Yarisworld Archive

"Parmas" Motor

490 posts · 124,989 views · page 2 of 10

Replies continued

ParmasThread starterML · Apr 8, 2009#51
Originally Posted by eTiMaGo ↑
Parmas, I see your engine has a separate distributor for the spark plugs, was this stock on your car?
No it was upgraded to a coil pack setup which normally used on a ferrari 360 😲
rob323Joyner, Brisbane · Apr 8, 2009#52
How are you increasing the fuel pressure in relation to boost pressure if you are not using an aftermarket fpr?
ParmasThread starterML · Apr 9, 2009#53
Originally Posted by rob323 ↑
How are you increasing the fuel pressure in relation to boost pressure if you are not using an aftermarket fpr?
The stock regulator is capable of handle a good amount of fuel at 17psi max. When exceeding the 17psi then you need an aftermarket one (at least on the old yaris version)
rob323Joyner, Brisbane · Apr 9, 2009#54
But the stock reg can't increase the fuel pressure to compensate for boost as it doesn't reference manifold pressure. I don't have access to my manuals atm, what is the stock fuel pressure for an echo?
cali yarisCanoga Park, CA · Apr 9, 2009#55
^ I have to agree, it doesn't quite make sense.
ParmasThread starterML · Apr 9, 2009#56
Originally Posted by rob323 ↑
But the stock reg can't increase the fuel pressure to compensate for boost as it doesn't reference manifold pressure. I don't have access to my manuals atm, what is the stock fuel pressure for an echo?
Well when I began my project I was about sure I was in need of an aftermarket regulator. Infact I was going to order an RS5 cosworth regulator until my mech had news from somewhere abroad that the stock one can handle the setup of 1Bar boost. I don't know the exact details, all I know is that if I decide to increase boost, the regulator needs to be replaced aswell.
cali yarisCanoga Park, CA · Apr 9, 2009#57
stock pump and regulator will get you to about 10 psi. Art's xB gave up at that level.
rob323Joyner, Brisbane · Apr 9, 2009#58
If the stock fuel pressure is say 40 psi (just a guess) and you plan on running 10 psi of boost, you should take your injectors out and get someone to flow them at 30 psi (40 minus 10) to make sure they are still atomising correctly otherwise fuel economy and power will suffer and you will probably find that you are maxxing out the duty cycle of the injectors early due to insufficient fuel pressure behind them.
ParmasThread starterML · Apr 22, 2009#59
Today tuneup was finally scheduled for next saturday... During some discussion about my turbo setup, we noticed that the rear mounting needs to be upgraded since the space between the turbo and brake divider lines is only about 2cm. Also need to adjust clutch pedal since it immediately works after you begin to release pedal.

In the meantime these were installed:
- G-tech gauge + G-force sensor
- Dedicated pc for engine management
- Motorized lcd
- AEM boost controller
- Ice wiring system

Will update with some pics next week
ParmasThread starterML · May 2, 2009#60
Well tune up was tried this week and we could not get the most out of it because of the stock regulator (reached 250whp). Although during the tune up session the vertical link suffered overheating and needs replacement.

Yesteday I made a video for your reference although it needs a better tuneup and lots of shielding.

http://www.youtube.com/watch?v=mfzzY...e=channel_page

I will post a better one when the tuneup is 100% complete
cali yarisCanoga Park, CA · May 2, 2009#61
What's a vertical link?

congrats on your tune so far! (told ya about about the limits of the regulator!)
AlexNet0Rockland, ME · May 2, 2009#62
Originally Posted by Parmas ↑
... of the stock regulator (reached 250whp). ...
HOLY crap
cali yarisCanoga Park, CA · May 2, 2009#63
yeah he should get well over 300 with what he's doing... 👏 🙇
ChinoCharlesOH · May 2, 2009#64
One day... one day.

Nice work thus far man!
AlexNet0Rockland, ME · May 2, 2009#65
Originally Posted by cali yaris ↑
yeah he should get well over 300 with what he's doing... 👏 🙇
jesus, cant wait to see BOTH of your motors at the end of tuning 👏👍
ParmasThread starterML · May 2, 2009#66
Originally Posted by cali yaris ↑
What's a vertical link?

congrats on your tune so far! (told ya about about the limits of the regulator!)
The vertical gear link is the one that shifts into gears while the horizontal link is the one that let you select from neutral to any other gear you want. Well I don't know how we could miss this since the link is only few cm behind the exhaust mainfold! Although this will be solved by installing some heat sheath aluminised sleeving around the links.

I don't know about the new yaris mounts but I am sure that the old yaris needs an upgraded rear mount because at that power and above 5000rpm the engine really make large moves to the rear. Make sure you consider this before swapping engines... although that is just a tip!

