Replies continued
ArmstrongRacingSan Diego · Oct 27, 2018#201Awesome!
The hardest part is over now, it should be smooth sailing to the finish line
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 27, 2018#202 Originally Posted by
ArmstrongRacing ↑ Awesome!
The hardest part is over now, it should be smooth sailing to the finish line
Thanks Tom! Probably the hardest 'physical' part is over. Now, haha, all those hoses and wires! Mental anguish, LOL!
I have to remove the passenger side mount as I had removed the AC line. it really looked like it was going to get damaged. Of course, I forgot to re-install that before bolting the mount down. I
think it should be fairly easy. Support the engine underneath with a jack, remove the mount, re-install the a/C line and then put the mount back.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 27, 2018#203 Originally Posted by
ArmstrongRacing ↑ The alignment is a bit tricky for sure. But you definitely shouldn’t remove the alignment pins. I remember having to fight with it for a while and I had a second hand to help.
Take a step back and see where the flanges are not exactly flush, try to correct that and line up the bolt holes
Hey Tom. I've been thinking about the pins and I bet they offer some support to the structure too. They are very tight in their holes. With all the bolts (9), I believe, should I be ok? I mean, it should be strong enough, shouldn't it?
As you alluded to before, the pegs were actually in the same positions on both the engine and trans. So, the pair on the engine was removed. We actually couldn't get the pegs out of the trans, even with heat, so (and I hope not to get flamed for this though I probably deserve it), I cut them off flush with a hacksaw. 😳 I'm not proud of this somewhat botched job, it's just I was under a little pressure with the engine hanging there and wanted it in quick.
atomic_hojiKincardine, ON, Canada · Oct 27, 2018#204Great progress man! 👍
Sorry you've had a struggle with the transmission - was worth a try to do it in place, lesson learned I guess? 😁
Just a quick note - be careful using tie-down straps as rigging, if those clamps let go you could lose the load; no fun when it's an engine, even if it's a little one. I try to use chains and rated shackles for rigging. Please dear god never use rope! Regardless how you do it, let it hang for a couple minutes and give it a shake to test it - stay safe!
Keep us posted how you make out tonight / tomorrow!
-- Adam
tmontagueCaledonia Ont. · Oct 27, 2018#205Reconnecting the a/c lines shouldn't be too bad with the steps you mentioned.
I also dont think the lack of alignment pins will be that big of a deal. The trans and engine fine have much shear force as the engine mount placement leads to the top part compressing and the bottom experiencing tensile force.
I've been in your shoes before and sometime you have to do what you have to do
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 27, 2018#206 Originally Posted by
atomic_hoji ↑ Great progress man! 👍
Sorry you've had a struggle with the transmission - was worth a try to do it in place, lesson learned I guess? 😁
Just a quick note - be careful using tie-down straps as rigging, if those clamps let go you could lose the load; no fun when it's an engine, even if it's a little one. I try to use chains and rated shackles for rigging. Please dear god never use rope! Regardless how you do it, let it hang for a couple minutes and give it a shake to test it - stay safe!
Keep us posted how you make out tonight / tomorrow!
-- Adam
Thanks Adam! Lesson learned for sure! Yes, I confess I didn't do a great job preparing the lifting apparatus. I had lofty plans to buy chains, lifting hooks and an engine leveler, but I just slacked off at the end. I have to say, I was pretty impressed with my $14.00 Crappy Tire tie down straps, but, indeed, they are not the correct gear to use. I had lifted the engine with two straps and it seemed to hold, so I felt confident with 4. But, even with four, I know I could have played a tune on them...they were tight!
I did a bit more tonight - fixed the A/C line issue which was deadly trying to get the motor mount bracket bolt in my myself. It was a bit of a contortionist act with prying, jacking, leaning into it all while trying to start the threads in the bolt. I put the torque converter bolts in and in the process lost the little plastic cover. Will scour the garage tomorrow and find that. Also mounted the starter. Finally, I looked at the Yaris harness for the speed sensor wires. I'm seriously considering calling Toyota on Monday and sourcing some pins for the fuse box connector (CA2?). Rather than butcher my Yaris harness, I may just make a new leg for the Scion harness. For now I'd just take the plug from the Yaris speed sensor and use it - or try to order one. That way if I ever want to use the old Yaris harness again - or sell it - I would just need to put a connector on it.
