My radiator runs full width, it's really too good, the car runs a little too cold when the ambient temps are under 80 degrees outside.
"Parmas" Motor
490 posts · 124,989 views · page 10 of 10
Replies continued
time to move the battery to the back of the car. It'll help to offset some of the added weight and free up an additional 1 cubic foot of space for more stuff 🤘
The highest I've seen is 104 degrees C. Are you running an oil cooler Parmas? That should help the water temps a bit too.Originally Posted by Parmas ↑. I was seeing 90C and over with the fan on.
Still not tried the setup yet cannot tell for now that the extra rad and fan how much they are better. The Water Temps are measured after the water outlet of the engine.
No I love the battery there and I really need to stop modifiying the engine cause I better put some cash on brakes and suspensions!
No oil cooler, the oil temps are about 60 - 70 C the max I seen. That is already good that way. Also I don't want to have pressure loss....
No I love the battery there and I really need to stop modifiying the engine cause I better put some cash on brakes and suspensions!
No oil cooler, the oil temps are about 60 - 70 C the max I seen. That is already good that way. Also I don't want to have pressure loss....
That's an urban myth and isn't a problem if it's done right.Originally Posted by Parmas ↑Also I don't want to have pressure loss....
I'm surprised at how low your oil temps are, especially if your water temps are high.
+1 on the suspension.
I confirm the oil temps are seeing maximum of 65C Degrees under load.Originally Posted by rob323 ↑I'm surprised at how low your oil temps are, especially if your water temps are high.
Today I tried the engine on street and pushed it on gears above 6Krpm. I can notice a great benefit with the extra radiator and fan. The max temp seen 91C Degrees and cooled down quickly to 85C in just a minute of the fans on.
I need to fine tune the fuel map and Cam timing and then off to the dyno to check powerband and torque accross the rpm range. Cross Fingers! 🤘
If you don't mind me asking how much did u sink in this thing already?
If you are referring to money ...well all I can say is that I spent much more than I expected but I have more than I thought aswell!Originally Posted by Yoda ↑If you don't mind me asking how much did u sink in this thing already?
Any updates, or dyno numbers?😁
Dyno is scheduled on 29 August and I hope some good numbers at the wheels.Originally Posted by johnny_vitz ↑Any updates, or dyno numbers?😁
I am a bit worried how much boost and revs I am going to give her because of the stock head so if any would give a heads up of a limit just post it here...
During the time I found a good deal on a set of D2 racing shocks. They are extremely sensitive on street and I can feel every little bump on the street (not comfortable at all) but at least rock solid on street corners.
Also I am having less wheelspin when giving her full throttle from a stop sign 😁
Here is the update:
6 attachments not included in this copy
Boost as much as your fuelling is good for! I have stock head and head bolts too. 7300 rpm has been just fine. I can vouch that the stock head can withstand past 8000rpm as I accidentally found out twice ( dropped it in 2nd instead of 4th on the dragstrip.. whoops ). I wouldn't set it at 8000rpm though lol. My factory tach won't read past 8000rpm so Im not too sure what it went too. Is It bad when the 1nzfe sounds like an F1 engine? jk.Originally Posted by Parmas ↑Dyno is scheduled on 29 August and I hope some good numbers at the wheels.
I am a bit worried how much boost and revs I am going to give her because of the stock head so if any would give a heads up of a limit just post it here...
During the time I found a good deal on a set of D2 racing shocks. They are extremely sensitive on street and I can feel every little bump on the street (not comfortable at all) but at least rock solid on street corners.
Also I am having less wheelspin when giving her full throttle from a stop sign 😁
Here is the update:
Set it at 7300 if it still makes power.
I just looked at your picture few posts above... make sure your pipes are bead rolled or the dyno session may get pricey if they have to keep putting back blown off intercooler pipes. May be fine at the boost you're at now........
I'm excited for you, looking forward to some great numbers!!
