Yarisworld Archive

2ZR Turbo Yaris

561 posts · 343,257 views · page 5 of 12

Replies continued

06YarisRSThread starterFredericton, New Brunswick, Canada · May 24, 2019#201
Gauges

I am still deciding what I'm going to do for gauges. As mentioned, I can see a host of valuable turbo-related data through Torque Pro (such as boost, AFR, intake temps, timing etc), but in order for me to monitor oil and trans temps, I'll need aftermarket gauges since I haven't been able to confirm if Techstream can provide that live data. I have a couple of fittings that I may use for my possible gauges. The large one splices into my trans cooler return line and the smaller one is an oil drain plug with a 1/8" NPT thread, but because it narrows I'll be restricted in what sensor I use. It looks like I may have to go with Glowshift as they have a narrower sensor probe.

Here are the potential sensor ports.

Picture not included in this copy

And, here is the gauge I'm thinking of for my oil and trans temps.

https://www.ebay.com/itm/GlowShift-1...T/292521363623

Picture not included in this copy


OR

This...

Picture not included in this copy

This...

Picture not included in this copy

And this...

Picture not included in this copy

I didn't get to any additional wiring today, but I did replace a few inches of my trans cooler out line with a 90 degree piece of trans hose that I got from a 2005 Jeep Wrangler. The cooler hose was rubbing on the passenger side intercooler intake coupling. Once I installed the 90, it allowed me to raise the intercooler coupler a bit giving me more clearance between the front rad support sub frame, which was a real bonus. If you look closely, you can see the little rubber elbow down in behind the intercooler intake coupler on the passenger side. Oh, and I sanded and painted my horn. It was quite rusty and ugly.

Picture not included in this copy



I still need to install the injectors and may use that as an excuse tomorrow to avoid tackling the F/IC wiring. I'll try to source a nice large firewall plug - one big enough to handle the F/IC harness, vacuum line and all my gauge wires. Then I'll need to source an appropriately sized hole saw.

I should receive my new 24" oil supply line in a day or two. The one that came with kit is about 40" long - way too long to effectively deal with in this tiny engine bay. Here is the -4AN fitting, capped and awaiting its supply line. The 24" line should be perfect with a nice gradual loop from the top of the turbo to the supply port. If I measured correctly, I won't even need to fasten the line anywhere between the turbo and supply port to prevent contact with anything on the engine or body.

Picture not included in this copy
tmontagueCaledonia Ont. · May 24, 2019#202
Just a heads up on the glowshift gauges - I found them to be +/- 10psi/degrees in accuracy and always had electrical issues with them as they were finicky


I know the price is really tempting but in what it cost in time to try and splice their tiny gauge wires and constantly try and fix electrical issues, I would just recommend going with an AEM series gauge from the get go.

AEM gauges are far from the most expensive and they aren't the most cheapest but their harness is all plug and play with easy to remove connectors, all you have to do is splice in a ground and ignition sources power. I have found them to be +/-2 psi/degrees and have zero electrical issues since my install.

Just something to keep in mind but glowshift definitely showed their price
06YarisRSThread starterFredericton, New Brunswick, Canada · May 24, 2019#203
Originally Posted by tmontague ↑
Just a heads up on the glowshift gauges - I found them to be +/- 10psi/degrees in accuracy and always had electrical issues with them as they were finicky


I know the price is really tempting but in what it cost in time to try and splice their tiny gauge wires and constantly try and fix electrical issues, I would just recommend going with an AEM series gauge from the get go.

AEM gauges are far from the most expensive and they aren't the most cheapest but their harness is all plug and play with easy to remove connectors, all you have to do is splice in a ground and ignition sources power. I have found them to be +/-2 psi/degrees and have zero electrical issues since my install.

Just something to keep in mind but glowshift definitely showed their price
Thanks indeed for the input. You are right, the price is attractive, but if they are buggy, then they probably aren't what I'm looking for. That said, I just had a look and I'd be looking at $600.00+ for the few gauges I'd need. Can't see getting that past the finance committee after the $$$ I've spent already lol. I really wish that Torque could access the data I'm looking for from the ECU. I can see virtually everything in my Kia van.

Other than the inaccuracy, can you tell me a bit about the electrical problems? Is it largely bad connectors/hardware/wiring? I ran a bunch of those cheapy Chinese gauges in my old Dodge van and and the temp ones worked fine and lasted a long time - I sold the van and they were still working after a couple of years. The oil pressure ones would work for a few months and then the sender would ultimately fail. The accuracy on the temp gauges wasn't great either, but I did test them in a pot of boiling water with a digital thermometer and they were in the order of +/- 5 degrees off. I could live with that, but the again, they were like $18.00 - $20.00 each. If the Glowshift gauges are that bad, then I wouldn't be up for paying what is 3 - 4 times the price for about the same quality of product.

More thought... I'm going to be running full synthetic oil, so do I really need to know oil temps? I know that oil doesn't hang in the same temp range as water, but is it likely to get way, way above water temps? Like, in the order of 50+F degrees? With regard to oil pressure, one guy said all a gauge will do is let you watch the destruction of your turbo in realtime as by the time you lose pressure, the turbo is toast. He said that oil temp would be more valuable as it is a variable that you could control - aka, cooler. I will already have AFR, boost, water temp, intake temp etc through Torque. If I did decide to go with better gauges and had to buy them over time, which would you recommend going with first?

Thanks again,
tmontagueCaledonia Ont. · May 25, 2019#204
Originally Posted by 06YarisRS ↑
Thanks indeed for the input. You are right, the price is attractive, but if they are buggy, then they probably aren't what I'm looking for. That said, I just had a look and I'd be looking at $600.00+ for the few gauges I'd need. Can't see getting that past the finance committee after the $$$ I've spent already lol. I really wish that Torque could access the data I'm looking for from the ECU. I can see virtually everything in my Kia van.

Other than the inaccuracy, can you tell me a bit about the electrical problems? Is it largely bad connectors/hardware/wiring? I ran a bunch of those cheapy Chinese gauges in my old Dodge van and and the temp ones worked fine and lasted a long time - I sold the van and they were still working after a couple of years. The oil pressure ones would work for a few months and then the sender would ultimately fail. The accuracy on the temp gauges wasn't great either, but I did test them in a pot of boiling water with a digital thermometer and they were in the order of +/- 5 degrees off. I could live with that, but the again, they were like $18.00 - $20.00 each. If the Glowshift gauges are that bad, then I wouldn't be up for paying what is 3 - 4 times the price for about the same quality of product.

More thought... I'm going to be running full synthetic oil, so do I really need to know oil temps? I know that oil doesn't hang in the same temp range as water, but is it likely to get way, way above water temps? Like, in the order of 50+F degrees? With regard to oil pressure, one guy said all a gauge will do is let you watch the destruction of your turbo in realtime as by the time you lose pressure, the turbo is toast. He said that oil temp would be more valuable as it is a variable that you could control - aka, cooler. I will already have AFR, boost, water temp, intake temp etc through Torque. If I did decide to go with better gauges and had to buy them over time, which would you recommend going with first?

Thanks again,
I definitely understand the situation regarding finances, it was one of the reasons I went with Glowshift in the first place. In hindsight waiting a few month to purchase AEM gauges would have been the best bet in my situation.

So the main issues with the GS gauges was the extremely small gauge wiring they come with. You have to run your own wires from the sender/sensor to the super tiny wires behind the gauge. You cannot find wires or connectors that small from typical go to stores. I had to double back the small gauge wire to make it crimpable. The gauge needle would randomly start to move 40psi lower or higher at random times. Then sometimes if I tapped the gauge it would do it again. I figured it must be a loose crimp so I rewired and triple checked all my connections to no avail as the issue persisted.

Instead of only having to connect a ground and a hot, you have 3 extra wires that although optional, they run the auto dimming feature and they keep the memory for what color you last chose. These always never held the color properly and would typically default to blue on 2 of the 3 gauges I had. Think of how messy the wiring was, 5 wires behind every gauge each with their own connectors, it was a mess.

