Yarisworld Archive

"Parmas" Motor

490 posts · 124,989 views · page 9 of 10

Replies continued

ParmasThread starterML · Jan 22, 2011#401
Intake setup was finished today. The engine started and ran without even needing a tune.

Also re-routed water lines and intercooler piping (which I need to re-spray though).

The only issue I have is that because of the larger throttle body the idle is at a still on 2000 rpm which is much. The TPS and Idle control connectors match perfectly but I cannot get the idle control work in order to slow idle as I need.

The throttle body is of the 2ZZGE used on Celicas and Vibe GT series cars. I would need the car owners manual to check what is the exact frequency of the idle control motor.

Also made a stainless custom catch can but still needs to setup the fittings.

Next up is the NST crank pulley and we are done!

2 attachments not included in this copy

cali yarisCanoga Park, CA · Jan 22, 2011#402
👏

so nice
YodaFL · Jan 22, 2011#403
sweet. its been a long time coming and you are so close. Happy for you man
CtrlAltDefeatIndianapolis IN · Jan 25, 2011#404
zexy!
pimp my yarischicago · Jan 25, 2011#405
That is one tight engine compartment. All Business! It will make any car owner thinking of running against you, think twice.🎉
ParmasThread starterML · Jan 25, 2011#406
Originally Posted by pimp my yaris ↑
That is one tight engine compartment. All Business! It will make any car owner thinking of running against you, think twice.🎉
Yes it is tight and pretty annoying working on it since you have to remove several pieces to reach some things but I am happy with that as long as it works 😁

Update .. working on a 3 gauge setup of oil pressure/ temp / water temp. Still need to arrange wiring and will post a picture of them as soon as I have time.
xbgodFlorida · Jan 25, 2011#407
Lookin good dude. Thank god your turbo'd, cause I don't think that intake manifod will work right on a N/A cars. Not quite sure it's mathamaticly correct by designe. My buddy Chris at Weapon-R went through two designes before it made power instead of loosing it. Looks good though dude. Enjoy the fruits of your labor.

XBG
cali yarisCanoga Park, CA · Jan 25, 2011#408
^ it's good for a turbo app, looks pretty much like mine. He'll make power in the higher end with it and probably lose some torque in exchange.

Longer runners will make more torque, but you gotta do the math, as xbg said.
xbgodFlorida · Jan 25, 2011#409
I do like the color combo. Haven't seen that combo done.

XBG
ParmasThread starterML · Jan 26, 2011#410
Originally Posted by cali yaris ↑
^ it's good for a turbo app, looks pretty much like mine. He'll make power in the higher end with it and probably lose some torque in exchange.

Longer runners will make more torque, but you gotta do the math, as xbg said.
I didn't try it hard on gears but it seems that for slow running the major difference is throttle response. As soon as I get the gauge setup ready I will continue on my tune...

BTW I found this on ebay/...

I think the problem of the Oil Turbo leak is because I am using a Journal Turbo Fitting instead of Ball Bearing one.

1 attachment not included in this copy

YodaFL · Jan 26, 2011#411
How boost you gonna run?
ParmasThread starterML · Jan 26, 2011#412
Originally Posted by Yoda ↑
How boost you gonna run?
I am trying to tune the engine myself so I am trying to make a nice tune on 9psi only for now and with the Cam timing disconnected so Fully retarded.

After I get the numbers with the 9psi tune, I will activate the VVti and play around again for the best numbers I could achieve.

After that I will leave the VVti on and up the boost 1 psi and tune until I am satisfied with the power end :)
YodaFL · Jan 26, 2011#413
Nice taking your time with it. I gonna try to get mine tuned tomorrow have to call around for the right price
ParmasThread starterML · Feb 19, 2011#414
Here are the latest updates of the engine bay.

- Complete Oil Custom Catch Tank
- Turbo Oil Pressure Gauge
- Added a 3 Gauge Interior Setup

Tuning is almost done. The only thing that remains is tuning on variable camshaft positions

For now I kept low boost (11psi) to verify that the engine holds easily up to 6500rpm. But I am feeling that off boost the engine can improve much more since the camshaft is rather retarded than advanced.

I didn't dyno the engine yet and didn't even try a track time so I cannot post any exact numbers. Also still need to install the much awaited NST crank pulley. The mechs are a bit busy lately so I have to wait for next 2 weekend for another update...

5 attachments not included in this copy

cali yarisCanoga Park, CA · Feb 19, 2011#415
that looks nice.

