Yarisworld Archive

2ZR Turbo Yaris

561 posts · 343,257 views · page 7 of 12

Replies continued

06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 16, 2019#301
Originally Posted by Leegamer ↑
It's not a turbo build if you don't have at least one major boost leak after putting it all back together.
Amen, Haha!
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 17, 2019#302
Smoke test and shop tidying

Vacuum test revealed no leaks. Yay!

Picture not included in this copy

I opened the valve on the catch can.

Picture not included in this copy

I decided to tackle the mess in the shop.

Picture not included in this copy

Picture not included in this copy
ern-dizCA all day · Jul 17, 2019#303
🙇
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 17, 2019#304
BOOST!

Well, I unexpectedly experienced ~ 4 psi of boost. I was down to an 1/8 of a tank of 87, so I poured in 1L of xylene and a 1/4 oz of atf, just for safety measures. I'll burn the tank down to the blinking light and fill up with 91 before the tune. I wanted to just get into boost 1 - 2 psi to test if I have boost, but the car had other plans. It happened quickly and pulled like a rocket. I didn't have time to clearly see the AFR, but out of the corner of my eye, it looked like it was in the 13s, so I'd say the map is doing its thing. There was no knocking at all. I can only imagine what this thing will do at around 7 - 8 psi.

After driving it a bit, I was able to enter about 1 - 2 pounds of boost in a fairly controlled fashion. It definitely pulls harder than the stock 2ZR even at low boost. It does appear to be not only rpm dependent but throttle position dependent. Boost came on strong a little over 3500 rpm. I hope that the tuner can figure out a way to bring boost on around 3000. From the get-go, I wondered if a T25 turbo would have been a better match for this car. It's smaller and would spool faster. The T28 would provide more power up high in the rpm range and likely not run out of steam well into the redline. In any event, I'll try my darndest to stay out of boost until I get my tune, which is this Saturday at 9:30 am. I'm going to request a conservative tune, but will take his advice. I did tell him that reliability is key and losing a few hp/ftlbs is fine in the interest of longevity.

It was so awesome to hear the BOV, but thankfully it's subtle, just a fairly quiet and quick 'PSST' sound. I imagine it will be a bit louder coming off 7 - 8 psi, but still quiet and sleeper-like. 👏

Loving the gauges too. Oil pressure fluctuates between ~20 at idle to ~ 55 - 60 above 3000 rpm. Oil temps are hanging around 190F and trans temps are ~175F driving the car in a spirited fashion but not beating on it. I'm more confident that the car's cooling system will be more than capable of handling the extra power. I won't be calling for boost for extended periods of time.
CrankyOldManWest Michigan · Jul 18, 2019#305
Congrats!!

1 attachment not included in this copy

ern-dizCA all day · Jul 18, 2019#306
Beyond cool.
MaritimeWoodstock nb · Jul 18, 2019#307
Woot. Good on yah.

Sent from my moto e5 play using Tapatalk
tmontagueCaledonia Ont. · Jul 18, 2019#308
Solid work, very well done
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 18, 2019#309
Thanks gents!

I had a great day toodling around in the car and went for about 140 km drive. I ran the car almost out of gas and filled up with 91before heading out on the highway. The car runs very well but will need some fueling adjustments, especially in deceleration from about 60 km/h down to about 20 km/h as it runs rich in that range. If I pop it into neutral within that range, it will drop to 18.2:1.

Tune is still on for Saturday morning at 9:30. Tomorrow I'm going to recharge my a/c system. I let out a little too much refrigerant as the low side was a bit high due to the rising temps. It's just a few psi too low to cool.
eTiMaGoBangkok, Thailand · Jul 18, 2019#310
Awesome, welcome to the boosted club!
LeegamerAshland, VA · Jul 19, 2019#311
Any chance of dyno vids when you get it tuned?
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 19, 2019#312
Originally Posted by Leegamer ↑
Any chance of dyno vids when you get it tuned?
Of course! My plan is to take some clips. Hopefully I don't capture it self-destructing.
LeegamerAshland, VA · Jul 19, 2019#313
SEND IT! lol
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 19, 2019#314
Originally Posted by Leegamer ↑
SEND IT! lol
You'll get video evidence, no matter the outcome. 😁
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 19, 2019#315
All dressed up for tomorrow's hot date...

It got a bath and a coat of paint sealant. I may get the slightly low hanging exhaust tucked up a bit more. There's lots of clearance, but I'm not liking the look that much, honestly.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
heeroyuy01195Florida · Jul 19, 2019#316
Looking good!
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 20, 2019#317
Dyno Results...

