Yarisworld Archive

2ZR Turbo Yaris

561 posts · 343,257 views · page 3 of 12

Replies continued

CrankyOldManWest Michigan · Apr 2, 2019#101
Yeah, the HVAC unit is a real monster to get out. I took a Yaris dash completely apart at the junk yard once and wasn't able to get it out. I think this is why some setups have moved the turbo into the air box space.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 2, 2019#102
Originally Posted by CrankyOldMan ↑
Yeah, the HVAC unit is a real monster to get out. I took a Yaris dash completely apart at the junk yard once and wasn't able to get it out. I think this is why some setups have moved the turbo into the air box space.
Hey, Sam. Yeah, it's in there pretty good. At lunch, on a whim, I went out to the parking lot and peeled back the carpet on my '08. If I'm correct, I have avoided damage to the unit as the mounting points seem to straddle the area that I pounded in. I'll check the actual car when I get home to confirm. There appears that I may have had just enough room to make the indentation. I wish I still had my borescope, then I'd know for sure.

Update: Fortunately, no damage to the HVAC that I can see. Removing the glovebox helps as well, but I can see from the passenger side that the dent lands, as suspected, between the plastic mounting tabs on the HVAC module. Yay!

Primed and painted "dent".

Picture not included in this copy

If I get time tonight, I hope to take the dogbone off, clean, degrease that and fill it with urethane. With the dogbone removed, I'll be able to rock the engine a bit to see how much actual clearance I do have. If clearances are good, I'll degrease, prime and paint the depression. Also, planning to trim that fugly firewall blanket.

Next Steps:

- Drill hole and tap for oil return fitting

- Mount turbo, permanently (done)
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 3, 2019#103
Tonight's Tinkering

When I was under the car removing the dogbone to fill it with urethane, I had a mild panic situation as I noticed that the compressor out nozzle was aiming directly at the subframe, several inches from a direct down shot to the space between the axle and the subframe. I assumed that in the Corolla the opening is much larger and the pipe went straight down through. So, I started calculating that I'd need an offset coupler (if such a thing exists) a bit of pipe and a few clamps. Much to my delight, I dug through my boxes and then referred again to the install manual, and there is a 45 coupler that attaches to the compressor outlet and the pipe it joins also starts with a 45. A little trimming (which you have to do too with the Corolla) and the piping fits perfectly! So happy!

Picture not included in this copy

Picture not included in this copy

The other thing I did tonight was fill my mount with urethane. The mount was a bit rusty and a bit of the rubber at the top had started to peel away as rust formed under it. I trimmed off these small sections, scraped off the rust. I wire brushed the complete mount (rubber and all) with soapy water and the degreased with lacquer thinner. I also bored out the holes a bit so I could get full contact through the mount.

I probably wouldn't have had to strengthen this mount at all as when I removed the dogbone, I could rock the engine a bit. At it's farthest back position - where it contacts the rubber seal on the subframe, the turbo still had about 3/4" clearance. The engine won't go back that far I'm sure anyway with the dogbone in. On the upside, maybe I'll get a little better power response with the tighter mount. If it's too rough and I don't like it, I'll either drill a few small holes in it or order a new mount and install that.

Picture not included in this copy

Picture not included in this copy


Finished Mount. Man, this thing is stiff! And, I don't think it's 100% cured yet. I lathered the mount with rust converter and let it sit for about an hour. Then washed it, 2 coats of primer and 3 coats of rust paint. While it's out, I'll clean out the recess in the subframe and shoot some Fluid Film in there. Fortunately the recess is pretty much rust free as I'd blasted product in there during my rustproofing sessions.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 6, 2019#104
Hoping to do the turbo oil drain this evening. It will involve draining the oil, removing the pan, drilling a 9/16" hole in the block, tapping for 3/8" NPT, installing and sealing the nipple with high temp RTV.

As much as I wanted to buy a pneumatic angle drill for my compressor setup, I couldn't justify the cost, so I went with the DeWalt angle drill attachment. Also picked up a 3/8" NPT tap at Princess Auto for $7.49 and a 3-pack of step bits for $12.99.

Canadian Tire had Pennzoil Platinum on sale - about the same as what I'd pay stateside at Walmart, so I grabbed one of those jugs. I'll run full synthetic from now on in this car.

Picture not included in this copy

Update: This job is almost done:

Pan removal. Such a pleasure working on an engine that is relatively new. Bolts came off so easily.

Picture not included in this copy

Toyota sure loves their RTV. Took about 1/2 hour to get the pan off without damaging the pan itself or the mating surface. I used a thin bladed utility knife, carefully, around the perimeter between the pan and block.

Picture not included in this copy

Pan Off

Picture not included in this copy

A+ DeWalt. 90 degree attachment worked like an absolute charm.

Picture not included in this copy

This part was scary. I've tapped lots of sheet steel but never cast. The tap cut nicely with lots of rotations and counter rotations, but I was afraid that the block was going to crack. 9/16" hole drilled for 3/8" NPT threads.

Picture not included in this copy

Threads in perfectly and should be almost touching the block when tightened down with teflon tape and then high temp, oil-resistant RTV on both sides of the fitting.

Picture not included in this copy

Tomorrow, I'll go out and thoroughly clean out all the tiny metal fragments from drilling and remove all the old RTV from the mating surface. I'll use plastic razor blades to ensure no damage to the mating surface. I'll wash everything down with thinner for a better bond with the RTV both on the mating surface and the new fitting, then use compressed air. Finally, reinstall the pan and connect the hose from the turbo drain to the new fitting.