Next installation will mainly consider in heat managment and insulation like:

- Heat screen
- Exhaust Wrap
- Locking metal ties

All branded DEI. I am still not decided on an oil cooler yet! so if anyone has any tips please post :) BTW motor turned out of running 16psi @ 250whp still not 100% :)
cali yarisCanoga Park, CA · May 2, 2009#67
So you went up to 16 psi to make 250 whp? cool

I'm going with TRD front engine mounts and a C-One rollstopper in the rear.
ParmasThread starterML · May 6, 2009#68
Today went to the stainless crafter and decided to make some more modifications within the next month. These will consider into completion of the exhaust, some exhaust tips and harder mounting on the rear. Also an Aluminium INTAKE MAINFOLD will be made and installed within the next few month maybe will get to 25psi and 350hp!😳😁

BTW I am considering in upgrading the valve springs to harder ones (maybe ones of a celica will be good fitted there) and maybe also the valves to few larger ones. What do the experts think about this?
justjesusOrange County · May 6, 2009#69
Originally Posted by AlexNet0 ↑
jesus, cant wait to see BOTH of your motors at the end of tuning 👏👍
What are you talking about? I only have ONE motor, and it's not being tuned.
JUST KIDDING ! !😁

Nice job, Parmas 🎉
changchewsoonMalaysia · May 7, 2009#70
Originally Posted by Parmas ↑
The vertical gear link is the one that shifts into gears while the horizontal link is the one that let you select from neutral to any other gear you want. Well I don't know how we could miss this since the link is only few cm behind the exhaust mainfold! Although this will be solved by installing some heat sheath aluminised sleeving around the links.

I don't know about the new yaris mounts but I am sure that the old yaris needs an upgraded rear mount because at that power and above 5000rpm the engine really make large moves to the rear. Make sure you consider this before swapping engines... although that is just a tip!

Next installation will mainly consider in heat managment and insulation like:

- Heat screen
- Exhaust Wrap
- Locking metal ties

All branded DEI. I am still not decided on an oil cooler yet! so if anyone has any tips please post :) BTW motor turned out of running 16psi @ 250whp still not 100% :)
this is really a job nicely done, its going to be a legend!

regarding your question about oil cooler, i'm currently using an engine oil cooler from ASR. (http://www.asr-development.com/prod/...port/index.htm)

it comes with an oil cooler adapter with a built-in thermostat.

Picture not included in this copy

Picture not included in this copy

by the way, how about considering ceramic coating on your exhaust manifold, turbine housing and downpipe as well for heat management?

you could also add on a thermal blanket covering the top part of the exhaust manifold to keep the engine bay temperature in check.

just my 2 cents :)
ParmasThread starterML · May 8, 2009#71
Thanks for your info mate! I will gather and ask some about ceramic coating I hope that it isn't that expensive to do at least.

Regarding the oil cooler, it seems quite large to ask you whether you encountered any oil pressure loss? Also I would be interested in seeing better pics at larger size if you have and btw nice setup aswell!

What dimensions of oil cooler do you recommend for my setup?
changchewsoonMalaysia · May 8, 2009#72
hi parmas, ceramic coating shouldn't be too expensive. i did mine for about USD 230 in your currency. i had the exhaust manifold, turbo housing and down pipe coated.

as for the oil cooler im using, its 15 rows and the length should be 225mm if i am not mistaken. have not encountered any loss in pressure so far.

i could send you the high resolution images of the snapshots i have for sharing if you could provide me with your email account.

this setup is quite sufficient for my normal day to day driving and some occasional spirited driving on the street. my engine oil temperature during my normal daily driving is kept around 78'C - 86'C and during long duration high revs it goes up to 92'C - 93'C but it cools down quite fast once you slow down.

i guess the choice of engine oil that you use has a lot to do with it as well. im currently using Motul 300v 5W40.

but if you're planning to build a track car, perhaps you might want to consider a even larger size cooler, and locate it in a place where you have maximum air flow by perhaps utilizing an air duct to direct air to its surface.
ParmasThread starterML · May 10, 2009#73
I was thinking about this oil cooler branded Flex-a-lite and includes a dual circuit and a remote fan triggered within a certain temprature threshold.

