It is quite big, but should fit. I'm actually happy it's large with good cooling capacity since I'll be drawing intake air from behind the engine. I'll get my tape out tomorrow and get the dimensions of the intercooler.Originally Posted by WeeYari ↑It certainly is!
It looks bigger than specs on the site. Must be skinny plank flooring that it is resting on.
Sent from my EML-L09 using Tapatalk
2ZR Turbo Yaris
561 posts · 343,257 views · page 2 of 12
Replies continued
Well, as cold as it is, I went out tonight for about a half hour to start my attack plan. I soaked all the manifold stud/nuts and exhaust shield components with Releasall. Removing the exhaust shield and manifold support and manifold may have to happen from both the top and the bottom, of course with the hood and wiper cowling removed. Fortunately most of the fasteners aren't rusted badly at all. Some of them are actually rust-free.
I also managed to get the stuck spring bolts at the manifold loosened and backed off. My next trip to the garage and the exhaust piping will be removed and hopefully the manifold.
These nuts should come off fairly easily, but I'll wiggle the nuts back and forth to slowly cut through the rust on the studs.
Picture not included in this copy
That donut looks a bit small to me! I'm amazed there wasn't an exhaust leak. It fit into the midpipe well, so I'm wondering if the Corolla and xD have slightly different manifold flanges. 🤷
Picture not included in this copy
I also managed to get the stuck spring bolts at the manifold loosened and backed off. My next trip to the garage and the exhaust piping will be removed and hopefully the manifold.
These nuts should come off fairly easily, but I'll wiggle the nuts back and forth to slowly cut through the rust on the studs.
Picture not included in this copy
That donut looks a bit small to me! I'm amazed there wasn't an exhaust leak. It fit into the midpipe well, so I'm wondering if the Corolla and xD have slightly different manifold flanges. 🤷
Picture not included in this copy
Behind the engine? What intercooler set.up are you doing?Originally Posted by 06YarisRS ↑It is quite big, but should fit. I'm actually happy it's large with good cooling capacity since I'll be drawing intake air from behind the engine. I'll get my tape out tomorrow and get the dimensions of the intercooler.
I wasn't very clear. When I said "intake air", I meant for the turbo compressor. It's front mount intercooler but the turbo compressor air intake will just be the K&N filter attached directly to the turbo, no cold air intake. I spoke with the guys at TK and the cold air intake - that comes back up from behind the engine and wraps around, placing the filter basically between the engine and battery - is an option. They claim there are many cars with the kit that don't have the cold air intake. The large intercooler looks after any additional heat in the charge piping that might picked up behind the engine. Ultimately, I may come up with my own custom cold air intake. Although theirs is $195.00, it still lands the filter smack dab in the engine bay and up top where the hot air is. If it went somewhere where it could draw colder air, I probably would have bought it. I suppose I could have bought it, another bit of pipe and a coupler and directed it closer to the headlight where the stock airbox is. May do that yet.Originally Posted by tmontague ↑Behind the engine? What intercooler set.up are you doing?
Good start, taking the manifold off to do anything there is always the risk of a broken stud, and as they say, any half hour project is 1 broken bolt away from a 3 day ordeal. may that not happen here.
Hmm, hood scoop in the near future?😉
+1, a functional scoop may be perfect.
Would be uber cool. When I was musing about a custom setup, I thought briefly about a TMIC and hood scoop. I actually saw a carbon fiber hood with molded hood scoop that looked awesome.Originally Posted by tmontague ↑Hmm, hood scoop in the near future?😉
You know, since I have a 'paint booth', I suppose if I could find a scoop that suited the car, it wouldn't be that big a job to cut, mount, fill, prime and paint my own custom hood scoop. Then again, it would take away from the 'sleeper' factor. Haha.
Ha, yes, the scoop would announce loudly there are mods to the car. Although most folks would probably laugh, until you blow past at ludicrous speed and hear the woosh of the turbo LOL
LOL...practically anyone I tell that I am turboing my Yaris already laughs. All the more reason for going the sleeper route.Originally Posted by Maritime ↑Ha, yes, the scoop would announce loudly there are mods to the car. Although most folks would probably laugh, until you blow past at ludicrous speed and hear the woosh of the turbo LOL
Sleeper FTW!
