Yarisworld Archive

2ZR Turbo Yaris

561 posts · 343,257 views · page 1 of 12

06YarisRSOriginal postFredericton, New Brunswick, Canada · Mar 15, 2019#1
Because I tend to plunge foolishly headlong into things without really thinking, and I always feel compelled to mess with stuff, I just purchased the turbokits.com 2009+ Corolla (2ZR) Turbo kit. I don't expect to start this project for another month, or at least until my unheated garage is hospitable to work in.

Here is the kit:

https://www.turbokits.com/Toyota/Cor...urbo_Kit/1972/

I know that there will be folks that regard this as a bad idea; a risky proposition, but I'm forging forth. It will stretch my mechanical skills to the nth degree, it will be scary, frustrating and exciting at times. I am aware of the inherent risks associated with this project and I am willing to accept them. I think I've read every post in the forced Induction forum a few times - well maybe a little exaggeration. 🙄

Although I have been doing extensive reading and still have much to learn, I have been doing a LOT of research on turbocharged applications, turbos, management, wiring, internal wastgates and actuators, fuel flow, AFRs, wideband sensors, detonation, preignition, fuel mapping, MAF clamping, timing, intercoolers, piping, BOVs etc. I have also been talking fairly extensively with the good folks at turbokits.com. Very helpful and knowledeable guys, that are in the business of retailing performance parts.

Turbo/Manifold Fitment: It appears that there is enough room between the head and firewall to accommodate the turbo. Modifications may be necessary. I'm mildly concerned about the proximity of the turbo turbine to the stock ECU and there may be some adaptations needed for the existing A/C lines. I guess all will be revealed once I try to mount the turbo!

Engine: I am fairly confident that my relatively new engine will handle a very mild boost of 6 - 7 psi as the unmodified (afaik) 2ZR Lotus Elise has a 6+ psi supercharger and produces around 217 HP. My goal would be close to, or less than that.

Transmission: The transmission may be another story. From what I gather (unconfirmed) though, the U340E (Yaris auto) and U341E (Corolla auto, Celica GT) are essentially the same transmisson with the exception of a difference in final drive ratio. The turbokits guys feel that the u340E should be safe up to close to 230 crank hp and have said that there are 1ZZ-powered Celica GTs out there with this transmission that are effectively running 250 hp without mechanical issues. I have doubts about this myself - certainly for any longevity of the transmission. Regardless, I plan to treat the car respectfully - no 0-60 WOT pulls, burnouts or brakestands - will rarely have much payload and certainly won't tow anything. One very knowledgeable YW member termed the u340E as "fairly robust".

Fueling: Fueling is another concern although the turbokits guys feel I should be fine. The only good specs I could find on pumps for the Yaris and Corolla applications are from Delphi (not sure who actually makes the pump in my car - maybe Denso? and neither could the Toyota dealer tell me). Delphi rates, believe it or not, the Yaris at 44 psi, 29 gl/hr, and the Corolla at 44psi, 26 gl/hr and, if memory serves me correctly, both pumps have 5/16" outlets. It's a bit confusing however as the Yaris' pump is rated at 4 amps and the Corolla at 6 amps. Flow rates are probably "free flow", so not sure how valuable those number are. I've been using this calculator below, but I definitely have more work to do. The esteemed, yet unnamed, YW member to whom I referred earlier also stated that the Yaris fuel pump is good up to about 10 psi of boost, of course that's on a 1NZ, not a 2ZR. So, maybe 6 -7 pounds with the 2ZR is achievable, but I suspect it would be risky, especially at the higher fuel/air ratio needed for cooling at the top end of my boost level.

https://www.deatschwerks.com/fuel-ca...ump-calculator

Engine Management Wiring: I have created diagrams of the wiring [Crank, Cams (intake and exhaust), injectors, MAF, AFR etc] that I believe are appropriate for the AEM FIC (30-1910) 'piggyback' and would post them if anyone is interested and/or willing to weigh in on my proposed wiring. DBW would be controlled by the stock ECU and according to the tuner I've been speaking with, likely the timing could also be handled by the stock ECU.


FMIC, intercooler and charge piping: Since the Corolla is obviously dimensionally greater, I'm reasonably confident - after extensive exploration of the yaris engine bay - that I can adapt the piping to fit the Yaris with a small array of couplers, T-clamps, a chop saw and my soon-to-be-homemade bead roller tool.