http://www.flex-a-lite.com/auto/html/remote-mount.html

Oil cooler 45901

1 attachment not included in this copy

cali yarisCanoga Park, CA · May 10, 2009#74
that's pretty fancy! -- is your oil too hot?
ParmasThread starterML · May 10, 2009#75
Originally Posted by cali yaris ↑
that's pretty fancy! -- is your oil too hot?
At least I am preventing it to be hot but as I said I am in doubt whether it will affect oil pressure.
cali yarisCanoga Park, CA · May 10, 2009#76
Unless there is a leak, your oil pressure should be exactly the same.
TamagoOff Grid · May 10, 2009#77
Originally Posted by cali yaris ↑
Unless there is a leak, your oil pressure should be exactly the same.
it depends on what part of the circuit he taps into for the cooler.
ParmasThread starterML · May 10, 2009#78
Originally Posted by Tamago ↑
it depends on what part of the circuit he taps into for the cooler.
My intension of a using dual circuit oil cooler is that of using half of it after the oil pan and the other half for the transimssion.
TamagoOff Grid · May 10, 2009#79
you're going to cool the transmission gear oil? why?
changchewsoonMalaysia · May 11, 2009#80
i think flex-a-lite is a very good brand as well, its a good choice parmas.

since it comes with a fan controller, you could skip installing an external controller like what i did. am using a pivot super temp here.

just curious, wouldn't you rather have a dedicated cooler for each engine oil and transmission?
ParmasThread starterML · May 11, 2009#81
Originally Posted by changchewsoon ↑

just curious, wouldn't you rather have a dedicated cooler for each engine oil and transmission?
You are probably right in saying this but you have to consider the limited space I have in here. I think this oil cooler with it's active cooling is capable of keeping temps as low as possible I can get. Also it would be rather more expensive to get 2 independent oil coolers than a dual circuit one.

Re: ceramic coating... I done some research and there are many that say is a good asset to own heat management. Here is quite difficult to find someone to do the job for you and I don't wish to risk sending all the parts abroad and never come back! Although I really wish this coating I will keep you updated if I could find one somewhere...
TamagoOff Grid · May 11, 2009#82
so how are you going to pump the transmission gear oil through the cooler?

and "keeping the oil as cool as possible" is not smart. oils are designed to operate in a specific temperature range for them to be efficient. over-cool your transmission gear oil (not sure how you're going to pump it) and you'll end up with oil that just doesn't laugh, as you are heat cycling the oil constantly. leave the transmission alone, focus on the engine oil. if you want to keep oil pressures constant, i suggest cooling the oil coming OUT of the turbo (provided there is NO backpressure through the cooler).
changchewsoonMalaysia · May 11, 2009#83
just to clarify, we're talking about manual transmission here and not automatic right?
ParmasThread starterML · May 12, 2009#84
Originally Posted by Tamago ↑
so how are you going to pump the transmission gear oil through the cooler?

and "keeping the oil as cool as possible" is not smart. oils are designed to operate in a specific temperature range for them to be efficient. over-cool your transmission gear oil (not sure how you're going to pump it) and you'll end up with oil that just doesn't laugh, as you are heat cycling the oil constantly. leave the transmission alone, focus on the engine oil. if you want to keep oil pressures constant, i suggest cooling the oil coming OUT of the turbo (provided there is NO backpressure through the cooler).
The choice of cooling the transmission is scrapped since the C160 can withstand high power and it is complicated to do aswell. Probably the oil cooler will be connected between the oil pan and the turbo.

Still trying to find someone who can do ceramic coating .....
TamagoOff Grid · May 12, 2009#85
Originally Posted by Parmas ↑
Probably the oil cooler will be connected between the oil pan and the turbo.
just be careful to not pressurize the return flow to the oil pan. seriously oversize those lines, as you will blow your turbo seals if there's any backpressure on the oil return line.
ParmasThread starterML · May 12, 2009#86
Originally Posted by Tamago ↑
just be careful to not pressurize the return flow to the oil pan. seriously oversize those lines, as you will blow your turbo seals if there's any backpressure on the oil return line.
What size do you recommend? Would oversize effect oil pressure?
cali yarisCanoga Park, CA · May 12, 2009#87
you will blow your turbo seals if there's any backpressure on the oil return line.
true; done that.
TamagoOff Grid · May 13, 2009#88
Originally Posted by Parmas ↑
What size do you recommend? Would oversize effect oil pressure?
if the cooler is between turbo outlet and oil pan, oversize will not affect oil pressure.

it is highly UNrecommended to restrict oil coming back from the turbo, so if you do this, size it for 3times more than flow out of the turbo.
m911gtChicago · May 13, 2009#89
I hate to add a pointless post to this great thread, but I need to subscribe.

Congrats on the progress Parmas and best of luck with the rest of it.
cali yarisCanoga Park, CA · May 13, 2009#90
I want to see this car on the road soon. Please. 😉
ParmasThread starterML · May 13, 2009#91
Originally Posted by cali yaris ↑
I want to see this car on the road soon. Please. 😉
Well today I tempted myself to take a drive. Got into the car and turned ignition on...

