Yarisworld Archive

2ZR Turbo Yaris

561 posts · 343,257 views · page 4 of 12

Replies continued

06YarisRSThread starterFredericton, New Brunswick, Canada · May 1, 2019#151
Very little time tonight, but I installed the BOV and picked up some hardware for my trans cooler.


Picture not included in this copy

Picture not included in this copy

5/16" compression to 3/8" barb fittings and 8' of transmission cooler hose.

Picture not included in this copy

I'm going to move the trans cooler forward and install one of these behind it as a puller fan. I did some work on the A/C aluminum lines and hoses tonight. With minimal and careful bending, I cleared up a nice 3 1/2" to 3 3/4" space behind where the trans cooler will sit. The puller fan, mounted on the engine side of the trans cooler is only 2 1/3" deep, so there will be lots of room to exhaust the air into the engine bay. As much as I'd like a dedicated sensor and thermostat plumbed into the trans line to control the fan, I'm just going to hook it up to the radiator circuit and have it come on with the rad fan as this is the setup for.most trans/oil coolers.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 2, 2019#152
Transmission Fittings and Cooler Mounting

Compression fittings worked great. Simply cut off the bubble flares and installed the fittings. I'll have to loop the hose around and attach it to the chassis at a couple points with my rubber coated P clips. Glad I bought a long piece of hose.

From underneath.

Picture not included in this copy

From above.

Picture not included in this copy

Cooler mounted. Still have to secure the bottom with brackets.

From front.

Picture not included in this copy

From back. Lots of room to mount the 8" fan.

Picture not included in this copy

All the coolers.

Picture not included in this copy

I'm in Moncton, NB tomorrow for a conference and afterwards I'm going to visit BLP Dyno and Automotive, the guys who will be tuning my car. Looking forward to that. Maybe I'll get really lucky and see them tuning a car.
tmontagueCaledonia Ont. · May 3, 2019#153
Nice work! How do you plan in mounting the trans cooler? Also how will you be wiring your trans cooler fan, thermostatically controlled?
06YarisRSThread starterFredericton, New Brunswick, Canada · May 3, 2019#154
Originally Posted by tmontague ↑
Nice work! How do you plan in mounting the trans cooler? Also how will you be wiring your trans cooler fan, thermostatically controlled?
The cooler is secured at the top very solidly with the rubber coated P clips. They do a great job of holding it tight. I just have to fab up a couple small brackets for the bottom. I'm on the fence about the electrical. I was planning on just wiring it to the rad circuit but I know it's not ideal. I would love to have it separately controlled with its own thermostat but that would require a lot of additional plumbing, sensor port, relay etc. An engine oil cooler with fan wired to the rad fan makes sense to me as oil temp and coolant temps are reasonably close, but I expect trans fluid could get very hot before the coolant gets to the point where it commands the fan to turn on.

I was speaking to a transmission tech yesterday and he felt that wiring it to the rad fan is a viable option as most trans coolers sit in front of the rad. Not really sure what to do at this moment.
myfirstyotaToronto Canada · May 3, 2019#155
Is the fan really needed? Just simply having an oil cooler is a great upgrade.

I would think the only time the cooler would need to do it's job is when you're givin'er. There should be enough air flow through the cooler when your right foot is down, no?

I'd save the extra weight and money
06YarisRSThread starterFredericton, New Brunswick, Canada · May 3, 2019#156
Decided to buy one of these. I'll tap a brass fitting and couple it into the 3/8" line after the cooler and before the pan. This sensor turns the fan on at 180 and off at 165.


Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 3, 2019#157
Originally Posted by myfirstyota ↑
Is the fan really needed? Just simply having an oil cooler is a great upgrade.

I would think the only time the cooler would need to do it's job is when you're givin'er. There should be enough air flow through the cooler when your right foot is down, no?

I'd save the extra weight and money
You are probably correct. Definitely when moving it should be ok, but I was strongly advised by folks that turboed the 1ZZ auto to have a big trans cooler. I've already ordered the sensor/thermostat and this is the kind of design thing I crave. Haha. I would have done an oil cooler but that would be a much bigger and more expensive job to do correctly. I will install an oil temp gauge and if I see issues, I'll look into the filter concersion kit, sandwich plate and cooler.
myfirstyotaToronto Canada · May 3, 2019#158
Sorry I should have specified trans oil or fluid
06YarisRSThread starterFredericton, New Brunswick, Canada · May 3, 2019#159
Originally Posted by myfirstyota ↑
Sorry I should have specified trans oil or fluid
Haha, no worries. I wanted to address the topic of the engine oil cooler anyway.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 3, 2019#160
Some Light Bracket Fabrication

Although I didnt get much actual work done on the car today, I did have a great visit with the outfit that will be tuning my car. Unfortunately, I arrived a few minutes late to see a dyno run on a turboed BMW. Not being a big BMW guy, I don't know the model. Had a very nice chat and got a lot of questions answered and fears allayed, LOL. I did get to look at a number of turbo projects that are underway. Looking forward to "the big day".

On my way home from today's conference, I stopped by a scrapyard and bought $2.00 worth of aluminum strips/plate. It's nice and heavy but bends really well in my vice with some force.

