
rob323Joyner, Brisbane · Jun 17, 2010#302
Yes, that was why I emailed them. To make sure.
I haven't played enough with these motors to find out just where the cam sits when the vvti solenoid is unplugged but maybe that is the best way for you to do it now unless you can get the continuously variable control working.
cali yarisCanoga Park, CA · Jun 17, 2010#303
^ we know that works too. Just not as much control in tuning.
Bluevitz-rsOshawa, Ontario, Canada · Jun 17, 2010#304
Originally Posted by rob323 ↑
Yes, that was why I emailed them. To make sure.
I haven't played enough with these motors to find out just where the cam sits when the vvti solenoid is unplugged but maybe that is the best way for you to do it now unless you can get the continuously variable control working.
It reverts to the 0° position.
rob323Joyner, Brisbane · Jun 17, 2010#305
So does the vvti just retard the cam, or advance it?
ParmasThread starterML · Jun 18, 2010#306
Originally Posted by rob323 ↑
So does the vvti just retard the cam, or advance it?
The VVTi retard and advance the camshaft angle based on the engine:

- RPM
- Temperature
- Load

If you see the image below you can notice that the camshaft is being advanced or retarding according these factors. Although there are six diagrams of camshaft angles, three of them are matched with others. I marked them for you to understand with ease.

It is hard to notice correctly if the overlaps are the same but if you see accurately, the camshaft angle figures are labeled with a 7-digit number. Some of them are actually the same label so it makes me think that infact they are at the same position.

So lets make a summary of this:

Camshaft Angle 1 - Fully Retarded

During idling \ Light Load (1a) = At Low Temperature (1b) = Upon Starting \ Stopping Engine (1c)

Camshaft Angle 2 - Fully Advanced

At medium Load (2a) = In low to Medium Speed Range with Heavy Load (2b)

Camshaft Angle 3 - Retarded but more advanced than Angle 1

In High Speed Range with Heavy Load


Still.... if you notice the 2nd and 3rd diagrams you will notice that the valve has only two ports and not three, which I am thinking are Angles 1 and 2. So that makes me think, where would the valve be at Angle 3?

3 attachments not included in this copy

Yaris HiltonBristol, Tennessee, USA · Jun 18, 2010#307
Got a link to that 1NZFE Spec Details.pdf document?
ParmasThread starterML · Jun 18, 2010#309
Originally Posted by cali yaris ↑
The AEM EMS has a wizard for Toyota motors, I believe it automatically sets parameters for VVTI. So I'm not sure I'll be able to answer your question, but Art is going to look into it further.
Garm I have an idea..... if we connect an oscilloscope on the signal wire of the valve timing control on a stock 1NZFE with a stock ecu, we could know eventually the frequency and duty cycle at all rpm ranges.

The problem is I don't own one damn... or else someone could check with a toyota expert on this .... maybe H3ilton 🙄


Edit: I found a waveform of the camshaft timing valve here on page 33 http://www.etimago.com/yaris/repairm...%20Control.pdf

Can anyone translate it in terms of frequency or duty cycle?

I uploaded some pages of the manual that relates to VVT information

4 attachments not included in this copy

cali yarisCanoga Park, CA · Jun 18, 2010#310
wow, now that is over my head, sorry!
ParmasThread starterML · Jun 19, 2010#311
I told this to a friend and he said that from the look of the waveform he concludes that it is at:

Frequency 1000Hz because frequency = 1 \ t and since the waveform shows 1ms\div so = 1 \ 0.001s = 1000Hz

Duty 33% because the waveform shows 3 pulses each about a bit longer than each division. Since there are 10divisions and 3 pulses (each a bit longer) ......... so 1pulse = 1.1 x 3 = 3.3.... 3.3div out of 10div = 33%

Garm can your tuner confirm this?
cali yarisCanoga Park, CA · Jun 19, 2010#312
I haven't heard back yet 🙁
ParmasThread starterML · Jun 19, 2010#313
Explained more in detail from where these values came.... if there is a mistake don't hesitate to post why and of course the right answer :)