Just don't become one of those fools who spool up for the sole purpose of advertising their blow-off.
Sent from my EML-L09 using Tapatalk
Just don't become one of those fools who spool up for the sole purpose of advertising their blow-off.
Sent from my EML-L09 using Tapatalk
Yep, and they are always in a friggin neon or destroyed WRX LOLOriginally Posted by WeeYari ↑Sleeper FTW!
Just don't become one of those fools who spool up for the sole purpose of advertising their blow-off.
Sent from my EML-L09 using Tapatalk
Little worry about that. LOL. Not really my style. An increase in performance is purely for my benefit, no one else's. Well, maybe my son. I'm sure he wouldn't mind the sensation of being pushed back in his seat a wee bit. Ssshhhh... Don't tell mom. 😁Originally Posted by WeeYari ↑Sleeper FTW!
Just don't become one of those fools who spool up for the sole purpose of advertising their blow-off.
Sent from my EML-L09 using Tapatalk
In all honesty, I have no interest in racing anyone. Or, showing off for anyone. I will appreciate a noticeable gain in power whilst marveling at the exquisite engineering of my little turboed car. Secondly, it will be treated with respect, because not doing so would get very expensive, very quickly.
What I might enjoy doing, when the likely occasion presents itself, is pulling away from a redneck or two that like to roll close behind you in their BIG TRUCKS. The expression on their face(s) might be gratifying.
One another note...my latest stressor - to get hung up on - is how my axles will handle the extra torque/power. I think Adam may have mentioned that in a previous post.
Your axles will likely be fine in rolling accelerations. Stay away from dropping the clutch from a stop ( you have an a/t so you can't really do that anyway lol)
With my current set up I never go wot and up to redline in first gear. Partly to protect the drive trading but mainly because with a reduced final drive there is too much torque and it spins track slicks even when they are hot
With my current set up I never go wot and up to redline in first gear. Partly to protect the drive trading but mainly because with a reduced final drive there is too much torque and it spins track slicks even when they are hot
My buddies golf makes 470whp with stock axles. Apparently as the story goes, don't mount slicks and you shouldn't break axles. Tire should spin before axle breaks.
Thanks both of you. That's reassuring about the axles. I doubt that boost in first would make much sense anyway, because with the 2ZR naturally aspirated, it wants to break loose anyway.
Yep I think you'll have more worry about spinning tires and loosing grip long before you break an axle.
Got the midpipe and axleback off.
Tomorrow - time permitting - the wiper cowl and hood will be removed. I am concerned about how to get the OEM manifold out once it's removed from the head. I'm guessing it's going to have to come out the top, or the axle is going to have to be removed. Also, the 2ZR exhaust sits a little to the right of the body channel. Fingers crossed that the 3" downpipe will line up with the channel. I may be in for some modification of the down pipe, but time will tell. Also, the manifold brace and heat shields are going to be no picnic either.
Not much done today, but I only had a half hour or so.
Hoping to clock the turbo tonight if I can get time. If so, I'll post up pics.
Picture not included in this copy
Picture not included in this copy
Tomorrow - time permitting - the wiper cowl and hood will be removed. I am concerned about how to get the OEM manifold out once it's removed from the head. I'm guessing it's going to have to come out the top, or the axle is going to have to be removed. Also, the 2ZR exhaust sits a little to the right of the body channel. Fingers crossed that the 3" downpipe will line up with the channel. I may be in for some modification of the down pipe, but time will tell. Also, the manifold brace and heat shields are going to be no picnic either.
Not much done today, but I only had a half hour or so.
Hoping to clock the turbo tonight if I can get time. If so, I'll post up pics.
Picture not included in this copy
Picture not included in this copy
Anxious to see your downpipe conclusion!
Haha, me too!Originally Posted by myfirstyota ↑Anxious to see your downpipe conclusion!