So, I have to say that I'm pretty disappointed, however there is definitely potential for more power. My tuner feels that we can get 180+ whp if the boost will go up to 8 psi The tuner feels that my MAF sensor is hindering my performance somewhat. He has suggested that I speak with AEM and ask them their advice on dealing with it. He feels that a resistor may be necessary as the signal may not be clean which is resulting in both intermittent stumbling at idle. It doesn't do it that often and won;t stall, just a hiccup here and there.

I will say that I was hoping for boost in the lower rpm range, but it doesn't really come on until over 5000K. I also maxed out at around 5 psi. So there are some things to investigate there.

Finally, I have learned that automatic transmissions suck for turbos - at least mine. The car pulls really well in second and third, but will likely never be able to see boost in over drive, unless we can do anything to get the boost started at lower rpms, but that may mean a smaller turbo. My tuner feels that the transmission can definitely handle the power generated by around 8 psi.

Anyway, a few pics, before I show the somewhat diasppointing results. On a positive note, though, the car produced 147 WHP at only 4.3 pounds of boost. Should be able to reach my 180 wheel goal when I hit 8 - 8.5 psi.

Getting ready...

Picture not included in this copy

Big fan. This is before he moved it closer to the car.

Picture not included in this copy

On the 'rolling road'

Picture not included in this copy

And, now, no doubt what anyone interested would really like to see... One run netted 155 wph but I didn;t get a pic of that.

Picture not included in this copy
tmontagueCaledonia Ont. · Jul 20, 2019#318
I wouldn't be too disappointed in those numbers. Keep in mind you never had a baseline dyno performed on that same dyno before hand so you cannot actually say how much you gained form it. I know Armstrong posted dyno results, but that was a different dyno and also he has an M/T. A/T's are known to suck power comparably. Chances are you were not sitting anywhere close to the mid 130's whp that Armstrong had and you still got a decent bump in whp from the Turbo.

You now have a starting point to refer against for the future. I am curious how your Butt dyno will find the new set up as this - albeit subjective - will at least give some reference to how it was before to now.

In all honesty 180whp seems a bit on the high side IMO. That would put your around 210-220 BHP which is pretty steep on 91 Octane and your current set up. I would aim for 150-160 WHP on the high end for a reliable daily driven set up.

Do you have a dyno chart at all, I'm curious to see your area under the curve?
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 20, 2019#319
Thanks Trevor. I really appreciate your positivity. It's definitely more powerful but I have a strange thing going on. When I kick it down, I see 6 - 7 psi for a brief second, then it drops way down to like 1.5 or 2 psi. The tuner used his own method of monitoring boost. I have a couple thoughts. I wonder if my exhaust is too restrictive with the aftermarket scion xD cat welded in causing back pressure that forces the wastegate open. Or, for some other reason my waste gate is opening. The tuner really feels that there's very likely that the MAF is messing things up.

I am going to take the front off the car and this time connect my pressure tester directly to the compressor inlet and at the pipe entering the valve body. Then I'll test the throttle body for leaks itself.

I was really hoping to see some appreciable boost in the lower rpms, like around 3500 or 4000, not just over 5000. Maybe if I still have a leak, and fix it, I'll see some boost sooner. In the meantime, I'll stay out of boost.

All a little disappointing, but I'll forge forth.

Oh, thought I had a dyno sheet in the stuff he emailed me but I don't see it. I'll follow up on that and post.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 20, 2019#320
Trevor, dyno graph, as requested.

I was speaking with my tuner tonight and he said he recalled that I tapped into my vacuum line that has that solenoid in the vacuum line on the upper right side (facing the engine bay from the front) of the engine. He's not familiar with the engine, but wonders if the vacuum supply is being cut off. I'm not so sure that's an issue as my tap into this hose is between the solenoid and the manifold.

Anyway, I'll do a pressure test tomorrow and see if the turbo itself or wastegate has an issue.

This curve is nice and smooth. The first few pulls didn't look like that, trust me. LOL.

