Yarisworld Archive

2ZR Turbo Yaris

561 posts · 343,257 views · page 6 of 12

Replies continued

06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 24, 2019#251
Originally Posted by Maritime ↑
Nice work as always. so close to the day it is fully set free to roar down the road.
Thanks! Yup, getting close. Getting excited for sure. 👏
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 24, 2019#252
Gauge Pod Test Fit

A bit of a spoiler. I won't have pics until tomorrow, but, the good news is... the pillar is a great fit. Is it 100% perfect? No, but it's very acceptable. The contours are very good and the fit should be fairly seamless. I will need to figure out a method of attachment as there are no pins. I think I'll use long screws, drill a couple holes in the steel pillar and pull the gauge pod cover tight. The way it's designed, I can hide the screws really well just under the top and bottom pod holes. The screws will be invisible from the driver's and passenger's positions. I plan to spray the pillar with a flat or satin clear coat. Right now, although the color is a close match, the pod is way too shiny, whereas the dash has more of a matte finish.

Pics tomorrow, I promise. 😁
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 25, 2019#253
Gauge mounting...turning point

I am heavily leaning toward not using the A-pillar gauge pod. One things I've always appreciated about the Yaris is it excellent visibility from the driver's seat. The gauge pod would look amazing in the car, without a doubt, but I just can't spare any visibility. It is not overly intrusive, but I could see the larger blind spot potentially causing a problem. I also like to drive with my seat all the way back. If I push the seat forward, visibility is fine. Again, a compromise I don't think I'm willing to make at this point. It's a bit of a shame, because with a few mods to the pillar and a little matte clear on it, it would look pretty darn good. For a cheap attempt at a gauge pod, they did a pretty good job fitment-wise.

So, some pics:

Pod test fit in my '08...

Picture not included in this copy

My alternative plan. I just spent a couple of hours shaping the gauge 'adapters' to fit the curve of the glove box. This was tedious and it turned out pretty good, but not perfect. I plan to drill 3 holes a bit smaller than the gauges and then use some kind of small saw or my dremel and sanding disk to round out he holes to size. I plan to do this on the car as I don't feel like taking the entire dashboard off. I happen to have have a spare dash - the one that originally came with my '06, so I used its driver's side glove box to shape the gauge adapters. I'll epoxy the gauge adapters to the dash from the inside.

Opinions sought... I can either line the gauges up in a straight row of follow the curve of the steering column bezel. The problem with the latter is that the gauge face angles would be off. so, it's probably best to keep them in a straight line.

Gauges in line:

Picture not included in this copy

Gauges following steering column bezel (well, sort of):

Picture not included in this copy


Other pics:

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 25, 2019#254
A bit of progress on the gauges this evening...

I actually tired the gauges flush and liked it better, except that they don't sit level and you can notice this from different angles. I think I'll paint the gauge trim rings black. The silver is a bit stark and black would go better with the interior. The gauges have film over the glass (plastic?) and I'll remove them when they are all installed. Once nice thing I discovered is if I modify the hardware, I won't have to epoxy the gauge adapters to the glove box.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

All three gauges in, but not wired yet

I decided to follow the contour of the streering column cover and I'm glad I did. For one, it looks better and visibillity of all gauges is perfect from my seating position. I think they look great, but if the silver rings are easy to get off, I might paint them black.

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 26, 2019#255
F/IC Mounting and Wiring Started

I mounted the F/IC flat on the plastic tray behind the glove box by laying down a couple foam strips (used on old 6" compounding pad), drilled holes and ziptied it in. It's solidly mounted and no rattles.

Picture not included in this copy

Started wiring the F/IC. I just had a bit of time, so only got done the crankshaft sensor/F/IC/ECU connections. I hope to have all the wiring done in the next day or two. I'm now off for the summer, but have two kiddies to watch, so time is a bit limited.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 27, 2019#256
F/IC fuel injectors wired

Well, three of them anyway. It looks messy now, but it will be all tidied up, taped and tucked back into the plastic ECU wire retaining clip.

Picture not included in this copy
ern-dizCA all day · Jun 27, 2019#257
This is the part you've been somewhat dreading, eh?
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 27, 2019#258
Originally Posted by ern-diz ↑
This is the part you've been somewhat dreading, eh?
It is somewhat, ern-diz. I'll be cringing as I reconnect the negative battery terminal. Lol. I could never get a definitive commitment from anyone that my wiring diagrams are correct. I am hoping that if there are no sparks and a no start scenario, that the ECU will at least set a code to point me in the right direction.

I finished the fuel injectors, power ground and the MAF wiring. Just TPS, signal ground and 12V power left to connect. Hoping for a start tomorrow. Wish me luck lol!
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 27, 2019#259
Current state of wiring

So far I have hooked up: injectors, MAF, crank, +12V power, and 2 grounds. I am at a standstill until I figure out where to find a signal ground, as I can't figure it out from the diagrams. I'm also struggling with the the TPS+ connection.