Sorry about the pic quality, and the mess in the background. My kids got off to bed without doing their cleanup. Daddy was preoccupied. 🙄
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Nice
Sent from my moto e5 play using Tapatalk
Sent from my moto e5 play using Tapatalk
Picture not included in this copy
😁😁😁
Remembuh when I told you I wouldn't turbo my ka?...I lied. (Arnie)
🤣Originally Posted by 06YarisRS ↑Remembuh when I told you I wouldn't turbo my ka?...I lied. (Arnie)
Ha!Originally Posted by 06YarisRS ↑Remembuh when I told you I wouldn't turbo my ka?...I lied. (Arnie)
Hood and wiper cowl removed. Much better access into the back of the engine bay. I got the two top bolts off the upper exhaust shield very easily. The bottom bolts are much more reluctant as they are in fairly large captive nuts. I've soaked them in ReleasAll and will go at them again tomorrow. Getting these shields off and the manifold out, may be one of the tougher parts of this project. I'm still thinking the turbo (without manifold) may not fit in without either dropping the subframe or removing the axle and going infront of the subframe. Hopefully I'll know this weekend.
Picture not included in this copy
On a positive note, I pushed the tunnel heat shield up and I have more space to work with. I may ultimately remove it. I will do measurements of the Yaris tunnel tomorrow. Today, I drove a colleague's 2012 Corolla onto our hoist at the school and took some pics.
Yaris Tunnel:
Picture not included in this copy
Corolla Tunnel - Next 3 images. Measures about 7.5" of clearance from the top of the tunnel to subframe. And close to 8" side to side/
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Attached the fittings (oil supply, oil return, water supply, water return) to the turbo this evening. Just need a couple clamps on the water lines. Fingers crossed that there are no leaks after install.
Picture not included in this copy
Picture not included in this copy
On a positive note, I pushed the tunnel heat shield up and I have more space to work with. I may ultimately remove it. I will do measurements of the Yaris tunnel tomorrow. Today, I drove a colleague's 2012 Corolla onto our hoist at the school and took some pics.
Yaris Tunnel:
Picture not included in this copy
Corolla Tunnel - Next 3 images. Measures about 7.5" of clearance from the top of the tunnel to subframe. And close to 8" side to side/
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Attached the fittings (oil supply, oil return, water supply, water return) to the turbo this evening. Just need a couple clamps on the water lines. Fingers crossed that there are no leaks after install.
Picture not included in this copy
When I was putting together my air system for the air horns in both my old truck and yaris I used loctite brand thread sealant. 545 I believe it is. When you read the specs on this stuff you soon realize they probably use this stuff on the space shuttle. I highly recommend. Never had any issues with leaking air at 120psi.
Ah, thanks! I used teflon tape, but will probably remove my oil supply line and oil drain line and use the thread sealant. The water lines are banjo style and use both copper washers and metal/rubber combination seals, so no need for a thread sealant there, though it probably wouldn't hurt. Heading to town this afternoon to get a few clamps, so I'll pick up the thread sealant then. They don't have the loctite brand, only Permatex, but I expect it's basically the same stuff.Originally Posted by myfirstyota ↑When I was putting together my air system for the air horns in both my old truck and yaris I used loctite brand thread sealant. 545 I believe it is. When you read the specs on this stuff you soon realize they probably use this stuff on the space shuttle. I highly recommend. Never had any issues with leaking air at 120psi.
Trust me. It's not. Splurge and get a big bottle. You'll probably never need another. Warning. It is a bit pricey. The loctite brand is premium stuff. That's why home depot and Canadian tire don't Cary it.
We use their thread locker on our drilling rigs at work. Never lets us down.
Main reason I say this is because of the heat that the fitting will see. Permatex is great for every day application, but a turbo 2zr swapped yaris is not an every day car!
We use their thread locker on our drilling rigs at work. Never lets us down.
Main reason I say this is because of the heat that the fitting will see. Permatex is great for every day application, but a turbo 2zr swapped yaris is not an every day car!