Picture not included in this copy
myfirstyotaToronto Canada · Jul 20, 2019#321
Didn't this kit claim 90 whp gains on a corolla? For that to be true, you would have to be putting 50whp down before the turbo! Something's off... you'll get it.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 21, 2019#322
Originally Posted by myfirstyota ↑
Didn't this kit claim 90 whp gains on a corolla? For that to be true, you would have to be putting 50whp down before the turbo! Something's off... you'll get it.
Yeah, something's definitely off since I'm only getting ~5 psi, and not consistently from what I'm experiencing and what Torque is telling me. Could be a leak, wastegate adjustment, vacuum issue, MAF issue and possibly (but hopefully not), a torque management issue. My tuner believes it's 'fixable' and I should see 180 whp once this is sorted. It still doesn't solve the issue of it being an automatic, LOL! Of course, if I could get some boost in the lower rpm range, then it would work better with the auto. Speaking to other guys that have the kit and the turbokits guys, I should be seeing boost come on around 3500, not 5K. Something is letting the boost go, or something is inhibiting it. And, thanks for the encouragement. I need it. LOL

As an aside, I have a lot more faith in what these engines can handle. After two or three pulls, I had to walk down the road because I couldn't stand hearing my baby scream anymore. LOL. The tuner knows his stuff and he said the car handled it easily. The engine coolant, oil temps and trans temps were all well within safe limits. I also have more faith in my trans. That said, I'll probablly take Trevor's advice and have him tune it in a way that's a balance between performance and reliability. Maybe in the 160 - 170 range.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 21, 2019#323
Yaris vacuum system experts, help needed...

I started looking into the way I have my vacuum lines hooked up. Please see pics.I hooked up a low air pressure source to the current setup I have and I could hear air leaking and a strong smell of gas and it would not hold pressure. I don't know if this solenoid (vapour canister purge valve solenoid?) closes when the car is running but it's definitely leaking with my current vacuum line setup and the car not running. Maybe this solenoid only works for vacuum and not boost and maybe I'm getting a boost leak because of this. It air leak does not sound like it's coming from the throttle body, but down below the firewall somewhere. I disconnected that connection at the solenoid and supplied pressured air to the tee, so it's pressurizing to the FIC map sensor and the BOV. It's held a steady 10 psi for a long time. Again, I'm not sure what that solenoid does but it definitely seems to be connected to the fuel system. I am going to try to splice into my brake booster line. Thoughts?

Picture not included in this copy

A close up...

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 21, 2019#324
Vacuum from brake booster

My first attempt to solve my boost issue is to restore the original vacuum line that I tapped into, then tap into the brake booster line.

The hose I have is too weak to withstand vacuum and would collapse, so I lined it with some of the very stiff compressor hose I had. It fits perfectly and you can't compress it at all now.

Picture not included in this copy

returned to stock

Picture not included in this copy

New tapping of the brake booster hose. I just have to pick up a couple reducing couplers tomorrow. The hose ends will be trimmed to the right length and then connected. I have enough length on all the hoses to tuck this all away nicely and protect it from chafing. Of course the tubing will be fully seated on the tee when I put it back together.

Picture not included in this copy
ern-dizCA all day · Jul 22, 2019#325
My, oh my, you've been busy! I'm nowhere near as knowledgeable, but like Trevor, I wouldn't say disappointed. A lot of positives here and you're working towards sorting things that need sorting. You, sir, are kicking much ass.
LeegamerAshland, VA · Jul 22, 2019#326
Pretty surprised at that boost lag, seems like it would be a reasonable turbo to run for that motor to get a good range of boost.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 22, 2019#327
Originally Posted by ern-diz ↑
My, oh my, you've been busy! I'm nowhere near as knowledgeable, but like Trevor, I wouldn't say disappointed. A lot of positives here and you're working towards sorting things that need sorting. You, sir, are kicking much ass.
Thanks ern-diz! I always appreciate your encouragement. I'll have an update shortly.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 22, 2019#328
Progress

Well, I found a T-clamp that wasn't as tight as the others. It is the clamp that connects the first section of the charge piping to the compressor outlet. I cranked it down quite hard and then went for a drive. It pulls like crazy; much than when I brought it back from the tuner and I can hear my BOV when I release the throttle everytime after going into boost. I wasn't hearing it before. Torque shows the boost initially at 2.9 psi, then it goes into vacuum, but AFAIK, you don't hear a BOV in vacuum. This would also explain my dyno chart and the fact that my tuner was seeing 5.4 psi. I may need to procure a dedicated boost gauge. Also, boost seems to come on much sooner, probaby closer to 3500 - 3700 rpm. I plan to go for a drive later and I'll bring the laptop along and I can monitor PSIA load which will tell me the actual boost above atmospheric pressure. I just have to subtract 14.7 (I actually live probably 30 feet above sea level)

However, I still have idle issues to work out and I have some occasional light bucking and a misfire code P0303 (cylinder 3). The bucking occurs when I am out of boost at about 120 km/h on a hill at light to moderate throttle. I press down a bit harder on the throtte, the bucking stops. I think I need to do some road tuning and add some fuel in the cells that correspond to that particular load and RPM.