Anyway, thanks again for all your help and I'll update tomorrow on what I get done. Hoping to have most of the wiring done and hopefully some hoses. I have no idea how I'm going to make the heater hoses work with this engine as one of the connections is on the back of the engine as opposed to both on the side in the Yaris.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 27, 2018#207 Originally Posted by
tmontague ↑ Reconnecting the a/c lines shouldn't be too bad with the steps you mentioned.
I also dont think the lack of alignment pins will be that big of a deal. The trans and engine fine have much shear force as the engine mount placement leads to the top part compressing and the bottom experiencing tensile force.
I've been in your shoes before and sometime you have to do what you have to do
I did get the A/C line back on Trevor, but it was tough doing it by myself.
Glad the pins won't make a difference.
Well, I consider having to remove the pins a compromise and I would definitely have preferred not to. It detracts - if even in a small way - from my overall feeling of a job really well done. That said, if that's the only hitch I run into, I'll be pretty darn happy.
I'll approach the wiring/hoses and tubing with trepidation.
Thanks for the help. More updates to come tomorrow.
ArmstrongRacingSan Diego · Oct 28, 2018#208 Originally Posted by
tmontague ↑ I also dont think the lack of alignment pins will be that big of a deal. The trans and engine fine have much shear force as the engine mount placement leads to the top part compressing and the bottom experiencing tensile force.
It's not about strength, the pins facilitate proper alignment of the crankshaft and transmission input.
With an automatic its not really a big deal, since the torque converter and flexplate have a tight interference fit. With a manual transmission its a more serious affair, since the Toyota input shafts are floating.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 28, 2018#209 Originally Posted by
ArmstrongRacing ↑ It's not about strength, the pins facilitate proper alignment of the crankshaft and transmission input.
With an automatic its not really a big deal, since the torque converter and flexplate have a tight interference fit. With a manual transmission its a more serious affair, since the Toyota input shafts are floating.
Thanks Tom. Now that you mention it, that little nub of the shaft that protrudes throught the torque converter goes into that little cup on the crankshaft and by looking at them, there doesn't seem like there would be much clearance. I'm pretty sure there won't be any rubbing there as the last couple of bellhousing bolts threaded in almost fully by hand tightening.
atomic_hojiKincardine, ON, Canada · Oct 28, 2018#210If you need wiring terminals you'll find that Toyota sells them as "pigtails" - pre-crimped terminal on a length of ~6" of wire. More than likely they will have to special order them, unless it's a large dealership and they happen to have someone who does a bunch of wiring; I only have pretty small dealerships "local" to me, so nearly everything is ordered.
If you can take the connector in to show them there's a better chance they'll get the correct terminals for you too; they'll of course ask the make/model/year as well.
Keep at it! 👍
-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 28, 2018#211 Originally Posted by
atomic_hoji ↑ If you need wiring terminals you'll find that Toyota sells them as "pigtails" - pre-crimped terminal on a length of ~6" of wire. More than likely they will have to special order them, unless it's a large dealership and they happen to have someone who does a bunch of wiring; I only have pretty small dealerships "local" to me, so nearly everything is ordered.
If you can take the connector in to show them there's a better chance they'll get the correct terminals for you too; they'll of course ask the make/model/year as well.
Keep at it! 👍
-- Adam
Thanks Adam! Now that I'm back in the garage and rolling, I'm reconsidering waiting for additional parts. So, I may go ahead and scavenge the parts from the Yaris harness. One thing I'm struggling with is getting some of the harness retaining clips lined up with the mounts on the engine. I think the plastic clips can be moved, but I'm worrying that I may not have the harness installed perfectly. So far, all connectors are reaching their plugs. Here is a pic to illustrate what I mean. I don't like yanking and twisting the harness for obvious reasons. Many of the clips do align with the mounts but several don't. I think I can move the connectors along the harness but it leads me to believe I've not properly installed it. Is it acceptable to use heavy wire ties for those areas that I cannot attach a proper retaining clip? I wonder if this is just the difference between the Corolla engine I have and the xD harness. Anyway, here is the pic...
Picture not included in this copy On a positive note, I've got the ground for the transmission done, I hope correctly. It's also in the pic above. I heat shrinked and retaped that whole junction of the harness. Now... on to the speed sensor wiring!