I will take your advice and pick up the Loctite brand due to your ringing endorsement. 👍Originally Posted by myfirstyota ↑Trust me. It's not. Splurge and get a big bottle. You'll probably never need another. Warning. It is a bit pricey. The loctite brand is premium stuff. That's why home depot and Canadian tire don't Cary it.
We use their thread locker on our drilling rigs at work. Never lets us down.
Main reason I say this is because of the heat that the fitting will see. Permatex is great for every day application, but a turbo 2zr swapped yaris is not an every day car!
Oil drain fitting installation. A hole needs to be drilled in the block, but it's right inline with the front crossmember precluding the use of a standard drill. I picked up this little DeWalt 90 degree impact adapter for around $24.00. I just noticed this evening that Canadian Tire has a 3-piece 1/4" shank step drill bit kit on sale for $13.99, down from $39.99 (the same ones, likely, as the $9.00 kits available on eBay). Gee, thanks Canadian Tire. 😉
Here is where the hole needs to be drilled, and below that, my little DeWalk adapter.
Picture not included in this copy
Picture not included in this copy
Here is where the hole needs to be drilled, and below that, my little DeWalk adapter.
Picture not included in this copy
Picture not included in this copy
Upper Manifold Shield Off
Finally! This was a bear. The bolts that protruded through the captive nuts were very rusty and took a lot of soaking, wire brushing of the exposed threads below and considerable force to remove. I was sure I was going to break my 12mm ratchet wrench (A+ for Mastercraft Maximum). Each turn was a sharp snap. I worked them back and forth and finally they came out. Very tight space to work in too.
Picture not included in this copy
Manifold should come off tomorrow. After of course, I have to get the lower heat shield and manifold support bracket off. I have to remove the lower heat shield to get at the support bolts.
Picture not included in this copy
Here is the space I have to work with. I have about a 7" x 7" window. The turbo is close to 8" at the widest spot (the compressor outet), but I'm optimistic that I can tilt it over the steering rack and get it in there. The wastegate actuator and bracket will definitely have to come off and get reinstalled after the turbo is mounted. I'm less worried about the manifold, but it will have to go in first and by itself. I removed the long tunnel heat shield that runs back past the resonator. I'll replace this before I install the downpipe.
Picture not included in this copy
Finally! This was a bear. The bolts that protruded through the captive nuts were very rusty and took a lot of soaking, wire brushing of the exposed threads below and considerable force to remove. I was sure I was going to break my 12mm ratchet wrench (A+ for Mastercraft Maximum). Each turn was a sharp snap. I worked them back and forth and finally they came out. Very tight space to work in too.
Picture not included in this copy
Manifold should come off tomorrow. After of course, I have to get the lower heat shield and manifold support bracket off. I have to remove the lower heat shield to get at the support bolts.
Picture not included in this copy
Here is the space I have to work with. I have about a 7" x 7" window. The turbo is close to 8" at the widest spot (the compressor outet), but I'm optimistic that I can tilt it over the steering rack and get it in there. The wastegate actuator and bracket will definitely have to come off and get reinstalled after the turbo is mounted. I'm less worried about the manifold, but it will have to go in first and by itself. I removed the long tunnel heat shield that runs back past the resonator. I'll replace this before I install the downpipe.
Picture not included in this copy
Your stock manifold looks a lot different than mine. I noticed mine looks like a typical aftermarket welded and bent tube design whereas yours appeals to looks like a cast design. I would have assumed they would he the exact same.
Btw great job so far and I appreciate you taking pics of everything
Btw great job so far and I appreciate you taking pics of everything
Thanks, Trevor. Pretty sure mine is welded tubing, though it does look cast in the pics.Originally Posted by tmontague ↑Your stock manifold looks a lot different than mine. I noticed mine looks like a typical aftermarket welded and bent tube design whereas yours appeals to looks like a cast design. I would have assumed they would he the exact same.