So you have a separate oil pressure for just the turbo? That looks like a lot of adaptors stacked up! :)
pimp my yarischicago · Feb 20, 2011#416
Love that intake!
Focus_Sh1ftNew Jersey · Feb 21, 2011#417
Looks great man. 👍
Nexus1155Dorchester · Feb 21, 2011#418
That looks like a lot of adaptors stacked up! :)
Everything looks so clean! I'm just wondering if it leaks.
ParmasThread starterML · Feb 24, 2011#419
Originally Posted by Nexus1155 ↑
Everything looks so clean! I'm just wondering if it leaks.
For now it isn't leaking and I am not worrying that it would eventually.

Thanks for the comments 🍻
ParmasThread starterML · Mar 3, 2011#420
The idle problem was solved! Last night I dreamed that the idle motor of the 1NZ is the same like the 2ZZ and well it was infact!!!

The problem was the idle control motor not working for a reason now idles like a charm!

Dyno date is expected to be within about 3 weeks and I hope it will be the final tune! I am eagerly waiting for numbers!
turboecho2005Ottawa, Ontario · Mar 4, 2011#421
Looks great! You've come a long way with this project. Cant wait to see the dyno numbers.
ParmasThread starterML · Mar 8, 2011#422
Yesterday I had my car started and noticed it was running different without changing the base map. Noticed the AFR showing stoich on all loads and rpm.

Done a free-air calibration and it could not get it calibrated. Checked with the manual and it is probably the sensor damaged.

The manual stats that for turbo charged engines the sensor must be mounted 12-16 inch from the turbine outlet. Could it be the issue?

Sensor was only used for 2 months.

What are your experiences?

1 attachment not included in this copy

Bluevitz-rsOshawa, Ontario, Canada · Mar 8, 2011#423
It could be because it's too hot any closer than 12-16 inches. Was the reading changing at all?
YodaFL · Mar 8, 2011#424
What kind of afr gauge you have? You can pull it out and test it.
Focus_Sh1ftNew Jersey · Mar 8, 2011#425
Check continuity maybe?
YodaFL · Mar 8, 2011#426
i kno for my aem you can test it with some carb cleaner and a rag
ParmasThread starterML · Mar 8, 2011#427
The sensor is connected directly to ecu and I can see the values on the Ecu software.

The sensor is Haltech, like the ecu and the reading change slightly from 14-15 on all loads and also when engine is off.
Bluevitz-rsOshawa, Ontario, Canada · Mar 9, 2011#428
If it's still reading 14-15 with the engine off, either your software is clamping the sensor or it's gone bad.
Scubaru Stevecalgary · Mar 10, 2011#429
mine is 4-5 inches from my turbo in my wrx, its worked for 2 years, i believe i need a new sensor now.

as for the sensor reading when the car is off that is normal. the exhaust the piping is that afr, if you leave it on it should slowly slowly dissipate.
free air calibration requires you to remove the sensor from the down pipe in fresh air.

can always try replacing the sensor, i believe most use the 5 or 7 wire bosch. can get them at a decent price mostly.
ParmasThread starterML · Mar 12, 2011#430
Originally Posted by Scubaru Steve ↑
mine is 4-5 inches from my turbo in my wrx, its worked for 2 years, i believe i need a new sensor now.

as for the sensor reading when the car is off that is normal. the exhaust the piping is that afr, if you leave it on it should slowly slowly dissipate.
free air calibration requires you to remove the sensor from the down pipe in fresh air.

can always try replacing the sensor, i believe most use the 5 or 7 wire bosch. can get them at a decent price mostly.
Thanks for the suggestions.

I tried the free air calibration and didn't change at all. Contacted Haltech directly and he needed a log file of the AFR reading vs Sensor voltage. After he send a reply that from the log it seems that the sensor needs replacement!

I hope the next one will at least be good for one year and not 2 months!

In the meantime I am trying to solve the last issues and installations which are:

- Oil leak from the turbo compressor discharge area
- Need new oil gauges as I have issues with them
- Installation of the NST torque damper
- Installation of the NST crank pulley
- And finally off to the dyno and hope will be ok for long time!