AEM conveniently supplies a wire loom with proper connectors to attach the sensor to the back of the gauge. This makes them easy to disconnect when ever you need to or if you need to replace a sensor. All you have to do is splice in a hot and a ground on 2 of the wires from the loom. I have to extend a few wires to make it reach where I wanted the gauges to go, but the wire gauge is not super small so it was easy to work with and IIRC it matched the smallest gauge you can find at CT (21gauge I think?) AEM gauges have an auto sensor that dims the back light based on ambient light in the car. Much simple, cleaner and no gauge sweeping issues or weird electrical problems. Oh, and GS gauges have a little plastic button to change the back light color. Thus button is very loose and rattles consistently since day 1. All of the gauges were like that, it wasn't a one off.

Truth is a proper full syn oil can easily handle upwards of 300*F, most engineers will tell you 450-500F is its limit. Based on my 13k km UOA of 5w30 Pennzoil UP that regularily saw 295F it never degraded the oil to where it lost it's lubricity or viscocity. The whole belief that 260F is an oils upper limit and anything after that needs a cooler is outdated and obsolete with modern full syn oils.

Where temp matter is when it reduces yourt operating pressure below spec. For the 2zr according to Toyota it is 22-58 psi at 3k rpm and anything greater than 3 psi at idle.


Now to fix that you can either run a cooler or simply up a viscocity to maintain pressure, but then you would be running too high a viscocity when not on track. This is why a cooler is ideal for a car that is track driven and a DD'er only if the track pushes it out of its oil pressure specs. I actually strongly disagree with the guy that told you oil temp is more valuable than pressure and here is why:

If your engine has catastrophic failure and you loose oil at an alarming rate, neither a temp or pressure gauge will help you - well maybe a pressure gauge would, but you would have to have it set to an alarm or constantly be monitoring it every couple seconds. Oil temp only tells you the temp of the oil, not what actually matters. You will absolutely never get the oil too hot for a full syn's capability, even if you tracked the crap out of your car. You potentially could push the car/oil outside of the pressure specs if you tracked the crap of of your car.

Notice in the above, the dependant variable is pressure and it is dependant on temp. But only knowing the temp tells you nothing of the pressure. But by knowing pressure you know what is important regardless of the temp. Pressure if a product of temp. If you are going to get 1 gauge, let it be oil pressure. This will guide you in what oil viscosity you need to run (spoiler alert, I can almost guarantee you that 0w20 will be perfectly fine)

Here is why I doubt you will have an oil temp issue. Oil typically runs equal to, or 10 degrees F above coolant temp in 75F temps. Add 10F in peak summer months and subtract 10F in colder months. This is in city driving for a long time or highway cruising, even at 130 km/h. Where oil temps will slightly go up under these conditions is when you climb a long skyway bridge - or better put, any increase engine load. This is why 10 mins in to a 40 min lapping session at the track, my oil temps started to climb. Coolant would peak at 230F and oil would creep up to 285F and hand out there for the rest of the session (this was on stock cooling)

This was only seen during WOT and constantly at high rpm's. To put it in perspective I would go through 3/4 of a tank of gas during my 60km trip to the track and my 120km on the track.

You will never come close to these constant engine loads or temps on the street without getting arrested first. Even with an oil cooled turbo you still won't come close to those temps. The engine has no where near the load or demand on it. Spirited driving is still much more tame and less demanding than full out track driving.

In all honesty you could save your cash and forgo the gauges completely. It gives you info, but info you likely do not need other than for curiosity's sake. You already took care of the trans temp issue with a cooler so I can't see you having issues there. If you are worried about that than run a Redline ATF instead of the Toyota WS fluid which doesn't appear to be that robust of a fluid unlike their 0w20 oil.

Don't spec a higher weight oil unless you see pressures outside of the Toyota spec'd limits. Lower viscosity means higher flow which means more cooling. Higher viscosities increase temps. This is well documented on the gt-86 platform when people go from 0w20 to 5w30. It also likely contributed to my oil temps last track season as well.

This is my two cents based on me DDing in various temps and pushing my 2zr well past it's limit while keeping a careful eye on oil temps and pressure. I was surprised by some of the date I gathered, it wasn't what I was told or assumed.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 25, 2019#205
Originally Posted by tmontague ↑
I definitely understand the situation regarding finances, it was one of the reasons I went with Glowshift in the first place. In hindsight waiting a few month to purchase AEM gauges would have been the best bet in my situation.

So the main issues with the GS gauges was the extremely small gauge wiring they come with. You have to run your own wires from the sender/sensor to the super tiny wires behind the gauge. You cannot find wires or connectors that small from typical go to stores. I had to double back the small gauge wire to make it crimpable. The gauge needle would randomly start to move 40psi lower or higher at random times. Then sometimes if I tapped the gauge it would do it again. I figured it must be a loose crimp so I rewired and triple checked all my connections to no avail as the issue persisted.

Instead of only having to connect a ground and a hot, you have 3 extra wires that although optional, they run the auto dimming feature and they keep the memory for what color you last chose. These always never held the color properly and would typically default to blue on 2 of the 3 gauges I had. Think of how messy the wiring was, 5 wires behind every gauge each with their own connectors, it was a mess.

AEM conveniently supplies a wire loom with proper connectors to attach the sensor to the back of the gauge. This makes them easy to disconnect when ever you need to or if you need to replace a sensor. All you have to do is splice in a hot and a ground on 2 of the wires from the loom. I have to extend a few wires to make it reach where I wanted the gauges to go, but the wire gauge is not super small so it was easy to work with and IIRC it matched the smallest gauge you can find at CT (21gauge I think?) AEM gauges have an auto sensor that dims the back light based on ambient light in the car. Much simple, cleaner and no gauge sweeping issues or weird electrical problems. Oh, and GS gauges have a little plastic button to change the back light color. Thus button is very loose and rattles consistently since day 1. All of the gauges were like that, it wasn't a one off.

Truth is a proper full syn oil can easily handle upwards of 300*F, most engineers will tell you 450-500F is its limit. Based on my 13k km UOA of 5w30 Pennzoil UP that regularily saw 295F it never degraded the oil to where it lost it's lubricity or viscocity. The whole belief that 260F is an oils upper limit and anything after that needs a cooler is outdated and obsolete with modern full syn oils.

Where temp matter is when it reduces yourt operating pressure below spec. For the 2zr according to Toyota it is 22-58 psi at 3k rpm and anything greater than 3 psi at idle.


Now to fix that you can either run a cooler or simply up a viscocity to maintain pressure, but then you would be running too high a viscocity when not on track. This is why a cooler is ideal for a car that is track driven and a DD'er only if the track pushes it out of its oil pressure specs. I actually strongly disagree with the guy that told you oil temp is more valuable than pressure and here is why:

If your engine has catastrophic failure and you loose oil at an alarming rate, neither a temp or pressure gauge will help you - well maybe a pressure gauge would, but you would have to have it set to an alarm or constantly be monitoring it every couple seconds. Oil temp only tells you the temp of the oil, not what actually matters. You will absolutely never get the oil too hot for a full syn's capability, even if you tracked the crap out of your car. You potentially could push the car/oil outside of the pressure specs if you tracked the crap of of your car.

Notice in the above, the dependant variable is pressure and it is dependant on temp. But only knowing the temp tells you nothing of the pressure. But by knowing pressure you know what is important regardless of the temp. Pressure if a product of temp. If you are going to get 1 gauge, let it be oil pressure. This will guide you in what oil viscosity you need to run (spoiler alert, I can almost guarantee you that 0w20 will be perfectly fine)

Here is why I doubt you will have an oil temp issue. Oil typically runs equal to, or 10 degrees F above coolant temp in 75F temps. Add 10F in peak summer months and subtract 10F in colder months. This is in city driving for a long time or highway cruising, even at 130 km/h. Where oil temps will slightly go up under these conditions is when you climb a long skyway bridge - or better put, any increase engine load. This is why 10 mins in to a 40 min lapping session at the track, my oil temps started to climb. Coolant would peak at 230F and oil would creep up to 285F and hand out there for the rest of the session (this was on stock cooling)

This was only seen during WOT and constantly at high rpm's. To put it in perspective I would go through 3/4 of a tank of gas during my 60km trip to the track and my 120km on the track.

You will never come close to these constant engine loads or temps on the street without getting arrested first. Even with an oil cooled turbo you still won't come close to those temps. The engine has no where near the load or demand on it. Spirited driving is still much more tame and less demanding than full out track driving.