REMINDER TO SELF...put oil, ATF and coolant in before starting the car!!! atomic_hojiKincardine, ON, Canada · Oct 28, 2018#212Might just be a difference between Corolla harness and xD harness? A bit of a lug to pull slack or maybe route differently around something will give you some slack? If not, a zip tie to pull the cable snug with the bracket should do the trick just fine. Because of the differences (i.e. ECM mounts on the complete opposite side of the car) between the iM and the Yaris I have a number of plastic cable connectors that I've had to do that with.. As long as all of the electrical connectors go to their partner engine sensor, I'd say you're all good. 😁
And yes, I hear engines and transmissions get cranky without oil.. If nothing else, put a stick-note on the steering wheel! lol
-- Adam
tmontagueCaledonia Ont. · Oct 28, 2018#213Dont worry about all of the harness mounts. They won't all line up as you experienced. Enough will line up so the harness is still supported.
What I always do when my engine is empty if any fluids is to keep the oil cap unscrewed but covering the fill hole fto keep debris out. This reminds me that there is something missing in the engine
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 28, 2018#214Help!!!
No matter what I try, I cannot get the pins out of the speed sensor connector. I tried using a sewing pin, safety pin with light pushing, picking etc. I can't get these wires out and I'm afraid I'm going to ruin them in the process. I'm basing this on brushforhire's thread in which he says it tricky. I'll say, haha. Is there some kind of release mechanism I'm missing?
Any advice would be really, really appreciated!
Picture not included in this copy
atomic_hojiKincardine, ON, Canada · Oct 28, 2018#215Looking at the picture it's hard to tell, but do you have the safety latch on the connector popped up? If not, the terminal will be latched into the connector body and be (virtually - you can yank and shred the plastic) impossible to remove. A tiny screwdriver can pop the latch up, then just keep it up and loose while you work your magic on the specific wire/terminal you want to pop out..
As for popping the terminals, try to visualize the terminal as square tube (female terminal usually, so I assume here..) and inside where the tube sits inside the connector there is a small, plastic wedge that is retaining the terminal. What you want to do is slide the sewing / safety pin along the top of the terminal to push it between the terminal and the plastic wedge. Then gently lever the plastic wedge up and away from the terminal; it sometimes helps to push inward on the connector while you feel this out. Then gently pull rearward on the wire backside of the connector and wiggle it out.
Dunno if that makes sense to visualize..? Once you have the hang of it, it becomes easier to know what to fell for... the first few times I tried I went at it for like half an hour and felt daft as a post; and my back hurt from hunching over.. lol.
-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 28, 2018#216 Originally Posted by
atomic_hoji ↑ Looking at the picture it's hard to tell, but do you have the safety latch on the connector popped up? If not, the terminal will be latched into the connector body and be (virtually - you can yank and shred the plastic) impossible to remove. A tiny screwdriver can pop the latch up, then just keep it up and loose while you work your magic on the specific wire/terminal you want to pop out..
As for popping the terminals, try to visualize the terminal as square tube (female terminal usually, so I assume here..) and inside where the tube sits inside the connector there is a small, plastic wedge that is retaining the terminal. What you want to do is slide the sewing / safety pin along the top of the terminal to push it between the terminal and the plastic wedge. Then gently lever the plastic wedge up and away from the terminal; it sometimes helps to push inward on the connector while you feel this out. Then gently pull rearward on the wire backside of the connector and wiggle it out.
Dunno if that makes sense to visualize..? Once you have the hang of it, it becomes easier to know what to fell for... the first few times I tried I went at it for like half an hour and felt daft as a post; and my back hurt from hunching over.. lol.
-- Adam
Thanks very much, Adam! I got the terminals out, basically at the expense of the connector. I've also decided rather than tear the harness apart, I'm creating my own leg (for lack of a better term). I'll ziptie that to the main harness.
Even after I had the retaining clip lifted on the connector, the wires did not want to come out. Basically I hacked away at the connector with my utility knife until enough material was removed and the pins came out intact. This is a hamfisted way to do it and I'm not proud, but I am confident enough to install a new connector (assuming one is available) should I ever decide to repair the Yaris harness.
Please avert your eyes from the connector carnage.