Here is a pic of the current state. The wire in loom running across the top is the +12V switched power source which comes from the smaller ECU connector. The bunch of wires to the left will all bundle up nicely and fit into the ECU plastic connector cover. Everything will be enclosed in a large piece of conduit and taped really well. It should look completely factory when I'm done.

I have only 4 wires remaining to be hooked up: TPS+, 021+, 022+ and signal ground.

Picture not included in this copy

Next post will be an appeal for help from anyone familiar with Toyota wiring diagrams. I have an email in to AEM, but they don't want to make specific connection suggestions. I'll try the turbokits guys, and then maybe seek out an automotive wiring forum.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 27, 2019#260
Seeking wiring suggestions

As mentioned, I'm struggling with the last few wires for the F/IC install. I can't find anything online that shows a specific Toyota signal ground symbol. I'm also not sure which wire from the ECU to hook to the F/IC TPS+ wire. Please see diagrams below and if you know the answer(s), please shout them out. 👏

Grounds?

Picture not included in this copy

Here is one of the pics/questions I sent to AEM.

Picture not included in this copy


EDIT: I found this site which leads me to believe that I should use the Yellow VTA wire. I'm open to interpretations.

http://www.tsienna.net/throttle_peda...quot_-542.html
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 28, 2019#261
Temp guages bench test

I'm liking these gauges, though I wonder how long they will last. I'll be replacing much of the wire with true 18 AWG and soldering and heat shrinking all connections. Wire will all run through taped up conduit and attached along its length with zipties.

The gauges look much, much better in person than these pics depict. The colors are much brighter and deeper in person. Should look amazing in the car. The blue color is triggered by the headlight switch, so they run blue at night and white during the day.

As for accuracy, the two gauges climb at very slightly different rates but usually stop at the same position. I used two candy thermometers - which were close to each other, but not perfect. I averaged the candy thermometer readings and used that to compare to the gauges and the readings were very close. My best guess would be 3 - 4 degress different than the candy thermometer average. Not a scientific approach, but the best I can do given what I have. I'd like to test the oil pressure gauge, but that would take to much frigging to connect to my compressor to test that.

Kudos to Prosport for at least having consistency in their gauges and sensors. I had a couple Autometer (mid range quality) temp dial gauges years back and they were off quite a bit more from each other than these gauges are.

Picture not included in this copy

Picture not included in this copy
CrankyOldManWest Michigan · Jun 28, 2019#262
TPS usually means Throttle Position Sensor. In a mechanically connected throttle, there is a rheostat (dimmer) connected to the shaft of the throttle valve so that other systems know what position the valve is in. In drive-by-wire systems (which almost all modern vehicles are) the position is sent by a Hall-effect sensor, not a rheostat. I'm having a hard time finding if the AEM can use that as an input.

Here's a simple diagram from a Corolla repair manual that uses a rheostat: http://www.tcorolla.net/circuit_description-558.html

Here's a very detailed technical report that discusses the connector and what the wires are on the 2ZR (or equivalent) ECU: https://web.archive.org/web/20140727...rticle_id=3597

Here's a technical writeup from an unintended acceleration investigation that uses different naming conventions: http://www.safetyresearch.net/Librar...port022110.pdf

Bottom line is, I don't know how to connect a Hall-effect sensor to an AEM EMS. My google-fu isn't turning up any obvious answers either. Hrm.
CrankyOldManWest Michigan · Jun 28, 2019#263
Looking at the link you posted, the 0-5V signals should be your TPS. VTA1 is the one that you want (VTA2 will be offset by a certain amount and will likely cause problems).
CrankyOldManWest Michigan · Jun 28, 2019#264
For posterity, here's what the pins are:
  • M+ / M- are the servo control signals. It's the same thing that you use on RC vehicle servos--Pulse Width Modulation (PWM)--to command the servo to a specific position. It's shielded to prevent electrical interference with the signal.
  • VCTA is the DC power supply to the circuit
  • ETA is the DC ground/common
  • VTA1 is the throttle position feedback, 0-5 VDC. 0 is closed, 5 is WOT.
  • VTA2 is the monitor signal for VTA1, which allows the ECU to detect a failed or faulty signal from VTA.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 28, 2019#265
Sam. Thank you!!!! You are de man!

I'll have a read of what you linked.

I have a very big favour to ask if you're up for it. Could you endeavour to answer two questions for me if I were to send you my engine control wiring diagram?


1) I have attached the F/IC "switched 12V power to pin 1 (+B2) in ECU small connector A21. This traces back to the EFI relay. This is what I was advised to do, but no explicit directions were given other than take it off the EFI relay. Is this in fact a switched power source, or is this black wire always hot?

2) Does the triangle symbol leading to what looks like earth ground in the Toyota wiring diagrams mean it's a "signal ground"?

Thanks!

EDIT: In re-reading your post, I see that ETA is DC ground common. Is this a signal ground and could I attach the F/IC signal ground to ETA (Pin 91 on C19)? Also, above I reference (+B2) in connector C19, I meant connector A21.