My son has a hockey tournament today, so I may not get much done beyond the above.

Next steps:

- attach new "tee" adapter to oil pressure sensor port on engine
- run turbo oil supply line from "tee" to turbo
- intercept heater hoses with coolant supply lines for turbo
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 8, 2019#105
Oil pan has been reinstalled. I'll retorque the bolts tomorrow as well as clean up the RTV on the bottom of the pan.

Picture not included in this copy

Turbo end plumbing done and wastegate actuator reinstalled. I have to cut about 2 inches off the steel braided oil return line as it will rub on the subframe. The Yaris has a smaller opening at the front of the subframe which would account for the shortening of the hose. Not sure how I'll cut the hose, but it will likely involve unwinding the braid then cutters or a hacksaw to cut the rubber. The two outside hoses are the coolant in and out and the middle (larger hose) is the oil return.

Picture not included in this copy

Just found a video on a good way to cut the braided hose.

https://www.youtube.com/watch?v=lwcVAyarCHM

UPDATE: Cut and hooked up oil drain hose. Also cut and connected the compressor to waste actuator pressure tube. Last night I got thinking about whether or not I had cleaned out the pan and lower block well enough. From the drilling there was a lot of swarf (aluminum filings) from the drilling and tapping process. I had cleaned it reasonably well, but my mind got the better of me, so I removed the pan again tonight and made sure there was nothing left in there. It was actually really clean but I blasted the area (well below the crank and main bearings) thoroughly with brake cleaner, use numerous microfiber cloths and compressed air. It's spotless now. The oil from the pan is routed through the pump to the oil filter so I expect nothing would have gotten through, but I've spent too much time and money to have the engine and turbo destroyed by some rogue filings.

Picture not included in this copy

Next Steps:

- hook up oil supply fittings at pressure sensor port
- hook coolant lines to the heater hoses
- Install downpipe
- Install K&N turbo compressor intake air filter
- install transmission cooler (I bought a tube and fin cooler a few years ago and never used it.)

Once everything is bolted up - and before the AEM F/IC is wired in - I'll verify oil flow through the supply line (disconnected from turbo) turning the car over without starting. I will prime the turbo with oil just in case I detect an oil supply issue. I'll have to look up which fuses to pull to kill the ignition and injectors. Then I'll run the car and check for oil and water leaks. In the meantime, I'll be ordering an oil pressure gauge and will have to swap the fitting that comes with the kit for a tee to add the oil pressure gauge.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 12, 2019#106
OK, so this is where some of the real modification begins. Any parts that are directly connected to the engine, I'll try to keep a small space on the order of 1/4" and I'll glue rubber pads on possible wear areas. I'm hoping to achieve 1/2" - 3/4" or more between piping and chassis parts, but this will be a challenge. Again, rubber pads and or sections of split rubber hose will be glued in all possible wear areas. I'm just loose fitting everything for now. It will all come apart, cleaned and obviously attached with the T clamps.

I was very happy that I did manage to get the MAF pipe in and down below the headlight. This was the piece that I figured would need to be cut and coupled, but I got lucky. I may have to move back or slightly downsize my battery as there's only about 1/4" clearance between it and the MAF pipe. Fitting it in there did require unclipping some of the small harnesses and tapping over a few tabs, but I'll re-secure the wires when I'm done.

Picture not included in this copy

There are going to have to be mods done to the intercooler piping. The pipe that connects to the driver's side of the intercooler will require about 6" cut off, bead rolled and a 45 degree 2.5" x 3" silicone coupler. Some metal needs to be removed to attach to the intercooler. On the upside, it looks as though all of the piping will tuck in close enough to the car that none of it should interfere with my bumper cover/foglights etc. That's a bonus, lol.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

The left side of intercooler will also require mods, This one is fairly simple. I'll have to cut 3" - 4" inches off the aluminum piping, bead roll the end and attach the 90 degree 2.5" x 3" coupler.

Picture not included in this copy

Picture not included in this copy

Here is another challenge. The Corolla has a much wider opening in the subframe. I had initially thought that I'd have clearance but I don't. The 45 degree coupler that connects to the turbo and goes down to meet the pipe is touching the subframe. I could clock the turbo a few more degrees, but that would put a little side pressure on the wastegate actuator arm, which I am reluctant to do. I may have to buy a couple of different couplers and try to sidestep that pesky subframe. It's also just touching the oil return line. I'm not worried about heat or chaffing as the two will move together as they are both one with the engine. However, I'll try to figure something out to remedy that.

Picture not included in this copy

This section of pipe should be fairly easy but may also require a little trimming and bead rolling to shorten the overall length. This pipe has to go up but also much closer to the oil pan.

Picture not included in this copy

Here's a front-on shot. Please excuse the mess. I think tomorrow I'll go out and do some tidying.

Picture not included in this copy



So, overall I'm fairly happy about how this part of the project is going. I hadn't intended to tackle the charge piping at all this eveing, but I did remove the airbox because I'm trying to address another probem that could only be tackled with the removal of the airbox and the MAF pipe in situ. Anyone care to guess why I'm looking for extra space in the engine bay? 😁
tmontagueCaledonia Ont. · Apr 12, 2019#107
I would recommend just taking an air hammer or cutoff wheel to the flat part of the subframe touching the pipe from the turbo (then repaint).