So, I'm very happy that I am seeing progress, but there are issues to deal with yet. I will take a few degrees of timing at idle to smooth that out, add some fuel for the bucking and report. I'm going to speak to my tuner and see if he'll give me 30 - 60 minutes of road tuning as opposed to getting on the dyno again.

If I had to guess what I'm producing at the wheels now, I would say closer to 170 - 180 - but that's butt dyno only, of course.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 22, 2019#329
Originally Posted by Leegamer ↑
Pretty surprised at that boost lag, seems like it would be a reasonable turbo to run for that motor to get a good range of boost.
Yes, for sure. Check out my post just above.
heeroyuy01195Florida · Jul 23, 2019#330
Can you describe the idle issues and the bucking a bit more? Glad you found the source of the leak! I would definitely invest in boost gauge to keep an eye on things.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 23, 2019#331
Originally Posted by heeroyuy01195 ↑
Can you describe the idle issues and the bucking a bit more? Glad you found the source of the leak! I would definitely invest in boost gauge to keep an eye on things.
Sure can.

Idle:

Idle is perfect and smooth (around 750 rpm) when the car is below operating temps. It is always hard to start. It takes a few cranks and often requires messaging the throttle in the first few seconds to keep it running. Usually two or three light shots of gas will get it over this hump. My suspicion is that it's very rich at startup - but I could be wrong. Then it settles out into a nice idle. Once it's up to operating temps at idle in neutral or "D", it will intermittently feel like it is going to stall (rpms drop quickly but only for a fraction of a second), then immediately recovers. This intermittent stumbling only happens at idle and occurs every minute or two and sometimes every few minutes. By this time the idle is around 550 - 600 rpm (a bit slow). If I turn my A/C on at this point and put it in drive, it may stall, but not always. Under these conditions it has stalled in reverse as I believe that puts more load on the engine. Before I installed the 440cc injectors, I had no idle issues whatsoever, and it literally ran like stock at idle. I really need to get this issue resolved because it's dangerous at intersections etc in the city as the car might stall when approaching or stopped at a stop sign/light. Then, of course I lose power steering assist and possibly some braking.

Bucking (this did not happen at all before my tune):

If I am driving on the highway at around 110 - 120 km/h under light throttle and encounter a slight grade, the car will start to buck a bit (seems like misfire, which would corroborate the P0303 code). If I apply even the slightest extra throttle when the 'misfire' is occuring, it will completely stop the hesitation and run perfectly.

I plan to do some data logging with the F/IC software. I'll also monitor the fuel cell data while I recreate the 'misfiring'. My tuner said that I would probably have to add some fuel at those points.

Rich AFR:

90% of the time the car runs at, or close to stoich - except of course in boost when the AFR richens purposefully. When I am decelating (basically with my foot just resting on the pedal at low speeds - or to maintain low speeds speed - say coming down from 60 km/h), the AFRs may jump up as high as the high 12s, but most often something like 13.4 - 13.8. Under these conditions, there is no difference in how the engine performs, sounds or feels. If I just tap and release the throttle under this light deceleration, the AFRs will drop to the expected 18.12.

Overall, the car must be running rich as I have black soot in the tail pipe. And, maybe my misfire is related to plug fouling, but not sure about that as the misfiring occurs only under very specific conditions as mentioned in the first paragraph.

A local parts store has a vacuum gauge that can go up to +10 psi. I'm grabbing that today, plumbing into my vacuum lines, running the tubing through my window and will see what it tells me.

MAF:

I can monitor MAF voltages in the F/IC software. It will you show you MAF input and MAF output voltages. It does look like the F/IC is adjusting the voltages as there are subtle differences between the input and out voltages. I am wating to hear back from AEM as to whether the F/IC seeing the voltages indicates that the MAF wiring is hooked up properly. My tuner does think that the MAF may be messing somewhat with my boost/contributing to my idle issues.

Finally, I have a B1S2 (rear O2 sensor) code (P0137), I believe. I am basically catless as the cat is after the rear O2 sensor. I had them weld the cat in as a 'resonator' of sorts. I've fixed this issue before by adding sparkplug defoulers to get the O2 sensor back out of the exhaust stream a bit. This did not work for this car. Although voltages generally fluctuate between 0.1V and 1.0V, it will occasionally spike above that, which I believe is setting the code. I did read that the rear O2 sensor does influence AFR in this car, so maybe it's related to my issues too. In Torque I can data log, so I'll figure out how to get it to monitor O2 sensor voltage and a couple other paramters at the same time. Maybe it will give me some insight into what's going on. I did fiddle with the fuel map, taking out some fuel at the rich points and it did appropriately affect the AFR, leaning it a bit. But, I'm not sure how this would affect AFRs in the opposite direction - aka, accelerating.