Engine Cooling: From what I've read here at YW, low boost applications in the Yaris (with the 1NZ) are acceptable for the stock cooling system. An upgraded fan may be necessary, maybe even a radiator upgrade. For a brief moment, I consider meth injection and a non-intercooler setup. Anyway, I guess all will become apparent when tuning. I also have the ability to monitor several sensors via OBD2 and my torque app on my 7" touchscreen. Some of the sensors include: Boost/manifold presure, AFR, STFT, LTFT, injector pulse width (not duty cycle, but the FIC software can read and display this via my laptop), engine coolant temp. I will look toward purchasing and installing oil pressure and oil temp gauges.

Exhaust: Who knows. This will be completed by the outfit that will ultimately tune the car. I expect that it will involve hacking up my new and existing xD midpipe, increasing the tubing to probably 2.25" - 2.5" pipe from resonator back to my Megan axleback.

So, this is my planned project, crazy or not. I did some research before coming on YW and this is partially because I want to look - at least a little bit - like I've thought this through and maybe more importantly, because I so greatly respect many YW members and specifically those who helped me as I muddled through my engine swap. Some of these guys might be shaking their heads as they read this post, but I sure hope they are interested enough in this project to 'get involved' and offer advice and constructive criticism as needed. Of course, if I've missed anything critical from the get-go, please jump right in and let me know.

The kit:

Picture not included in this copy

Replies 560

tmontagueCaledonia Ont. · Mar 15, 2019#2
Awesome stuff man, I'll be following this closely.

My only concern would be the standalone ecu. There have been reports of the 2nd gens and newer ecu's relearning and ruining the tune. I haven't read any first hand experience online but I do think it could he a potential issue.

A standalone would be the way to solve that potential problem albeit at a higher cost

Your stock radiator should handle the cooling fine. It will only become an issue at prolonged time at high load/high rpm (>15mins)
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 15, 2019#3
Hey Trevor. Thanks for jumping in. I did consider a standalone ECU such as the Haltech Elite 550 and the EMS-4, but there were concerns about the handling of peripherals, if I recall, DBW was one. I believe I read that issues related to loss of tune were related to not skewing 02 sensor data. That said, maybe there is a issue with the ECUs you refer to. Since I am running a 2008 xD ECU, I may well encounter issues. The turbokits.com guys say that the tunes are completely stable but I guess we shall see. Maybe in the end, a standalone will be necessary. Thanks again.
myfirstyotaToronto Canada · Mar 15, 2019#4
I'm shaking my head......up and down!!!!! Hell yea man!!!!!

I'll be watching this close too!!!
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 15, 2019#5
Thanks man! I'm excited about it.
I think you had expressed an interest in the kit too, hadn't you? Haha, maybe we could have gotten a better deal buying two kits. I did manage to get a small discount. Still, a lot of quid. Glad you're coming long for the show. And like I said about my 2ZR swap, if nothing else, it might be amusing. 😆
myfirstyotaToronto Canada · Mar 15, 2019#6
Yea but life kinda got in the way. Not to say it won't happen... one day.

I knew it wasn't gonna be cheap. Probably about double what the base kit costs with a couple options, and exchange/duty/shipping. It should be a blast though :)
WeeYariGeorgetown, Ontario, Canada · Mar 16, 2019#7
Ah, winter in NB. The high price of cabin fever ;)

Sent from my EML-L09 using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 16, 2019#8
Originally Posted by myfirstyota ↑
Yea but life kinda got in the way. Not to say it won't happen... one day.

I knew it wasn't gonna be cheap. Probably about double what the base kit costs with a couple options, and exchange/duty/shipping. It should be a blast though :)
Yeah, it was probably not a wise decision from a financial point of view and by the time it's all said and done, it will be a fair bit more. I just went for the basic kit with no upgrades. The only other costs associated with the kit is 15% sales tax when crossing the border back into Canada, but we were planning a trip to Maine anyway and after 48 hours we can each (4 of us) claim $800.00. Technically the kit can be divided into separate invoices as it's a bunch of parts. We shall see. If all goes well, I should be looking at $200.00 - $300.00 for exhaust and about $300.00 for tune. There will of course be other cost along the way. Expensive? Yes. Worth it? I sure hope so!
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 16, 2019#9
Originally Posted by WeeYari ↑
Ah, winter in NB. The high price of cabin fever ;)

Sent from my EML-L09 using Tapatalk
Haha, for sure. Who ever said living in The Maritimes is cheap?
myfirstyotaToronto Canada · Mar 16, 2019#10
Originally Posted by 06YarisRS ↑
Haha, for sure. Who ever said living in The Maritimes is cheap?
Sanity has no price
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 16, 2019#11
Originally Posted by myfirstyota ↑
Sanity has no price
For sure, but insanity certainly does. 😆
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 16, 2019#12
I used the engine control diagrams I got from TIS for the 2008 Scion xD. Also attached is a pic of the 2ZR Engine Control I found online and a link to the F/IC wiring diagram. Please chime in if you see anything amiss or have suggestions. I will add the diagrams for the power supply and ground for the F/IC later.