Picture not included in this copy Parts for new speed sensor harness. I will solder each and heat shrink each connection, run it through conduit, then tape the whole thing. Then run it along side the engine harness.
Picture not included in this copy tmontagueCaledonia Ont. · Oct 28, 2018#217You need to pop up the retaining clip which you did and then you need to take a small needle (I used a sewing needle) and push down on the pin you want out.
I cannot remember which way or really explain it well but I practised for weeks on mine before I actually did the swap.
Once you get it you'll understand. But bottom line is you need to use a small pin to actually push the prong down that also holds the pin in. So there are 2 things that hold the pin in, not just the main retaining clip on the connector
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 28, 2018#218 Originally Posted by
tmontague ↑ You need to pop up the retaining clip which you did and then you need to take a small needle (I used a sewing needle) and push down on the pin you want out.
I cannot remember which way or really explain it well but I practised for weeks on mine before I actually did the swap.
Once you get it you'll understand. But bottom line is you need to use a small pin to actually push the prong down that also holds the pin in. So there are 2 things that hold the pin in, not just the main retaining clip on the connector
Thanks Trevor! I didn't have much luck with the pin. I'm guessing, as you say, practice is the key. After all my toils getting them out, I actually took one out that wasn't the right one, lol. I ended up with a pink, white/black stripe and a brown. The brown was wrong, so I went back and got the black one.
Would I be correct in assuming that inserting the pins only requires that the retaining clip is in the up position? Also, I'm pretty sure that the flat part of the pin goes in facing down. I'd sure hate to get these in and have to try to remove them again, lol.
Here is the harness I made. I gave myself a little extra length so I could route where I want when I install it. I think this sucker would operate under water with no shorts. It's seriously soldered, heat shrinked, taped, split loom and taped again!
Picture not included in this copy 06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 28, 2018#219Guess I need a Edit: non-micro" add-a-circuit. Learning more and more by the day...🙄 haha.
Picture not included in this copy
Not all bad news. I'm about to connect the speed sensor wires to the fuse box connector. Just have to confirm correct wire placement.
Picture not included in this copy
Here is the ground wire added to the transmission plug. The blue wire going to pin location 10 is cut and an eyelet is added and it is bolted to the block.
Picture not included in this copy
tmontagueCaledonia Ont. · Oct 28, 2018#220Technically a non micro fuse tap works (that's what I used in my under dash wiring) however if you use it in the fuse box under the hood it will not allow you to close the lid all the way. It will still work temporarily however and it will give you an idea if you wired everything properly
And yes the pins can be inserted with only the main retaining clip opened, its removing them where you have to deal with the secondary retaining system
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 28, 2018#221 Originally Posted by
tmontague ↑ Technically a non micro fuse tap works (that's what I used in my under dash wiring) however if you use it in the fuse box under the hood it will not allow you to close the lid all the way. It will still work temporarily however and it will give you an idea if you wired everything properly
And yes the pins can be inserted with only the main retaining clip opened, its removing them where you have to deal with the secondary retaining system
Thanks Trevor! Great idea. I will check my wiring with what I have. In the meantime, I will search for a micro add-a-circuit.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 28, 2018#222Heater Hoses Installed
These hoses both needed a few inches cut off of them. I do not know which one is the inlet and which one is the outlet. The rearmost hose would attach without kinking but it was touching the firewall and with the engine moving back and forth, I thought it prudent to shorten it so that it doesn't rub.
Picture not included in this copy
ArmstrongRacingSan Diego · Oct 28, 2018#223Looking good! I also used a non-micro add-a-circuit. It helps to clear the other fuses in the engine fuse box. Trevor is correct about the interior fuse box though, you won't be able to reuse the cover once you install one there....but the only reason to install these inside is for gauges or displays.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 28, 2018#224Little Red Cap Game...Anyone want to play? 😁
Picture not included in this copy
Here are my guesses:
1) fuel line?
2) no idea what this is where this one goes to. It is built into a unit with an electrical connector if that helps.
3) brake booster? (this tubing traces back to the intake manifold)
4) goes to intake tube attached to airbox?
I do seem to have a couple of hoses left over from the Yaris but they don't seem fit on this engine. 🤷
Also, I got my radiator and upper brace back on. There is no way the Yaris radiator hose clamps will go on the Corolla water pump outlet. I had the clamp tabs touching and it would not go over the tube lip. I had it lubed with silicone, wiggles, twisted...no go! I think I'll actually pick up a new lower rad hose and clamp from the dealership.