I have asked my tuner if we can do a street tune and he's up for that.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 23, 2019#332
Making progress...

1) Bucking at highway on hills (light to moderate throttle)

As I described, I'm getting a bit of bucking (misfiring?) at around 110 - 120 km/h on hills with moderate throttle. Again, if I add a touch more throttle, or ease off the bucking stops. I connected the laptop, monitored AFRs and found the precise spots where the bucking occurs. So, it appears that between 1.3 - 3.3 pounds of boost, I get the bucking. You can see that this is the point were significantly less fuel is taken away in the interest of becoming more rich as this is the onset of boost. Above that, more fuel is added. This is the tuner's map which is currently the one loaded in the F/IC. I will speak to turbokits.com as they have the same cell values in the table.

Picture not included in this copy

2) Boost

Monitoring my MAP from the F/IC software, I am definitely getting boost and it starts below 3000 rpm. I have seen as high as ~21 PSIA - around 6 psi boost - but I wasn't full throttle with pedal to the boards. It's difficult to monitor it with the laptop on the passenger seat while driving, so I picked up some stuff today to monitor my boost directly. For now, I will run the tubing through the firewall as I expect I'll end up getting an actual boost gauge.

Picture not included in this copy
tmontagueCaledonia Ont. · Jul 23, 2019#333
You are definitely correct about the newer smart ecu's and the 2ndary O2 sensor influencing AFR's. I put 2 defoulders in my outback for a p0420 code and I ended getting 2 other O2 sensor codes showing delay in reading and low voltage. I could see the voltages between the bank 1 and 2 sensors with my ultra gauge during driving. It essentially caused it to read very delayed and read lean. I removed it due to this.

Earlier 1st gen ecu's the 2ndary O2 sensor was only for emissions and did not influence AFR's.

Good job trouble shooting so far. I was surprised that you weren't getting boost until 5k rpm, do I'm glad you found the issue
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 23, 2019#334
Originally Posted by tmontague ↑
You are definitely correct about the newer smart ecu's and the 2ndary O2 sensor influencing AFR's. I put 2 defoulders in my outback for a p0420 code and I ended getting 2 other O2 sensor codes showing delay in reading and low voltage. I could see the voltages between the bank 1 and 2 sensors with my ultra gauge during driving. It essentially caused it to read very delayed and read lean. I removed it due to this.

Earlier 1st gen ecu's the 2ndary O2 sensor was only for emissions and did not influence AFR's.

Good job trouble shooting so far. I was surprised that you weren't getting boost until 5k rpm, do I'm glad you found the issue
Interesting stuff. I was checking out my O2 voltages today for the B1S2 sensor and it stayed at 0 regardless of throttle input, rpms etc. I thought, that's weird. I'm pretty sure a cooked the leads as I had temporarily hooked it up and it was fairly close to the exhaust. I'm going under the car in bit and will confirm if indeed it's shot. I have another O2 sensor I bought a while ago, so I'll pop that on after extending the harness. I'm still have to reinstall my heat shield, so I'll run the wire up and over that. That should keep it safely away from the heat.
LeegamerAshland, VA · Jul 23, 2019#335
So glad you found the boost leak. That's awesome.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 23, 2019#336
Boost test with gauge

So, I tapped into the MAF line to the F/IC to test my boost using the gauge I picked up. I am definitely getting boost in the lower rpms ~ 2800. If I mash the throttle in third the boost shoots up to 4.5 and tops out. I had a couple of thoughts:

1) the vacuum hoses that connect to both the throttlebody and manifold are held on by pretty flimsy spring clamps. These are certainly not designed to experience positive pressure, only vacuum. I can actually turn the hoses and could easily pull them off with the spring clamps on. I am going to pick up some screw pipe clamps and tighten those down. There are about 6 connection points that I think have the potential to leak.