I can say for certain that the valve train won't keep up for long past 8000. I did the same thing once only I was on a road trip passing a couple gravel truck and somehow managed to pull it to second from the limiter in 3rd. Motor went to 8600 and sounded like someone through gravel inside the engine. 3 bent valves was the result. Luckily the motor kept running and I made it there >another 200km. The funniest part was that it didn't even set a misfire code or anything.Originally Posted by Blown_xa ↑Boost as much as your fuelling is good for! I have stock head and head bolts too. 7300 rpm has been just fine. I can vouch that the stock head can withstand past 8000rpm as I accidentally found out twice ( dropped it in 2nd instead of 4th on the dragstrip.. whoops ). I wouldn't set it at 8000rpm though lol. My factory tach won't read past 8000rpm so Im not too sure what it went too. Is It bad when the 1nzfe sounds like an F1 engine? jk.
Set it at 7300 if it still makes power.
I just looked at your picture few posts above... make sure your pipes are bead rolled or the dyno session may get pricey if they have to keep putting back blown off intercooler pipes. May be fine at the boost you're at now........
So wouldn't go past 7500 on the stock top end.
Thanks for the help guys but I really care about this motor and I prefer being safe than having a wrecked motor for just a few more rpm.
I am thinking of let it run from 6500rpm till 7000rpm and see if it will keep making power and torque on the stock head.
I am thinking of boosting till 16psi for now and see how it goes after trying it on the drag strip.
The main issue in this country is fuel octane since you don't get constant octane from the station. I will be using the Lucas octane booster to tune and keep giving her every refuelling to be safe.
The other issue is tire traction and wheel spin from a stop. The tires are Toyo R888 rally semi-slick tires but still having wheelspin above certain rpm launches. I am trying to set a launch control switch to help with this issue.
I am thinking of let it run from 6500rpm till 7000rpm and see if it will keep making power and torque on the stock head.
I am thinking of boosting till 16psi for now and see how it goes after trying it on the drag strip.
The main issue in this country is fuel octane since you don't get constant octane from the station. I will be using the Lucas octane booster to tune and keep giving her every refuelling to be safe.
The other issue is tire traction and wheel spin from a stop. The tires are Toyo R888 rally semi-slick tires but still having wheelspin above certain rpm launches. I am trying to set a launch control switch to help with this issue.
Today was the dyno day and we succesfully managed to get 210WHP @ 6800rpm and 184 torque at 5000rpm on the wheels with only 10psi of boost. We had some trouble with the AEM tru boost controller which wasn't increasing boost as it should be. I am sure that with 14 psi we could have managed 250WHP with stock cams / head internals.
The car was tried on street and got wheel spin issues till 3rd-4th gear. Now I need some serious rubber and I am thinking of a an AVON/Mickey Thompson slicks. I don't know if the drive shafts will hold the load on the drag strip so any feedback from boosted yaris owners with slicks are likely appreciated! Also what rim + tire size should I use to combine it with the C160 6spd 4.5:1 transmission?
http://www.youtube.com/watch?v=9jCzU3sU53w
The car was tried on street and got wheel spin issues till 3rd-4th gear. Now I need some serious rubber and I am thinking of a an AVON/Mickey Thompson slicks. I don't know if the drive shafts will hold the load on the drag strip so any feedback from boosted yaris owners with slicks are likely appreciated! Also what rim + tire size should I use to combine it with the C160 6spd 4.5:1 transmission?
http://www.youtube.com/watch?v=9jCzU3sU53w
First of all CONGRATS on reaching this landmark! I know the project has been a challenge but your persistence is paying off!
You should be able to burnout and launch in 2nd gear for best drag results. Does your management allow you to program a 2-step?
I'll go check what wheels/tires I am running for drag racing, I think they work really well.
You should be able to burnout and launch in 2nd gear for best drag results. Does your management allow you to program a 2-step?
I'll go check what wheels/tires I am running for drag racing, I think they work really well.
managed to get 210WHP @ 6800rpmWhat did the curve look like up top?
Thanks garm I really appreciate your feedback.Originally Posted by cali yaris ↑First of all CONGRATS on reaching this landmark! I know the project has been a challenge but your persistence is paying off!
You should be able to burnout and launch in 2nd gear for best drag results. Does your management allow you to program a 2-step?
I'll go check what wheels/tires I am running for drag racing, I think they work really well.
Yes the ecu is capable of a 2 step launch control and there is actually a switch installed on the handbrake to enable it when I want to. This was never tried since it was installed recently so I am not sure which are the correct ignition retard timing and enrichment settings for a good launch on the strip.
I would probably try your advice of 2nd gear and begin with launch control from 5000rpm -20 Degrees ignition till I get it right.