The main thing that is making me nervous is the oil leak from the turbo to the discharge/boost piping. I was thinking that the turbo seals were gone but I went to a Garret distrubtor and checked shaft play and seems fine. He said that for turbos it is normal to have a slight oil leak from the discharge area but I am not sure about it after I read this http://www.turbobygarrett.com/turbob...timization.pdf

11 Point Checklist for Turbo Best Performance and Efficiency.

1. Application Information – target horsepower, intended use of vehicle, etc.

- Street / Drag racing. Target Hp 300Hp

2. Air filter sizing - determine size for application needs

- Air filter piping is the same size of the inlet compressor housing

3. Oil Supply - restrictor for ball-bearing turbo

- Ball bearing turbos use 1mm restrictor ( which I have it installed recently )

4. Oil Drain – proper size and routing

- The Drain size seems enough visually but I am not sure how much is the inner diameter. Although I have a suspect in this case.... Since the turbo is behind I can only touch and feel the area and cannot see it with the engine on the car. I am sure I felt a short 90 degree angle fitting exactly after the turbo fitting and it could be there is a bottle neck there. I am trying to re-route the drain to a straight line as possible

5. Water Lines - set up for greatest thermal siphon effect

- Siphone effect means water IN must be connected to lower level than Water Out if (I read well the document in the link). I am using the water lines that were connected to the Idle control motor but I didn't know which is IN or OUT ?

6. Charge Tubing – determine diameter for application needs

- Charge Tubing is 2" which is the same size of the charge outlet of the turbo. I don't see an issue about that.

7. Charge-Air-Cooler - determine core size for application needs, design
manifolds for optimal flow, mount for durability

- Intercooler is a little big but I prefer to have some lag than having high intake temps. Lag should be gone after I increase more boost.

8. BOV – VTA for MAP engines and by-pass for MAF engines

- HKS SSQV BOV seems fine for me

9. Wastegate – connect signal line to compressor outlet, smooth transition to
external wastegate

- Using internal wastegate, no issues with that

10. System Testing – pressurize system to check for leakage, periodically check
clamp tightness and the condition of couplers

- Here is the problem 😠

11. System Monitoring – proper gauges/sensors to monitor engine for optimal
performance and component durability

- A turbo speed gauge. Is it really needed?
Focus_Sh1ftNew Jersey · Mar 12, 2011#431
The location of your oil drain looks fine...

Out of curiosity, what is your cold idle RPMs? I had a lot of blow-by during idle when I had a 1ZZ TB on. cdydjded pointed out that the higher RPM at cold start was causing excessive oil pressure because the polymer strands haven't had enough time to warm up and expand. Hopefully I explained that right. More importantly though, when I put the 1NZ TB back on and effectively lowered the cold idle RPMs, blow-by seemed to have disappeared.
ParmasThread starterML · Mar 12, 2011#432
Originally Posted by Focus_Sh1ft ↑
The location of your oil drain looks fine...

Out of curiosity, what is your cold idle RPMs? I had a lot of blow-by during idle when I had a 1ZZ TB on. cdydjded pointed out that the higher RPM at cold start was causing excessive oil pressure because the polymer strands haven't had enough time to warm up and expand. Hopefully I explained that right. More importantly though, when I put the 1NZ TB back on and effectively lowered the cold idle RPMs, blow-by seemed to have disappeared.
I set cold idle to be above 2000 rpm until it reaches 50C it quits to 1400. I set this high rpm as noticed many factory cars use the same technique to warm the engine quickly to operational point. Mine warms up within a minute or two on idle.

I don't think this is related to the oil leak since when the oil is cold it is thicker than when it's hot so if it leaks at 2000rpm when cold it should also leak when at 1400rpm when hot!

Also I was thinking that maybe the engine needs to breath more through the Top Cover. I was thinking of maybe making bigger inner diameter fittings and a larger breather on the outside. Could it be one of the issues?
ParmasThread starterML · Mar 27, 2011#433
I got the turbo checked by a specialist regarding the compressor oil leak and he said it is fine and there is no play with the shafts and it must be something with the drain.

So I am arranging the drain setup to a straight line and a bigger o/d pipe to try to solve this forever.

In the meantime I done some works while the turbo and manifold are out.

Will post some pics of the drain new setup when it is ready

8 attachments not included in this copy

ilikericesavannah, ga · Mar 27, 2011#434
quick question.. i know the reasoning behind the exhuast wrap, but is it nessissary on the yaris for safty or are you just doing it for added performance?
ParmasThread starterML · Mar 27, 2011#435
Originally Posted by ilikerice ↑
quick question.. i know the reasoning behind the exhuast wrap, but is it nessissary on the yaris for safty or are you just doing it for added performance?
The reason is both.

1. Prevent heat to damage or wear any parts like gear cables, hydraulic tubing and any other thing in its vicinity. (Especially for our small engine bay this is one to take care of) . I already replaced 2 gear cables because of this btw!