Edit 2: I'll be speaking to my tuner today and asking him of I need the TPS hooked up at all as it may be that the car's ECU can handle that and the F/IC doesn't need to be involved.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 28, 2019#266
Plug Gapping

The plugs need to be gapped down from .044" to .028".

Removing coil packs

Picture not included in this copy

Removing plugs

Picture not included in this copy

Gapping plugs

Picture not included in this copy

Torquing to 20nm (177 in/lbs, 14.75 ft/lbs)

Picture not included in this copy
CrankyOldManWest Michigan · Jun 28, 2019#267
I'll have to pull up the full EWD before I can solidly comment on the switched DC power, but that sounds reasonable.

Short answer, yes the triangle is ground.

Long answer is more complicated. You don't have to read this stuff, just some general theory and why there are different symbols.

The term "ground" is rather loose and fluid and causes no end of confusion--even to myself. The "E" in all of those connections probably refers to "earth", i.e. the planet, which is the standard zero reference for most voltage measurements. But in the case of your car, it's too insulated by the tires to be able to use that, so instead we use the negative terminal of the battery as zero. Connections direct to the Earth normally use the three shrinking lines. A local ground reference or "common" connection normally uses the downward triangle to differentiate it and in some cases may not be connected to the earth ground. There's also a "chassis" ground symbol that looks like a 3-tined rake. They are frequently used arbitrarily or will have different meanings in different international standards, leading to lots of confusion if you don't understand what the original intent was or what standard (if any!) it was drawn to.

If you get really technical, everything that conducts electricity has some resistance--even gold plated contacts and super pure copper wires. Good old Ohm figured out the relationship between resistance, voltage and current and his Law tells us that there is a voltage difference between any two points in a circuit that have resistance between them and a current flowing from one to the other. Generally speaking, anything connected directly to the battery with zero resistance is also at zero volts. Ideally you would be able to directly connect all of the ground wires to the battery terminal in a "star" configuration to minimize any voltage offsets. You can see in some wiring diagrams that multiple wires converge at a connection to ground, which is normally on the chassis. The wires and chassis all have some (very small) resistance in them, which creates a (very small) voltage difference between the ends of the wires or between the attachment point of the local ground and the nearest big wire on the negative terminal. That small bit of offset usually doesn't impact anything because it's effectively zero. If you have to take a very accurate measurement on that circuit, you should measure from the local ground point, not the battery. In the case of electrical signals or data communication, you need that reference point to be consistent and electrically "quiet". If you use a ground node near your injectors or the voltage regulator on your alternator you can inject lots of unwanted spikes or noise into your ground reference, messing up the relative voltage between that point and the supply/battery.

So the trick here is that you want as many of the ground references for the AEM and ECU to be as close as possible to minimize noise or offsets. In other words, choose wisely where you connect those wires.

Case in point: my horn doesn't work. The horn switch is fine, the relay is fine, the fuse isn't blown, and there's 12V at the positive terminal when the horn is pressed. It doesn't work because there is too much resistance or poor continuity between the horn's internal ground connection and the chassis. There's corrosion on the bolt threads between the horn and the battery as a result of taking the front bumper apart a few times and living in a state that salts their roads. My next step in fixing it will be to run a new ground wire from the nearest ground point to the horn itself and bypass the bad connections in between. If that doesn't work then I will run it to the battery directly. There's no risk of it causing a dangerous short though because the battery is on the other side of the relay contacts and there's a 10A fuse in that circuit as well. Some cars use the opposite method and put the horn on the battery side of the circuit and connect it to ground with the relay. That means the horn input is always "hot" and has the potential for a short to ground before the contacts, resulting in a horn that won't stop honking unless you pull the fuse or relay.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 28, 2019#268
Originally Posted by CrankyOldMan ↑
I'll have to pull up the full EWD before I can solidly comment on the switched DC power, but that sounds reasonable.

Short answer, yes the triangle is ground.

Long answer is more complicated. You don't have to read this stuff, just some general theory and why there are different symbols.

The term "ground" is rather loose and fluid and causes no end of confusion--even to myself. The "E" in all of those connections probably refers to "earth", i.e. the planet, which is the standard zero reference for most voltage measurements. But in the case of your car, it's too insulated by the tires to be able to use that, so instead we use the negative terminal of the battery as zero. Connections direct to the Earth normally use the three shrinking lines. A local ground reference or "common" connection normally uses the downward triangle to differentiate it and in some cases may not be connected to the earth ground. There's also a "chassis" ground symbol that looks like a 3-tined rake. They are frequently used arbitrarily or will have different meanings in different international standards, leading to lots of confusion if you don't understand what the original intent was or what standard (if any!) it was drawn to.