In all honesty you could save your cash and forgo the gauges completely. It gives you info, but info you likely do not need other than for curiosity's sake. You already took care of the trans temp issue with a cooler so I can't see you having issues there. If you are worried about that than run a Redline ATF instead of the Toyota WS fluid which doesn't appear to be that robust of a fluid unlike their 0w20 oil.

Don't spec a higher weight oil unless you see pressures outside of the Toyota spec'd limits. Lower viscosity means higher flow which means more cooling. Higher viscosities increase temps. This is well documented on the gt-86 platform when people go from 0w20 to 5w30. It also likely contributed to my oil temps last track season as well.

This is my two cents based on me DDing in various temps and pushing my 2zr well past it's limit while keeping a careful eye on oil temps and pressure. I was surprised by some of the date I gathered, it wasn't what I was told or assumed.
Wow! Thanks for the detailed response, Trevor. Lots of great info here. I clearly have a few options:

1) Trans Temp Gauge, No Oil Temp Gauge, No Oil Pressure Gauge: Do an oil pressure test with a pressure gauge at the oil port and flow rate at the turbo oil feed (I have the specs required for that). If specs are good, button everything up and not worry about it again. Install the trans temp gauge and call it done. I have the fittings and it would be a simple install.

2) Trans Temp Gauge and Oil Temp Gauge: Install the trans temp gauge as above and if I go with a oil temp gauge using the bored drain plug, I'd have to go with Glowshift as they are the only ones I can see with a sensor probe narrow enough to work in the oil plug fitting that I got. The dual Glowshift gauge I posted the pic of first has full harnesses, so might be marginally better than the individual gauges from a wiring reliability standpoint. Of course, I'd run their harnesses through split loom and secure that along the way with zipties.

3) Trans Temp Gauge, Oil Temp Gauge and Oil Pressure Gauge: For the oil pressure gauge, I'd need an "X" type fitting at the oil pressure port on the engine to accommodate the oil pressure sending unit.

4) Trans Temp and Oil Pressure: as described above.

5) No gauges at all

I'm am leaning toward Option 4.

I'm really not getting the warm and fuzzies about using the oil drain plug fitting with the 3/8" female bore. If for any reason that broke off, the results could obviously be catastrophic. Because of the oil drain plug angle (pointing downward at about a 45 degree angle), it would put the sensor in a strike path if I did run over anything.

If I drop my oil pan and tap a 1/8" NPT hole, I would not be limited to the Glowshift gauges and the options would be wide open.

Decisions, decisions... 😁
tmontagueCaledonia Ont. · May 25, 2019#207
She runs!!!!
06YarisRSThread starterFredericton, New Brunswick, Canada · May 25, 2019#208
Originally Posted by tmontague ↑
She runs!!!!
She does! I am concerned a bit about the fuel trims. The STFT and LTFT are around +18 to +19. I'm hoping that it's not related to the fact that I'm using a vented valve cover filter and it's resulting in a vacuum leak, as I believe you alluded to. But, this is what I was advised to do. The other thing is that I don't know if the downstream o2 sensor has any bearing on fuel trims as it's completely disconnected. The odd thing is is that no codes have been set and the car has run 5 - 6 times for a total of about 1/2 hour. Also not sure how the F/IC will affect these readings. As happy as I was that the car started right up - literally on the first crank - I was hoping that when it ran, it would run the same as before the kit. The engine is extremely smooth and may be idling a couple hundred RPM above normal - around 750 RPM. I will go back and check all my other vacuum hoses.

I did rev it up to about 3500 RPM - only after about a total of 20 minutes of idling - and the turbo spooling kinda freaked me out a bit. It's quite a high pitched squealing sound, though I did have my intake off for this initial testing. I paniced a wee bit as it sounded a little like metal on metal, but after watching a few youtube vids on turbo sounds, it's quite similar. Plus, I'm getting great oil flow through the turbo.

It did take a bit to prime the cooling system after some coolant loss from having the heater hoses, throttle body coolant lines etc off. I appear to be getting decent coolant flow through the turbo as the cooling hoses are getting warm. The only thing is is that the upper heater hose isn't really getting that warm, but the lower one is. And, my heater isn't putting out as much heat as before. It is warm but not hot. There may still be some air in the system. Also, the turbo cooling lines are considerably smaller than the actual heater hoses, so there may be some restriction of volume happening there.

Trevor, could you do me a big favor at some point? If you get a chance and are willing, next time you run your car, could you compare the temps of the upper and lower heater hoses and see if they are similar as your car reaches operating temp? Maybe let me know how long it takes for those two hoses to reach a similar temp? I haven't really run mine at temp for very long, so maybe the upper hose (return to engine line, I presume) needs longer to heat up. I tapped into the hose that comes out of the driver's side of the block. The return line, I believe enters the rear of the block. I don't think it actually matters which hose is tapped into.
MaritimeWoodstock nb · May 26, 2019#210
Nice!

Sent from my moto e5 play using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · May 26, 2019#211
Thanks gents! Just a few little bugs to work out. I have a tiny leak at the turbo drain fitting - basically a little drip forms on one for the bolts after running for a bit. I need to source a better gasket. Fuel trims are running high, but the F/IC hasn't been connected yet and it has an internal MAP sensor, so maybe that fixes the trims. Don't yet know much about MAF vs MAP. Also, it could be my valve cover vented to atmosphere causing a vacuum leak. I've got a ticket into turbokits.com for advice on this one. Finally, my heater isn't as hot as it used to be. I did have to fill up with coolant again after disconnecting several hoses, so maybe I've got a bubble in there that needs to work its way out. Also, the turbo cooling lines reduce down in size a lot so maybe it's just less flow through that system.

Overall, great so far. I'm sure the "real fun" will start once I get the F/IC hooked up. Wish me luck. I'll likely need it!
tmontagueCaledonia Ont. · May 27, 2019#212
I would be very surprised if the vented valve cover has anything to do with your fuel trim issue as long as you have no open bungs on your intake or manifold down strem of the maf sensor. My concern with the vented valve cover was crankcase pressure issues as it normally has a vacuum on it pulling out the vapors. That said it shouldn't be a problem because any built up pressure will be greater than atmospheric pressures and vent out anyways.

The F/IC should be able to correct the fuel trims, but other than a vacuum leak I'm not sure why you are running lean fuel trims. FWIW ever since I went with an aftermarket full header back exhaust I have always run -12 to -14 LTFT. This was with my 1nz as well as the 2zr.

Check your oil catch can for vacuum leaks, happens a lot more than you would think and it was the source of a vacuum leak on my 1nz. Do your FT's change/normalize when you rev it to 3k rpm and hold it there? that is a good test of a vacuum leak as there is less vacuum on the system as the throttle opens.

I'll check my heater hoses tonight but the coolant should bleed itself out if that is infact the issue. Also it helps to have the front of the car jacked higher than the rear to aid in bleeding. It puts the rad cap at an even higher point than any other cooling system component to aid in air removal. Also coolant temps will rarely get up to full operating temp idling in a driveway so the heater core will still act as a heat sink even without the hvac fan running and it will still somewhat cool the coolant.

The downstream O2 sensor is a dumb sensor and shouldn't play a role in FT's unlike the upstream AFR sensor does. The downstream O2 sensor typically should throw a code P0420 etc when it is disconnected. But in my experience I have found this to be one of the last engine readiness checks that the ECU runs through so it may take some various condition driving for it to trigger on.

Good luck with the wiring!
06YarisRSThread starterFredericton, New Brunswick, Canada · May 27, 2019#213
Originally Posted by tmontague ↑
I would be very surprised if the vented valve cover has anything to do with your fuel trim issue as long as you have no open bungs on your intake or manifold down strem of the maf sensor. My concern with the vented valve cover was crankcase pressure issues as it normally has a vacuum on it pulling out the vapors. That said it shouldn't be a problem because any built up pressure will be greater than atmospheric pressures and vent out anyways.

The F/IC should be able to correct the fuel trims, but other than a vacuum leak I'm not sure why you are running lean fuel trims. FWIW ever since I went with an aftermarket full header back exhaust I have always run -12 to -14 LTFT. This was with my 1nz as well as the 2zr.