Interestingly, the tuner with whom I was speaking said that it would be unnecessary for the F/IC to control camshaft timing and that the stock ECU would control that. He seems very knowledgeable, but this just seemed odd to me. I suppose though if it is true and the F/IC is not controlling timing, that the crank would not need to be connected either.

AEM F/IC Manual:

https://www.jegs.com/InstallationIns...17-30-1913.pdf

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
ArmstrongRacingSan Diego · Mar 17, 2019#13
Very cool.

Unfortunately I have no experience turbocharging Toyota’s, so I’ll be learning as well.

1)Bolt on the kit
2)install some gauges to monitor stuff
3)have a tuner advise on the rest....
CrankyOldManWest Michigan · Mar 17, 2019#14
I'm all about this! As far as being hesitant, just remember--someone had to be the first human to eat a durian and they lived to tell about it.

The alternative to this would be to buy a full Elise supercharger setup, which is easily twice the cost when it's all said and done. I wish I had some real advise to give, but this is also out of my area of experience. Definitely staying tuned!
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 17, 2019#15
Thanks Tom and Sam! Just knowing you guys are around gives me a bit of confidence. Hopefully you won't mind if I bounce some theoretical questions off of you or ask your opinions as I go along since both of you unquestionably have more experience with mechanical stuff than I do for certain. It's definitely been a learning experience for me and I haven't even turned a wrench on this project yet.

It does indeed seem like a lot of the guys that were into forced induction have long since moved on. I did read many, many posts on here and there did seem to be a lot of successes.
ern-dizCA all day · Mar 19, 2019#16
Lofty goal, love it! I must be drinking from the same well you are because I've been thinking a lot about going full retard with a 2ZZ swap in mine. Needless to say, I'm subscribed to this thread!
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 19, 2019#17
Originally Posted by ern-diz ↑
Lofty goal, love it! I must be drinking from the same well you are because I've been thinking a lot about going full retard with a 2ZZ swap in mine. Needless to say, I'm subscribed to this thread!
Glad you're coming along for the ride. I will likely need all the moral support I can muster. The 2ZZ swap would be awesome.

As an update to the thread, I got the AEM calibration file and the basemap for my kit yesterday. It's quite interesting to look at although I still need to do a lot of reading to fully understand the numbers.
NYC-SENYC · Mar 19, 2019#18
Originally Posted by ern-diz ↑
I've been thinking a lot about going full retard with a 2ZZ swap in mine.
Then you're going to have to do a license plate swap as well. Think of all that added work!😁
atomic_hojiKincardine, ON, Canada · Mar 19, 2019#19
😲 Awesome! 👍

Definitely following this thread. Like many, also haven't done a turbo upgrade before, but also looking forward to learning along with you - and of course happy to help where I can! 😁

When you say researching turbocharging have you been reading mostly online or have you picked up some good books? Just wondering as I have a selection of books on tuning and forced induction bookmarked for future interest - just curious what you've found as good resources.

When I was lining up the 2ZR swap for my car I had come across this kit and took a few, rough measurements and had also done some reading about the fitment with the Corolla and use of supercharging on the Lotus'. So, for the sake of discussion / second opinion:

My thought on boost is that the specs for the Lotus Cup 250 show it running 11 psi on the stock 2ZR internals. From the Toyota Nation discussions on Corollas that have installed the Turbokits kit it sounds like you're pretty safe if you stay < 8 psi and have a good tune. Starting with a conservative 6 psi or so seems like a good strategy.

I agree that you should (fingers crossed?!) be able to fit everything in behind - there is actually a reasonable amount of room back there! I had intended to move the ECM away from the factory location using the Corolla iM engine harness, but I think the stock Yaris' ECM is up high enough you'd be OK - worst case you might find that you need to run a turbo blanket or heat shield of some sort. Running the air intake and other piping on the Yaris vs. the Corolla will be a bit of a trial and error to see how much modification it will require to fit. Very interested to see how you make out with fitting everything in terms of firewall clearance and intake piping especially.