Intercooler Upper Brackets. I filed down the edges and they look pretty good. I didn't bother to paint them.

Picture not included in this copy

Once I tighten these up, it will lift the intercooler about 1/4" which will result in the perfect placement.

Picture not included in this copy

I did manage to get one hole drilled up through the crash bar, but will have to pick up another bit as mine is toast. I tried sharpening it on the bench grinder but it was no better. That crash bar steel is capital "H" hard!

Lower Trans Cooler Bracket. This couldn't have been more simple and I didn't even have to drill a hole in the car as there was one already there that lined right up. Right now the lower part of the cooler isn't screwed to the bracket but the whole thing is extremely solid. I may just glue the cooler's lower mounting tab to the bracket with RTV. Getting in there to drill would be challenging, though I could probably do it with my angled drill attachment and pop in a couple self-tapping screws. Yeah, I'll do that.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

I also picked up some fittings to mount my inline trans fan thermostat. This should be really simple wiring wise as no relay is needed. Just one power wire in split loom from the battery and ground at the fan. This is basically what I will piece together.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 5, 2019#161
Final Intercooler and Trans Cooler Mounting

Got the second hole drilled through the crash bar. I have finally come to understand what is meant by a "high speed" metal drill bit. My pathetic little cordless drill doesn't spin fast enough to cut well. I borrowed my neighbour's corded drill and it cut through fast. My corded drill bit the dust a while back. Time to pick up another one.

Final mount for intercooler. This thing is rock solid. I positioned it to maintain all of my piping clearances.

Picture not included in this copy

Drilled and used self-tapping screws to secure the lower part of the trans cooler to the lower bracket. Again, extremely solid.

Picture not included in this copy

Throttlebody/MAF charge pipe in final position. With the Corolla this actual pipe comes closer to the throttle body and the clamps would be closer together. I have about 2" of coupler between the end of the pipe and the throttebody. I hope this doesn't cause too much ballooning of the coupler. Worst case scenario, I put a wide clamp on the coupler about 1/2 way. Will have to consult the tuner on this one.

Picture not included in this copy

Oil catch can... I spoke with the tuner today via IM and he says that my stock PCV system will be fine with this fairly low boost application. I told him I planned to put a breather/filter on the valve cover outlet and he said that's exactly what he would recommend. I may still pick up a catch can and install it.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 5, 2019#162
Bumper Cover Test Fit

Very happy that the cover fits on perfectly and all clearances are maintained. The intercooler is not completely centered, but that's just the way it has to be due to the passenger side piping/frame considerations.

The nice part of all this is that every cooler has great airflow over it.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 5, 2019#163
Plumbing the Trans Cooler

Of course the transmission fittings were not pointing in optimal directions to plumb the cooler circuit. This necessitated some looping, so I'm glad I bought a bit of extra hose. I have very smooth curves in the hose, so no threat of kinking, plus this tubing can almost be folded over on itself and still flow.

Loose fitting the hoses and deciding on clamping points. There is a natural pathway just below the rad fan and lots of holes to place P-clips. I can easily do this with no contact with the car chassis parts at all.

Running cooler return line

Picture not included in this copy


I haven't decided whether I should put the trans fan thermostat in the line exiting the transmission or returning to the transmission. I'm leaning toward putting it in the line out of the trans as that fluid will be hotter and therefore turn the fan on sooner.

I've also calculated that the addition of the cooler and around 8' of hose will result in ~ a 0.3L increase in ATF capacity.

A couple pics from below. No clamps yet, they'll be installed last.

Picture not included in this copy

Picture not included in this copy

And, one from above

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 6, 2019#164
Transmission Cooler Fan Mounted

This was a nice job with the only tricky bit being the working of the mounting straps carefully through the cooler from the back. It took some contortionist maneuvers. The fan is very secure and sits nicely in about the middle of the cooler. Just have to run a fused supply 12 or 14 gauge wire through conduit to my inline thermostat, then on to the fan.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 6, 2019#165
Oil Catch Can

I picked up a Chinese knock-off of the Mishimoto 2 port can from eBay. No doubt that the materials and craftsmanship are subpar when compared to the Mishimoto, but, dang, it looks identical in every way, inside and out.

I wasn't going to do a catch can but after more reading and removing the PCV tube at the intake, I saw the ugliness. Pic below. I don't need any of that crap entering the intake for many reasons, none the least being the adverse effect it would have on my octane rating and increased threat of detonation. I'll proceed as planned with the valve cover breather and install the 2-port between the PCV valve and intake.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 9, 2019#166
Passenger Side Piping

This 2" pipe did not enjoy being bead rolled. Although it's a bit rough, it will seal well and hold well with the clamp. I had to cut the piece from the kit into three separate pieces and discard one piece. I'll now have to order a 2" 45 degree coupler. Good new is that it will fit well and all the other piping is done. This is the last bit of piping for the project.

My trans cooler thermostat arrived today and I'm expecting my catch can to arrive tomorrow. Time permitting, this weekend, I'll have the trans cooler all done, the catch can mounted and plumbed. The helpful guys from turbokits.com sent me a piece of 3" intercooler piping as I was short to mount my air filter. Hopefully I'll get that mounted this weekend too. Then it's time to move on to the F/IC wiring. Still a ways to go, but getting there.