Check your oil catch can for vacuum leaks, happens a lot more than you would think and it was the source of a vacuum leak on my 1nz. Do your FT's change/normalize when you rev it to 3k rpm and hold it there? that is a good test of a vacuum leak as there is less vacuum on the system as the throttle opens.

I'll check my heater hoses tonight but the coolant should bleed itself out if that is infact the issue. Also it helps to have the front of the car jacked higher than the rear to aid in bleeding. It puts the rad cap at an even higher point than any other cooling system component to aid in air removal. Also coolant temps will rarely get up to full operating temp idling in a driveway so the heater core will still act as a heat sink even without the hvac fan running and it will still somewhat cool the coolant.

The downstream O2 sensor is a dumb sensor and shouldn't play a role in FT's unlike the upstream AFR sensor does. The downstream O2 sensor typically should throw a code P0420 etc when it is disconnected. But in my experience I have found this to be one of the last engine readiness checks that the ECU runs through so it may take some various condition driving for it to trigger on.

Good luck with the wiring!
Great info as always, Trevor. Thanks. I will check my catch can for leaks. I'll also see how the trims react at higher rpm, around the suggested 3000. Thanks for being willing to check your heater hoses. I did run the car a bit today and the upper hose seemed warmer than yesterday.

I do have to lengthen my o2 sensor wires and then decide how I am going to route it to the opposite side of the downpipe. I haven't decided, though, whether or not I should have a cat installed. What will however be a logistical problem is how to get the car to the exhaust shop with basically a straight pipe. It is extremely loud! So much so, that I have to wear ear plugs when running the car even at idle. I was wondering if I ought to get a temporary cylindrical muffler that would clamp to the 3" downpipe, so that I could get to the exhaust shop without deafening myself or getting pulled over.
ern-dizCA all day · May 28, 2019#214
So impressive. Massive congrats on the first start. Sounds like you'll have the bugs worked out in no time. Beyond cool.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 28, 2019#215
Originally Posted by ern-diz ↑
So impressive. Massive congrats on the first start. Sounds like you'll have the bugs worked out in no time. Beyond cool.
Thanks ern-diz! I think, from a technical standpoint, the most challenging part remains - hooking up the F/IC. To be honest, I've done my best to figure out the wiring, but I'm not fully confident in my ability to have done that correctly. Let's just say I had to make some guesses based upon info from a variety of sources. No one has, as of yet, confirmed decisively that my wiring is correct. The guys at AEM said my diagrams look right, but they couldn't be sure as they were unfamiliar with the car's ECU. I may pester them again for more definite answers, but since the F/IC has been discontinued - and therefore support for the product - I may be lucky to get much of anything.
tmontagueCaledonia Ont. · May 28, 2019#216
Fyi I checked my heater hoses after picking the kids up from daycare andncollant was up to full temp (185F)

Both were hot to the touch and felt roughly the same temp, i couldnt determine if there was any temp difference.
ern-dizCA all day · May 29, 2019#217
Originally Posted by 06YarisRS ↑
Thanks ern-diz! I think, from a technical standpoint, the most challenging part remains - hooking up the F/IC. To be honest, I've done my best to figure out the wiring, but I'm not fully confident in my ability to have done that correctly. Let's just say I had to make some guesses based upon info from a variety of sources. No one has, as of yet, confirmed decisively that my wiring is correct. The guys at AEM said my diagrams look right, but they couldn't be sure as they were unfamiliar with the car's ECU. I may pester them again for more definite answers, but since the F/IC has been discontinued - and therefore support for the product - I may be lucky to get much of anything.
Fingers crossed!
eTiMaGoBangkok, Thailand · May 31, 2019#218
May I ask, what is the purpose of having both an oil catch can and a breather filter? Don't they both have similar function, taking positive air pressure within the engine and letting it out?
06YarisRSThread starterFredericton, New Brunswick, Canada · May 31, 2019#219
Originally Posted by tmontague ↑
Fyi I checked my heater hoses after picking the kids up from daycare andncollant was up to full temp (185F)

Both were hot to the touch and felt roughly the same temp, i couldnt determine if there was any temp difference.
Thanks! Mine seem to be coming up to temperature now. I'm going to assume that my system wasn't completely bled.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 31, 2019#220
Originally Posted by eTiMaGo ↑
May I ask, what is the purpose of having both an oil catch can and a breather filter? Don't they both have similar function, taking positive air pressure within the engine and letting it out?
The open-to-atmosphere breather is there to let blow by gasses out of the crankcase when the PCV valve is closed under boost. It would also draw fresh air into the crankcase when under vacuum. At least this is my understanding of how it should work. All that said, I'm having fuel trim issues and not sure if the two are related. I'll monitor trims after I have the F/IC hooked up and the car running- hopefully. LOL.
tmontagueCaledonia Ont. · May 31, 2019#221
Originally Posted by 06YarisRS ↑
The open-to-atmosphere breather is there to let blow by gasses out of the crankcase when the PCV valve is closed under boost. It would also draw fresh air into the crankcase when under vacuum. At least this is my understanding of how it should work. All that said, I'm having fuel trim issues and not sure if the two are related. I'll monitor trims after I have the F/IC hooked up and the car running- hopefully. LOL.
your breather shouldn't be the cause of any vacuum issues as it is not connected to the intake in any way. How you currently have it set up is smart as the PCV is normally closed under boost pressure and any blow by will not be able to vent - therein lies the solution of the valve cover breather.

The only way I could see this being a potential issue is during idle when the PCV in barely open and pulling mild vacuum on the crankcase. The breather technically allows fresh air to enter the valve cover and potentially out the PCV and into your intake. Since the PCV venting enters downstream of the MAF (IIRC) then it is unmetered air.

Easiest way to figure this out would be to block of your valve cover breather and see if the fuel trims correct themselves. If they do than a check valve on that breather tube to stop air from going back into the valve cover should solve that issue
06YarisRSThread starterFredericton, New Brunswick, Canada · May 31, 2019#222
Originally Posted by tmontague ↑
your breather shouldn't be the cause of any vacuum issues as it is not connected to the intake in any way. How you currently have it set up is smart as the PCV is normally closed under boost pressure and any blow by will not be able to vent - therein lies the solution of the valve cover breather.

The only way I could see this being a potential issue is during idle when the PCV in barely open and pulling mild vacuum on the crankcase. The breather technically allows fresh air to enter the valve cover and potentially out the PCV and into your intake. Since the PCV venting enters downstream of the MAF (IIRC) then it is unmetered air.

Easiest way to figure this out would be to block of your valve cover breather and see if the fuel trims correct themselves. If they do than a check valve on that breather tube to stop air from going back into the valve cover should solve that issue
You, sir, are a wonder! I was thinking about doing precisely what you mentioned with regard to blocking the breather hose and checking fuel trims. I hadn't thought about the check valve but may have eventually come to the conclusion to try the valve. So, you wouldn't anticipate any issues with, say, an extended period of idling and no way for fresh air to get back into the crankcase as it would stopped by the check valve. I guess I'm not sure I fully understand this system as the original valve cover vent was connected to the intake pipe before the MAF sensor, which, I assume, would also have vacuum on it. How would fresh air ever enter the engine if both the valve cover vent and PCV are under vacuum? Help me understand. LOL!

I am going to check my vacuum again this evening, but even with the open valve cover breather, I think I was getting around 25"/hg at idle. I'll monitor vacuum with the valve cover breather blocked off and not blocked off. BTW, I did test my oil catch can and it's sealed. When I started opening the ball valve, I could hear strong suction and the engine started to stumble. Close the check valve and idle went back to being smooth.
tmontagueCaledonia Ont. · Jun 1, 2019#223
Originally Posted by 06YarisRS ↑
You, sir, are a wonder! I was thinking about doing precisely what you mentioned with regard to blocking the breather hose and checking fuel trims. I hadn't thought about the check valve but may have eventually come to the conclusion to try the valve. So, you wouldn't anticipate any issues with, say, an extended period of idling and no way for fresh air to get back into the crankcase as it would stopped by the check valve. I guess I'm not sure I fully understand this system as the original valve cover vent was connected to the intake pipe before the MAF sensor, which, I assume, would also have vacuum on it. How would fresh air ever enter the engine if both the valve cover vent and PCV are under vacuum? Help me understand. LOL!