Regarding engine management - I don't have first-hand experience, but everything I've read (as I'm sure you have) is that to speak to a tuner that is familiar with the unit you're using; seems like you're headed in the right direction! While the standalone route is great, it becomes expensive fairly quickly if you want to control 2x variable camshafts and retain drive-by-wire. You also lose your daily creature comforts / controls that are available in stock ECM - although with a feature-filled standalone you can also add some cool stuff! The suspicion I have with the piggyback reputation for needing a reset is that the tune isn't resulting in predictable feedback to the stock ECM - i.e. the stock ECM works on the principle that it sees X air, demands Y fuel, and expects Z AFR. If your tune interrupts X air, Y fuel, and calculates new outputs - scales the MAF signal to expected range and demands fuel for the real (boosted) MAF signal - such that Z AFR ends up as what the stock ECM is expecting, then the stock ECM will be none-the-wiser. The problems arise when the stock ECM starts making STFT/LTFT adjustments which compound because of the piggyback correction and then settings start to drift. That's my take on it at least - I could be very wrong of course.. lol

You might find you're OK for fuelling on the stock system with running fairly low boost. That might be something to research and have in the back pocket, but see how the tuning works out? If your tuner finds you're leaning out badly because you're fuel limited then do the upgrade, but until then save the cash and see how the stock system works? If all you're changing is the fuel pump and not the lines in the system, fuel rail, etc.. it's easy enough to swap the pump out later. Have you had a look to see what the Lotus Elise with the 1ZR/2ZR is running for fuel flow? Might give you a comparison point.. A glance back at bookmarked threads on Toyota Nation, it seems they've been OK with the stock Corolla fuel system.

No idea about those mushy, smooshy autotragic transmissions.. 😛 But seems like from what you've said that the little U-series holds up pretty well. There are things you can do in terms of valve body upgrades to get a slushbox to handle more torque too if you find you're having transmission issues; never looked for the U340E, so not sure how common or expensive that path becomes..

Oi - that turned out to be long-winded... Never-the-less, looking forward to your updates as you make headway! 👍

-- Adam
MaritimeWoodstock nb · Mar 20, 2019#20
Sign me up. This is great. I also will want to see this in person when it's finished, I'll come meet you at Tim's or McD's in the Bajaris when I finish it LOL.
myfirstyotaToronto Canada · Mar 20, 2019#21
I'd totally be down for a half way Quebec city meet hahaha
ern-dizCA all day · Mar 20, 2019#22
Originally Posted by NYC-SE ↑
Then you're going to have to do a license plate swap as well. Think of all that added work!😁
Whether I go 2ZR or 2ZZ, I think I'd keep the 1NZ plate. I like the sleeper aspect of it lol!

Sorry for straying off topic. Very much looking forward to the 2ZR turbo progress...
LeegamerAshland, VA · Mar 20, 2019#23
This is gonna be sick af.
atomic_hojiKincardine, ON, Canada · Mar 20, 2019#24
Originally Posted by 06YarisRS ↑
...
Interestingly, the tuner with whom I was speaking said that it would be unnecessary for the F/IC to control camshaft timing and that the stock ECU would control that. He seems very knowledgeable, but this just seemed odd to me. I suppose though if it is true and the F/IC is not controlling timing, that the crank would not need to be connected either.
...
Sorry, hadn't replied regarding the wiring diagrams you posted.

From a quick read through the FIC install manual, at a glance it looks like you're spot on with the wiring techniques for those sensors. Does the Turbokits installation instructions give a recommendation on where to splice into the wiring harness? And/Or come with a "flying lead" harness to work with?

With respect to the camshaft and crankshaft inputs - my guess is the tuner means that since you are going to be running a fairly mild tune, you can avoid using the FIC to adjust timing and just leave the adjustment to the stock ECM. Might be that more aggressive tunes that adjust timing are also more likely to freak out the stock ECM, leading to the need to reset? (guessing..) I would hazard a guess that you will still need the crankshaft input as that will be how the FIC will get the rpm - fuel map references rpm if I recall.. The tuner should be able to tell you if you need to wire it in or not for sure though.

Good luck! And of course keep us posted. 👍
-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 20, 2019#25
Hi gents.

Our family has been struck with a particularly virulent flu bug. 🤮 Started with my daughter and then the rest of us fell like dominos. Thank you all for your responses and especially Adam for his thorough, detailed and helpful assessment. I will promptly respond to these as soon as we are better.
ern-dizCA all day · Mar 20, 2019#26
Originally Posted by 06YarisRS ↑
Hi gents.