In the meantime some ppl were taking a walk just few metres away when suddenly they heard the loudy exhaust and stopped to figure out from where is this coming. Throttle up and a vitz just appeared humbling.
I was amazed for all ppl who stopped just for few seconds from their usual lifetime staring at the car backfiring on a stop sign.

The drive took only 15min and I can say they were the best minutes of my life! I really wish that there was someone available for video shooting the experience ...
changchewsoonMalaysia · May 14, 2009#92
damn, just by reading your post im already wet~~~ :D :D
ParmasThread starterML · May 14, 2009#93
Ok here is what remains for the setup to be finalized:

- Oil cooler :- Flexalite Thermostat active oil cooler 10 1/2" x 15" x 4" (1/2" Female NPT)

- Completition of Exhaust piping :- 2.5" stainless piping and Y shaped dual mufflers

- Aluminium Intake mainfold

- Ford Cosworth RS5 standard pressure regulator

- Upgraded Fuel Rail

- Ceramic coating on exhaust mainfold / turbo housing / downpipe

- Maybe upgrade valve and springs?

- Tial External wastegate ?

Hope I will get the money for all this within the next 2 months to finish!

BTW do any of you know a company in Europe that sells flexalite oil coolers?
ParmasThread starterML · May 14, 2009#94
Today I found one person who could make ceramic coating for me. He said that the burner reaches 1000 Degrees Celcius for sure. I went to the stainless crafter and gave me a trial piping to test. Tomorrow will go and handle the metal and will see if this can be done! *I hope it works*

What do you recommend in coating apart Exhaust mainfold / Turbo / Downpipe... (Top cover?
CASTREXCosta Rica · May 14, 2009#95
All you need to coat is the turbo, manifold and downpipe... that's where the heat will be coming from.
turboecho2005Ottawa, Ontario · May 17, 2009#96
I can't wait to see it 100% complete and tuned with my old motor.. and 300+hp ;)
changchewsoonMalaysia · May 20, 2009#97
hi parmas,

are you planning to recirculate your BOV back in to your air intake since you are retaining your MAF sensor?

im actually currently thinking of doing so, everytime the the BOV opens and vent the air off to atmosphere i noticed the afr from the wideband goes pig rich.
ParmasThread starterML · May 20, 2009#98
Originally Posted by changchewsoon ↑
hi parmas,

are you planning to recirculate your BOV back in to your air intake since you are retaining your MAF sensor?

im actually currently thinking of doing so, everytime the the BOV opens and vent the air off to atmosphere i noticed the afr from the wideband goes pig rich.
I don't think I will recirculate the BOV cause I love that bov sound :) I don't know if it's normal that the blow off can cause the engine rich maybe there is some setting in the ecu that is causing you this.

What ecu are you using? Does the afr signals this during release of pedal at a certain gear or during gear change?
changchewsoonMalaysia · May 21, 2009#99
hi parmas, im currently driving an automatic and not a manual gearbox.

well, if you're retaining the MAF sensor like me then recirculating is the way to go. reason is the MAF has already measured the air that has passed through and signals the ECU to send fuel, when you close your throttle and your BOV vents the air out to atmosphere the MAF has no idea about it and hence you'll run rich.

and when you're in close loop the O2 sensor picks up a rich reading, it will signal the ECU to reduce fuel and also updates the fuel trim table as well. we don't want that in the long run.

im currently using the e-manage blue wired up with a MAP sensor. the e-manage will clamp the MAF voltage when boost comes in and will rely on the MAP sensor for readings to adjust fuel and to prevent the CEL from coming on.

however, from my wideband reading it shows that during low/partial throttle when the BOV vents I go rich. doing a recirculation and plumbing the air back to the intake after the MAF will help lot in the throttle response and increase the build up of turbo spooling.

i like the sound of the bov as well, even with circulation its actually quite loud especially if you're running a CAI setup. i actually prefer to run as quiet as possible, the sound doesn't mean a lot to me. i prefer to run faster ahead of the guy in traffic light without creating a lot of attention with the BOV.

venting to atmosphere is not suitable for MAF equipped cars unless you're running a MAP setup. alternatively, you could buy a MAF translator like one from HKS and you can remove the MAF all together. The E-Manage Ultimate does it as well, HKS F-CON VPro too.
ParmasThread starterML · May 21, 2009#100
I do not know if recirculating will improve power since the air blown off by the bov is the uneeded air into the turbo piping. Also at that moment in time the engine is at closed throttle and recirculating the air maybe the same as forcing air into the engine when infact it doesn't need it now.

Taking this point now, why and what is the intention of having a bov when infact you want boost air to remain "ready" into the piping? Might aswell not having a bov at all and leave the boosted air into the piping. Well the reasons I guess are that you might blow a hose or force the air into the engine before infact it is needed.

Please correct me if there is something you disagree...