If you get really technical, everything that conducts electricity has some resistance--even gold plated contacts and super pure copper wires. Good old Ohm figured out the relationship between resistance, voltage and current and his Law tells us that there is a voltage difference between any two points in a circuit that have resistance between them and a current flowing from one to the other. Generally speaking, anything connected directly to the battery with zero resistance is also at zero volts. Ideally you would be able to directly connect all of the ground wires to the battery terminal in a "star" configuration to minimize any voltage offsets. You can see in some wiring diagrams that multiple wires converge at a connection to ground, which is normally on the chassis. The wires and chassis all have some (very small) resistance in them, which creates a (very small) voltage difference between the ends of the wires or between the attachment point of the local ground and the nearest big wire on the negative terminal. That small bit of offset usually doesn't impact anything because it's effectively zero. If you have to take a very accurate measurement on that circuit, you should measure from the local ground point, not the battery. In the case of electrical signals or data communication, you need that reference point to be consistent and electrically "quiet". If you use a ground node near your injectors or the voltage regulator on your alternator you can inject lots of unwanted spikes or noise into your ground reference, messing up the relative voltage between that point and the supply/battery.

So the trick here is that you want as many of the ground references for the AEM and ECU to be as close as possible to minimize noise or offsets. In other words, choose wisely where you connect those wires.

Case in point: my horn doesn't work. The horn switch is fine, the relay is fine, the fuse isn't blown, and there's 12V at the positive terminal when the horn is pressed. It doesn't work because there is too much resistance or poor continuity between the horn's internal ground connection and the chassis. There's corrosion on the bolt threads between the horn and the battery as a result of taking the front bumper apart a few times and living in a state that salts their roads. My next step in fixing it will be to run a new ground wire from the nearest ground point to the horn itself and bypass the bad connections in between. If that doesn't work then I will run it to the battery directly. There's no risk of it causing a dangerous short though because the battery is on the other side of the relay contacts and there's a 10A fuse in that circuit as well. Some cars use the opposite method and put the horn on the battery side of the circuit and connect it to ground with the relay. That means the horn input is always "hot" and has the potential for a short to ground before the contacts, resulting in a horn that won't stop honking unless you pull the fuse or relay.
Wow! Thanks Sam! If I'm understanding correctly, then grounding the "signal ground" from the F/IC at the battery would be ideal. However, would that long a run (probably about 3.5') pick up interference and cause faulty voltage readings? I could run the "signal ground" to the battery. I have tons of wire and conduit. Thoughts?

I have the Scion xD engine control diagrams if you don't. I'd be happy to send that to you if you wanted to let me know if my switched power is actually switched. 🙂

Thanks again!
CrankyOldManWest Michigan · Jun 28, 2019#269
Originally Posted by 06YarisRS ↑
Wow! Thanks Sam! If I'm understanding correctly, then grounding the "signal ground" from the F/IC at the battery would be ideal. However, would that long a run (probably about 3.5') pick up interference and cause faulty voltage readings? I could run the "signal ground" to the battery. I have tons of wire and conduit. Thoughts?

I have the Scion xD engine control diagrams if you don't. I'd be happy to send that to you if you wanted to let me know if my switched power is actually switched. 🙂

Thanks again!
In a perfect world, yes, but only if everything else in the vehicle was able to do that. There's probably a closer ground that's used by the ECU. You'd want to try and use that instead since you're connecting to that part of the electrical system. The other thing you risk doing by running a separate conductor back to the battery is called a ground loop. Basically you're making a new path for electrons to flow between the two ground reference points and causing one of them to be above zero. Here's an article with some examples of automotive grounds.

I should have a copy at home but might not have time to review it tonight.
CrankyOldManWest Michigan · Jun 28, 2019#270
Ok, looking at the wiring diagram now. Yes, pin 1 on A21 (B+) is directly switched by the EFI relay.

Side note--I really hope those aren't iridium plugs. Those type aren't supposed to be adjusted.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 28, 2019#271
Originally Posted by CrankyOldMan ↑
In a perfect world, yes, but only if everything else in the vehicle was able to do that. There's probably a closer ground that's used by the ECU. You'd want to try and use that instead since you're connecting to that part of the electrical system. The other thing you risk doing by running a separate conductor back to the battery is called a ground loop. Basically you're making a new path for electrons to flow between the two ground reference points and causing one of them to be above zero. Here's an article with some examples of automotive grounds.

I should have a copy at home but might not have time to review it tonight.
Ah, yes, ground loop. I am a bit familiar with that having installed a few of my own car stereos.

I did get a hint from the AEM guys. They feel that one of the wires on the TPS is a signal ground. They also said that I do not need to hook up the two 02 sensors and suggested that the most simple setups seem to be the least problematic and most stable.

I also sent my questions, along with diagrams to the turbokits.com guys and Jesse, the lead tech, is sending them to the guys that make the Plug and Play harnesses. So, hopefully I will have definitive answers soon. If you do get a chance to review your diagrams, I'd be thankful, but only if it's not, in any way, an inconvenience for you. I really appreciate the thoughtful and informative responses that you've given so far.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 29, 2019#272
Securing of 3" intake and oil pan sensor install

I need one more 3" clamp, but my intake is now secure. I had to add some rubber padding between the head and piping which I held on with clamps. There should be no rubbing/chaffing now. It was a challenge due to space constraints. Right now I have the 45 coupler supported with pipe strapping. I will readdress this by rigging up a support from the transmission housing. There are a few available bolt holes to attach a custom support. I just have to have the car driveable for my exhaust appointment which is coming right up.