Passenger side plumbing. It's solid as a rock and due to the support clamp that bolts to the A/C compressor, I have a good amount of clearance between the turbo compressor coupling and the subframe.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 11, 2019#167
Oil Catch Can and Air Filter Mounting

Managed to eek out a couple hours in the garage tonight. I installed my oil catch can but have yet to tie it in to the PCV system. I need two couplers and a few more clamps. I'll tidy up the ugly ends of the hoses, which I scavanged from one of the numerous old engines in our shop.

I received my short section of 3" intercooler piping from the awesome dudes at turbokits.com so I got my air filter test mounted. Next, I'll make a support bracket to secure the air filter/pipe and strap down all the various hoses etc.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

I also picked up my transmission fan thermostat today. Truthfully, I don't have a lot of faith that it will last very long, but you never know. It's rated for 15 amps and my fan apparently draws 6 - 8, so it shouldn't overstress it.

Picture not included in this copy
tmontagueCaledonia Ont. · May 11, 2019#168
Looks good so far. Definitely cut a vent in your front bumper for the air intake, it will make a difference when you're moving for intake temps
06YarisRSThread starterFredericton, New Brunswick, Canada · May 11, 2019#169
Originally Posted by tmontague ↑
Looks good so far. Definitely cut a vent in your front bumper for the air intake, it will make a difference when you're moving for intake temps
Thanks! Although I would be reluctant to cut any holes in my bumper, there is a section of plastic about 3 inches wide on the right side of the radiator. After reading your suggestion, I am thinking about modifying this section to funnel air toward the filter, which is perfectly in line with it. I figured if I cut this off, I could use brackets to angle it to direct air from the upper bumper opening onto the filter. The area below the filter is wide open and quite airy toward the bottom of the engine bay, so I think the intake air shouldn't be too hot. That said, it is partially behind the rad. I have a fair bit of adjustment with the filter as it is, so I could actually point in down and closer to the bottom of the engine bay, but not too far as to pic up road debris or water from the wheels.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 11, 2019#170
A little plumbing this afternoon

So, the eBay seller said that the barb fittings for the inline transmission fan thermostat were 3/8". Well, they're 1/2". It was completely impossible to get the 3/8 hose onto the 1/2" barb despite lubing the fitting and hose, boiling the hose end in hot water etc. I bought a foot of 1/2" hose, two 1/2" x 3/8" reducing couplers and a few clamps. Done. I was initially worried about restriction when downsizing from 1/2" to 3/8", until I cut the PCV hose to run to the catch can and was surprised to see that it reduced down to 5/16" or even smaller. It's really a tiny hole, not much wider than a small drinking straw, running through that hose. If anything, the 3/8" piping and fittings I have in there now will provide better flow when in vacuum. I'm guessing they use such a thick wall to avoid the hose collapsing under vacuum. The hose I bought is good for 24" of vacuum and I will also have the valve cover breather that should help vent the block.

I also decided to swap out the plastic 1/2" outlet and inlet on the catch can for aluminum 3/8" barbs. This will make for a much cleaner looking and efficient install. The catch can came with a gate valve drain which is a nice touch. I'll run a foot or 18" of hose down toward the bottom of the engine bay for easy draining.

The coupling and 3/8" barbed fittings just in front of the catch can is the beginnings of my trans temp gauge inline fitting. I'll buy a gauge with a 1/8" npt sensor and drill and tap the brass coupling. I purposefully bought one with the thickest wall I could find for the best threading (tapping) result.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 11, 2019#171
Catch can done, finally!

This turned out to be more involved than I had expected. The pipe that goes from the PCV valve under the manifold - thanks Toyota - is basically a "U" shape that loops around back to the manifold. So, when you cut it to splice into it, it's very difficult to get the fittings on, expecially since the interior diameter of this piping is so narrow and you have so little length to work with. I simply could not get enough leverage to seat the fitting because the piping is tucked up under the throttlebody. So, that had to come off (I would have taken the manifold off, but I expect it would be a struggle given the close proximity to the rad in this smaller engine bay). It did give me a chance to inspect the throttlebody surfaces and gasket, which fortunately, though a little dirty, were in good shape. The other challenge is getting the piping in in a way that ensures that it won't chafe on other piping, clamps or on body and engine parts when the engine moves around. Anyway, it's done now.

Getting can ready for final install

Picture not included in this copy

Picture not included in this copy

Throttlebody removal

Picture not included in this copy

Picture not included in this copy

Finished, with zip ties to keep everything secure. They're white which I hate, but it's all I had on hand, so they'll be replaced with black ones. Also going to look for side by side double hose retainers, so I may get rid of the zip ties all together.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 12, 2019#172
Trans thermostat and plumbing done

The circuit is now complete. Looking forward to starting the car - will be a while yet though - and checking for leaks. I just have two mounting points using the rubberized "P" clips left for the hoses which requires pre-drilling and using self tapping screws - the metal is a touch too thick to self tap. There was one spot there the inlet and outlet hoses are touching, so I cut a short section of pipe, wrapped one of them and ziptied the rubber hose piece on. Everywhere else there is no contact and room for movement.