Our family has been struck with a particularly virulent flu bug. 🤮 Started with my daughter and then the rest of us fell like dominos. Thank you all for your responses and especially Adam for his thorough, detailed and helpful assessment. I will promptly respond to these as soon as we are better.
You're under no obligation, friend. Hope you all get well soon!
myfirstyotaToronto Canada · Mar 20, 2019#27
Originally Posted by ern-diz ↑
You're under no obligation, friend. Hope you all get well soon!
+1
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 21, 2019#28
Thanks gents! Well, as nasty as that was, it was short-lived. Still not 100 % but definitely a lot better.
MaritimeWoodstock nb · Mar 21, 2019#29
Gotta love when the kids bring those bugs home for school or daycare. Glad you're on the mend.
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 21, 2019#30
Originally Posted by atomic_hoji ↑
😲 Awesome! 👍

Definitely following this thread. Like many, also haven't done a turbo upgrade before, but also looking forward to learning along with you - and of course happy to help where I can! 😁

When you say researching turbocharging have you been reading mostly online or have you picked up some good books? Just wondering as I have a selection of books on tuning and forced induction bookmarked for future interest - just curious what you've found as good resources.

When I was lining up the 2ZR swap for my car I had come across this kit and took a few, rough measurements and had also done some reading about the fitment with the Corolla and use of supercharging on the Lotus'. So, for the sake of discussion / second opinion:

My thought on boost is that the specs for the Lotus Cup 250 show it running 11 psi on the stock 2ZR internals. From the Toyota Nation discussions on Corollas that have installed the Turbokits kit it sounds like you're pretty safe if you stay < 8 psi and have a good tune. Starting with a conservative 6 psi or so seems like a good strategy.

I agree that you should (fingers crossed?!) be able to fit everything in behind - there is actually a reasonable amount of room back there! I had intended to move the ECM away from the factory location using the Corolla iM engine harness, but I think the stock Yaris' ECM is up high enough you'd be OK - worst case you might find that you need to run a turbo blanket or heat shield of some sort. Running the air intake and other piping on the Yaris vs. the Corolla will be a bit of a trial and error to see how much modification it will require to fit. Very interested to see how you make out with fitting everything in terms of firewall clearance and intake piping especially.

Regarding engine management - I don't have first-hand experience, but everything I've read (as I'm sure you have) is that to speak to a tuner that is familiar with the unit you're using; seems like you're headed in the right direction! While the standalone route is great, it becomes expensive fairly quickly if you want to control 2x variable camshafts and retain drive-by-wire. You also lose your daily creature comforts / controls that are available in stock ECM - although with a feature-filled standalone you can also add some cool stuff! The suspicion I have with the piggyback reputation for needing a reset is that the tune isn't resulting in predictable feedback to the stock ECM - i.e. the stock ECM works on the principle that it sees X air, demands Y fuel, and expects Z AFR. If your tune interrupts X air, Y fuel, and calculates new outputs - scales the MAF signal to expected range and demands fuel for the real (boosted) MAF signal - such that Z AFR ends up as what the stock ECM is expecting, then the stock ECM will be none-the-wiser. The problems arise when the stock ECM starts making STFT/LTFT adjustments which compound because of the piggyback correction and then settings start to drift. That's my take on it at least - I could be very wrong of course.. lol

You might find you're OK for fuelling on the stock system with running fairly low boost. That might be something to research and have in the back pocket, but see how the tuning works out? If your tuner finds you're leaning out badly because you're fuel limited then do the upgrade, but until then save the cash and see how the stock system works? If all you're changing is the fuel pump and not the lines in the system, fuel rail, etc.. it's easy enough to swap the pump out later. Have you had a look to see what the Lotus Elise with the 1ZR/2ZR is running for fuel flow? Might give you a comparison point.. A glance back at bookmarked threads on Toyota Nation, it seems they've been OK with the stock Corolla fuel system.

No idea about those mushy, smooshy autotragic transmissions.. 😛 But seems like from what you've said that the little U-series holds up pretty well. There are things you can do in terms of valve body upgrades to get a slushbox to handle more torque too if you find you're having transmission issues; never looked for the U340E, so not sure how common or expensive that path becomes..

Oi - that turned out to be long-winded... Never-the-less, looking forward to your updates as you make headway! 👍

-- Adam
Hey Adam!

Thanks very much for the input.

Among other sources such as articles and forums, I've been working my way through Corky Bell's, Maximum Boost.
Still trying to get my head around such things as tensile and compressive forces in an engine - steep learning curve. If I'm interpreting it correctly, the potential destructive forces on engine mechanicals under boost are less than what I had assumed. Also, the focus on heat management in all aspects of the turbo system is strongly promoted as the leading way to ensure long-term durability. I think your suggestion about going for 6 psi is a very good one. I could always up it a smidgen if everything was in order and performing well.