Lastly, and Trevor maybe you can help me out with this. I did attach my A/C line to the compressor and there's a bit of strain on the rubber part of the hose. I recall you saying that you bent the tubing. Can you elaborate on that a bit for me please? Did you bend the longer, upper part of the aluminum tubing down, or the lower curled part near the compressor upwards? Or neither. 😆
tmontagueCaledonia Ont. · Oct 29, 2018#225I'll have to look at my engine to see where those red capped tube openings go. Iirc number 4 goes directly to a port on the intake tube before the throttle body.
In regards to the a/c, I bent the lower part near the compressor. I dont remember which was but enough where the rubber part was no longer rubbing against anything and there was less strain on it. I put it in a vice to bend
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 29, 2018#226 Originally Posted by
tmontague ↑ I'll have to look at my engine to see where those red capped tube openings go. Iirc number 4 goes directly to a port on the intake tube before the throttle body.
In regards to the a/c, I bent the lower part near the compressor. I dont remember which was but enough where the rubber part was no longer rubbing against anything and there was less strain on it. I put it in a vice to bend
Thanks Trevor! That would be awesome!
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 29, 2018#227Could you guys have a look at post #219? I just want to verify that the wiring looks ok, especially the last pic - that I just added - of the blue ground wire which comes from pin 10.
Thanks!
tmontagueCaledonia Ont. · Oct 29, 2018#228From what u remember that appears to be the correct spots. However, I'd need to go through the threads to confirm
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 29, 2018#229 Originally Posted by
tmontague ↑ From what u remember that appears to be the correct spots. However, I'd need to go through the threads to confirm
Yeah, I think it's right. I think I did what Tom said to do as per brushforhire's thread. Just wanted to be sure. Thanks Trevor.
atomic_hojiKincardine, ON, Canada · Oct 29, 2018#2301. looks like fuel - trace it toward the engine, should run along the side of the cyl. head and up to the fuel rail.
2. purge solenoid - should have an electrical connector just above (power to sol'd) and a tube will run to the firewall to the NON-fuel supply line from the fuel tank; can follow the pair of hard lines under the car rearward. This vents the fuel canister I believe.
3. no idea? I don't have a rear line like that, unless the Corolla(sedan) has heater lines different than the I'm. Maybe run back to the block and see where it comes from?
4. valve cover vent - as Trevor noted does to a nipple on the intake tube a few inches before your throttle body.
Sorry, on phone, so short and probably type-o filled.. lol
-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 29, 2018#231 Originally Posted by
atomic_hoji ↑ 1. looks like fuel - trace it toward the engine, should run along the side of the cyl. head and up to the fuel rail.
2. purge solenoid - should have an electrical connector just above (power to sol'd) and a tube will run to the firewall to the NON-fuel supply line from the fuel tank; can follow the pair of hard lines under the car rearward. This vents the fuel canister I believe.
3. no idea? I don't have a rear line like that, unless the Corolla(sedan) has heater lines different than the I'm. Maybe run back to the block and see where it comes from?
4. valve cover vent - as Trevor noted does to a nipple on the intake tube a few inches before your throttle body.
Sorry, on phone, so short and probably type-o filled.. lol
-- Adam
"Type-o-filled" - like most of my posts. 😆
Thanks for the explanations! I should have recongized #2 as I changed out the purge solenoid and NVLD pump on my Grand Caravan...duh! Haha.
#3 goes to the connector on the intake manifold; the one that I couldn't find the hose for, but was sitting right next to it. LOL! I
think this is where the brake booster gets its vacuum from. Again, I
think it connects to that long hose that is held up under the wiper tray and goes to the brake booster.
Getting excited for 'start-up day'!
Then, it's exhaust work and then finally A/C.