2) Manifold and throttlebody gaskets. Since it's impractical to pressure test the manifold or throttlebody, I think I may go ahead and order a gasket for each. In both the process of the engine swap and during the turbo build, I removed both items. It's possible they are leaking. I think leaks in these areas would also contribute to my idling issues.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 23, 2019#337
Originally Posted by Leegamer ↑
So glad you found the boost leak. That's awesome.
Well, I did but there may be more areas to deal with. See above.
WeeYariGeorgetown, Ontario, Canada · Jul 23, 2019#338
Originally Posted by 06YarisRS ↑
Well, I did but there may be more areas to deal with. See above.
The BUG plus is you actually got boost down into the usable rpm range.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 23, 2019#339
Originally Posted by WeeYari ↑
The BUG plus is you actually got boost down into the usable rpm range.
Oh, for sure, WeeYari! I was so happy to see that. Now 1 - 2 psi doesn't make a huge difference, but it's definitely pulling harder. At 4 psi it's pretty strong. Once I get to my full 8, it should be even more fun!

I found this calculator a long time ago and just recently started plugging numbers in again. It is a simplified calculator, but a good reference anyway. It also seems right in line with my dyno results. Ultimately, I don't care what my numbers are as long it's working to its potential and is safe.

My Corolla engine should put out 126 crank HP stock, due to the xD (detuned, I think) ECU. With a 15% (the average, I guess) driveline loss, that would result in about 107 whp. Assuming 5.4 psi (which the tuner got, not sure how, lol), that equates to 146.32 whp. That's bang on with my dyno numbers.

At 8 psi, I should be able to expect ~165 whp. I think that should suffice in the light little Yaris, haha.

I had a long chat with a member of Toyota Nation a couple of evenings ago. He has the same kit and apparently he dyno'd 195. The kit claims to add 90 - 100 hp to the Corolla, so not sure what all is at work with mine.

Anyway, here's the very simplified boost calculator:

http://www.wallaceracing.com/hp-blower.php

It's important for me to keep my expectations in check and understand fully what this is. I've driven in muscle cars and a friend had a Porsche 930 turbo that was an under 5 second 0 - 60 car. The turbo Yaris will never be this, but it will be very fun to drive.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 23, 2019#340
leak-proofing vacuum lines

Just to be sure that I have no leaks, I'm clamping every connection. The OE vacuum lines are held on with spring clamps. You can actually turn the hoses and pull them straight off without removing the clamps. Since these are designed to see vacuum only, I thought I'd 'boost-proof' them just in case I'm losing a bit of boost through these connections.

The OE (larger) hoses are now all screw clamped, much tighter and cannot be rotated or even budged. I read on a turbo forum that zipties are great for securing turbo vacuum tubing, so I did that to all of the connections I made when installing the turbo vacuum lines.

Picture not included in this copy

I will be re-checking all of my T-clamps as well. Starting with the throttle body clamp, I noticed that the clamp seems a bit too wide to sit flush to the throttlebody. There is a raised section in the casting at the back of the throttle body that prevents the wide clamp from seating all the way back. The clamp may have been riding up a bit on the throttlebody inlet flare. I trimmed off a bit of the metal on the clamp. The clamp now fits more securely and is just behind the flare. I don't know that it was leaking, but the clamp is seated much better now.

Picture not included in this copy

I just want to rule out boost leaks before looking into possible ECU management issues that may be thwarting my full boost.

I have also decided to buy a high flow CAT with O2 sensor bung. I can get a stainless steel one with bung on eBay for about $45.00. I might be able to get away without my defoulers if I install the high flow CAT, and be rid of the annoting P0137 code. I'll just cut my pipe with my sawzall, and clamp the CAT into the straight section.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 24, 2019#341
Stuttering/ bucking at low boost

I've been doing some research on my bucking issue at moderate throttle between 1 and 3 psi. I compared the tuner's map and the basemap for TK. The fuel cell values in that area of the maps are identical, so not sure what's causing that since it started doing it after my tune. The tuner recommends adding some fuel in those cells. I"ll test drive, replicating the stuttering and monitor my AFRs. If lean, I'll add some fuel. The research I did suggests a couple possibilities. 1) radical changes in adjacent cells can cause bucking at certain loads, or 2) I need to wire in parallel a 2.2K ohm resistor between the crank mag wires. Apparently several turboed Scion cars have this issue. Boomslang started adding these resistors to there PnP harnesses around 2007. I have a 2008 Scion ECU.I've been doing some research on my bucking issue at moderate throttle between 1 and 3 psi. I compared the tuner's map and the basemap for TK. The fuel cell values in that area of the maps are identical, so not sure what's causing that since it started doing it after my tune. The tuner recommends adding some fuel in those cells. I"ll test drive, replicating the stuttering and monitor my AFRs. If lean, I'll add some fuel. The research I did suggests a couple possibilities. 1) radical changes in adjacent cells can cause bucking at certain loads, or 2) I need to wire in parallel a 2.2K ohm resistor between the crank mag wires. Apparently several turboed Scion cars have this issue. Boomslang started adding these resistors to there PnP harnesses around 2007. I have a 2008 Scion ECU.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 24, 2019#342
Stuttering/ bucking at low boost