The sensor is installed on the outlet of the factory in-rad cooler running to the inlet of the aftermarket cooler. If anything, this should keep the fluid cooler than putting the sensor after the aftermarket cooler.

Picture not included in this copy

Picture not included in this copy

I'm going to wrap the sensor with some of the fiberglass reflective tape provided with the turbo kit. The sensor is about an inch away from the lower rad hose, which probably wouldn't be an issue, but I'll play it safe.

Picture not included in this copy
tmontagueCaledonia Ont. · May 13, 2019#173
Originally Posted by 06YarisRS ↑
Trans thermostat and plumbing done
The sensor is installed on the outlet of the factory in-rad cooler running to the inlet of the aftermarket cooler. If anything, this should keep the fluid cooler than putting the sensor after the aftermarket cooler.
Do you by any chance know what the factory optimal trans temp is? The reason I ask is because with the thermostat installed before the aftermarket cooler is potentially could be keeping the fan on constantly if your thermostat is a low temp set point than what the factory rad cooler typically keeps it at.

It might be a wash either way but I just figured less time the fan is running, less electrical load and stress to the fan.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 13, 2019#174
Not sure of the optimal spec but testing procedures are something like the 124 - 178 range. I thought about it a lot and Derale recommends putting the thermostat where I did - before the aftermarket cooler. If the fan runs too much, I'll swap it to the other line. Since the rad likely hovers around 180+, it may well make the fan run too much. I believe the thermostat kicks in at 180 and out at 165, but I'm not sure if the in-rad cooler would bring the fluid up to 180 or not. I guess only time will tell.

Not sure what you mean that it might be a wash. Do you mean that you think it might not be effective at all? The way I look at it, any additional cooling has got to help.

Thanks.
tmontagueCaledonia Ont. · May 13, 2019#175
Originally Posted by 06YarisRS ↑
Not sure of the optimal spec but testing procedures are something like the 124 - 178 range. I thought about it a lot and Derale recommends putting the thermostat where I did - before the aftermarket cooler. If the fan runs too much, I'll swap it to the other line. Since the rad likely hovers around 180+, it may well make the fan run too much. I believe the thermostat kicks in at 180 and out at 165, but I'm not sure if the in-rad cooler would bring the fluid up to 180 or not. I guess only time will tell.

Not sure what you mean that it might be a wash. Do you mean that you think it might not be effective at all? The way I look at it, any additional cooling has got to help.

Thanks.
I was referring to having the thermostat placed downstream vs upstream may be a wash. No doubt an additional cooler will help.

I'm just thinking that the outflow of trans fluid from the rad will almost never be below 165 (in the middle of summer) and the fan will be constantly running. But that is just my speculation based off of what coolant temps in the middle of summer.

That said, this is new territory for me so what others recommend who have been down that road would be best practice
06YarisRSThread starterFredericton, New Brunswick, Canada · May 14, 2019#176
Originally Posted by tmontague ↑
I was referring to having the thermostat placed downstream vs upstream may be a wash. No doubt an additional cooler will help.

I'm just thinking that the outflow of trans fluid from the rad will almost never be below 165 (in the middle of summer) and the fan will be constantly running. But that is just my speculation based off of what coolant temps in the middle of summer.

That said, this is new territory for me so what others recommend who have been down that road would be best practice
Indeed, it will be an experiment. Below is a pic of my Torque Pro in my van and trans temps are always below oil and coolant. This was after about 45 minutes driving and just before the pic, I had been driving around town. I also found this in a couple previous vehicles I owned in which I had installed trans temp gauges. I don't know if the Yaris is the same. I am hoping that the fluid in the Yaris doesn't run near or over 165 regularly with the additional cooler. If I do find that the fan is running too much, I will move it to the line after the aftermarket cooler. I'm likely going to install a temp gauge as well, so that will help to assess the situation. But, for sure, if the fan runs constantly, then that's no good.

Picture not included in this copy
tmontagueCaledonia Ont. · May 14, 2019#177
hmm, I guess the factory cooler does a better job than I assumed it would. It will be interesting to see what you notice once you have it all running in regards to temps
06YarisRSThread starterFredericton, New Brunswick, Canada · May 14, 2019#178
Originally Posted by tmontague ↑
hmm, I guess the factory cooler does a better job than I assumed it would. It will be interesting to see what you notice once you have it all running in regards to temps
Yes, it would seem it does a good job of cooling the fluid. It would be great if the fan wasn't needed at all, but I expect it will be, especially in bumper to bumper traffic in summer or when I load it beyond factory specs. I've seen my van's aft reach close to 200 creeping along the 401 in summertime. Driving around town with lots of stops and starts, in the heat of summer, will put it in the 170 - 180 range generally.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 14, 2019#179
Passenger side plumbing finally done

I had to order two different silicone couplers and modify the piece of piping that came with the kit. Although it looks tight, it's not touching anywhere. 90% of any flexing will be on the section of coupler that connects the portion of the charge pipe that's bolted to the engine and the intercooler coupler. There is also a coupler that joins the engine charge pipes that is quite flexible too despite being bolted to the A/C compressor. I rocked the engine back and forth (torque/rear engine mount is still not tightened down) and there is no movement or contact of couplers or piping on any chassis parts. Again, flexing is confined to the couplers that basically join the chassis and engine mounted charge piping parts.