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jun 30, 2019#273
Originally Posted by CrankyOldMan ↑
Ok, looking at the wiring diagram now. Yes, pin 1 on A21 (B+) is directly switched by the EFI relay.

Side note--I really hope those aren't iridium plugs. Those type aren't supposed to be adjusted.
Don't know how I missed this. Thanks very much, Sam, for the confirmation on the switched power supply.

I wasn't aware that the Iriduim plugs shouldn't be gapped. I assumed that turbokits would have taken that into consideration when designing the kit.

I found this video and he does refer to gapping iridium plugs, but I will check with the turbokits guys. Thanks for the heads-up!

https://www.youtube.com/watch?v=cJBG2r1a5qg
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 2, 2019#274
Just got my remaining proposed wire placements confirmed. I had the connections right, but was missing the signal ground. Thanks to Jesse at turbokits.com. It appears that I only have 3 left wires to connect and a startup is imminent. Getting excited...and nervous. Unfortunately, I'll have to wait until Sunday due to prior committments. Fingers crossed that it starts as my exhaust appointment is at 8:00 am on Monday. 😲
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 6, 2019#275
Updates...

After being away for a week at our son's hockey camp in PEI, I got a couple of hours in the garage tonight. To add excitement to our trip, our van suffered a failed wheel bearing - well it got quite noisy. Not having my tools or an adequate way to support the massively heavy van, I had to take it to a garage. They had to use a BFH to remove the rotor, destroying it. Then, they had to literally cut the wheel bearing off with the torches. In the process, they trashed my axle and melted my speed sensor, so a new axle was also needed. I told them to forget about the ABS sensor as I'd get one from rockauto at a fraction of the cost and install it myself. I was there for most of the work and it was legitimately a very tough job and they did try all the appropriate methods. The van had to stay over night and was worked on for at least 6 hours. They charged my 2.5 hours labour. An honest outfit, I'd say. Enough about that...on to the car...

Tomorrow is the 'big day' during which, I reconnect my battery cable, hope to god there are no sparks, load the F/IC basemap and pray that the car will run. I have an appointment on Monday for my exhaust work. In anticipation of tomorrow's start attempt, I filled the car with Pennzoil Platinum 5W30. I'll probably go with 0W20 or 5W20 next time after reading Trevor's posts about oil.

Tonight's efforts:

Installed the MAP vacuum hose for the F/IC. After tapping into the vacuum lines, I ziptied the hose along the engine harness and through the firewall to the F/IC.

Picture not included in this copy

Here is a pic of the engine bay in its current state without the engine cover on. In the upper left corner, you can see the F/IC to ECU wiring, which I completed tonight. The connections I made this evening were for: signal ground, TPS and AFR (B1S1). All of these connections were taps and not intercepts.

Picture not included in this copy

With engine cover on.

Picture not included in this copy

Here is a pic of the (if I remember correctly) TPS connection. I had to add about 2" of wire to ensure enough slack to plug the large ECU plug (C19) back into the ECU. These connections should never fail as they are splayed open, fluxed, interwoven, then twisted, soldered really well, tug-tested and then heatshrinked. Nice to see the goo oozing out of the ends of the heatshrink. Everything will also be taped, run in conduit and taped again.

Picture not included in this copy

I found a great use for my little bits of leftover heatshrink. Many of the wires that I passed through the firewall I subsequently found out I didn't need afterall. So I capped them with bits of heatshrink, pinched then ends when still hot and they welded shut on the ends. I'll tuck these back into the harness before conduit and taping.

Picture not included in this copy

When I was away, I picked up a 3" ID x 2.5" OD coupler for my exhaust. Yes, I will be going with 2.5" piping back to my Megan axleback. Should breathe well.

Picture not included in this copy

Finally, I installed the second temp sensor for the Prosport gauges. If I have time tomorrow after my start and drive attempts, I'll do the gauge wiring and the final mounting of the gauges. The oil pressure gauge may have to wait a few days as I'm rigging up a remote mounting solution for the sensor - for two reasons: 1) it's bulky and likely heavy when filled with oil and I don't want that cantilevered out on the brass fittings at the oil port, and 2) apparently constant engine vibrations shorten the life of these sensors, so mounting it to the frame somewhere should be better. I learned that I can pick up a cheap grease gun hose and because it has 1/8" NPT fittings on both ends, serves as a great hose for the remote mount. Plus, it's rated for 3000 psi or something crazy. Apparently it can easily handle hot oil from the forums I've read and many people are using these successfully with no documented failures.

Trans temp sensor.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 7, 2019#276
Up and Running

I had a few jobs to complete today in prep for my exhaust appointment tomorrow. In the same building is an autoglass business, so the car will roll from one bay to the other.

I had to relocate the air temp sensor as when I went to put the front back on the car, the spot that it normally occupied was filled with intercooler piping. I managed to get it in the airflow, just in the upper opening as opposed to the lower.