By the way previous tuner set these values to 60Hz and 7.1% in which if the "new" values are correct, with the present values I have on my ecu there is a high possibility that the valve is never being activated and it is always on the most retard state at all loads and rpm!!! that explains roughy state etc...
rob323Joyner, Brisbane · Jun 20, 2010#314
I don't think your frequency value is correct. If each division is one millisecond (which isn't entirely clear), then each pulse appears to be about 3.5 milliseconds apart, which correlates to approx. 285Hz. I agree with the 33% duty cycle amount though.
Yaris HiltonBristol, Tennessee, USA · Jun 20, 2010#315
Thanks for the link, Parmas!
ParmasThread starterML · Jun 21, 2010#316
Update:

Today I went to my tuner and we began to check the Stock Crank Trigger in order to configure the ecu accordingly. We found out that the stock toyota crank sensor has a sense config of 37 -3 (Please anyone confirm this) in which the present ecu do not accept this triggering. Infact the ecu is configured to 36 -1 which do not represent my setup....

Please garm or anyone can you confirm this 37-3 triggering?
rob323Joyner, Brisbane · Jun 21, 2010#317
I can confirm from my Echo manual that it has 34 teeth, so your 37-3 config might be correct.
ParmasThread starterML · Jun 21, 2010#318
Originally Posted by rob323 ↑
I can confirm from my Echo manual that it has 34 teeth, so your 37-3 config might be correct.
Thanks rob that relievs me from doubts!

Anyother who wish to confirm this trigger feel free especially garm 🙂
Bluevitz-rsOshawa, Ontario, Canada · Jun 21, 2010#319
It's actually 36 minus 2.

This is info coming from a Toyota Canada Technician Trainer.

Edit: So there should be 34 teeth, but only minus 2, not 3.
ParmasThread starterML · Jun 22, 2010#320
Originally Posted by Bluevitz-rs ↑
It's actually 36 minus 2.

This is info coming from a Toyota Canada Technician Trainer.

Edit: So there should be 34 teeth, but only minus 2, not 3.
As of Bluevitz post we decided to re check again and count the teeth again. I didn't mention before but we have not opened the motor to count it directly but we are counting them from the crank sensor hole so there is a possibility we counted 1 missing tooth more.

It is strange the uneven number of 37 so we conclude that the trigger is effectively 36 -2 as Bluevitz-rs mentioned
ParmasThread starterML · Aug 7, 2010#321
I have a problem regarding the IDLE control connection. Do anyone knows where I can find a diagram showing the idle control connector and it's terminal connections.

The connector is 3 wire : Red/Black Yellow/Black Brown


I need this to connect it to the standalone ecu.

2 attachments not included in this copy

ParmasThread starterML · Aug 12, 2010#322
UPDATE:

Wiring is almost ready .... the only things remaining is Launch control and Table switches to wire up. Also changing some oil and water braided pipes to some anodized color threads which look awesome for me.

I didn't bother taking pics since you would only see a mess of wiring which still needs to be organized.

Stay tuned!
cali yarisCanoga Park, CA · Aug 12, 2010#323
I want to see the mess of wiring! Pictures always! 🙂
ParmasThread starterML · Aug 13, 2010#324
Originally Posted by cali yaris ↑
I want to see the mess of wiring! Pictures always! 🙂
YOU WANT PICS HERE THEY ARE 😁

By sequence:

1. 4 x Haltech Igniton modules . 1 Ignitor per coil for maximum energy efficiency

2. Honda CBR600 Coil with custom made rubber cushion at the top. Grommet of a stabilizer link haha

3. Coil Setup. Please note that coils are not tighten, that's way there is a gap!

4. Front View.... still way to go for a clean setup

5. The box of my dreams 🙂

6. Ohhh myyy ... a day of work to clean the mess

Cheers

6 attachments not included in this copy

changchewsoonMalaysia · Aug 13, 2010#325
parmas nice work! and i can see you're running the haltech platinum sport ecu! good choice...
Focus_Sh1ftNew Jersey · Aug 13, 2010#326
Tbh, my head exploded looking at that last picture.
cali yarisCanoga Park, CA · Aug 13, 2010#327
LOL, that's the easy part!