Regarding fitment of turbo and piping, I guess I'll find out when I start. One of my colleagues has a '12 Corolla, so I intend to go out and do a quick comparison between it and the Yaris in terms of firewall to head clearance. It looks like the turbo sits low enough to get into that exhaust tunnel area, so I'm hopeful. Not sure what's directly behind that in the event that I have to get a big hammer out and make room. 😲 Yes, I've also been looking at turbo blankets for the turbine. I think that would be very beneficial.

I did speak with Jesse at turbokits.com regarding the capablity of my fuel pump. He had very positive things to say about the durability, capability and longevity of the pumps Toyota uses. He believes that I would not need to do an upgrade on the pump at the boost level I seek, but, again, recommended that my tuner advise me in that area.

Regarding the transmission, I purchased an ASE Mobilis research paper on the U340E and it rates the max torque of the trans at around 140 ft/lbs

A quote from Corky Bell:

"Will the transmission and drivetrain be adversely affected?

Very Unlikely. Consider that the drivetrain endures more torque in first gear from the stock engine than almost any turbo can produce in second gear..."


Maybe I'm tailoring the info to placate myself, but the above, coupled with claims by Monkey Wrench Racing that the U340E is good up to 250+ in turboed 1ZZ Celicas leads me to believe that I at least have a chance of good results. I did speak to a nice fella at importperformancetrans as they produce a high capacity U340E/U341E transmission. He, of course, definitely recommended a performance transmission for my turbo application, but he's in the business. When queried about what he would do to the trans, he mentioned a performance valvebody (I know these exist, as MWR sells them), different clutch material and metallurgical treatments (I think Tom discussed these when building one of his transmissions). I won't be trashing on the transmission, but I guess only time will tell how it holds up. I just have to stop worring about it and move on.

Jesse recommended that I do hook up the cams to the F/IC. He says that it would probably be possible to let the stock ECU handle the cams but the functionality is there and should be used. Timing is going to need to be pulled as boost increases, I believe. As far as where to tap/intercept the harness, it can be done close to the ECU connector. I figured I'd go 8 - 10" inches from the connector and that would put me closer to my glovebox, behind which I'll probably mount the F/IC.

BTW, I got my Fedex Tracking numbers today as well as a call from turbokits.com. Getting excited here!
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 21, 2019#31
Originally Posted by Maritime ↑
Sign me up. This is great. I also will want to see this in person when it's finished, I'll come meet you at Tim's or McD's in the Bajaris when I finish it LOL.
Absolutely! It's a must do!
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 21, 2019#32
Originally Posted by myfirstyota ↑
I'd totally be down for a half way Quebec city meet hahaha
Hell ya. I really want to come up to the GTA for a meet - such as what you guys have been taking about - but something about a turboed Yaris, a wife, 2 kids and luggage seems impractical. We will be in Toronto in July, but unfortunately, it wouldn't be the Yaris getting us there. It would be the van - yawn!
myfirstyotaToronto Canada · Mar 21, 2019#33
Originally Posted by 06YarisRS ↑
Hell ya. I really want to come up to the GTA for a meet - such as what you guys have been taking about - but something about a turboed Yaris, a wife, 2 kids and luggage seems impractical. We will be in Toronto in July, but unfortunately, it wouldn't be the Yaris getting us there. It would be the van - yawn!
Tow bar! Lol
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 22, 2019#34
Originally Posted by myfirstyota ↑
Tow bar! Lol
Ah, interesting idea!
atomic_hojiKincardine, ON, Canada · Mar 22, 2019#35
Eeeeww - glad to hear it was short lived! Blech, stomach viruses are terrible.. 👎

Interested to hear what you think of the book overall when you get through it - I've heard very polarized reviews of it.

Sounds like Turbokits customer service is good - always a bonus to deal with a company that backs-up the product after the sale. Glad to hear the stock fuel system appears to be up to the task. re: FIC install - I guess in the worst case you hook-up the cam sensors and leave control to the stock ECM, as long as it doesn't cause signal noise or problems for the stock ECM then it was just an extra wiring step.

I'm not sure I'm on-board with the automatic rationale - not because I don't think the U340E can do it more the author's reasoning is a bit mis-placed I think - if the engine makes more torque (it better if it's got boost, lol) than stock, it does so in all gears. Comparing a turbo pull in second to a stock pull in first isn't really relevant - you're still going to use first gear with the turbo! lol Especially true in an automatic because you can't start in second gear. Maybe there's more context to the statement... 😁 I'm sure IPT would love to sell you a very expensive transmission, lol. The tech. specs from the ASE paper are probably pretty reliable, but more than likely conservatively biased toward daily driving and long-term reliability vs performance from an OEM point of view. The MWR experience is more real-world and good, but like anything, I'll bet your driving style will be the biggest factor. My gut feeling is start with a transmission cooler (since automatics don't live long with heat) and see how that goes. If you're finding issues then consider a shift kit or valve body upgrade.