Next friday I booked for a Japs nightout drag strip so I am trying to get an average quarter mile time.
my two-step is programmed to flood the exhaust mani and build boost for launch at 16 psi. I don't think we changed the timing just for that.
I launch at 5500, but 5000 will probably be fine too. The slicks change things a LOT, you can launch much harder. I'm still getting used to that. 🙁
I launch at 5500, but 5000 will probably be fine too. The slicks change things a LOT, you can launch much harder. I'm still getting used to that. 🙁
The curve inreases gradually until reaching 6800rpm. Above that range there wasn't any gain on power just a constant peak 211BHp till 7000rpm.Originally Posted by cali yaris ↑What did the curve look like up top?
I should be able to get a curve printout for your reference.
What slicks brand are you using and rim size/profile/wide measurement?
I came across a friend which have a new race gate (external wastegate) for sale on a bargain price. He intended to put it into his own but scrapped the idea.
The race gate is 38mm and with an unknown spring pressure = unknown lowest boost pressure, BUT that is not a problem right now.
The problem is LIMITED SPACE to put it in mate to exhaust manifold and downpipe which is really a complicated thing to do....
This gate would cost me the price of its own + fabricating custom work + hassle of bumping into other fuel / oil / water / cable components so after all this I ask >>>
1 . IS IT WORTH THE HASSLE OF DOING THIS?
2. WHAT ARE THE ADVANTAGES AND DISADVANTAGES OF THIS GATE VS INTERNAL?
3. WOULD THE ENGINE BE AT ANY RISK OF BOOST SPIKES BY KEEPING THE INTERNAL WASTEGATE?
CHEERS
The race gate is 38mm and with an unknown spring pressure = unknown lowest boost pressure, BUT that is not a problem right now.
The problem is LIMITED SPACE to put it in mate to exhaust manifold and downpipe which is really a complicated thing to do....
This gate would cost me the price of its own + fabricating custom work + hassle of bumping into other fuel / oil / water / cable components so after all this I ask >>>
1 . IS IT WORTH THE HASSLE OF DOING THIS?
2. WHAT ARE THE ADVANTAGES AND DISADVANTAGES OF THIS GATE VS INTERNAL?
3. WOULD THE ENGINE BE AT ANY RISK OF BOOST SPIKES BY KEEPING THE INTERNAL WASTEGATE?
CHEERS
Not sure it's worth it. Nice to be able to change out the spring (or the whole thing) when needed for the boost you are going to run. But if you're using a boost controller, you should be somewhat protected from surges and spikes either way.
I think that at your current position with the project, it's not a top priority to re-do a bunch of stuff.
I think that at your current position with the project, it's not a top priority to re-do a bunch of stuff.
as the saying goes, "dont fix what already works"..
From what i know:
advantages of external
1)better boost control
2)less backpressure
3)lower EGTS
advantages of internal
only cheap
I ordered an emusa external for my tsport turbo as well 😉
advantages of external
1)better boost control
2)less backpressure
3)lower EGTS
advantages of internal
only cheap
I ordered an emusa external for my tsport turbo as well 😉
You forgot the disadvantages ! :)Originally Posted by Paris vvt-i ↑From what i know:
advantages of external
1)better boost control
2)less backpressure
3)lower EGTS
advantages of internal
only cheap
I ordered an emusa external for my tsport turbo as well 😉
My only issues in regards with the external wastegate is :
1. limited space to fit it on my custom manifold
2. A hassle of more hot pipes under the hood !
1 attachment not included in this copy
sooooo.... is your wheel hop eliminated yet? 😁
No Sir, I didn't have time to work on it since I am solving some other issues regarding high idle. It seems that the 2ZZ throttle body I bought this year has actually more air breathing than expected because of some wear and tear on the butterfly.Originally Posted by cali yaris ↑sooooo.... is your wheel hop eliminated yet? 😁
I am waiting for another and hope it is good this time !
I never knew I would have all these issues! 😠
It never stops. I just did this to my clutch:
Picture not included in this copy
Picture not included in this copy
wow, I have never seen a pressure plate break in half! Looks like a 6 puck? Thought you had exedy stage 2?
I had Exedy Stage 1 a long time ago. The picture is a Clutchmasters Stage 4!