That part isn't very sructural and is mostly just left over from when the steel is stamped. That is the part of the subframe I air hammered on mine to better clear the transmission to make it easier to remove and re install.

Good work so far, this is coming along nicely
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 13, 2019#108
Originally Posted by tmontague ↑
I would recommend just taking an air hammer or cutoff wheel to the flat part of the subframe touching the pipe from the turbo (then repaint).

That part isn't very sructural and is mostly just left over from when the steel is stamped. That is the part of the subframe I air hammered on mine to better clear the transmission to make it easier to remove and re install.

Good work so far, this is coming along nicely
Thanks! I will do this as you recommend, however, it's the upper rounded corner section of the sub frame that the hose of hitting. It's actually not touching the stamped steel lip, but it might when the engine torques, so, yes, I will do as you recommend. The challenge will clearing the upper forward part of the subframe. It's likely going to require some combination of couplers. I'll try to get a better pic of what I'm describing.

My other issue is that I have very little room for an air filter. The smallest filter that even stands a chance of fitting between the turbo and frame/firewall has a flow rate of 283 CFM (K&N RU-2420). The filter that comes with the kit (K&N RU-3700) is rated at 380 CFM. According to various CFM for boost calculators, I'd be close to - if not slightly over the limit with the 283 CFM filter at 0.55 bar (~8 psi). I'll post a link to a couple calculators below. So, this brings me to the question of which approach to take. I'd love the have a large filter positioned where the stock airbox goes for a few reasons: colder air, larger CFM and less chance of filter loading from road debris resulting in reduced filter flow rate. But, obviously that necessitates an extensive custom intake set up which is both expensive and complicated to install.

My target is about 7 psi boost, so I could probably get away with the smaller filter attached to the turbo, but I think it's less than Ideal. I'd rather a larger filter, honestly.

Calculator 1:

https://www.boosttown.com/forced_ind...calculator.php

I used the following variables:

Engine RPM: 6000
Engine Size: 1800
VE: 90 (I'm guessing as I couldn't find any info on the VE of the 2ZR N/A)
Boost: 0.55


Calculator 2:

https://www.widman.biz/English/Calculators/CFM.html

I used the following variables:

Engine Size (cc): 1800
RPM: 6000
VE:1.55 (drop down te VE menu and select, "Enter a specific value)
myfirstyotaToronto Canada · Apr 13, 2019#109
Looks like a battery relocate is on the horizon?
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 13, 2019#110
Originally Posted by myfirstyota ↑
Looks like a battery relocate is on the horizon?
Haha, I certainly hope not. There's actually lots of room in there for a good sized filter. After all the tweaks I'm having to do, I really don't want to tackle a custom intake, but I really think it's the best route in the long run.

I'll tell ya, I wish I'd been able to access some of this stuff before struggling with making this bloody turbo outlet coupler clear the subframe.

http://greenhulk.net/forums/showthread.php?t=127433
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 13, 2019#111
Turbo Re-clocking

In order to get clearance for the coupler coming off the turbo - it was hitting the subframe - I had to reclock the turbo a few degrees, aiming it a little more straight down. Of course, this put sideways strain on the wastegate actuator arm. This would not be good as it might not jam, but it might bind a bit - not something you want happening to your wastegate actuator.

I used my dremel tool to make the bolt holes in the actuator support bracket into slots.

Picture not included in this copy

I also made slight slots in the holes where the actuator mounts to the bracket as well as englaged the hole that the actuator arm goes through.

Picture not included in this copy

With the turbo re-clocked and the two above modifications, the actuator arm is once again at 90 degrees to the actuator and the wastegate arm. I also managed to gain 1/4" clearance between the couple and the subframe. Before the pipe was pressed against the subframe and deformed. I'm pretty sure there will be no issues as if the pipe makes contact with the subframe under load, it will just be pressing a bit on the flexible coupler and not rubbing per se. Once I attach the forward intercooler pipes, I can pull it a bit farther from the subframe. There is a bracket that attaches another rubber coupler a bit farther forward to one of the AC compressor bolts which will hold everything in place.

The coupler is touching the oil drain braided hose, but I'm not concerned as these two items move in unison. I'll put a little rubber tubing between the braided hose and turbo coupler for good measure.

Picture not included in this copy
stidnamAustralia · Apr 14, 2019#112
Just going back a page or two, the manifold looks like it places the turbo as close to the block as you could get. I'm wondering though if you had the option to make a manifold from scratch, could you have done so and maintained required clearances without the need to massage the firewall? And been able to still route the exhaust, intake and cooler piping? E.g. by moving the turbo to the left or up or down...
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 14, 2019#113
Originally Posted by stidnam ↑
Just going back a page or two, the manifold looks like it places the turbo as close to the block as you could get. I'm wondering though if you had the option to make a manifold from scratch, could you have done so and maintained required clearances without the need to massage the firewall? And been able to still route the exhaust, intake and cooler piping? E.g. by moving the turbo to the left or up or down...
I would say yes to a custom manifold and clearance providing there was room for the wastegate actuator as it is between the block and turbo. I wish the kit had come with the option of a T25 for two reasons: more clearance and faster spooling at lower rpms. I expect you could do anything with custom exhaust and charge/intake piping.