Tracking is exciting! 👍

Definitely keep us posted if you are going to make it out this way this summer.

Looking forward to unboxing, progress, and booooooost! 😁
-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 22, 2019#36
Originally Posted by atomic_hoji ↑
Eeeeww - glad to hear it was short lived! Blech, stomach viruses are terrible.. 👎

Interested to hear what you think of the book overall when you get through it - I've heard very polarized reviews of it.

Sounds like Turbokits customer service is good - always a bonus to deal with a company that backs-up the product after the sale. Glad to hear the stock fuel system appears to be up to the task. re: FIC install - I guess in the worst case you hook-up the cam sensors and leave control to the stock ECM, as long as it doesn't cause signal noise or problems for the stock ECM then it was just an extra wiring step.

I'm not sure I'm on-board with the automatic rationale - not because I don't think the U340E can do it more the author's reasoning is a bit mis-placed I think - if the engine makes more torque (it better if it's got boost, lol) than stock, it does so in all gears. Comparing a turbo pull in second to a stock pull in first isn't really relevant - you're still going to use first gear with the turbo! lol Especially true in an automatic because you can't start in second gear. Maybe there's more context to the statement... 😁 I'm sure IPT would love to sell you a very expensive transmission, lol. The tech. specs from the ASE paper are probably pretty reliable, but more than likely conservatively biased toward daily driving and long-term reliability vs performance from an OEM point of view. The MWR experience is more real-world and good, but like anything, I'll bet your driving style will be the biggest factor. My gut feeling is start with a transmission cooler (since automatics don't live long with heat) and see how that goes. If you're finding issues then consider a shift kit or valve body upgrade.

Tracking is exciting! 👍

Definitely keep us posted if you are going to make it out this way this summer.

Looking forward to unboxing, progress, and booooooost! 😁
-- Adam
Thanks Adam!

Turbokits does seem like a really good outfit. Jesse (the lead tech) seems like a very straight-talker, no nonsense and solution-focused kind of guy. I'd rather 'realistic' than 'accommodating'. He seems very optimistic about my project, though this one, I think, is a little different than anything that they have been involved in in the past. Suffice to say, I feel like I'm in good hands.

I like the Corky Bell book so far, but I'm really not that far into it. It seems to cover many fundamentals, so represents a good starting point for me, I suppose. If you have any recommendations for digitally available books/sources, as a general introduction to tubrocharger systems, I love to hear about them.

Yes, the Corky Bell statement about 1st and second gear - N/A vs Turbo doesn't really seem to hold much water. Of course, you are correct about boost being present in 1st gear as well as all gears. If anything, it tells me that if I want to preserve my transmission, maybe I ought not command full boost in 1st gear, lol! But, I suppose, that's common sense. I guess, in a large sense, I'm trying to convince myself - with or without valid data - haha, that I will be safe. Undeniably un-scientific, I know.

I thought about a transmission cooler, but without confirming that a cooler would not contribute to restricted flow, I'd have to do a bit more research first. I've read conflicting information about placement of a cooler (I just happen to have a tube and fin cooler in my garage, less effective than a plate and fin config) and whether it should be a) used without the stock in-rad cooler, 2) installed before the in-rad cooler or 3) on the return line. I know that cooling is very important, but my immediate concerns would be two: 1) slipping clutch packs under additional torque and 2) actually breaking hard parts, such as stripping a gear, or snapping an input or output shaft. On another note, you'd mentioned axles. Which, brings me to two questions for the YW community: 1) are axles likely to fail before transmission hard parts? And, 2) are the Scion xD axles a direct fit (lengths, spline count) with the auto? I'll dig back in the forums, but I think discussion around this topic was focused on the manual trans. EDIT: different input shaft spline count, xD 20 and Yaris 23.

Well, it seems that my packages are almost at their destination. Not sure if we'll get over this weekend to get them. But, I'd say that un-boxing isnt that far off.

I do have an immediate challenge to face right off the bat, sadly. It seems that the spring bolts that attach the midpipe to the stock exhaust manifold are stripped. When we worked at straightening out the exhaust in the school shop, we realized that the bolts would turn but not back out. I don't believe that they were over tightened on the install but maybe they were. Or, the wrong ones were installed. I left it for the time being as I had no exhaust leaks, but had planned to have the exhaust guys fix that when I went for the resonator - axleback pipe diameter upgrade. Not quite sure how I am going to approach this but it might look something like cutting my midpipe and then working the lot out from below. Whatever happens will have to happen in my garage as a trip to an exhaust shop isn't in the cards at the moment. The downpipe supplied with the kit, extends well beyond the stock converter anyway, and the converter/resonator section is going to have to be chopped up and rewelded anyway.