Btw great job so far and I appreciate you taking pics of everything
I was hefting the turbo tonight and it's quite a heavy beast. The manifold, as you know has 2 studs/nuts up top and 3 below. I don't quite understand this as the reverse would be more structurally sound, IMO. I'm going to see how difficult it might be to adapt the existing manifold support bracket to work with the turbo. There are 6 bolts on the compressor housing and 4 on the turbine. If it works in a way that the turbo downpipe clears the stock support bracket, I may see if I can bolt a support arm from the stock bracket to the turbo using either the compressor or turbine bolts - which ever is more centered over the support. I know the turbokits guys knew what they were doing when they built the kit, but it just seems like a lot of mass hanging from that manifold. The manifold itself could probably hold a ton (not exaggerating) but I'm a concerned about the 5 fairly small studs/nuts that hold it on. If the Toyota engineers thought that the small lightweight manifold needed a support, then I'm thinking that this turbo is a heck of a lot heavier and could use some support. Maybe I'm overthinking this. 🤷
I wouldn't say so..brace that puppy as best you can.Originally Posted by 06YarisRS ↑..... I know the turbokits guys knew what they were doing when they built the kit, but it just seems like a lot of mass hanging from that manifold. The manifold itself could probably hold a ton (not exaggerating) but I'm a concerned about the 5 fairly small studs/nuts that hold it on. If the Toyota engineers thought that the small lightweight manifold needed a support, then I'm thinking that this turbo is a heck of a lot heavier and could use some support. Maybe I'm overthinking this. 🤷
The manifold is off with no broken studs. I think the wire brushing and days of soaking with the ReleasAll really helped. They were tight, but turned smoothly.
I was thrilled that the tunnel is big enough to pull the manifold through, so I'm optimistic that the turbo and turbo manifold will fit through, though separately.
The most involved part was removing all the heat shields. You have to take off one at a time to reveal the next set of bolts. Because of their proximity - obviously - to the heat of the manifold, the exposed threads past the captive nuts get really rusty and explode, making them very difficult to remove. Anyway, on to the pics...
Nasty Heat Shields/bracket Removed (these bolts themselves were in good shape, unlike many of the others):
Picture not included in this copy
Manifold Nut Removal:
Picture not included in this copy
Manifold Out:
Picture not included in this copy
Manifold Gasket (Ordering a new one tomorrow)
Picture not included in this copy
Ready for Turbo Manifold ( I may see what's involved in procuring and replacing the firewall padding as mine's a bit ratty. Or, I'll just trim if off neatly):
Picture not included in this copy
I was thrilled that the tunnel is big enough to pull the manifold through, so I'm optimistic that the turbo and turbo manifold will fit through, though separately.
The most involved part was removing all the heat shields. You have to take off one at a time to reveal the next set of bolts. Because of their proximity - obviously - to the heat of the manifold, the exposed threads past the captive nuts get really rusty and explode, making them very difficult to remove. Anyway, on to the pics...
Nasty Heat Shields/bracket Removed (these bolts themselves were in good shape, unlike many of the others):
Picture not included in this copy
Manifold Nut Removal:
Picture not included in this copy
Manifold Out:
Picture not included in this copy
Manifold Gasket (Ordering a new one tomorrow)
Picture not included in this copy
Ready for Turbo Manifold ( I may see what's involved in procuring and replacing the firewall padding as mine's a bit ratty. Or, I'll just trim if off neatly):
Picture not included in this copy
The Good: The manifold and turbo fit separately through the tunnel.
Picture not included in this copy
Picture not included in this copy
The Bad: In its current state, there is not enough room for the turbo between the head and firewall.
The OK: However, I think I really only need to make about a 1" deep indentation in the firewall for adequate clearance - maybe a touch more to allow for engine rocking. I wonder what's directly behind this area in the car. So, I'll be bringing home, from the shop tomorrow a couple of brass rods and a big-arse hammer. I'll have to peel the carpet bak and make sure I won;t damage anything in that area.
Edit: On another very positive note, I took the downpipe out and it looks as though it is going to fit perfectly without any mods. Very happy about that!