ArmstrongRacingSan Diego · Oct 29, 2018#232 Originally Posted by
06YarisRS ↑
Picture not included in this copy
#1 - You will need to remove the metal connector on the fuel line in the center of this picture. You will need a special fuel line tool to get it off, like this :(skip to 5:00 mark)
https://youtu.be/JFUmQF82GW0 #2 - yes, purge hose that goes to evap metal pipe on firewall (regular hose barb, not fuel line barb)
#3 - yes, brake booster
#4 - yes, to intake boot
post #219 looks good as well
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 29, 2018#233 Originally Posted by
ArmstrongRacing ↑ #1 - You will need to remove the metal connector on the fuel line in the center of this picture. You will need a special fuel line tool to get it off, like this :(skip to 5:00 mark)
https://youtu.be/JFUmQF82GW0 #2 - yes, purge hose that goes to evap metal pipe on firewall (regular hose barb, not fuel line barb)
#3 - yes, brake booster
#4 - yes, to intake boot
post #219 looks good as well
Thanks very much Tom! Re: fuel line connector. After reading your post, I thought, "Hey, I'll just get my dremel tool out and carefully grind away until I can carefully remove the connector without damaging the fuel line". Then I thought, "Well, maybe not such a great idea as it is a
FUEL line"! That could make a quick end to this project! I will find the tool.
Just got the lower rad hose on. The clamp was a bear as the tabs had bent over. Got them bent back in the vice and the clamp is now on nice and tight. Tonight the airbox goes in and all tubing attached. Time permitting, oil, ATF and coolant will be 'added'.
I feel a start attempt is imminent. I'm tempted to start it without the exhaust attached but that is probably not advisable. Regardless, before the first start, I'll be querying you guys. Thanks very much again.
tmontagueCaledonia Ont. · Oct 29, 2018#234Hell, give it a go, I ran mine with open headers :D
Great job so far
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 29, 2018#235 Originally Posted by
tmontague ↑ Hell, give it a go, I ran mine with open headers :D
Great job so far
Haha, I just might fire it up without exhaust. What a racket she'll make LOL.
Didn't get as much done as I had wanted to tonight. I really wanted to get the airbox on. I think I'll leave the battery out until the fuel line is dealt with. I did get the transmission cooler lines reconnected, replaced - with new WS - the drained atf, which I didn't really need to drain, but it was close to my scheduled change out anyway. I bent my A/C line at the bottom, where you did Trevor to take pressure off the hose, hooked up all the A/C lines, hooked up the evap lines and brake booster line. I also reinstalled the front crossmember. What slowed me down a bit was that I realized after most of the front was put back together that I had left the hood latch on the outside. After examining it, I realized (of course, silly me) that all I had to do was disconnect the cable and pass it back through.
The young fella is coming back tomorrow to help install the exhaust, so I maybe won't get to start it without exhaust after all. This fuel line is now what will hold me up. Oh, and I did source a low profile mini add-a-circuit today at the local parts store and for only $11.00 (school discount LOL). But, of course I forgot to get another low profile fuse. Of course, there were no spares in the under hood fuse box. Maybe there are in the inside fuse box. And I have double the chance, as I have two Yari!
Anyway, here is the current state of the car. This pic was taken before I moved the latch back inside and mounted it. Oh, and that fat short hose on top of the engine is just a remnant from the Yaris hoses.
Picture not included in this copy tmontagueCaledonia Ont. · Oct 30, 2018#236You shouldn't need a mini fuse for the mini fuse tap. A regular fuse will work it will just extend out a little further that is all. Since it travels horizontally it won't interfere with th cover.
Triple check those a/c lines and make sure they are secure!
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 30, 2018#237 Originally Posted by
tmontague ↑ You shouldn't need a mini fuse for the mini fuse tap. A regular fuse will work it will just extend out a little further that is all. Since it travels horizontally it won't interfere with th cover.
Triple check those a/c lines and make sure they are secure!
Hey Trevor. I actually picked up a low profile fuse on the way to work today. I was referencing your pic for placement in the fuse box and it didn't look like the non-low profile ones would fit due to an adjacent obstruction in the fuse box.
MAF Voltage question... When I was picking my fuse up, I was explaining to the counter guy what I was using this to power a MAF sensor. He advised that I not supply the MAF sensor with straight 12 volts and said it should receive about 5V. I know you guys have been wiring direct. Are there any issues with providing 12V directly to the MAF?