I am going to check my vacuum again this evening, but even with the open valve cover breather, I think I was getting around 25"/hg at idle. I'll monitor vacuum with the valve cover breather blocked off and not blocked off. BTW, I did test my oil catch can and it's sealed. When I started opening the ball valve, I could hear strong suction and the engine started to stumble. Close the check valve and idle went back to being smooth.
25mm/Hg in a good vacuum value during idle- I think I used to see 25-27 give or take on both my 1nz and 2zr back when I had a vacuum gauge set up. Have you checked what happens to your FT's when you hold 3k rpm?

I just checked my engine bay and what I thought earlier was correct: there is no vacuum hose that connects upstream (before) the MAF sensor and the only hose that connects before the TB is the valve cover vent. Because this hose is located prior to the TB, there is never really any vacuum on it. It would only really be able to "suck" air in during moderate to heavy throttle and even then, vacuum is very little at that point so it is more of a passive vent that happens to vent into the intake as opposed to an actual vacuum pulling air out of the valve cover.

Vacuum can only be had post TB as the TB restriction is what creates the vacuum with the help of the engine sucking air in. Think of a vacuum cleaner with a 5' diameter hose. You wouldn't ever really create a vacuum to suck dirt up. But with a 5" diameter hose or even less, you can suck dirt up.

I'm not sure why you think the crankcase needs to have fresh air go into it, it never really ever does. The crankcase never needs fresh air, it simply needs to vent excess pressure above ambient when blow by happens (it always happens, just at varying degrees). WOT and turbo motors create more blow by hence why people recommend turbo builds to have catch cans and/or breather set ups.

The 1nz and 1zz is much different than the 2zr in the way the PCV is set up. In the former engines, the PCV is located on the valve cover and it is the sole vent port for the crankcase (crankcase gases travel up into the head). This makes it easy to attach a catch can.

On the 2zr, the PCV is actually located under the intake manifold as you know, but it is attached to the engine block and separate from the head. Therefore there is also a breather tube on the head that runs into the intake before the TB - this is where you current breather it hooked up to. I am assuming Toyota did this as the head needs to be vented just in case of a situation where pressure builds up there (the highest location of the engine) since the PCV is much lower on the block.

Your PCV is taken care of with your catch can and your head is vented via your breather set up. None of this should cause a problem theoretically as the head should never have a vacuum in any situation and pull air in from your breather. That said, definitely clamp off the breather and see what happens to your FT's. Once that is done, rev your engine to 3k rpm and see what happens to your FT's.

Your engine doesn't need air going into it as it will never be in vacuum, the only thing it needs to do is be able to expel excess pressure from blow by out so as to not blow any seals. Years ago this was just vented to atmosphere as you have done with the breather. Ever since tightening emissions standards the PCV system has come to be the norm.

The PCV valve itself is virtually closed during idle and in any excess pressure situation (boost). It is fully open during WOT where there is little to no vacuum seen on it. In a boosted cars case, any time you are WOT you are usually in boost and therefore not venting the PCV. This is why a breather hose is typically a good idea.
tmontagueCaledonia Ont. · Jun 1, 2019#224
***EDIT*** jusdt looked at pics of the 1nz. looks like it does have a breather hose that takes air from the intake hose after the filer and MAF but before the TB

Just read some info that some systems (like in the 2zr) a filtered air source for the crankcase is included to replace the air that the PCV valve vents out. This is because in these systems the PCV valve works on a very small but present vacuum to keeps crankcase pressure minimal. This "sucked out" air from the PCV valce needs to be replaced with clean air to avoid the crankcase having a vacuum. This is where that other hose that is located upstream of the TB and enter the valve cover comes into play.

So are you earlier stated technically this hose (which is now your breather) does "suck in" air - I used quotations as it isn't ever actually a vacuums as the negative pressure are so mild. But it is there to act as a vent to actually pull air in and not necessarily out of the crankcase.

How the 1nz and 1zz motors get around this without having the vent hose is beyond me. Something tells me this second hose is a new addition to PCV system to improve their effectiveness and it was added to the much never 2zr but was never included on the 1nz and 1zz due to their elderly status.

With all of this said, it still shouldn't be the source of your FT issue, but to be sure, clamp it off and see what happens
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 1, 2019#225
Thanks Trevor. I blocked off the valve cover breather hose with my thumb while monitoring FTs. The suction on my thumb got stronger and stronger. In this situation the STFT actually started to climb and the engine rpm started to drop as though it was starting to struggle. At that point I removed my thumb and the idle went back to normal.

With the breather line open and around 3000 rpm, the STFT drops to about +6 to +7, down from +18 - +19, but LTFT remains at around +29. I'm leaning toward the different plumbing - airflow pattern/volume etc - throwing the MAF off and as a result the FTs and I hope that the MAF clamping via the F/IC should solve, or at least improve the situation. A lean code P0171 was finally set although AFR's always remain around stoich (14.6 - 14.8, so it seems the ECU still had control of fueling) and never deviated from that, except when the throttle was let off and it dropped to 18:1, but that's normal fueling strategy - my 1nz does that too as did the 2ZR pre-turbo.
tmontagueCaledonia Ont. · Jun 2, 2019#226
Hmm, the change you saw when when the engine r is what you would expect to see from a vacuum leak. Tje STFT will always adjust almost instantly but the LTFT will not until after a while, hence why it is a long term fuel trim.

That being said I have no experience with what a change in plumbing would do to FT's (other than my rich fuel trims seen after my exhaust install)

It's possible it's just your plumbing, but it is also possible that you have a vacuum leak somewhere. Use an incense burner or something similar that creates smoke - go in a garage so there is wind, open the engine at and let the car run. Move the smoke stick around your plumbing and see if the smoke gets influenced or "sucked in" anywhere. If not, than assume you have no leaks and just hope the piggyback ecu can adjust the fuel trims which it should.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 2, 2019#227
Thanks Trevor. Yes, I hope the F/IC MAF clamping will help the fuel trims. I'm pretty sure that the F/IC is going to be richening the A/FR anyway as boost comes on. I believe somewhere around 11.5:1 at high boost and rpm to help in preventing detonation. Hopefully my fuel pump can keep up. 😁

As an update, I was getting a fair bit of burned oil smoke in my exhaust and oil in the downpipe. The compressor side and charge piping is dry/pristine. The 3/8" NPT x 1/2" barbed fitting that drains into the oil pan has a slightly upward tilt (due to the backward stance of the engine) causing a little pooling of oil in my return line. I had replaced the steel braided hose with some clear braided water hose to observe the draining. Currently the drain line goes behind and under the axle. I am going to do an upgrade to 5/8" drain hose and route the hose over and in front of the axle. If I use a smooth 45 degree fittings on the turbo oil drain and the pan drain, I'll have lots of axle clearance. I'll also be upgrading the oil pan drain fitting from 3/8" NPT x 1/2" barbed to 1/2" NPT x 5/8" barbed. I think this will provide better oil return to the pan. I'm also upgrading the turbo oil drain flange to a 5/8" fitting as I think the 1/2 barb interior diameter (more like 3/8") is restricting the oil and I have considerable oil supply going into the turbo. I think the current setup is a bit restrictive and hindering timely draining from the CHRA, causing my smoking as oil backs up and leaks through the turbine side piston ring. I'll post pics of this process after I get my parts.

But, for now, I wrestled the oil pan off - yet again. While I have it off, I'll drill and tap a 1/8" NPT for my oil temp. Oh, and I received a fitting to add an oil pressure sensor. I haven't broken it yet to the finance committee that there is another fairly large expenditure in the offing - gauges. I'm thinking oil temp, oil pressure and trans temp should do. I wasn't going to do oil temp at all, but since I have the pan off... 😆 Torque can report on coolant temp, A/FR, boost etc.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 6, 2019#228
440 CC Fuel Injectors Install

Worst part of this job was cleaning all the sand out from around the injector holes without getting it into the cylinders. This took a long time using a small paint brush dipped in grease, Q-Tips with grease and then brake cleaner. I wish I'd had a small yet powerful vacuum with a tiny nozzle. It would have made the job a lot easier, for sure.