It was pretty scary hooking up the battery and turning the ignition. But, everything went well. The car runs well, but occasionally stumbles and regains its rpm. I did have a scary few moments when I thought I'd corrupted the map as I adjusted the fuel injector size and the car stalled and wouldn't start again. I reloaded the basemap and things corrected themselves. Some fine tuning is definitely needed as my fuel trims are still a little whacky, but I'm sure these will be addressed in the tune. I went for a couple short drives and although I tried to stay out of boost, I may have slightly entered it. The torque is simply amazing and I've only revved up to about 3500. The car pulls strongly in the low rpms and I was barely touching the throttle. I will keep things calm until my tune which I'm hoping will be next week.

Picture not included in this copy

ECU wiring done

Picture not included in this copy


Front and wiper tray back on

Picture not included in this copy

Hood on

Picture not included in this copy
tmontagueCaledonia Ont. · Jul 8, 2019#277
Awesome, just awesome!
NYC-SENYC · Jul 8, 2019#278
Woo-hoo! Congrats.
ern-dizCA all day · Jul 8, 2019#279
Originally Posted by tmontague ↑
Awesome, just awesome!
Originally Posted by NYC-SE ↑
Woo-hoo! Congrats.
+1,000,000 👏
heeroyuy01195Florida · Jul 8, 2019#280
Congrats! Glad it's up and running!
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 8, 2019#281
Thanks guys! Exciting times! Got the exhaust done today and will post pics in a bit. The exhaust work is not the most beautiful but is 2.5" and should flow well. The most restrictive point in the system is probably actually the Megan axleback that appears to be 2.25". Exhaust sounds great and I won't need a resonator afterall as I thought I might, though I'll decide after some highway driving.

I do have one MAF code to sort and the rear 02 code but it will be remedied with a defouler. The sensor is actually just hanging out under the car now as I have to extend the wires to go around to the opposite side. Car drives great except for the occasional stumbling at idle but hopefully the tune will help that. Staying out of boost for now. No leaks - big bonus. Haha.

Hoping to hook up my gauges tomorrow but coolant temps are great. I did some testing yesterday and determined that the rad fan comes on around 203F and man it's effective. Temps drop like a rock as soon as it kicks in and that was in my hot garage. This combined with what I've read and Trevor's comments and I'm more optimistic about my cooling system handling the turbo. Maybe the fan will just run a little longer if it needs to.
LeegamerAshland, VA · Jul 9, 2019#282
Great work man. It has to feel good to have it back on the road after doing all of this.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 9, 2019#283
Originally Posted by Leegamer ↑
Great work man. It has to feel good to have it back on the road after doing all of this.
Thanks! It does feel good but will feel much better after the tune. I'm really looking forward to experiencing boost, but must remain patient until my final tune.

After dropping my daughter off at her gymnastics class, I dropped by this garage that had a lot of muscle cars and classic cars in their lot. They referred me across the street to an equipment rental agency operated by a father and son who are both heavily into motorsports. The son has a turbocharged Cobalt and he did all the work himself. He's up for going for a drive with me to check out how the car is running before the tune. Great to make such a contact.

Hopefully today I'll get a sart on wiring my gauges. Will post up progress shots of that.

I had a thought that my MAF code might be due to a dirty MAF sensor. I used an oiled filter for my intake and it was quite juicy. I'll clean the MAF, reset the code and see if it comes back.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 9, 2019#284
Gauge wiring started

I got a couple hours in the garage today and started the wiring. It's coming together well and I found a nice location for the harness I'm making to exit the glove box. It's right between the two change holders and a short drop to the lower hatch access. I still have to figure out where to tap into the headlight switch. I had a look at the wiring diagrams but can't really make heads or tails out of them. So, if anyone knows which wire from the headlight switch becomes live when the headlights are turned on, I'd be most grateful.

You might notice one of the brackets that hold the gauges to the glovebox (far right gauge) is different. In the current chaos of my garage one for the brackets went missing, so I had to modify one from an older set of gauges I had. It actually worked better than the Prosport ones and is more low profile. Gauges are very snug and secure to the dash.

Picture not included in this copy

There are three red and three white wires that can all be combined. These are all ACC power. I plan to tap into the charging port (cigarette lighter, for lack of a better term) located in the lower console. All three orange wires get hooked together and these are connected to the elusive headlight switched power. The three green wires go to the various sensors.

Picture not included in this copy

Conduit housing all the wires. I put a ziptie next to the hole to keep the wiring from pulling on the gauge plugs. The harness is secured on the middle gauge bracket to keep wires from chafing.

Picture not included in this copy

Wires labeled before sending the harness down below

Picture not included in this copy

Wires below

Picture not included in this copy

Glovebox closes perfectly

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 10, 2019#285
Wiring continues...