Last evening I spoke with the tech from BLP Automotive - my future tuner guys - about fueling. He also feels I should be fine at 6-7 psi, but that they have in-stock solutions, one of which is a voltage regulator module that bumps up the pump output by increasing voltage, plus a small selection of in-tank pumps. I would prefer, the latter, but he will advise at the time.

Once I receive the kit, I'll be sure to post up pics of some of the larger individual parts as well as a segment on my experience with clocking the turbo. Apparently, some arrive needing to be clocked.
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 22, 2019#37
I plan to order an exhaust manifold gasket. Logic tells me that metal beats composite, but would take suggestions for my project. I assume that the OEM is metal.
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 24, 2019#38
Due to hockey practice and gymnastics, I will have to experience delayed gratification, unfortunately.

I did get a sneek peek as I have to open the boxes before crossing back into Canada. CBSA agents frown upon un-opened boxes.

Pics tonight for anyone interested.

Picture not included in this copy
myfirstyotaToronto Canada · Mar 24, 2019#39
And who T.F. isn't interested!?!?!?!?!?!? Hahaha
tmontagueCaledonia Ont. · Mar 24, 2019#40
Originally Posted by myfirstyota ↑
And who T.F. isn't interested!?!?!?!?!?!? Hahaha
😆 no kidding, I feel like its Christmas all over again
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 24, 2019#41
Gotta say, Turbikits.com produce what seems like very high quality stuff. They also take great care in packaging. I did not opt for the cold air intake, but have asked the guys if there would be a performance difference and if the 'warmer' intake air from behind the engine would cause problems - with the filter attached directly to the compressor. I expect they'll say that the intercooler is more than enough to handle the warmer air. It is one BIG intercooler - hopefully I can make it fit! Also, the "cold air intake" places the filter basically beside the block (or at least would be in the more confined Yaris engine bay) so I don't think the intake air from behind the engine would be that much hotter anyway. We shall see what they say. After reading several threads about placing the filter directly on the compressor intake, I discovered there is much debate; lots of stated pros and cons for either approach.

T28, BTW, does have to have the compressor clocked 180 degrees counter-clockwise from its current position.

Picture not included in this copy

Picture not included in this copy

One of my Favs...downpipe. There is another sensor bung for the AFR sensor on the opposite side right up by the flange. If I am indeed going to go without the front Cat, I'm going to have to figure out how to eliminate the CEL that will show up. I think the F/IC has a strategy for dealing with it.

Picture not included in this copy

Definitely my fav part...manifold:

Picture not included in this copy

Picture not included in this copy

F/IC

Picture not included in this copy

Injectors

Picture not included in this copy

BOV

Picture not included in this copy


Piping (Good heavy gauge and exceptional welding). I can show a close up of the welding quality if anyone would like to see it.

Picture not included in this copy

Intercooler

Picture not included in this copy

1 bag of misc hardware

Picture not included in this copy
LeegamerAshland, VA · Mar 25, 2019#42
Looks like good quality stuff.
WeeYariGeorgetown, Ontario, Canada · Mar 25, 2019#43
Missing from pics - 1 intercooler

Sent from my EML-L09 using Tapatalk
ern-dizCA all day · Mar 25, 2019#44
Picture not included in this copy
LeegamerAshland, VA · Mar 25, 2019#45
Originally Posted by ern-diz ↑
Picture not included in this copy
bing bong bing bong bing
ern-dizCA all day · Mar 25, 2019#46
I am very excite 😁
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 25, 2019#47
Originally Posted by WeeYari ↑
Missing from pics - 1 intercooler

Sent from my EML-L09 using Tapatalk
Ah, so it is... Will rectify immediately!
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 25, 2019#48
Originally Posted by Leegamer ↑
bing bong bing bong bing
AWESOME! Haha
06YarisRSThread starterFredericton, New Brunswick, Canada · Mar 25, 2019#49
Originally Posted by ern-diz ↑
I am very excite 😁
Me too! Approaching project with mild trepidation, however. Hoping to go out this weekend and attempt to get that dang exhaust off.
WeeYariGeorgetown, Ontario, Canada · Mar 25, 2019#50
Originally Posted by 06YarisRS ↑
It is one BIG intercooler
It certainly is!
It looks bigger than specs on the site. Must be skinny plank flooring that it is resting on.

Sent from my EML-L09 using Tapatalk