On another note, I'm considering picking up a different intercooler. Ebay has ones with lower ports that wouldn't require me to cut as much body metal. Plus, they have threaded fittings on the bottom and top as opposed to the brackets which would make install much easier. The ones I've been looking at are also 2" or 2.5" deep as opposed to the kit intercooler at 3". Frankly, this intercooler is going to be a bit of a PITA to install in the Yaris.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 14, 2019#114
The plot thickens

Before starting to go crazy with my grinder, I figured I'd better put the front on the car so I could actually see what space restrictions I'm dealing with. Well, I thought I would have more space near the foglights. As you can see in the picture below, There is just enough space for the pipe to go down through but the piping rubs on the corregated crumple zone and the foglight body. If I remove the crumple zone tabs, there will be adequate room. However, I'm not really enthusiastic about that, so my plan is to bend them upwards to the frame.

I will have to cut the piece of charge pipe that has the blowoff valve, just below where the blowoff valve mounts and then use some different angled couplers to make it mate with the intercooler outlet. I think a lot of this could be simplified with an intercooler that has the inlet and outlet at the bottom. I'm also coming up at a bit of a loss as to how to mount the intercooler. The brackets that come with the kit for the Corolla are useless in this project - but that's to be expected. I hope to make a decision about which intercooler I'll use but first want to check with the guys at turbokits.com to see if it will in any way affect the tune. I don't think it will, but I'm trying to keep the kit as close to the way it came as is possible.

There is one small upside to all of this though. The angle I have to put the blowoff valve pipe at necessitates a rotation of the MAF (intake to throttle body pipe) which now gives me more room between this pipe and the battery - a good 1.5" - 1.75". Bonus!

May plan is to use longer couplers and not push the pipes in too far. This should give me lots of flex in the system to accommodate engine torquing.

Pics of the tight space:

Picture not included in this copy

Picture not included in this copy
ern-dizCA all day · Apr 15, 2019#115
Big props for the excellent documentation 👏
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 15, 2019#116
Originally Posted by ern-diz ↑
Big props for the excellent documentation 👏
Thanks, ern-diz! I appreciate that. The documentating helps me maintain enthusiasm as I encounter one challenge after another. It also keeps me focused on what needs to be done next. I think there's something inherently wrong with me, in that I crave these projects even though they amount to one minor frustration after another. 😆
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 15, 2019#117
I have spoken with the guys at turbokits.com and a different intercooler would, as suspected, have no impact on the operation of the system, or the tune. So, I am ordering an intercooler and a series of pipes and couplers this evening. I'll post up some pics of the parts and an explanation of my plans. I'm also ordering a bunch of 3" piping, couplers, clamps etc to build a custom air intake for the turbo.

Here is a sketch of my intake setup. The main two upper pieces are 3" 90 degree elbows. The piece that attaches the filter to that is a 45 degree elbow. This piping runs behind the engine, then takes a 90 degree turn forward and goes under the rad hose and MAF pipe. The heater hose that attaches to the side of the block is being re-routed anyway as it's cut to supply the turbo for cooling. It will be tight but doable. It will need supports along the way. Fortunately, all of this is attached to the engine and therefor moves with the engine, so rubber padding to avoid chafing will need to be minimal. This places the filter right beside the headlight and down 4" - 6", where the OEM airbox used to sit. Sound be fun!

Pics. I may decide to use a 45 degree coupler and short piece of straight pipe where the filter attaches. The couplers do give a little extra flexibility. We'll see how it goes.

Picture not included in this copy

Parts

Picture not included in this copy

Here is the intercooler that I plan to buy. It should make installation much easier and give me more room and better mounting options. It is a tube and fin as opposed to a plate and fin, but, again, I'm running such low boost that heat shouldn't be any issue. With the cold air intake I'm planning, I could probably get away without an intercooler altogether, but I wanna play it safe. 😁

https://www.ebay.com/itm/Universal-F...w/263672225472

Picture not included in this copy

Or, this one, which gets good reviews for a budget intercooler on the tubro boards:

https://www.ebay.com/itm/EMUSA-unive...YAAOSwextZwI1Q

Picture not included in this copy

My homemade bead roller. I couldn't justify a couple hundred $$ on a Princess Auto bead roller as nice as that would be, so I stole an idea from the net. It took a lot of filing and grinding but it works well. It makes a pretty good bead on flat aluminum, so I hope it will work well on the piping too. Not looking for perfection and you won't see the beading anyway as they're hidden under couplers. I'll post up a pic of a bead after I fit and cut the various pipes.

Picture not included in this copy
myfirstyotaToronto Canada · Apr 15, 2019#118
Its the learning process you crave. Much like many of us, I bet its the challenge you enjoy.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 15, 2019#119
Originally Posted by myfirstyota ↑
Its the learning process you crave. Much like many of us, I bet its the challenge you enjoy.
For sure, myfirstyota. I have to constantly fight the urge to rush things/take shortcuts. That said, a lot of aspects of the project are compromises.