After getting my head around the wiring diagrams, I have a solution for the headlight switched source (this is what changes the gauge color from white in the daytime to blue at night). I found that pins 7, 8, 9 and 10 in B13 in the fuse box are the park light power sources, so rather than hook the gauges to the headlights and having to figure out the relays, I can just tap into one of the park light lines. I tested the circuit with my multimeter and had 0 volts with the park lights in the off position on the stalk and 12.6V (not running) and 14.2V (running) with the park lights turned on. I have selected the passenger side park light green wire. I will tap, solder heatshrink, wire loom and tape it. The two green wires are for the trans temp sensor and the oil pan temp sensor. I still have to run grounds for the two temp sensors, but I'll run them in the leg of the harness that goes to the sensors. I'm not a big fan of the sensor connectors that are just male and female terminals (much like trailer wiring) with clear rubber sleeves. I'll solder these wires and hearshrink them. If I have to replace the sensors down the road, I'll just cut the wires and resolder/heatshrink.

Looks like my strut tower could use a little degreasing and a fresh application of rust-proofing. It has kept the rust completely at bay however.

Picture not included in this copy

The entire wiring will be soldered, heat shrinked, run through loom and taped and zip tied everywhere in the engine bay as well as behind the dash. There is still a lot to do. I have to remote mount my oil pressure sensor, so I still need some parts. I also need to make my final decision on where I'm going to tap into accessory power.

Here is a pic of the custom harness coming through the firewall. The hole I drilled for the F/IC was just big enough to accommodate this new harness.

Picture not included in this copy

Adding pics as I go.

Here is the switched headlight (park light) power source in its loom. I am thinking about lengthening that leg and running it along the bottom of the strut tower and up in behind. I think it looks pretty poor crossing the tower diagonally.

Picture not included in this copy
CrankyOldManWest Michigan · Jul 10, 2019#286
Looking good!
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 10, 2019#287
Originally Posted by CrankyOldMan ↑
Looking good!
Thanks Sam! It's coming along. Once I get the gauges done I'll be trying to figure out the MAF code I'm getting. I'm going back and forth with AEM but they don't seem to want to tell me if I've wired the MAF correctly or not. I understand their reluctance to provide wiring directions, but on the other hand, it is their product and you would think that they'd offer support with a disclaimer that absolves them of any responsibility if anything goes wrong. I'd surely sign anything to that effect.

Here's they way I have it wired:

Picture not included in this copy
CrankyOldManWest Michigan · Jul 11, 2019#288
What code?
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 11, 2019#289
Originally Posted by CrankyOldMan ↑
What code?
P0101
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 12, 2019#290
Gauge oil pressure sender install

This is a job I had been avoiding for a bit as I wasn't thrilled about messing with my turbo oil supply line that taps into the car's oil pressure sensor port. My believe is that each time you mess with it, you increase the chances of leaks occuring. I had planned to remote mount the OP sending unit and bought a bunch of stuff, but there was simply no way to route the hose (grease gun hose and various fittings) that wouldn't result in the hose chaffing on the engine or frame. This, of course, could result in oil loss and potential catastrophic turbo and engine failure. There just isn't enough room to install the hose and its fittings. So, I added a short 1/8" NPT brass tee and attached the OP sender to that. The fitting structure coming out of the block is extremely secure and strong. Pretty sure you could hang a house off of it.

I have one wire left to connect - the ACC power wire - which I will tap into the grey wire for the power outlet (cigarette lighter) at junction D14 just below and a little left of the steering column. Hope to do this this afternoon, fire up the car and test the gauges.

Tapping for OP sender ground. There is a little recess in the plastic shield, so I marked the perfect spot. The shield will re-install without touching the ground bolt.

Picture not included in this copy

Soldered ring terminal for the OP sensor ground. I had to drill the ring terminal out as the #6 bolt would not fit through.

Picture not included in this copy

Finished ground. Love the Grote 4 times shrinking heat shrink with adhesive, for a water tight seal.

Picture not included in this copy

A couple shots of the OP sensor mounted.

Picture not included in this copy

I adjusted the ground wire for the best flex. Still some taping to do. I taped off the harness and spray painted the bolt and area that I'd sanded to the metal. I'll blast rustproofing down inside the frame channel via the factory holes to where the bolt comes through to deter rust.

Picture not included in this copy

I had to drill a hole in one of the block tabs in order to have a place to attach the oil temp sensor harness.

Picture not included in this copy

There was nowhere reasonable to ground the oil pan temp sensor under the car so I added a grounding point to the strut tower by using an existing threaded hole. I just ran the ground wire back up the conduit that contains the sensor wire.

I also lengthened and tucked away the park light power source harness leg as I didn't like to diagonally crossing the strut tower.

Picture not included in this copy
ern-dizCA all day · Jul 12, 2019#291
I'm enjoying how thorough, meticulous and clean you are with everything. It's a mild OCD's dream.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 12, 2019#292
Originally Posted by ern-diz ↑
I'm enjoying how thorough, meticulous and clean you are with everything. It's a mild OCD's dream.
Haha. Thanks ern-diz! I does satisfy my own mild OCD. Let's see how truly OCD I get when the car is tuned. I like everything (engine and other components) to work as smooth and refined as stock. Hope I don't go falling down any rabbit holes LOL.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 13, 2019#293
F/IC...