Picture not included in this copy

My ATF cooler outlet hose is slightly touching the intercooler coupler, not even enough to deform the circumference of the hose. However, I have discovered that I can pick up a transmission return line from a 1992 - 1997 Jeep Wrangler or Grand Cherokee (or Dorman P/N# 624-384) that will work in this application. It's a very short, 3/8" elbow that should redirect the piping immediately after leaving the cooler so that it doesn't make contact with the intercooler coupler. A local scrapyard has a few of these vehicles and they told me I was welcome to go into the yard and help myself, if I can find one.

Picture not included in this copy

Final result. I did have to use one traditional hose clamp as opposed to a "T" clamp on the curved section of pipe. I did this because I needed a narrower clamp as I had to cut the pipe close to the curve. I did get a great bead roll on it and the clamp cranked down nicely on the right side of the bead roll. Would I want to put 35 psi through this piping? Probably not, but it will easily handle the 7 - 8 psi I'll be feeding it.

Picture not included in this copy

All of the piping is done with the exception of securing the 3" intake piping to the back of the valve cover. That will be done tomorrow hopefully. Then, the vacuum hosing and trans fan wiring will be completed. I'll be into the F/IC wiring by mid next week if things go as planned.
tmontagueCaledonia Ont. · May 15, 2019#180
looks good and seems you have it all well sorted in terms of potential hose leaks due to abrasion.

I'm looking forward to the F/I/C wiring and your thoughts on that as well as the tuners thoughts on it. Good work!
06YarisRSThread starterFredericton, New Brunswick, Canada · May 15, 2019#181
Originally Posted by tmontague ↑
looks good and seems you have it all well sorted in terms of potential hose leaks due to abrasion.

I'm looking forward to the F/I/C wiring and your thoughts on that as well as the tuners thoughts on it. Good work!
Thanks. Yeah, there are a lot of potential leak points in a project of this nature: coolant, oil, water etc. Fingers are crossed, lol.

I too am eagerly anticipating the F/IC wiring outcome.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 15, 2019#182
Started the trans fan wiring

I only had about a half hour to work on the car tonight, but I got the wiring test routed and measured. I'm going to run two extra wires through the conduit; one for a future trans temp gauge and an oil temp gauge sensors. I've already talked about the trans temp hook up plans, but the oil gauge will be pan via the drain plug. I found a nifty 12M x 1.25 to 1.8" NPT fitting that comes with a copper crush washer. I just remove the oil plug, put the sensor in the fitting and screw it in like a normal drain pan bolt. Although the pan is probably not the best spot to monitor, this is without a doubt the simplest route. The oil from the turbo return line comes out close to where the sensor sits, so the reading may be close to indicative of one of the hottest parts of the lubrication system. I may not do these two gauges right away, but I've got all the fittings for both and will have the necessary wires in position when the time comes.

A little preliminary wiring. I'm using 14 gauge stranded automotive primary wire. It's very heavy, solid wire and my run will only be about 3' long and fan amp draw is around 8 amps, so well within safety margins. I remove the plastic terminal protectors, crimp, solder and heat shrink terminal ends and braid, solder and heat shrink all inline connections. I used good quality heat shrink; the kind that oozes out a nice gooey, glue-like substance that really seals well. All wires will run through loom and be completely taped. No moisture getting in here, lol. The loom will be ziptied to the chassis along the way.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
myfirstyotaToronto Canada · May 16, 2019#183
Originally Posted by 06YarisRS ↑
Started the trans fan wiring

I only had about a half hour to work on the car tonight, but I got the wiring test routed and measured. I'm going to run two extra wires through the conduit; one for a future trans temp gauge and an oil temp gauge sensors. I've already talked about the trans temp hook up plans, but the oil gauge will be pan via the drain plug. I found a nifty 12M x 1.25 to 1.8" NPT fitting that comes with a copper crush washer. I just remove the oil plug, put the sensor in the fitting and screw it in like a normal drain pan bolt. Although the pan is probably not the best spot to monitor, this is without a doubt the simplest route. The oil from the turbo return line comes out close to where the sensor sits, so the reading may be close to indicative of one of the hottest parts of the lubrication system. I may not do these two gauges right away, but I've got all the fittings for both and will have the necessary wires in position when the time comes.

A little preliminary wiring. I'm using 14 gauge stranded automotive primary wire. It's very heavy, solid wire and my run will only be about 3' long and fan amp draw is around 8 amps, so well within safety margins. I remove the plastic terminal protectors, crimp, solder and heat shrink terminal ends and braid, solder and heat shrink all inline connections. I used good quality heat shrink; the kind that oozes out a nice gooey, glue-like substance that really seals well. All wires will run through loom and be completely taped. No moisture getting in here, lol. The loom will be ziptied to the chassis along the way.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
I've made the mistake of trusting the plastic insulators on crimp connectors. Long story short I almost burned my car down. Solder and shrink wrap is the way to go.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 16, 2019#184
Originally Posted by myfirstyota ↑
I've made the mistake of trusting the plastic insulators on crimp connectors. Long story short I almost burned my car down. Solder and shrink wrap is the way to go.
Absolutely! They're little water traps too.