Thanks for posting, that makes it fun to check the thread!! 🙇
scioncrewHB · Aug 13, 2010#328
that remines me of your car Garm :)
cali yarisCanoga Park, CA · Aug 13, 2010#329
^ YES!! 😁 see the influence you've had?
ParmasThread starterML · Aug 13, 2010#330
Thanks for the comments I really need to cheer up since the most irritant part is coming..... Organizing all the mess! By the way this time I am doing all my way, no tuner is involved here, it's only my work of art. Then up on the dyno goes to the professionals and I am hoping for some nice numbers.

As a brief all the sensors, idle control, injectors and ignition is wired up. Tomorrow I will begin testing out the setup beginning from the coils. If ignition shows good spark I will give a try to start the engine at least, then tune it on dyno.

Looking into the Haltech software shows much more details... from gauges to 3D graph maps. Main Settings are unlimited which can probably control any type of engine out there. It also support Ivtec or VVTL-I at full setting with fuel and ignition maps only for them. Will take pictures of software as soon as all is done.
ParmasThread starterML · Aug 14, 2010#331
Update:

Spent a day working on wiring and on the engine bay part wiring is complete although I need to figure out a nice plate to hide the side wiring.

Also arranged inside wiring but ran out of cable ties so I had to stop 😠

Spark was tested on all 4 coils and ignitors with the help of my gf cranking the engine 🙂 . All gave a good spark so ignition is ok.

Next.... still need to complete in car wiring and installing launch control toggle switch. If there is more time I will try starting the engine and prays god all goes well 🙇

Stay tuned!

4 attachments not included in this copy

changchewsoonMalaysia · Aug 16, 2010#332
hi parmas, now that you're using the haltech platinum sport ecu may i entice you with this?

it plugs straight to the ecu via a single vnet cable and it displays everything the ecu sees...

Video: http://www.youtube.com/watch?v=QajCrfAmxEU
Link 1: http://www.viosturbo.com/2010/04/sta...ch-iq3_24.html
Link 2: http://www.viosturbo.com/2010/05/sne...play-dash.html

im very sure you'll definitely fall in love with it 😁 😁

5 attachments not included in this copy

cali yarisCanoga Park, CA · Aug 16, 2010#333
mmmm... I'll do a digital dash in the future for sure.
ParmasThread starterML · Aug 17, 2010#334
The display is cool but now I am not in the mood for more expenses.

If the engine reacts well with the combined ecu I will sure invest more on the car.... if not ( and prays god nooo) I have to sell the engine and go back to stock.
changchewsoonMalaysia · Aug 17, 2010#335
parmas don't give up yet, garm and i and lots of other people have been getting positive outcomes with the 1nz-fe engine.

we're here to help and share if you ever need anything man!
pimp my yarischicago · Aug 17, 2010#336
Holly heat wrap batman. That looks like an awsome project. Sweet display.
ParmasThread starterML · Aug 18, 2010#337
Originally Posted by changchewsoon ↑
parmas don't give up yet, garm and i and lots of other people have been getting positive outcomes with the 1nz-fe engine.

we're here to help and share if you ever need anything man!
I appreciate this comment. People like you make me struggle for success 🙂
ParmasThread starterML · Aug 23, 2010#338
Today changed engine oil and coolant and installed the "NEW" Teflon braided pipe for the turbo water line. Also all in cabin wiring is finished and arranged it like it never been there 🙂.

During the turbo water line installation I came to notice that the idle control on the throttle body has the coolant pipes missing (In and Out). Then I understood that these were being used to feed coolant to the turbo from the beginning. So I ask are these essentially needed for the idle control to work fine also since I changed the engine management? What are the consequences of these removed?