In my attempts to restore my edited CAL file (after I adjusted the injector size and the car stalled and wouldn't start), I had forgotten to calibrate the F/IC for TPS and RPM. The RPM was off by about 350. Once I calibrated it, the car/torque and the F/IC are pretty much dead on. I'm showing no codes at the moment, but not optimistic that a couple won't show up after a few driving cycles. After the car heats up to operating temp, I am running a tad rich at idle, but it corrects quickly and returns to stoich. I'm optimistic that adjustments in the fuel and MAF tables will correct this. Also, my rear 02 sensor isn't hooked up (will be later today with a couple of defoulers as I have no CAT). I read that the rear O2 sensor does provide feedback that has an influence on fueling.


Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 14, 2019#294
Gauges operational

The pics do not in any way depict the depth, sharpness and brightness of these gauges. I had to use my flash as the non-flash version of the pics were very burry.


I also tested my trans fan cooler/thermostat/fan setup. The fan fires up right around 185F and you can watch the temp slowly drop as soon as the fan kicks in.

White (daytime)

Picture not included in this copy


Blue (nightime)

Picture not included in this copy

Overall. Still have some work to do on those fuel trims. Once the revs come up, the STFT drops to close to zero and the LTFT starts dropping. The car is running a bit rich.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 16, 2019#295
Update...

Well, the car is running quite well, except that I am not getting any boost. I brought the car up to around 4000 rpm while watchng my manifold pressure gauge and the car stayed in vacuum. I spoke with my tuner and he - as well as the turbokits guys suspect a leak. Obviously, I'd prefer not to deal with this, but I'll chalk it up to another learning experience.

I have rigged up both a smoke tester and a pressure tester. I stole both of the ideas from youtube videos.

The smoke tester is a mason jar with two nipples; one for air (from my portable compressor with regulator), one for a hose that emits smoke. The burning will be achieved by mounting my soldering iron through the mason jar top and into a cloth or old sock soaked in baby oil. From what I've seen, it makes a lot of smoke.

The pressure tester, which will be used to test the charge piping, is basically a 2.5" elbow that I will attach the charge pipe at the throttle body. This end has a PVC cap with a fitting that attaches to my portable compressor as well. I will pick up a 0-30psi gauge at Canadian Tire ($5.99) and that will be screwed into the cap along with the fitting. The other end will plug off the pipe leaving the turbo compressor outlet. I tested the end caps and they can withstand quite a bit of pressure. With the gauge installed, I'll just start with low pressure similar to what my boost will be, 7 - 8 psi.

The smoke machine will be used to check for vacuum leaks.

Picture not included in this copy
tmontagueCaledonia Ont. · Jul 16, 2019#296
Great set up, could you hear anything from the engine bay that was indicative of a boost leak?
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 16, 2019#297
Boost leak

I found a massive boost leak. It's at the funky piece that goes up over the subframe to join the inlet of the intercooler. I had to butcher that piece in order to make it fit. I'll need to order a few bits and pieces but will try adjusting the clamp while I wait for the parts. I may have other leaks to attend to as well, though that was definitely the most questionable union.

This - as suggested by Jesse at turbokits - is probably contributing to my fuel trims being a little whacky. Though I did have some fun tweaking the fuel map yesterday and I could see the improvements in te fuel trims as I made adjustments. I expect I'll have to go back to the preset map values after I fix this leak, and any others.


Pics to follow...
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 16, 2019#298
Originally Posted by tmontague ↑
Great set up, could you hear anything from the engine bay that was indicative of a boost leak?
Yes, you are correct!
LeegamerAshland, VA · Jul 16, 2019#299
It's not a turbo build if you don't have at least one major boost leak after putting it all back together.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 16, 2019#300
Boost leaks fixed!

Well, I learned how important it is to REALLY crank down hard on those T-Clamps. I reseated a couple of the clamps and cranked them down.

Here is my apparatus. It is made up of PVC plumbing caps, rubber couplers, clamps, a pressure gauge and fittings I had lying around. I had a 2.5" elbow left over from my charge piping work.

First, I tested the whole system from my air filter, custom 3" intake and right to the throttle body. I had several leaks, so I then decided to just do the charge side. You can see the cap I replaced my filter with down below.

Picture not included in this copy

I capped off the pipe coming out of the compressor outlet and tested from there to the throtte body. I had a total of 3 leaks. They were bad enough that my little compressor couldn't pump enough air to even move the needle of the gauge I have on my cap.

Picture not included in this copy

My BOV is leaking - not the connection but the BOV itself. Apparently, that's normal but I'm looking into that with turbokits. I plugged the BOV port with a piece of broom handle.

Picture not included in this copy

Holding ~20 psi. I got a little crazy and pressurized up to 25 just for a second and still no leaks. Very happy about this. I bet I'll have boost now.

Picture not included in this copy

Here is my smoke machine that I'll use for the vacuum testing. I may not have any vacuum leaks but it won't hurt to check.

Picture not included in this copy

This is after about 3 minutes after plugging in the soldering iron. If I let it go 5 minutes, it produces a phenomenal amount of smoke.

Picture not included in this copy