Edit: Haha, I see I actually left one of the insulators on my ground. Will have to redo that connection. This circuit will likely max out around 8 amps, so maybe I'll pack it with something to keep the water out.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 16, 2019#185
A little wiring for the trans fan

I decided to go with a relay since I had one gathering dust on my shelf. Here's a drawing of my wiring schematic.

Picture not included in this copy

And a little more soldering/heat shrinking for the relay ground. I got this attached but no pic.

Picture not included in this copy

Relay mounted. Terminals will also get the soldering and heat shrink. I've got some really big heat shrink, so I'll likely cinch up the split loom that all comes together there.

Picture not included in this copy
myfirstyotaToronto Canada · May 17, 2019#186
Originally Posted by 06YarisRS ↑
A little wiring for the trans fan

I decided to go with a relay since I had one gathering dust on my shelf. Here's a drawing of my wiring schematic.

Picture not included in this copy

And a little more soldering/heat shrinking for the relay ground. I got this attached but no pic.

Picture not included in this copy

Relay mounted. Terminals will also get the soldering and heat shrink. I've got some really big heat shrink, so I'll likely cinch up the split loom that all comes together there.

Picture not included in this copy
One thing I've noticed is these cheap relays (not sure if yours is) don't fair well in the open elements (or the engine bay). I've had a few relay failures that were mounted in the engine bay. I'd look into a waterproof one or slather the bottom of the relay (along the seams) in grease to keep moisture out. Food for thought.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 17, 2019#187
Originally Posted by myfirstyota ↑
One thing I've noticed is these cheap relays (not sure if yours is) don't fair well in the open elements (or the engine bay). I've had a few relay failures that were mounted in the engine bay. I'd look into a waterproof one or slather the bottom of the relay (along the seams) in grease to keep moisture out. Food for thought.
Yes! I was looking it over and it doesn't look waterproof. I did wonder about that. I actually thought about coating the bottom in RTV sealant as it's rated for several hundred degrees. I may just pick up a waterproof one as per your suggestion. It would be a simple, couple minute job to remove this one and install a waterproof one.
tmontagueCaledonia Ont. · May 17, 2019#188
solid electrical work, looking good.

I personally always have used the plastic insulated terminal and only crimp (properly) and then always cover in heat shrink even if it it internal. I have never had an electrical issue due to one of my connections. The key think I think it heat shrinking it so no moisture can get in. I would never just crimp and leave as is. I have used the crazy uber expensive glue like heat shrink from CT and as much as I like it, I find that my large case of various size heat shrink I bought off ebay does a good enough job at completely sealing even though it doesn't ooze out glue. IIRC its the stuff that shrinks down 3+ times its size that has the glue. The cheaper 2:1 shrinking stuff doesn't ooze out as much nor does it become rock hard once shrunk.

Also to add to the discussion, that relay looks like the one I have currently for my dual horn set up. I have mine installed just like yours but on the other side of my engine bay and all I have done it put dielectric grease on the terminals for ease of removing them if needed. In 3 or so years my relay hasn't had an issue. It doesn't get exposed to extreme heat where it is located and it not upside down so no water can pool in it. However, a waterproof relay would be ideal.

I did have an electrical failure last year on my horns and somehow one of the smaller gauge wire had an internal failure and wouldn't send power signal to the horns from the relay. That wire sits right in front of my grill and it exposed to everything bad. I also don't think I put heat shrink on the ring terminal end at the horns. Likely water got in that way and corroded the wire. Oddly enough my multi meter would show continuity through that wire but yet it wouldn't sent power through it...
06YarisRSThread starterFredericton, New Brunswick, Canada · May 17, 2019#189
Originally Posted by tmontague ↑
solid electrical work, looking good.

I personally always have used the plastic insulated terminal and only crimp (properly) and then always cover in heat shrink even if it it internal. I have never had an electrical issue due to one of my connections. The key think I think it heat shrinking it so no moisture can get in. I would never just crimp and leave as is. I have used the crazy uber expensive glue like heat shrink from CT and as much as I like it, I find that my large case of various size heat shrink I bought off ebay does a good enough job at completely sealing even though it doesn't ooze out glue. IIRC its the stuff that shrinks down 3+ times its size that has the glue. The cheaper 2:1 shrinking stuff doesn't ooze out as much nor does it become rock hard once shrunk.

Also to add to the discussion, that relay looks like the one I have currently for my dual horn set up. I have mine installed just like yours but on the other side of my engine bay and all I have done it put dielectric grease on the terminals for ease of removing them if needed. In 3 or so years my relay hasn't had an issue. It doesn't get exposed to extreme heat where it is located and it not upside down so no water can pool in it. However, a waterproof relay would be ideal.