I also have to clock the turbo a few more degrees so the compressor outlet lines up allowing the charge pipe to fit in the opening between the subframe and axle.
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
The Bad: In its current state, there is not enough room for the turbo between the head and firewall.
The OK: However, I think I really only need to make about a 1" deep indentation in the firewall for adequate clearance - maybe a touch more to allow for engine rocking. I wonder what's directly behind this area in the car. So, I'll be bringing home, from the shop tomorrow a couple of brass rods and a big-arse hammer. I'll have to peel the carpet bak and make sure I won;t damage anything in that area.
Edit: On another very positive note, I took the downpipe out and it looks as though it is going to fit perfectly without any mods. Very happy about that!
I also have to clock the turbo a few more degrees so the compressor outlet lines up allowing the charge pipe to fit in the opening between the subframe and axle.
Picture not included in this copy
Picture not included in this copy
And the modification begins! Hahaha
This is the fun part!!
This is the fun part!!
Another thing you may want to consider is a poly filled dogbone trans mount. Keep the clearances in check by minimizing engine rock.
^what he said.
It will limit the amount the engine moves so it needs less clearance at the fire wall. With only one mount in the sagittal plane there is little to hold the engine in place
It will limit the amount the engine moves so it needs less clearance at the fire wall. With only one mount in the sagittal plane there is little to hold the engine in place
I've read about those poly mounts. This is something I would have to make on my own, is it not? I think you made some Trevor, didn't you? I doubt there is one available to purchase for my application. I'm definitely interested. Last thing I want is the turbo smashing into the firewall under acceleration - or anytime, obviously. Suggestions/additional info welcomed.
Just read about filling the mount with 3M window sealant. This doesn't sound like a long-term solution, though I did read a few success stories. I figured it would fall out but it connects and bonds together from both sides, so maybe it would last.
Also watched this video:
https://www.youtube.com/watch?v=aYzL-IXqiSY
Just read about filling the mount with 3M window sealant. This doesn't sound like a long-term solution, though I did read a few success stories. I figured it would fall out but it connects and bonds together from both sides, so maybe it would last.
Also watched this video:
https://www.youtube.com/watch?v=aYzL-IXqiSY
Correct, I made my own out of 94a poly (stiffest they had). I bought a pre measured kit from energy suspension and as long as you properly mix them it works great and is very durable.
The first time I did this I didn't dremel any of the stock rubber mount away and I improperly mixed the liquids so it was slightly brittle. It still.worked but cracked so it loosened up the mount a bit.
The second time I made sure to do it right. I deremel'd out as much of the factory rubber as i could while leaving enough in there to keep the middle metal sleeve in the correct place.
I mixed all the liquid at once (that is recommended) and let it sit 5 days before install. I can't easily check my doggone mount but the last time I was down there is looks great and I have never had that knocking sound come back since I installed them. The sound was due to tje trans hitting the subframe.
I recently inspected my trans mount since I can easily see it with no battery in the way and it had not cracked at all and still looks great.
There is nothing available in the aftermarket so we are kind of left to make one ourselves. I wrote up brief diy on it with pictures, if the pictures are not still in the thread just let me know
The first time I did this I didn't dremel any of the stock rubber mount away and I improperly mixed the liquids so it was slightly brittle. It still.worked but cracked so it loosened up the mount a bit.
The second time I made sure to do it right. I deremel'd out as much of the factory rubber as i could while leaving enough in there to keep the middle metal sleeve in the correct place.
I mixed all the liquid at once (that is recommended) and let it sit 5 days before install. I can't easily check my doggone mount but the last time I was down there is looks great and I have never had that knocking sound come back since I installed them. The sound was due to tje trans hitting the subframe.
I recently inspected my trans mount since I can easily see it with no battery in the way and it had not cracked at all and still looks great.