I was out investigating how the heater hoses will play with my planned intake. It looks as though it will work with the trickiest part being getting the 3" piping down between the block side heater port and rad hose. I may need to splice in a coupler there for flexibility. Since I'm having to cut the heater hoses to attach to the turbo, I can then rotate the cut pipe ends out of the way. I'll also need to shave about 3/8" off the plastic battery tray. Interestingly, I had an old R134 A/C refrigerant can lying around and it's precisely 3" in diameter. I used it to test clearance for the 3" intake pipes. Worked like a charm. There is one cast tab on the head at the back of the motor that will need to be ground down slightly, as well as the removal of a steel bracket that I think was used for a harness support. I'll also have to slightly bend the transmission dipstick tube and overflow tube a bit out of the way. Other than that, it looks like a reasonably clear path.
tmontagueCaledonia Ont. · Apr 15, 2019#120
i love this thread. great progress made and that home made bead roller is something else. How did you manage to make that?
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 15, 2019#121
Originally Posted by tmontague ↑
i love this thread. great progress made and that home made bead roller is something else. How did you manage to make that?
Thanks Trevor! It's short piece of 1/4 steel rod welded onto the top jaw. This I had done by our shop teacher as I don't weld. I had to curve the 1/4" rod with a flat file as obviously I'm beading round pipe. I then used a pneumatic grinder and roughed out the cup in the bottom jaw and finished with a rat tail file. It's far from perfect but seems to work great.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 15, 2019#122
Planned 3" Intake Routing

This will be a touchy project, but I'm confident it can be done.

Explanations are in the pics...

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 16, 2019#123
Downpipe Installed

Another job during which I wish I had 3 - 4 hands. The holes in the downpipe flange are large - for a good reason - to allow for lots of play when fitting the pipe (necessary). This makes it want to bounce around a lot while installing. It also allows for an improper alignment if you're not careful. I had to support the pipe on the crossmember to maintain the approximate 1" - 1.5" vertical clearance while at the same time trying not to mess up my high temp copper rtv that is on both sides of the metal flange gasket. The nuts that attach the downpipe to the turbo (same type that attach the turbo to the manifold) are soft copper which is great as they bite well and shouldn't back off with the included Belleville washers installed under the nuts.


Picture not included in this copy

Man, this baby should flow! The Corolla obviously has its post-cat 02 sensor entering from the passenger side as opposed to the Yaris, from the driver's side. However, I'll be installing a cat, so a large section of the beautiful 3" stainless steel after the braided flex joint will have to go. 😢 I'll have a bung welded into the pipe after the cat. I may need to extend the wire on the sensor and attach it somewhere in the tunnel. I haven't reinstalled the heat shield yet, but will as there is lots of room to get back under the downpipe. It's an absolutely lovely downpipe btw.

I looked like a dude from a Brylcreem ad from all the goey undercoating under my car. Ewww... 😆

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 17, 2019#124
Turbo Coolant Hoses

Only had an hour and bit tonight but got a small job done.

Fortunately the hoses were molded in a way that I could cut them up and use them. Thankfully turbokits allowed enough steel braided coolant hose length to attach to the car's heater lines from any angle.

Picture not included in this copy

Cleared up a large amount of space. The 3" intake piping should fit easily now down and through to the stock airbox area for filter placement. I removed the battery and trimmed back the tray; allowing myself an additional 3/8" - 1/2" space. The only challenge left here is that the heater hose that goes into the firewall will be almost touching the 3" piping. If the engine rocks back, it may pinch the hose a bit. But, the 3" 90 piping I ordered has a very gradual curve (I guess mainly for smooth air flow), but the radius may work out perfectly; leaving space for the heater hose at the firewall. Fingers crossed. If that fails, I'll figure out a way to solder on a 90 fitting on the firewall heater hose connection.

I'm hoping that with all this additional plumbing, I won't have difficulty priming the cooling system.

Picture not included in this copy

A shot from below. I'll use a good heat resistant zip tie or something else to secure these two hoses together where they cross eachother. Other than that, the turbo braided hoseing is rigid enough that it is not touching any part of the car or engine...bonus.

Picture not included in this copy

Tomorrow, time permitting, I'm going to prime the turbo with oil and hook up the oil supply line.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 19, 2019#126
Turbo Oil Supply Line

This job had its moments. It all came together though. I'll know for sure later when I look for leaks.

Removing Oil Sensor

Picture not included in this copy

Parts going together. I used some teflon tape on some parts and rtv on others.

Picture not included in this copy

Installing the fittings requires retapping the sensor port hole. I think it's just to clean the threads in preparation for the brass fitting. I used a well greased 1/8" NPT tap, but still managed to create some filings. This worried me as it's a direct shot from there - passing through no filtering, I think, to the turbo. Although the grease retained most of the filings, there were some in the block. So, I diligently flushed it many times with brake cleaner and wiped out with a microfiber to towel, then rinsed again. There's no evidence of any filings, so I should be good.

Grease covered tap.

Picture not included in this copy

Tapping

Picture not included in this copy

Fittings installed

Picture not included in this copy

Line attached. I'm going to do a flow test soon. The engine will not start, but I'll look for evidence of oil coming from the turbo end of the supply line after I prime the turbo with oil. Hopefully, starter speed will provide enough pressure to flow oil up and through the line.

Picture not included in this copy

After the test, I'll hook up the end to the turbo. Routing the supply line up to the turbo is going to be a bit of a challenge, involving good heat resistant zip ties. The supply line is very long, presumeably to allow keeping it far from hot parts such as the manifold and turbo compressor.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 22, 2019#127
A Slow Weekend...

Didn't get much done due to being away visiting family. A couple things project-related did happen though.