Also I need to know some information on the Idle control like frequency and normal operating conditions. I attached a screenshot of the page of the ecu software to set this up

1 attachment not included in this copy

cali yarisCanoga Park, CA · Aug 23, 2010#339
I know I'm not using those on my TB
ParmasThread starterML · Aug 27, 2010#340
Today I tried to start the engine but it seems there is something blocking the startup since it is stopping cranking after only few seconds.

I tried to increase fuel on the rpm range but still no start. After I came across this describtion of the starter on the manual and it says :

"IN CASE THAT THE STARTER BEGINS TO OPERATE, BUT CANNOT DETECT THE ENGINE SPEED SIGNAL, THE ECM WILL STOP THE STARTER OPERATION IMMEDIATELY"

Then I began to think that since I am operating the starter through the stock toyota ecu and I disconnected the engine speed signal (which is the Crank Trigger Sensor) and connected it to the Haltech Ecu, the stock ecu is surely not detecting the crank trigger and is probably stopping startup. I am not sure about this but it could be plausable.

Now I decided to eliminate the starter by using an external relay and a push button.

Although I am not sure about this so Garm or any other that has changed their ecu should tell if this is true or not.

1 attachment not included in this copy

ParmasThread starterML · Aug 28, 2010#341
Here is the current setup

1 attachment not included in this copy

ParmasThread starterML · Aug 28, 2010#342
I would like the experts to confirm with me about the Triggering of the engine in relation to Camshaft position.

Main needs are:

1. Trigger Angle

2. Tooth Offset between crank trigger and camshaft trigger

3. Trigger / Home Edge

1 attachment not included in this copy

ParmasThread starterML · Sep 15, 2010#343
All is ready and prepared for the dyno tune. It is scheduled to be within the next week so cross hands all goes well to jump to some nice numbers.

I think I finally earned this after 2 years owning the engine it has not passed 500miles on it!

The only thing remaining is putting on the bumper in place and we are ready to go.

1 attachment not included in this copy

pimp my yarischicago · Sep 15, 2010#344
Looks good. All Business.🤤
changchewsoonMalaysia · Sep 19, 2010#345
time to make some serious power parmas, can't wait to see the numbers on the dyno!
cali yarisCanoga Park, CA · Sep 19, 2010#346
CLEAN - you are ready!
ParmasThread starterML · Oct 28, 2010#347
Car was brought to the tuning facility for tuning.

For a change we had trouble keeping the engine on idle and was misfiring as hell. The tuner said that probably it is something related to the camshafts \ VVti activation position etc...

We brought another standard engine to compare values of crank triggering versus camshaft positions etc... which are still working on it.

Tomorrow will check the intake manifold and throttle body for leaks just in case. Also need to change the oil turbo feed line since the tuner said it is too wide than normal condtions.

I would like to know what happens to the camshaft position if you disconnect the Cam timing plug (near the alternator) . Would it become fully retarded or fully advanced or a certain degree?

This answer will help the tuner much with his issues!
Bluevitz-rsOshawa, Ontario, Canada · Oct 28, 2010#348
^ unplugging the VVTi solenoid leaves the cam at 0°. So no advance.
advocatelocation · Oct 29, 2010#349
Parmas,

That haltech digital dash is absolutely stunning.

I saw one of these in a rally car the other day and figured I would never be able to have anything nearly as cool as that in my car so seeing it in front of your dash has made me really excited to start working on my engine once the funds become available.

Keep going strong man we're rooting for you.
ParmasThread starterML · Oct 29, 2010#350
Originally Posted by advocate ↑
Parmas,

That haltech digital dash is absolutely stunning.

I saw one of these in a rally car the other day and figured I would never be able to have anything nearly as cool as that in my car so seeing it in front of your dash has made me really excited to start working on my engine once the funds become available.

Keep going strong man we're rooting for you.
I agree with you on the digital dash although you missed that was only an opinion of changchewsoon. I don't own it at this time.

🙂