I've been doing some research on my bucking issue at moderate throttle between 1 and 3 psi. I compared the tuner's map and the basemap for TK. The fuel cell values in that area of the maps are identical, so not sure what's causing that since it started doing it after my tune. The tuner recommends adding some fuel in those cells. I"ll test drive, replicating the stuttering and monitor my AFRs. If lean, I'll add some fuel. The research I did suggests a couple possibilities. 1) radical changes in adjacent cells can cause bucking at certain loads, or 2) I need to wire in parallel a 2.2K ohm resistor between the crank mag wires. Apparently several turboed Scion cars have this issue. Boomslang started adding these resistors to there PnP harnesses around 2007. I have a 2008 Scion ECU.
CrankyOldManWest Michigan · Jul 24, 2019#343
Oh man, I can hardly wait to see what happens when you've got it all sorted out! I remember the change from the stock 1.5 to the supercharger and also to the 1.8 being some next level stuff. Going from the stock 1.8 to boost will be insane, even at 160-170 whp.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 24, 2019#344
Originally Posted by CrankyOldMan ↑
Oh man, I can hardly wait to see what happens when you've got it all sorted out! I remember the change from the stock 1.5 to the supercharger and also to the 1.8 being some next level stuff. Going from the stock 1.8 to boost will be insane, even at 160-170 whp.
Thanks Sam. I'll tell you right now that this car is already insane even at 4 psi. I was out today data logging and adjusting fueling to combat the studder I'm getting at part throttle. Check out my next post for some new info.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 24, 2019#345
More updates...

So, I was out datalogging today. I'll review those in a bit.

I have almost erradicated my stumble at part throttle at around 3100 rpm. I have been adding fuel to the cells which are highlighted when the car bucks. I still have one small buck to eliminate. Fortunately we have a good stretch of highway with hills, but it's still a challenge to drive, hold rpm and edit the table simultaneously. I don't really have anyone that could either drive - the way I need the car driven - or that could make the changes in the software. I'm going out again this afternoon, to kill - I hope - once and for all, the last stumble. It is a tricky process as when you make a change in one cell, the stumble might suddenly shift to the area represented by another cell (aka, different rpm and load). My fuel table looks crazy with fuel added and in many cells and radical shifts from once cell to the adjacent ones, so I'll be closely monitoring my AFRs to be sure I don't have any dangerous lean spots. I don't expect to as all I've been doing is adding fuel. AFRs where I've made the changes look good. That said, I'm going to confirm this with turbokits and my tuner before I go blasting around in boost.

The best news...I think...

For the first time today, I was driving around with my window open. As I enter boost, I can hear air hissing from the driver's side quarter panel. As the boost increases (and maxes at around 4 psi), the hissing gets louder, then my BOV releases when I come off the throttle. I HAVE ANOTHER BOOST LEAK! I think, or a vacuum line leak that's not keeping the BOV fully shut under boost. This is looking very promising. If I get this fixed (I'm still in the process of adding clamps to vacuum lines and will recheck all my T-clamps, I expect I'll see my full boost.

I will say that the car is positively nasty already at 4 psi. It pulls very hard and the wheel(s) (just one as I have no LSD) wants to spin at speeds over 30 - 40, km/h when it downshifts in boost, and I'm on a hill for example. I did, for the first time enter moderate boost (maybe 3 psi, moderate given my current max boost) in 2nd gear and it chirped the tires shifting to 3rd. I was really surprised. Honestly, I'm quite afraid of what this car will be capable of at 8 psi.
CrankyOldManWest Michigan · Jul 24, 2019#346
Originally Posted by 06YarisRS ↑
More updates...I will say that the car is positively nasty already at 4 psi. It pulls very hard and the wheel(s) (just one as I have no LSD) wants to spin at speeds over 30 - 40, km/h when it downshifts in boost, and I'm on a hill for example. I did, for the first time enter moderate boost (maybe 3 psi, moderate given my current max boost) in 2nd gear and it chirped the tires shifting to 3rd. I was really surprised. Honestly, I quite afraid of what this car will be capable of at 8 psi.
Sounds like you're ready for a MT swap!
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 24, 2019#347
Originally Posted by CrankyOldMan ↑
Sounds like you're ready for a MT swap!
I woud love to have Tom's 6-speed, LSD and all the goodies for the swap! Now, wouldn't that spice up my Yaris! Haha.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 24, 2019#348
Bubbles

As I mentioned earlier, I could hear a significant air leak coming from my driver's quarter panel area when I entered boost. It got louder the farther I went into boost. I think I got lucky and stumbled on the right combination of factors: I had my window down and I was test driving on a back road, so sounds were bouncing back off the trees. Otherwise I might not have even heard the leak.