Anyway, job is done. I guess I can't start the car again now without having the piggyback installed and the plugs gapped from .044 to .028. I still have to finish my turbo oil drain and parts are on order and should be here early next week. Then I'll drill and tap a 1/8" NPT for the oil temp gauge and reinstall the pan. Normally, I would be really excited about a gauge installation, choosing the gauges, deciding where to place them, etc, but honestly I'm not looking forward to that process at all.

Fuel rail removal:

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Getting all the junk out of the way:

Picture not included in this copy

Lubing the injectors for installation:

Picture not included in this copy

Injectors installed

Picture not included in this copy

All done

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 8, 2019#229
F/IC Wiring Prep

Dug out the F/IC Install Manual and my diagrams I made (and posted on page 1) specific to my ECU. Here, I am just eliminating all the wires that I will not be using for my install. I'd rather not cut these off as the ends are nicely labeled, but tucking them backwards into the harness will make it a lot thicker and necessitate a larger hole through the firewall. I may just extend the harness, containing only the wires I use by putting them in a separate piece of conduit and send that through the firewall.

Picture not included in this copy
MaritimeWoodstock nb · Jun 8, 2019#230
Getting so close to tune time. I hear you on the oil guage. It's not as fun as others to install. Keep up the great work. This rhing is going to be insane when you are done.

Sent from my moto e5 play using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 8, 2019#231
Originally Posted by Maritime ↑
Getting so close to tune time. I hear you on the oil guage. It's not as fun as others to install. Keep up the great work. This rhing is going to be insane when you are done.

Sent from my moto e5 play using Tapatalk
Yeah, getting there, haha. I had to send AEM an email asking about the grounds. There are 2 Power Grounds and 1 Signal Ground in the F/IC harness. I'm struggling to find where to tap these wires in. Hopefully AEM can provide me with the answer.

I just got off the phone with the guy who will be tuning my car and among other things, we discussed my catch can set up. He strongly advises capping off my pcv system at the block and manifold and moving my catch can - well, actually another catch can (mine is sealed and he suggests vented) to the vent side. He tells me I should connect the catch can to the valve cover vent. Depressing! This is advice contrary to what I've been told by the turbokits guys. I can see how the PCV system might leak a little boost into the crankcase, but what would pull all those nasty gasses out if there's no PCV system anymore? The tuner thinks that my lean condition and positive fuel trims will be cured if I follow his advice. So much contradictory advice abounds... 🙄 It would be nice to just know what to do rather than weighing out opinion after opinion and trying to figure out the best route.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 8, 2019#232
F/IC Wiring Begins 😲

Home of the F/IC will be somewhere in the area below. I have predrilled my hole in the firewall. All I need now is about a 1" - 1 1/4" hole saw and an appropriately sized grommet. Knowing nothing about available sizes, I'm going to have to research this. The F/IC harness is probably 5/8" - 3/4" in diameter. Haha, just noticed that little blue wire - that's connecting the "CT Scott" cruise control to the ECU. I must secure that wire!

Picture not included in this copy

Tracing wires. Recall that I am using a 2008 xD ECU and a 2011 xD wiring harness. I was going by wiring diagrams and not comparing to the car until tonight. Happy to say that all the wires I've checked against my proposed wiring appear to be matching colors and pin locations in the ECU plug. So far I've confirmed switched power, MAF, Cam 1 (intake), Cam 2 (exhaust), all 4 fuel injectors and the crank. Just have to confirm 02 sensors. I'm going by the fundamental rule that MAG sensors have 2 wires and Hall sensors have 3 wires. It's confusing because the AEM F/IC manual says that cars use one type or the other, but not both. My cams are 3-wire and my crank is 2-wire. Still all ears for any guidance on this. The dealer was no help; don't know which type of sensors they are and of course Toyota Canada just sends me back to the - in this case - useless dealer. Fingers crossed. The red circle is the approximate location that the harness will come through.

Picture not included in this copy

Culling unnecessary wires. These will remain bundled up under the dash with the F/IC as much as I want to hack them off, or remove them from the connector.

Let the soldering, heat-shrinking and wrapping begin! Actually, it'll be a few days before that process starts.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 9, 2019#233
More F/IC Installation Pics

I use a 1 1/4" bi-metal hole saw to cut through the firewall. Why so big, you ask? The F/IC harness is thick and I also have to pass a split loom through for gauge wires as well as the small vacuum line for the F/IC MAP sensor. There should be just enough room. Once it's all in there, I'll glob in some RTV to seal it up. It's not really in an area that gets any water, so this would probably not be necessary, but will do it for good measure.

Hole saw. After I cut through, I painted the bare metal and let it dry.

Picture not included in this copy

Reflecting on simplistic algebra I learned in school, I used C= pi x D to figure out how long a piece of rubber vacuum line I needed. I sliced the vacuum line and worked it into place as a 'grommet'. A little RTV on it before installation should keep it in place, but it's mighty secure without the RTV.

Picture not included in this copy

Picture not included in this copy

This is not the final placement of the F/IC. I will likely secure it to the upper kick panel area behind the glovebox and run the USB laptop interface into the glove box.

Picture not included in this copy

Lovely spaghetti to sort out...
Picture not included in this copy
tmontagueCaledonia Ont. · Jun 9, 2019#234
looks good, good luck!

are you using an oil restriction plate on your turbo oil inlet?
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 9, 2019#235
Originally Posted by tmontague ↑
looks good, good luck!

are you using an oil restriction plate on your turbo oil inlet?
Thanks! I'll need it.

I'm going to try my upgraded drain system first to see if it allows the turbo to drain quicker. The turbokits guys sent me a restrictor .06" that attaches to the fitting at the block as opposed to at the turbo oil inlet. If my smoking is cured by the larger drain, I won't install the restrictor. Despite what I've read online, I've been assured that a .06" restrictor is perfectly fine for a journal bearing turbo. Apparently they have a number of kits running with the restrictor. As a matter of interest, what oil pressures do you see routinely under low and high revs?

I've been struggling to figure out how to fix my fuel trim issues. My tuner says ditch the PCV altogether by blocking off the manifold and PCV. He says to use a vented catch can on the valve cover side. He believes it will fix my fuel trim issues 🤷. I like the idea of my crankcase being evacuated of all that crap. I'm not sure if I could run a hose from my valve cover to a sealed catch can and then into my 3" intake (pre-turbo) and if that would make any difference. Theoretically, no "new" air would be introduced into the system and there would be vacuum. But, then again if the vent is to allow air into the block as the PCV allows vacuum to clear the block, maybe these two sides would be fighting each other. I know that the F/IC has a MAP sensor built in and apparently MAP is unaffected by vacuum leaks or unmetered air. I have an email in to turbkits asking them to explain this. There isn't anything in the manual that talks about how to deal with the PCV/breather system and there's definitely no return fitting post MAF and pre-TB as in the stock system. I had a look at the F/IC fuel map today and it shows negative numbers that actually seem to parallel the positive fuel trims that I'm seeing. That said, I don't really understand the tables - yet. Maybe all my fuel trim issues will be resolved with the F/IC install.

Here is the latest I've been reading. About 1/2 down the page, "Keith" seems to explain it in a way I can comprehend. It's where I got teh idea to plumb the valve cover hose through a catch can to my custom 3" intake.

https://grassrootsmotorsports.com/fo...l/11243/page1/

Feel free to speculate if you care to.

Thanks.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 12, 2019#236
Fuel Trims and Toyota 02 Sensors and some updates

If found an interesting article on Toyota oxygen sensors. Most of the reading I've done online suggests that downstream 02 sensors are not related to fuel trims, but it seems that some Toyotas do infact collect data from the post-cat sensor which may influence fuel trims. From paragraph 22: "Since Toyota allows the rear O2 sensor a surprisingly large authority over fuel trim, you’ll want to test it carefully as well. (Many generic interfaces call out the rear O2 sensor’s contribution to fuel trim separately under a heading such as FTB1S2.)"

https://www.motor.com/magazine-summa...ta-af-sensors/

Right now, my downstream sensor is just hanging beside my downpipe.