I fixed an issue I had with the oil return line. It had a very, very slight uphill curve going into the oil pan. I reclocked the center section of the turbo, cut 1/2" off the pipe and reinstalled. The front of the car is higher on the jackstands than the back, so once the car is lowered, I should have a very good downhill run to the pan. However, I'm going to temporarily replace the steel braided hose with clear braided hose of the precise length and test the oil drain with the car still nose-high. I imagine I'll be in boost on a few long hills from time to time. As a positive spinnoff of clocking the center section of the turbo, my coolant lines are now a wee bit father away from the downpipe. I have about 1.5" - 2" clearance. I'll wrap those in the aluminum tape that came with the kit. I should be fine heatwise as I've read online about people with lines closer to the downpipe who have had no issues.

I also addressed the clearance issue between the first charge pipe and the subframe. This I did by shortening both legs of the coupler, allowing the aluminum pipe to go up farther into the engine bay. Although I've read the install manual myriad times, somehow I missed the trimming of the 45 coupler (RTFM, more carefully, silly boy, lol). I now have about 1/2" clearance where before I had slightly less than 1/4". Since I still haven't tightened up my dogbone mount, I rocked the engine back and forth and the piping doesn't contact the subframe. Yay! I had a few inches of turbo to wastegate hose left (after clocking the turbo way back when, I had to shorten this hose) and it worked perfectly as a contact pad between the charge pipe and engine casting rib. I degreased the rib and hose and glued it on with a bit of RTV. Worked great! I'm going to use a bunch of this around the car for all potential contact areas between the turbo piping and body/frame etc.

Picture not included in this copy

In other news, most of the stuff for my custom intake has arrived to my US destination. I hope to start to work on that about mid week. I may get the urge to hook up the stock airbox and start the car, but I'll try to wait until my intake is finished.

Lastly, I'm going to ask the turbokits guys if I can get a shorter oil feed line. The one with the kit is quite long. I need one less than 1/2 the length of what came with the kit. There's probably a lot more space in the Corolla to route that around than there is in the Yaris.
CrankyOldManWest Michigan · Apr 22, 2019#128
Awesome news! Super stoked to see this happening!
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 22, 2019#129
Originally Posted by CrankyOldMan ↑
Awesome news! Super stoked to see this happening!
Yup, getting exciting. Looking forward to working on my intake this week.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 23, 2019#130
No pics tonight, but I completed some modifications to the heater hoses to provide more clearance for my rather large intake pipe setup. There are a bunch of old engines in our shop that the kids are dismantling and putting back together. They will never be put in cars, so I scavenged a couple of 5/8" heather hoses with tight elbows, cut them up and replaced portions of my stock hoses. This gives me more room at the firewall to run my 3" piping. It also allowed me to gain more clearance as the coolant lines for the turbo loop under the down pipe. I have a bit more length to secure the hoses with either high heat zipties of metal zipties.

Really hoping this weekend to top up with fluids and crank the car over without starting and observing the oil flow back to the pan via the temporary clear braided hose. If all looks well. I'll attach the oem airbox and run the car a bit. Should be nice and loud - painfully, I bet - with that massive 3" downpipe. After I determine that there are no leaks, or if there are, fix them, I'll set to work on the intercooler piping. Then will come the injectors and F/IC wiring.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 24, 2019#131
Intake and new intercooler

Here is a pic of the custom 3" intake. Not too bad for just under $80.00 for the piping, couplers, clamps and filter. The right section which is lying flat will rotate upwards about 45 degrees and if everything goes as planned, the filter will land right where the oem airbox once resided. This intake should flow really well. The true test will be tomorrow when I actually go to install it. I will have to cut about 5"-6" off the left curved pipe which is great as it will serve two purposes: 1) it will place the coupler away from the heat of the manifold and turbine and 2) it will give me the few inches of pipe I need to attach the filter. Right now, the filter is just resting there and not attached. The section of the intake running between the two elbows will be wrapped in reflective heat tape.

Also in the pic is the new intercooler. $60.00 for what seems like a very solid and sturdy EMUSA intercooler doesn't press the budget too much. The intercooler, which comes easily modified mounting brackets should really simplify the the plumbing at the front of the car. The other two coupers (2.5" 90 and 45) are to assist in mounting the intercooler.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 26, 2019#132
Intake Modding and Test Fitting

As suspected, this is a lot of work. I worked on clearing the path. First, by removing a couple little nubs protruding from the head that were in the path of the piping. There is only a pic of one that I removed. This one was removed with my 4" angle grinder. The other I had to use my recip saw with a metal cutting blade.

Picture not included in this copy

Picture not included in this copy

Despite bending the A/C tubes, I only had about 1/4" between the intake piping and A/C lines. I shaped the intake pipe with BFH, covered by a cloth. The dent is fairly smooth and shouldn't affect airflow. There is a solid 1" - 1.5" clearance now. I'm still going to figure out a way to bend the short straight section of A/C line a bit although I'm pretty sure I already have enough clearance.

Picture not included in this copy

Picture not included in this copy

Cutting the piping was messy as I used my angle grinder with cutting disk. I spent a lot of time deburring.

Picture not included in this copy

Unfortuntely, no pics of the bead rolling. I still have a section to do and will post pics of that next time. This pipe is very heavy gauge and my hands are pretty stiff now after bead rolling only 2 pieces of piping.

Test-fitting of parts. To address where the pipe might make contact with the head bolt flanges, I'll either slide a piece of coupler on the pipe where it might abrade the piping. Or, I'll figure out some form of clamping device, metal strapping on rubber that could surround the pipe and bolt to the head. Or, both.