I did have an electrical failure last year on my horns and somehow one of the smaller gauge wire had an internal failure and wouldn't send power signal to the horns from the relay. That wire sits right in front of my grill and it exposed to everything bad. I also don't think I put heat shrink on the ring terminal end at the horns. Likely water got in that way and corroded the wire. Oddly enough my multi meter would show continuity through that wire but yet it wouldn't sent power through it...
Thanks. I called all around and no one was aware of a "waterproof" relay. I was told by all of them that water shouldn't get in, especially if it's in an area doesn't get spray. I was also advised by at least two places to do as you did and use dielectric grease. They said that unless I submerge the relay in water, it should be fine. That said, eBay has many that have a rubber coupler that seals the pins. At least if I have trouble, I'll know where to get one.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 17, 2019#190
Trans Fan Wiring installation started

With a bit of available time tonight I got from the battery to the relay power supply run. It's fused with a 20 amp fuse. It will be tidied up and secured behind the battery, high up so the fuse is accessible.

Picture not included in this copy

It runs behind the battery and down behind the fuse box. A switched wire from the fuse box joins the leg here

Picture not included in this copy

Then, on to the relay. Terminals aren't seated yet, but will be after all wiring/loom is secured. You can see the next leg to the right in the pic. It's just draped over the engine for now.

Picture not included in this copy

The blue wire runs from the sensor back to the relay. The pink/white wire is the switched 12V and runs to the other sensor pin. Finally the black 14 GA wire goes from the relay to the fan +

Picture not included in this copy

I have a good route with lots of attach points; well away from any heat sources and would be chaffing areas.

Picture not included in this copy

Sensor wires ready to go into loom heading toward bottom of engine bay. Fan positive is done.

Picture not included in this copy

Loom traveling across above radiator. Not secured with zip ties yet.

Picture not included in this copy

Final leg of harness going down to sensor.

Picture not included in this copy



Here's a couple for fun. Picked up my valve cover breather. I peeked inside with my borescope to see how well built the filter is.

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 20, 2019#191
Valve Cover Breather Install and Engine Cover Test Fit

The breather I bought will accept either a 3/8" or 1/2" barb. The valve cover hose is about 5/8" ID. I was having difficulty finding a fitting that would reduce down until I remembered the Sharkbite Pex fittings. I picked up a 3/4" x 1/2" Pex reducer coupling and it couldn't have worked better. It's nice and tight, only requiring moderate pressue to insert into the breather and the breather hose. I just need to ziptie the hose to the block as it flops around a bit now.

Picture not included in this copy

Picture not included in this copy


Engine cover test fit. Very happy that nothing interferes with the cover. It fits as though there were no mods done to the car at all. In the interest of tidying up the engine bay, I'm going to hunt for some large split loom for those red amplifier wires. I think it will look a lot better.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 20, 2019#192
Frame Painting Touchups

I've been doing this all throughout the project. I figured while I had all the plastic shrouds off, I'd touch up the frame here and there. These had the occasional spots of surface rust, mainly where the plastic shrouds abrade the paint. I degreased, sanded, degreased and gave several coats of ceramic VHT paint, drying the layers with my heat gun. This stuff is really durable. Once it's cured in a few days, I'll blast it all with Fluid Film and spray the frame insides again with Rust Check red.

Picture not included in this copy

Picture not included in this copy
CrankyOldManWest Michigan · May 21, 2019#193
Awesome work!

I'm regretting not doing something similar with the paint on mine when I did the 2ZR swap. I pulled the bumpers off this weekend to make the clutch replacement easier and it's a mess where the parts didn't get painted during the original factory dip. Any suggestions for fixing moderate surface rust in that area?
06YarisRSThread starterFredericton, New Brunswick, Canada · May 21, 2019#194
Hey Sam. Can you snap a few pics of what you're talking about? I don't imagine it's something a coarse wire wheel, some phosphoric acid (rust converter), primer and paint couldn't take care of.
tmontagueCaledonia Ont. · May 21, 2019#195
Originally Posted by 06YarisRS ↑
Frame Painting Touchups

I've been doing this all throughout the project. I figured while I had all the plastic shrouds off, I'd touch up the frame here and there. These had the occasional spots of surface rust, mainly where the plastic shrouds abrade the paint. I degreased, sanded, degreased and gave several coats of ceramic VHT paint, drying the layers with my heat gun. This stuff is really durable. Once it's cured in a few days, I'll blast it all with Fluid Film and spray the frame insides again with Rust Check red.

Picture not included in this copy

Picture not included in this copy
looks clean.

That breather hose that normally see's vacuum and now is vented to atmosphere do you foresee any issues with that? I've read varying things online about removing the vacuum from breather hoses potentially causing problems in a system designed for vacuum.

That said I would think you should be perfectly fine seeing as that hose is upstream of the TB and therefore doesn't actually see much vacuum at all. It would see minimal vacuum at idle and during WOT there is little vacuum anyways
06YarisRSThread starterFredericton, New Brunswick, Canada · May 21, 2019#196
Originally Posted by tmontague ↑
looks clean.

That breather hose that normally see's vacuum and now is vented to atmosphere do you foresee any issues with that? I've read varying things online about removing the vacuum from breather hoses potentially causing problems in a system designed for vacuum.