As mentioned my fuel trims are out of whack. Speaking with the turbokits tech support, the issues should be resolved when the F/IC is hooked up. There is a distinct difference in how the stock MAF sensor is mounted vs in the kit charge piping. In the stock application, the intake pipe narrows and appears to direct all of the air through the sensor. In the kit, the MAF sits in the middle of the free-flowing piping. The MAF clamp feature of the F/IC caps the voltage to around 5 volts which keeps the ECU from going snaky with higher voltage inputs.

Pic of the MAF housing in stock airbox:

Picture not included in this copy

I'm continuing to try to figure out all possible causes of my high trims - or maybe more appropriately, what factors could contribute to a lean condition. With the valve cover vented to atmosphere, it draws fresh air into the crankcase as the PCV vacuums out the combustion byproducts. Because this new air from the valve cover breather is then drawn into the manifold via the PCV system, it could be considered unmetered air. I have been receiving a number of different theories and suggestions from different sources. One guy says that I should be fine with my current setup as the crankcase has nothing to do with the vacuum system. Another source says that introducing air directly into the crankcase via the valve cover breather will definitely introduce unmetered air and make the car run lean. The guy who will be tuning my car says to remove (block off) the PCV system at the manifold and PCV valve (at block) and run my catch can with a breather on it on the valve cover breather. Yet another source suggests, blocking the manifold PCV intake, removing the PCV and putting a breather on that along with my valve cover breather. Lots of suggestions!

On another note, I have been advised to not attempt to have the F/IC control the VVTi and with regard to timing, all that's needed is the crank sensor at the relatively low boost that this kit will have.

I will also be changing my source of power to the F/IC from my original proposed pin 28 on connector A21 to the #1 EFI switched/fused circuit.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 13, 2019#237
Turbo Oil Drain Upgrades and Overall Wiring Diagram

I'm in the process of upsizing my oil drain. I started at around a 9.8mm diameter, then 12mm and finally 14mm (left to right). The 14mm bore should be able to handle 2 to 2.5 times as much oil as the 9.8mm bore. I'll be going from 1/2" drain to 5/8" and a shorter and straighter shot to the pan.

Picture not included in this copy

Unfortunately, my package depot lost my 45 degree fitting which is a major inconvenience as I'll have to wait another week to finish the drain. Big bummer.

I printed, spliced and laminated the wiring diagram pages into one long document. This is the Engine Control schematic, with the long narrow blue bar representing a portion of the car's ECU.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 15, 2019#238
More on the new drain and Oil temp sensor port

My drain is finished. I put the pan back on this evening so I'll test the drain tomorrow with the clear tubing and if leak free and smoke free, I'll replace the clear tube with the braided hose.

Almost lined up. I'm going to reclock the turbo CHRA. It is about 8 degrees off vertical. The drain fittings should line up near perfectly with the turbo clocked back to vertical.

I had to bevel off the 45 galvanized fitting as it wouldn't turn without hitting the block. Most of the threads a well below the collar that I ground off. The barbed fitting isn't cranked down in yet, just test fitting for alignment. I have tons of clearance above the axle. The outboard end of the axle would basically have to be sticking out the quarter panel to even get close to my drain.

Picture not included in this copy

Picture not included in this copy

Oil temp sensor port drilled out to 11/32"

Picture not included in this copy

Tapping

Picture not included in this copy

Temporary sensor in pan. This is an old sensor I had left over from some cheap Chinese gauges I have on my shelf collecting dust. I'll drain my oil and replace with the actual sensor from whichever gauge I buy. I like the positioning of the sensor - right below the turbo drain. In this location, I should get nearly the highest reading in the lube system.

Picture not included in this copy

Sensor in with Permatex thread sealant. Pan reinstalled. Hopefully no leaking at pan or sensor.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 16, 2019#239
Breakthrough on Fuel Trims...maybe

I was taken by suprise on this one. I finished up my drain with the test hose so thought I'd check the oil flow. A little backstory first...

I wasn't sure the car was going to start with the new injectors in it. I cranked the car over and could immediately smell a very strong gas odor and the car would not start. Fuel was pissing from my fuel rail. So, I pulled the rail off and the injectors out and 3 of the o-rings were torn/squished. They did seem a little tight going in but no tighter than taking them out. The reason I didn't swap out the o-rings from the stock injectors was because the Deatschwerk o-rings on the injectors looked identical in size. Anyway, I swapped in the stock o-rings. The injectors seemed very loose in the fuel rail and I was worried that I'd have to order new o-rings. I know that the rail bolts hold the rail in place but I figured with as loose as the injectors were, I'd definitely have a leak. Well, they sealed perfectly and the rail is still bone dry after a good 20 minutes of running the car.

The great news - I hope - is that my fuel trims have leveled out nicely. STFT oscillates between 0.0 and - 0.8. LTFT is still creeping down from it's +29 to around - 5.5 in the short time running. I would expect it to run a little rich and the ECU to pull a little fuel with the larger injectors, so this looks promising. The F/IC is still not installed. I do not understand how the larger injectors leveled the trims as the car is running well out of boost and there are no other variables that I am aware of.

Also, on a positive note, my oil drain seems to work much better and I have no smoking anymore at either Idle or 3500 - 4000 rpm.

Picture not included in this copy
ern-dizCA all day · Jun 17, 2019#240
Great news!
CrankyOldManWest Michigan · Jun 17, 2019#241
Awesome news!

I know NPT threaded parts are cheap and readily available at the local hardware store but they suffer from the exact problem you had--limited flexibility when installing in a tight place. There are a few other standards out there from the hydraulics world that might make your life easier should you need to revisit or clean up the plumbing: SAE, JIC, O-ring boss, etc. The ones with an angled/flared end can usually be clocked any way you need and tightened down without rotating the connection. You can usually get custom hoses with the connectors crimped at a local hydraulics supply for a modest price once you nail down the placement of the connectors.

How much longer before this thing can go out and terrorize your neighborhood? =D
tmontagueCaledonia Ont. · Jun 17, 2019#242
great to hear the FT's smoothed out. I'm really surprised as to how a potential fuel leak could have caused this issue as it should have run rich not lean, but either way glad it seems settled.

I guess the issue with your turbo oiling wasn't too much oil going in but not going out at a fast enough rate? That said, is it possible you had too much oil supplied to the turbo where you need such a large drain tube? I can't see too much oil being a problem as long as you can drain it adequately, it just seems like a much larger diameter drain tube than I have ever seen before.

After following your in depth turbo build I fully understand why long time track rats tend to say that an all engine build is superior to a boosted set up for a track car. This is by no means knocking your turbo build - I think it is awesome and will be a completely original and fun DDer - I just mean from a track car point of view. Many more fittings for potential oil leaks and therefore dangerous and costly fires (which happen a fair amount at the track). More heat to have to cool and many more fittings and parts to have to constantly check to ensure it is all working fine.

Obviously this is a bigger chore in a car that was NA form the factory, but I can see why people talk about turbo'd Miatas constantly needing work and they tend to be down more than they're running.

Good work thus far, I'm excited to hear about your thoughts on driving it once it is fully functional.

Side note - I would recommend you purchase a fire extinguisher to have in your car once it is fully operational. All it takes is a small oil leak to cause a fire that can write off your car, vs a small mess to clean up and some wire to repair.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 17, 2019#243
Originally Posted by ern-diz ↑
Great news!
Getting pumped here! LOL!
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 17, 2019#244
Originally Posted by CrankyOldMan ↑
Awesome news!

I know NPT threaded parts are cheap and readily available at the local hardware store but they suffer from the exact problem you had--limited flexibility when installing in a tight place. There are a few other standards out there from the hydraulics world that might make your life easier should you need to revisit or clean up the plumbing: SAE, JIC, O-ring boss, etc. The ones with an angled/flared end can usually be clocked any way you need and tightened down without rotating the connection. You can usually get custom hoses with the connectors crimped at a local hydraulics supply for a modest price once you nail down the placement of the connectors.

How much longer before this thing can go out and terrorize your neighborhood? =D
Great advice Sam! I really just started fooling around with what I could source locally. I didn't expect it to work well and it's a bit of a hack job. That said, it seems leak free, flows very well, but I'll def keep my eye on it for leaking. If it holds up well, I may leave it as it's well hidden away there. Then again, my tuner might take one look at it and insist that I do something different. We shall see.