Picture not included in this copy

Picture not included in this copy

Unfortunately, the section of pipe that I had to remove from the elbows was a bit short and the base of the filter is contacting the transmission and dipstick tube. I need a piece about 3"-4" longer. The filter will be pushed out that distance from where is is in the pic.

Picture not included in this copy

As the engine bay gets more crowded, I'm starting to worry about airflow around the engine and turbo. As much as I hate the thought of it, I may ultimately have to install vents or a reverse hood scoop. I could also mount a low profile, thermostatically-controlled fan under the hood scoop. I guess I'll know when I start driving and at the tuner's if there will be an issue. I ordered a bunch of fiberglass reflective tubing for my water lines and oil supply line, though these are all a decent distance from the manifold, turbine and downpipe. Also considering a turbo blanket. The entire section of the intake that goes along the back of the engine will be covered in reflective fiberglass tape. I'll likely wrap the downpipe too.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 27, 2019#133
Today's progress

I had to 'mould' the intake piping more, especially by the right side of the engine. I was worried about the piping chafing on the upper valve cover bolts. I have acceptable clearance everywhere now and the pipe has been wrapped with the fiberglass reflective tape. All I have do now is make something to rigidly hold the piping in the center, where the coupler is to the back of the valve cover. I liked the look of the aluminum piping better before being wrapped, but it will all be hidden anyway.

Picture not included in this copy

New intercooler mounted. The hardware worked perfectly for attaching the intercooler to the bottom lip of the lower front frame. Funny thing is that they only sent 2 bolts and washers, but the intercooler has threaded posts for both top and bottom. Maybe it's only supposed to be attached either top or bottom and the couplers do the rest of the holding, allowing it to move a bit.

Picture not included in this copy

A little bump stop. There is about 3/4 of an inch between the intercooler and crash bar, but I figured I'd play it safe. More of that great turbo wastegate hose attached with RTV.

Picture not included in this copy

Piping connected. I still make contact with the foglight, but just have a few spots to bend over and grind away. I should have lots of clearance after I do that.

Picture not included in this copy
tmontagueCaledonia Ont. · Apr 27, 2019#134
Looking good man, keep it up!
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 27, 2019#135
Originally Posted by tmontague ↑
Looking good man, keep it up!
Thanks, Trevor. I appreciate it. It's a fun project.

A question for ya... You put a sandwich plate in after you upgraded to the screw-on filter mount, correct? Did you install an oil cooler?
tmontagueCaledonia Ont. · Apr 27, 2019#136
Originally Posted by 06YarisRS ↑
Thanks, Trevor. I appreciate it. It's a fun project.

A question for ya... You put a sandwich plate in after you upgraded to the screw-on filter mount, correct? Did you install an oil cooler?
correct, this was the primary reason for my screw on filter mount upgrade.

I did not install a cooler however, there should be enough space in that area for oil lines you will just have to figure out a way to strap the lines secure as they run out to the cooler. They will technically run alongside the bottom end of the block.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 28, 2019#137
Originally Posted by tmontague ↑
correct, this was the primary reason for my screw on filter mount upgrade.

I did not install a cooler however, there should be enough space in that area for oil lines you will just have to figure out a way to strap the lines secure as they run out to the cooler. They will technically run alongside the bottom end of the block.
Thanks. I had read that many of the sandwich plates would not fit due to proximity to the block, but obviously that's not true. There must be narrow ones available that have a small enough diameter to fit. Secondly, I'm thinking it might be a good idea to have an oil cooler, or minimally, at least initially, monitor oil temps. I was speaking to one of my son's hockey teammate's fathers who has built a number of performance cars, and he said that, in no uncertain terms, I should have an oil cooler. I hadn't mentioned to him that the turbo is water cooled, so that should make a difference. A cooler would also provide a little addditional oil in the system to aid in cooling.

How are you monitoring oil temps? Did you put a sensor in your sandwich plate? Unfortunately, Torque doesn't have access to that PID.

I am definitely installing a transmission cooler, but am on the fence about an oil cooler at this point.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 28, 2019#138
Piping Frame Mods

The right side piping now fits fine with about 3/8" - 1/2" clearance between body parts and charge piping at all locations. I'm still going to install rubber tubing at all locations with sharp edges. I'll pick up 4' - 5' of the smallest diameter rubber fuel line, cut and glue that with RTV to all potential wear areas. All that remains to do now at this corner of the car is to degrease, lightly sand, prime, paint and oil spray all the metal bits that I cut and bent. I'll install the BOV and clamps after washing all of the piping inside and out with soapy water and degreaser.

Area to be dealt with.

Picture not included in this copy

Slotting crumple zone tabs

Picture not included in this copy

Tabs pounded up

Picture not included in this copy

Large flange slots cutting

Picture not included in this copy

Good clearance

Picture not included in this copy

Fitting finished. Just need to trim up that right side intercooler coupler.

Picture not included in this copy

Picture not included in this copy


Update - Painted Frame Modifications

Picture not included in this copy

Rough placement of the transmission cooler. Will be picking up some hose this week and will run the cooler on the transmission return line, when I figure out which line it is.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 28, 2019#139
A Possible Breakthrough!

I had been pondering where to place my transmission cooler. I wasn't keen on stacking another cooling device in front of the radiator. I've also been concerned about my crowded engine bay and the potential of overheating.