OUCH!! How much did km did you do with that clutch ?Originally Posted by cali yaris ↑I had Exedy Stage 1 a long time ago. The picture is a Clutchmasters Stage 4!
I tought clutchmasters are good though!
Its time for a new better one !
Will the below fit the yaris :)
1 attachment not included in this copy
^ It was on the car well over a year, with a lot of street driving, some track dates and some drag racing.
Clutchmasters makes a very good twin disc, as you show above. But you are still looking at a minimum of $1200. Even as a dealer, I decided I can't afford to go that far with it.
CM was good enough to build me a new Stage 4 with 300-400 more pounds of pressure. Should last a good long while.
I'd rather have the clutch break first -- better than the transmission.
Clutchmasters makes a very good twin disc, as you show above. But you are still looking at a minimum of $1200. Even as a dealer, I decided I can't afford to go that far with it.
CM was good enough to build me a new Stage 4 with 300-400 more pounds of pressure. Should last a good long while.
I'd rather have the clutch break first -- better than the transmission.
Agree on the transmission quote ...Originally Posted by cali yaris ↑^ It was on the car well over a year, with a lot of street driving, some track dates and some drag racing.
Clutchmasters makes a very good twin disc, as you show above. But you are still looking at a minimum of $1200. Even as a dealer, I decided I can't afford to go that far with it.
CM was good enough to build me a new Stage 4 with 300-400 more pounds of pressure. Should last a good long while.
I'd rather have the clutch break first -- better than the transmission.
Although I would thought it would last longer for sure!
Mine was bought used which only god knows how much miles had. Stage 3 Spec clutch and still clamping hard after 4 years 🙂
Do you think its possible, that being there are only a handful of people who run 350+ whp on a 1nz motor, that the disigners probably laughed when someone said, "lets make a stage 4 for a 1nz". Then got bored and half-assed it because in thier mind they are chuckling, that 1nz will blow up before this clutch see's a flywheel.
just a scenario played thru my head when I saw Garms attachment.
just a scenario played thru my head when I saw Garms attachment.
Stage 3 Spec clutch and still clamping hard after 4 yearsWhich includes about 3 years of down time? LOL Just saying.
There are plenty of pictures of fried Spec clutches out there too. I don't think it's the brand. A CM Stage 2 lasted 3+ years on my 450 whp Scion tC - go figure.
@ilikerice -- maybe, but I doubt it. Clutchmasters is a serious company, and not as large as you'd think.
It's possible the pressure plate was defective or warped, then failed suddenly. The good news is that they stepped up and took care of me; just like I do with my customers. 👍
yea yea, I was kidding. i agree. I was just thinking of a funny skit that would be funny. I know they are very reputable and that is awesome that they are taking care of you like that. 🎉Originally Posted by cali yaris ↑
@ilikerice -- maybe, but I doubt it. Clutchmasters is a serious company, and not as large as you'd think.
It's possible the pressure plate was defective or warped, then failed suddenly. The good news is that they stepped up and took care of me; just like I do with my customers. 👍
WOW. Never seen that happen before.Originally Posted by cali yaris ↑It never stops. I just did this to my clutch:
Picture not included in this copy
I hope that was just a defective plate or something considering the tC currently has the same clutch + more power 😛
Really glad to hear CM got behind their product though. That's how it should be.
Also Parmas - I think it goes without saying that there's pretty much always going to be issues when you have such a heavily modified car. A small (although sometimes large lol) price to pay for a good time. 👍
Maybe 2 years of downtime but when it goes out I surely abuse the most out of it!Originally Posted by cali yaris ↑Which includes about 3 years of down time? LOL Just saying.
There are plenty of pictures of fried Spec clutches out there too. I don't think it's the brand. A CM Stage 2 lasted 3+ years on my 450 whp Scion tC - go figure.
@ilikerice -- maybe, but I doubt it. Clutchmasters is a serious company, and not as large as you'd think.
It's possible the pressure plate was defective or warped, then failed suddenly. The good news is that they stepped up and took care of me; just like I do with my customers. 👍
Should been a defect since I like clutchmasters and I am happy to see they are actually caring for their customers !
Have had my ACT 6 puck for almost 3 years... so far so good. Car had 99,000 on it when it went in, have 134,000 now. I have done a whole lot of racing.