Well, I have an appointment for my exhaust work in a week and a bit, then my dyno tuning session on 15 July, so I'm gonna say I'll be in terror mode on 15 July! Though, for the first while, the terror will be mine. LOL!
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 17, 2019#245
Originally Posted by tmontague ↑
great to hear the FT's smoothed out. I'm really surprised as to how a potential fuel leak could have caused this issue as it should have run rich not lean, but either way glad it seems settled.

I guess the issue with your turbo oiling wasn't too much oil going in but not going out at a fast enough rate? That said, is it possible you had too much oil supplied to the turbo where you need such a large drain tube? I can't see too much oil being a problem as long as you can drain it adequately, it just seems like a much larger diameter drain tube than I have ever seen before.

After following your in depth turbo build I fully understand why long time track rats tend to say that an all engine build is superior to a boosted set up for a track car. This is by no means knocking your turbo build - I think it is awesome and will be a completely original and fun DDer - I just mean from a track car point of view. Many more fittings for potential oil leaks and therefore dangerous and costly fires (which happen a fair amount at the track). More heat to have to cool and many more fittings and parts to have to constantly check to ensure it is all working fine.

Obviously this is a bigger chore in a car that was NA form the factory, but I can see why people talk about turbo'd Miatas constantly needing work and they tend to be down more than they're running.

Good work thus far, I'm excited to hear about your thoughts on driving it once it is fully functional.

Side note - I would recommend you purchase a fire extinguisher to have in your car once it is fully operational. All it takes is a small oil leak to cause a fire that can write off your car, vs a small mess to clean up and some wire to repair.
Hey Trevor. The car never ran with the leaking fuel rail. The high trims were with the stock injectors.

The turbokits guys sent me a restrictor and I've read that some journal bearing turbos do use them if the drain has been confirmed good. From my reading, this size turbo should ideally have a 14mm + drain. Initially, I was around 9.8mm and I'm now close to 14mm. I do believe that the turbo CHRA couldn't drain off the oil fast enough and I wanted to confirm that was the issue before I went ahead with the restrictor, which is a Vibrant (0.06", 0.045" and 0.030" adjustable with pills.). If I get smoking on steep hills or otherwise, I plan to drill out the Vibrant restrictor to 0.080" or 0.090". Right now the oil supply fitting that came with the turbo is 0.118" (around 3mm). I think I have enough drain to handle a very solid oil flow.

I get your points about a track vs turbo track car. I hope that the turbo 2ZR auto will prove to be a fun DD. And, yes!, I have a fire extinguisher. Any leaks that I get in my drain plumbing (zero pressure) would likely not get anywhere near the manifold or turbine housing and drip down to cooler areas. But, yeah, if say the oil feed line broke and started spewing oil onto the manifold/turbine, I bet it could make quite a fireball.

As an aside, I have a lot of reflective fiberglass heat shield tubing that I'll be putting on all the lines (oil supply, water lines, upper drain area etc). Fortunately, all hoses and supply lines are well clear of the really hot parts.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 17, 2019#246
Ordered gauges today...

After lots of searching, I decided to go with Prosport Performance Series gauges. The reason...budget and the fact that I found an amazon listing for the oil temp gauge at $13.00/ea (regularly ~ $50.00 a pop - must be a closeout, or something). So, I ordered 2 of those; one for oil temp and one for trans temp. I also ordered an electrical oil pressure gauge. Not bad, I guess for around $110.00 CAD. I read a bunch of reviews and people were generally very positive about them. I expect that they are a competitor for the Glowshift gauges. I think I'll order the eBay 3 pod gauge as well. So for around $160.00 CAD, I'll have my gauges installed on the A-pillar. I didn't really wan to mount them there, but there aren't many other good locations Also, discovered that Princess auto has all their multi color primary wire on sale this month. Bonus!

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 18, 2019#247
Transmission temp sensor housing

I decided to build my own rather than wait for parts ordered online. I found a 1/2"NPT x 1/8"NPT tee at a local hardware store. This is better than other offerings, IMO, as the interior of the fitting is larger so the sensor probe will not restrict fluid flow in any way. I had a couple 1/2"NPT x 3/8" barb fittings. Although this is a bit of a heavy rig, it will be supported by the hose over the brass barbs with my rubber coated P-clips (these things have been indespensible in my build) bolted to the subframe. I wrapped the fitting with a piece of rubber hose around the contraption as it will be contacting the subframe, tightly though, so there should be no chafing. I've always had good luck with the Permatex Ultra Black as a thread sealant - especially larger, more coarse threads. I'll monitor the zip ties and if they look like they're not handling the heat, I'll use a couple of my steel zip ties. The nylon ties have a melting point over 400F, so the should be fine. Even if they did come off, the rubber hose is glued on with the Ultra black and the whole unit is held tightly against the frame with the P-clips. I can't see the rubber going anywhere. On the sensors (1/8"NPT), I'll use my Permatex High Heat Thread Sealant. The old sensor in there is just a temporary seal until my gauges arrive.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 21, 2019#248
Evap Hose and Oil Catch Can

I installed my catch can and because I didn't have any hose, I picked up some rubber fuel hose from the local parts store. It seemed quite firm, but completely failed under vacuum. It basically sucked flat. So, I went to a local hydraulics shop and picked up some Pulsar 4000 psi hose. Not cheap at ~ $5.95/ft, so thankfully I only needed about 2.5 ft. They had some cheaper stuff at $2.49/ft but it was heavily steel reinforced rubber and I was worried that I wouldn't get a good seal with a clamp as it was so rigid, plus it seemed less flexible than the Pulsar stuff. The Pulsar hose appears to be constructed with a very thick teflon liner. I tested it with my 3/8" barb fittings and it seals well. It may not even require a clamp, but I'll put one on for good measure.

I had no idea that the vacuum produced by a car could completely flatten a rubber hose. These is no way that this Pulsar hose will even be slightly deformed by the vacuum. It's designed to handle 4000 psi (outward pressure of course), but I could barely deform it squeezing as hard as I could. I'll report back on how it holds up.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 22, 2019#249
Turbo Drain...Take 3...

When I designed my new turbo drain, I thought I'd accounted for enough room of axle movement vertically and horizontally. I had taken into account the fact that the car's suspension was fully extended as the car was on jackstands. After lowering the car onto blocking today, I had about the clearance that I was expecting but I'm not fully confident that in an extreme braking situation combined with a bump that the axle would clear the fittings. This would be particularly devastating as the galvanized fittings would smash forward and probably take a chunk of the block (where the oil pan inlet is) with it.

So, I removed a couple of the fittings and went straight vertical with the hose and joined the 45 under the turbo. There is a good curve but smooth and the hose has fully retained it 'roundness'.

***Nerd Alert***: I took some measurements:

3.5" upward vertical deflection for outboard of axle to contact frame. The is a little indentation in the frame, presumeably in the event of the worst possible nose-down scenario combined with running over a log or something for the maximum possible deflection.

22" from inboard CV joint to area where axle would contact the frame - a highly unlikely event. The axle is close to 28" hub to hub (excluding the splined sections), so the wheel would basically have to be well into the engine bay, I'd think, by the time the axle bottomed out on the frame.

6" from inner CV hub to where drain line crosses over axle.

1.75" vertical distance between drain line and axle.

Using a slope calculator, I should have more than adequate clearance. Also, as the wheel hub deflects up and down from center, the pivot point of the axle would move outboard, allowing me even more space between the axle and drain line. I will wrap a bit of tape around the drain hose just above the axle and check it for evidence of contact. Even if it did make contact, it's now going to hit a flexible line as opposed to steel fittings.

I have about 1" clearance horizontally between the pan fittings and axle. When I had the rear lower mount (dog bone) out, I could rock the engine and forward until it hit the radiator and rearward until it hit the subframe. Even with these extreme movements, the axle would not contact my drain line. The engine will likely tilt forward at the top due to the mount geometry. I did stiffen my dogbone mount, so I expect movement near the inner axles will happen but it should be pretty minimal. That said, I might turn the galvanized elbow in another turn just to be super safe. The axle should tend to move away from the drain as the bottom of the engine torques forward, while accelerating in a forward direction. I guess there's no real way to know. Maybe I need a GoPro. lol


Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
MaritimeWoodstock nb · Jun 24, 2019#250
Nice work as always. so close to the day it is fully set free to roar down the road.