There is a plastic shroud/cover that goes from the radiator over to the pasenger side. It covers a large opening behind which sits the A/C compressor. This opening is probably 1/3 of the width of the engine bay. If I place my transmission cooler in that area (it basically fills it with about a 1" space around the perimeter), I will accomplish a few things:

1) A much larger opening for cool air to enter the engine bay
2) No restriction to the radiator, better flow through it.
3) No heat transfer between the transmission cooler/rad and vvsa

I just have to make a mounting system for it. I have to do some reading on transmission cooler orientation. The way I propose, the tubes are vertical and I don't know if that would create an issue pumping the transmission fluid. I don't expect there would be an issue as it's very free flowing, but the fluid would be fighting gravity, but then again gravity would be helping on the downward runs. 🤷

EDIT: According to Derale, the coolers can be mounted vertically or horizontally.

Picture not included in this copy
MaritimeWoodstock nb · Apr 28, 2019#140
Nice. Looks like it was made to go there

Sent from my moto e5 play using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 28, 2019#141
Originally Posted by Maritime ↑
Nice. Looks like it was made to go there

Sent from my moto e5 play using Tapatalk
Haha, thanks. If I didn't have this one already, I would buy a plate and fin unit. However, this one should provide a lot of cooling as it's made for a mid-sized truck - half ton, I assume.
tmontagueCaledonia Ont. · Apr 28, 2019#142
Pro tip: transmission line that enters the trans high up tends to be the return line. The line that attaches low on the trans housing tends to be the feed line.

I went with that when flushing the trans fluid on my wife's Vibe and saved me quite a mess.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 28, 2019#143
Originally Posted by tmontague ↑
Pro tip: transmission line that enters the trans high up tends to be the return line. The line that attaches low on the trans housing tends to be the feed line.

I went with that when flushing the trans fluid on my wife's Vibe and saved me quite a mess.
Good to know. Thanks much! Any idea how much pressure a typical A/T cooling circuit has?
tmontagueCaledonia Ont. · Apr 28, 2019#144
Originally Posted by 06YarisRS ↑
Good to know. Thanks much! Any idea how much pressure a typical A/T cooling circuit has?
No idea, but I cannot he nearly as much as a braking system, steering system etc based off of the fitting and hose clamp styles that are used
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 29, 2019#145
Originally Posted by tmontague ↑
Pro tip: transmission line that enters the trans high up tends to be the return line. The line that attaches low on the trans housing tends to be the feed line.

I went with that when flushing the trans fluid on my wife's Vibe and saved me quite a mess.
This confirms your explanation. I found this in my U340E Transmission service manual. Now, I am assuming "Inlet" and "Outlet" refer to the direction of fluid flow relative to the engine and not the cooler.

Picture not included in this copy

Hoping to source some of these locally. I figure there's no reason I can't just put these through the upper loops of the trans cooler to support the top. I'll figure something else to secure the bottom.

Picture not included in this copy
ern-dizCA all day · Apr 29, 2019#146
This is coming along so much faster than I expected. An absolute joy to follow.
tmontagueCaledonia Ont. · Apr 30, 2019#147
Originally Posted by 06YarisRS ↑
This confirms your explanation. I found this in my U340E Transmission service manual. Now, I am assuming "Inlet" and "Outlet" refer to the direction of fluid flow relative to the engine and not the cooler.

Picture not included in this copy

Hoping to source some of these locally. I figure there's no reason I can't just put these through the upper loops of the trans cooler to support the top. I'll figure something else to secure the bottom.

Picture not included in this copy
yep, that diagram confirms it, lower hose is from pump, upper is drain hose back to trans.

Those hose clamps are readily available from Princess auto for a decent price. I used 3/8" ones for my main 4gauge power line for my batter relocation and they worked very well. Not sure if a Princess Auto is close to you but they do ship from their online store
myfirstyotaToronto Canada · Apr 30, 2019#148
Home depot may have them in their catv installation section. Not sure if princess is in NB as Trevor stated.
06YarisRSThread starterFredericton, New Brunswick, Canada · Apr 30, 2019#149
Thanks gents. The local store had a pack of 15 1/2" ones for $6.00 and change. They work absolutely prefectly for planned installation. I tested it on the cooler and it holds it nice and tight on the tube radius when screwed down. I'll also use them for my 3/8 transmission cooler lines to keep everything nice and secure. More on this in my next post.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 1, 2019#150
Pipe Clamps

The cramped space of the engine bay made this a really tough job. The coupler on the turbo compressor simply would not go on with the clamp even though I loosened the nut to the last thread. I had to grind down the collar on the clamp, and install it after the pipe was on. The clamp install on the 3" intake was marginally easier. I used a standard worm clamp on the intake as there's no pressure in that, and I used T clamps everywhere else.

Picture not included in this copy

I have to significantly modify the right side intercooler pipe as it wants to be higher up due to the original intercooler. I think shortening one end and taking a couple inches out of the center and a short 2" coupler should do the trick.

Picture not included in this copy

Picture not included in this copy

A couple more clamp pics...

The intercooler looks damaged, but it's the reflection of the light. It's not nearly as bad as it looks and I'll straighten the fins out with the tip of my utility knife.

Picture not included in this copy

Picture not included in this copy

I had my '08 at school today and used the vernier calipers to confirm my suspicion that the trans cooler lines are 8mm (5/16"). I have found fittings and I'll use a 5/16" compression to 3/8 rubber barb fitting to and from the cooler.
I spoke with a transmission shop today and all fears about fluid restriction have been allayed. Also, running the cooler vertically will make no difference, apparently.

Picture not included in this copy