That said I would think you should be perfectly fine seeing as that hose is upstream of the TB and therefore doesn't actually see much vacuum at all. It would see minimal vacuum at idle and during WOT there is little vacuum anyways
I wondered about the vacuum too, but am following the advice of the turbokits guys. Since the charge pipe that attaches to the throttlebody doesn't have an inlet, there's no place to reintroduce the unburned gasses. I thought about installing a second catch can and plumbing it back into the pipe just before the throttlebody (like the OEM setup), but then I'd run into problems when boost is present. It would probably require a check valve to keep boost from going back into the engine via the valve cover. I know what vacuum leaks can do and I wouldn't be very happy if my idles is erratic, or high due to a vacuum leak. I hope it works as it's supposed to and the other guy I've been talking to at toyotanation has the same setup and apparently hasn't experienced any issues.

The other thing I had wondered about is the brake booster under boost. I guess there is a check valve in that system that will prevent boost going back to the brake booster.
06YarisRSThread starterFredericton, New Brunswick, Canada · May 22, 2019#197
Vacuum Lines

Started installing the vacuum lines. For my setup I only need to supply vacuum to two locations: the blowoff valve and the AEM F/IC. I already installed the wastegate actuator to wastegate boost hose. I am way short on hose since I'm going to install the F/IC inside the car behind the glovebox. I'll need about a 3 foot piece of vacuum hose to complete this job. All connections will be ziptied or possibly clamped.

First Tee tapped into the vacuum supply from the manifold. I may source some brass tees for the vacuum taps as these plastic ones seem a little flimsy.

Picture not included in this copy

BOV vacuum hose. The wires in the center of the pic will be moved and secured. They are just hanging there now.

Picture not included in this copy

Decided to touch up the wiper tray support. It was fairly rust free, but a few minutes time invested made for good results. It too will be saturated with Fluid Film before the wiper tray is reattached.

Picture not included in this copy

I ordered another -4AN oil supply feed line tonight. The one that came with the kit is about 40" long and would be very difficult to install in my car without coiling it up and risking it scraping on body or engine parts. The one I bought is 24" and should fit perfectly as I did measurements with the 40" hose and marked it to the appropriate length with electrical tape.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · May 23, 2019#198
F/IC Wiring

I started looking at diagrams again tonight in anticipation of wiring the F/IC. Tonight's search was for a switched power source at the ECU for the F/IC power supply. Pin 28 on A21 did indeed prove to be a reliable source. I tested it and it is indeed a switched 12V source. So, that's good. I will find the signal grounds tomorrow. Since this configuration of a 2008 xD ECU, 2011 harness and 2ZR engine is unfamiliar to the turbokits guys and AEM, it will be an experiment for sure.

I had a bit of a scare. I wanted to test my trans fan and relay by crossing the terminals on the trans thermostat sensor. It seemed that my EFI fuse socket (the one that powers the MAF - thanks Trevor for that one - and now also the power supply for the transmission temp thermostat) had lost power. I tested it numerous times and started to get a little depressed. I went back inside and started pouring over the wiring diagrams hoping to find another fuse somewhere that, if blown, would cut the power supply. It turns out that because I still had the right ECU connector (A21) disconnected, the circuit was incomplete. I plugged it back in and voila, power was restored. MAF has switched power and the relay for the fan works great too.

Here is what had me freaked out before I discovered what was wrong.

Picture not included in this copy
tmontagueCaledonia Ont. · May 24, 2019#199
Originally Posted by 06YarisRS ↑
F/IC Wiring

I started looking at diagrams again tonight in anticipation of wiring the F/IC. Tonight's search was for a switched power source at the ECU for the F/IC power supply. Pin 28 on A21 did indeed prove to be a reliable source. I tested it and it is indeed a switched 12V source. So, that's good. I will find the signal grounds tomorrow. Since this configuration of a 2008 xD ECU, 2011 harness and 2ZR engine is unfamiliar to the turbokits guys and AEM, it will be an experiment for sure.

I had a bit of a scare. I wanted to test my trans fan and relay by crossing the terminals on the trans thermostat sensor. It seemed that my EFI fuse socket (the one that powers the MAF - thanks Trevor for that one - and now also the power supply for the transmission temp thermostat) had lost power. I tested it numerous times and started to get a little depressed. I went back inside and started pouring over the wiring diagrams hoping to find another fuse somewhere that, if blown, would cut the power supply. It turns out that because I still had the right ECU connector (A21) disconnected, the circuit was incomplete. I plugged it back in and voila, power was restored. MAF has switched power and the relay for the fan works great too.

Here is what had me freaked out before I discovered what was wrong.

Picture not included in this copy
Glad to hear you found the source of your electrical scare. I've had a few issues like that in the past where it ended up being a simple thing and for a couple hours the panic sets in. Keep the posts coming!
06YarisRSThread starterFredericton, New Brunswick, Canada · May 24, 2019#200
Originally Posted by tmontague ↑
Glad to hear you found the source of your electrical scare. I've had a few issues like that in the past where it ended up being a simple thing and for a couple hours the panic sets in. Keep the posts coming!
Haha, yeah, it had me going for a bit. One thing about doing a build and documenting it, is that you know everything that you've done, so the proposition of fixing something doesn't seem as daunting as if you simply adopted a vehicle with so many mods. Still, though, no doubt I'll be scratching my head when it comes to start-up day and it doesn't start. LOL.