There is nothing available in the aftermarket so we are kind of left to make one ourselves. I wrote up brief diy on it with pictures, if the pictures are not still in the thread just let me know
Благодарю вас. Это не будет работать, потому что выхлопная труба не будет в выравнивании. (Thank you. This will not work because the exhaust pipe will not be in alignment)Originally Posted by Tima122 ↑Повените турбину на 180 градусов по горизонтали
People see to use the term "messaging" the firewall. I call it beating the crap out of it. I'm not finshed, but I've basically created about a 1.5" - 2" cup into which the turbo compressor housing can fit when the engine rocks backwards under acceleration. I used the blunt end of my breaker bar and a big hammer. I worked in a ever decreasing diameter. Right now the turbo should clear as I believe it should rotate downwards slightly. I base this on the positioning of the motor mounts. I plan to grind down the rough bits, skim it with bondo, quick sand, prime and color match paint it. I have about a pint of the OEM color left, so I'm good for supplies.
I also picked up a tube of Proform Urethane and will remove the dogbone mount and fill that up. If it does fail, I'll redo it as per Trevor's approach with actual catalyzed urethane.
I also permanently mounted the manifold. The OEM gasket was in good shape, but received a thin bead of Copper High Heat RTV on both sides, so hopefully no leaks. The RTV squeezed out ever so slightly, so the seal should be good. I'll retorque again tomorrow.
Picture not included in this copy
I also picked up a tube of Proform Urethane and will remove the dogbone mount and fill that up. If it does fail, I'll redo it as per Trevor's approach with actual catalyzed urethane.
I also permanently mounted the manifold. The OEM gasket was in good shape, but received a thin bead of Copper High Heat RTV on both sides, so hopefully no leaks. The RTV squeezed out ever so slightly, so the seal should be good. I'll retorque again tomorrow.
Picture not included in this copy
Awesome job, just a slight massage!
Here are some measurements, WeeYari. The dimensions listed on the site are based on the core size. The overall length is about 27" including the end caps.Originally Posted by WeeYari ↑It certainly is!
It looks bigger than specs on the site. Must be skinny plank flooring that it is resting on.
Sent from my EML-L09 using Tapatalk
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Haha. Thanks manOriginally Posted by tmontague ↑Awesome job, just a slight massage!
HVAC?
I'm hoping that I didn't damage my HVAC when "messaging" my firewall. I don't know of anyone that has had their HVAC (condensor/heater core, controller unit) out. Before I started pounding on the firewall, I slid my fingers up behind the unit and it appeared there was enough room - at the bottom. I can still get my fingers between the firewall and blower unit at the bottom. But, the unit takes a turn back to the firewall and I'm not sure how close it gets. Judging by the rubber drain hose, the unit itself seems higher up.
Wish me luck...I'm going start the car (a real racket it will be with just the log manifold) and I'll test my HVAC and see if everything is operational. Serious fingers crossed as this is a job that I REALLY don't want to get into! 😲
I did find this post in which CT Scott shows pics of the unit. I tired working my miraculous spatial geometry skills, but it got me no further toward determining how close the unit rests to the firewall. It does look like it is supported on a crossbar under the dash, and there was no evidence of fasteners on the outside area of the firewall that I abused.
Unique Smell from Air Going Through AC Blower
Picture not included in this copy
I'm hoping that I didn't damage my HVAC when "messaging" my firewall. I don't know of anyone that has had their HVAC (condensor/heater core, controller unit) out. Before I started pounding on the firewall, I slid my fingers up behind the unit and it appeared there was enough room - at the bottom. I can still get my fingers between the firewall and blower unit at the bottom. But, the unit takes a turn back to the firewall and I'm not sure how close it gets. Judging by the rubber drain hose, the unit itself seems higher up.
Wish me luck...I'm going start the car (a real racket it will be with just the log manifold) and I'll test my HVAC and see if everything is operational. Serious fingers crossed as this is a job that I REALLY don't want to get into! 😲
I did find this post in which CT Scott shows pics of the unit. I tired working my miraculous spatial geometry skills, but it got me no further toward determining how close the unit rests to the firewall. It does look like it is supported on a crossbar under the dash, and there was no evidence of fasteners on the outside area of the firewall that I abused.
Unique Smell from Air Going Through AC Blower
Picture not included in this copy