So... I conducted more testing.

Using my mini compressor, I repeated my charge pipe pressure test. As before, it held 20 psi with ease and there were no leaks - the gauge stayed dead at 20. This is with the BOV removed and the port capped off.

Then I tested my vacuum/boost line that runs from the FIC MAP sensor to the BOV and gets its vacuum source from the brake booster line. The vacuum lines held 20 psi, no leaking, gauge didn't move.

So, we've established that there are no vacuum leaks, nor charge pipe leaks.

Finally, I reinstalled the BOV and tee'd off my compressor line so I could pressurize both the vacuum lines and the charge piping - simulating a manifold pressure boost situation. Unless, I'm doing something wrong (highly probable) or am not understanding fully how the system works (again, highly probable), I think my BOV is faulty. With both sides of the BOV pressurized, I have a significant leak with air bleeding from the BOV, until - guess when? - the pressure lowers to a little less than 5 psi and the gauge stays put. Hmmm... ~ 4 psi is the max boost I'm getting. I can't think of anything else, but it does really seem like I'm losing my boost - or not able to get to full boost - due to a leaking BOV. I passed this all by my tuner and he's pretty sure I've diagnosed this correctly. I've emailed the turbokits guys and I'm sure they'll have an answer for me. They are very attentative and bang on when it comes to support.

New testing apparatus

Picture not included in this copy

One hose from the compressor, one hose to the BOV and one hose to the F/IC MAP sensor

Picture not included in this copy

Lots of gushing air and bubbles with the BOV pressurized from both sides. The air is coming from the holes in the BOV, not my coupler/clamps.

Picture not included in this copy

Here's a pic of the schematic of my testing precedure:

Picture not included in this copy


On a positive note, I have pretty much erradicated my partial load stumbling at highway speeds. I did this by adding fuel in the active cells of the map where the stumbling occured. I still have one hiccup but could't get to it as my laptop battery died before I could eliminate that one. The changes have made for a pretty funky looking fuel map, but my tuner tells me that it is so vehicle dependent and that tuning it to address driveability issues is what's needed. He launched into a detailed explanation of closed loop vs open loop transitions, kilopascals and all kinds of other stuff that flew over my head. However, he says that many cars he's tuned have maps that are all over the place and that's perfectly fine if that's what the car needs. Of course, I do have to watch AFRs as I make changes, but I'm only adding fuel, not subtracting. Again, I'll bounce this off the turbokits guys as they're the experts.
CrankyOldManWest Michigan · Jul 25, 2019#349
Having done zero research myself, I can't verify how accurate the wikipedia article is but it suggests that the MAF vs blowoff issue is fairly common and can be compensated for by placement of the MAF.
06YarisRSThread starterFredericton, New Brunswick, Canada · Jul 25, 2019#350
Originally Posted by CrankyOldMan ↑
Having done zero research myself, I can't verify how accurate the wikipedia article is but it suggests that the MAF vs blowoff issue is fairly common and can be compensated for by placement of the MAF.
Thanks Sam. Great read.

My BOV is before the MAF sensor, so a blow through system as opposed to a drwa through system. The kit, I believe, was designed purposefully as a blow through type. I found the SR20DET example interesting in the respect to the necessary relative position of each piece.

According to my tuner, we are basically trying to get a economy car to perform in ways that it was obviously not intended to and the hard part is reconciling the piggyback's and the ECU's handling of open loop and closed loop operations. I think I'm getting close to a good tune and I asked him if when we achieved a good tune for this car if it would remain stable. He said, "definitely". It will just take tweaking to make it 'perfect'. I'm still having some minor idling issues and overall the car is running a tad rich, evidenced by a bit of soot in the tailpipe. I do want to get this ironed out because not doing so could potentially result in high EGTs and issues with the cat converter. That said, it seems my car is rich only under vacuum conditions and relatively low power demands, so excess heat may not be an issue. I'll keep tweaking the fuel map.

Thanks again for the article!