2. With the Thermal barrier paint plus the Exhaust wrap I am hoping to obtain lower engine bay temps to at least 10C lower as advertised. Also with the wrapping you are keeping the exhaust gases as hot as possible. The hotter the gases, the better they flow and with all going to the Turbo you might sense a better or earlier spool up.
ParmasThread starterML · Mar 31, 2011#436
Finally installed the NST crank pulley set. No issues yet....

3 attachments not included in this copy

YodaFL · Mar 31, 2011#437
And there won't be.
ParmasThread starterML · Apr 1, 2011#438
Originally Posted by Yoda ↑
And there won't be.
Today I had some time to fix the power steering and alternator belt in place. With the power steering belt had no issues at all.

Although with the Alternator Belt I had issues with it. I have all 3 pulley NST set and the belt matches perfectly the alternator pulley while in the crank pulley it is a little bit tighter. Infact the belt curves through the edges of the crank pulley. Pushing it with my finger with some force it sits ok while on the alternator pulley it sits easy.

Is there anyone having this issue?

Could the belt slip if I try to run it like this?
Bluevitz-rsOshawa, Ontario, Canada · Apr 1, 2011#439
maybe a picture might clear this up better.
pimp my yarischicago · Apr 1, 2011#440
I have my aem wideband in the same location as yours. Did U find out why yours stopped working? Mine is working good. But the stock sensor that was located right next to it is fried. Mabe heat? I dont know. I had to lengthen the wiring on the stock sensor so it would reach. Engine compartment looks sweet!
ParmasThread starterML · Apr 1, 2011#441
To blue vitz - I will take one tomorrow. Probably I have to remove it again and modify the width of the pulley where the belt fits.

As regarding to the sensor, AEM and any brand that make widebands recommend at least 14 inch down from the turbo. So by rule mine is located wrong and I am thinking of doing it the right way they recommend.

To cdydjded - I already have 2 sensors in stock ready to install but thanks!
ParmasThread starterML · Apr 2, 2011#442
I couldn't get a good picture for you to review although I managed to fix the pulley by machining a bit from one side. Now the belts hook fine with no problems
Bluevitz-rsOshawa, Ontario, Canada · Apr 2, 2011#443
👍
ParmasThread starterML · Apr 3, 2011#444
Drain fixed to a straight line with bigger inner tubing. Wrapped the tube with titanium since it is passing through lots of heat there.

Sorry but picture was taken by my mobile..

1 attachment not included in this copy

johnny_vitzHamilton, Canada · Apr 3, 2011#445
Have you put the manifold back on since the wrap went on? It looks like you might have a hell of a time trying to get a couple of the bolts done up🤷
ParmasThread starterML · Apr 4, 2011#446
Originally Posted by johnny_vitz ↑
Have you put the manifold back on since the wrap went on? It looks like you might have a hell of a time trying to get a couple of the bolts done up🤷
Yes infact the middle bolt of the manifold flange needed to be replaced to a shorter one because of the drain going down exactly infront. Took me about 10min to fix that only bolt in due to lack of space.
johnny_vitzHamilton, Canada · Apr 4, 2011#447
Originally Posted by Parmas ↑
Yes infact the middle bolt of the manifold flange needed to be replaced to a shorter one because of the drain going down exactly infront. Took me about 10min to fix that only bolt in due to lack of space.
Oh, ok 😁 Looked a bit tight in there...
Wrap looks good, I just bought some to do my header...eventually.
ParmasThread starterML · Apr 5, 2011#448
Originally Posted by johnny_vitz ↑
Oh, ok 😁 Looked a bit tight in there...
Wrap looks good, I just bought some to do my header...eventually.
I hope you have my patience cause you really need with it. Good luck 👍
ParmasThread starterML · May 24, 2011#449
Yes I'm late posting.... I have been busy with lots of works out on going project and this is finally the last mod since there isn't any other space available now LOL!

Summer special tune.... Idividual Twin Radiator setup. The aftermarket rad is fitted after the turbo line in order to prevent unwanted heat from the turbo affecting engine temperature... I was seeing 90C and over with the fan on. Also I installed another fan on the front which is visible on the picture as an add on!

I also installed the Torque damper with lots of custom work to make it fit and also an exhaust motor that cuts the exhaust from the middle. Next thing up dyno although the engine is pretty quick with only 12psi boost. I am almost sure it is above 220Bhp now .... hope to make it up till 300Bhp at 16psi!

Will post pics and vids on the dyno next up!

2 attachments not included in this copy

rob323Joyner, Brisbane · May 24, 2011#450
Did the extra radiator help? And where are you measuring your water temps?