Thanks!
tmontagueCaledonia Ont. · Oct 30, 2018#238Zero issue what so ever. Iirc tom original thread stated that the maf needs to receive 12v power source not 5v
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 30, 2018#239 Originally Posted by
tmontague ↑ Zero issue what so ever. Iirc tom original thread stated that the maf needs to receive 12v power source not 5v
Great. Thanks. I was inquiring more out of interest as I would, without hesitation, take your guys' word over anyone elses'. You guys have proven that this all works.
ArmstrongRacingSan Diego · Oct 30, 2018#24006YarisRSThread starterFredericton, New Brunswick, Canada · Oct 30, 2018#241The Good: It started after about 5 seconds of cranking. The engine runs very smooth and sounds good.
The Bad: 1) I have a battery light and 10.2 volts. EDIT: I now have less than 9 volts and the car won't turn over. I guess I'll take the alternator off and have it tested.
Could some of the other problems be caused by low voltage?
2) I'll let the picture do the talking.
Picture not included in this copy
I don't know whether to laugh or cry!
Hoping to get your advice/opinions, gents!
I'm pretty sure all the conectors are attached.
For the P0102, I'll check my connections again, clean the MAF sensor. I do not have a clamp on the intake tube at the throttebody, so maybe that's the problem.
Air fuel ratio looks good at around 14.7:1
ArmstrongRacingSan Diego · Oct 31, 2018#242Regarding the charging issue, I would follow this link and look at the image on page 62.
https://www.slideshare.net/crcs2009/...iring-diagrams The battery light means there is less voltage at the regulator diodes than the battery. Pins 1&2 should both have battery voltage with the ignition on, if not the alternator will not charge. The other white #1 is the large cable to the battery and that should also have battery voltage.
------------------
The MAF codes I believe, are referring to an incorrect signal back to the ECM. Double check that you have 12v at the CENTER wire on the MAF plug, that should be the wire you applied the add-a-circuit to. Check that there is no pinch or fray damage to the MAF harness.
------------------
I'm gonna check on the other code, that's confusing...I'll return to edit
EDIT: I looked over Brushforhire's and my own swap thread, and yes the only wiring required to correct the P2770 is that the Blue wire(pin 9) is grounded EXITING the control plug(not the wire coming from the harness). Double check that the crimp and attachment to the trans is solid.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 31, 2018#243 Originally Posted by
ArmstrongRacing ↑ Regarding the charging issue, I would follow this link and look at the image on page 62.
https://www.slideshare.net/crcs2009/...iring-diagrams The battery light means there is less voltage at the regulator diodes than the battery. Pins 1&2 should both have battery voltage with the ignition on, if not the alternator will not charge. The other white #1 is the large cable to the battery and that should also have battery voltage.
------------------
The MAF codes I believe, are referring to an incorrect signal back to the ECM. Double check that you have 12v at the CENTER wire on the MAF plug, that should be the wire you applied the add-a-circuit to. Check that there is no pinch or fray damage to the MAF harness.
------------------
I'm gonna check on the other code, that's confusing...I'll return to edit
EDIT: I looked over Brushforhire's and my own swap thread, and yes the only wiring required to correct the P2770 is that the Blue wire(pin 9) is grounded EXITING the control plug(not the wire coming from the harness). Double check that the crimp and attachment to the trans is solid.
Thank you Tom!
The blue wire comes out of pin 10 on my connector unless I'm reading the diagram incorrectly. The connector in this pic below comes from my scionXd wiring diagrams.
Picture not included in this copy I will follow up on your suggestions. Last night I went back out and unplugged and replugged the MAF sensor connector. I reset the codes and the only one that is returning is the P2770 code after 5 or 6 mintues of running. I had the battery connected with jumper cables to my van. Maybe it takes longer for the codes to set.
To add to this, my A/C compressor sounds really noisy, like a bearing is bad. It's like an unlubricated metal on metal sound.
I had so hoped that everything would be good on my startup. Looks like I still have some work ahead of me!
tmontagueCaledonia Ont. · Oct 31, 2018#244I'd double check your ground on the trans. Use a multimeter or test light and make sure it is a good ground. If that's good then check the wiring.
Glad to hear the rest of the codes cleared up. Congrats on the start up, dont be upset about a few bugs that need to be worked out, its par for the course
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 31, 2018#245Thanks you guys. You really take the edge off the worry. I have another thought. My CA2 connector may not be 100% seated. I recall it going in a bit hard and I taped it up too far, losing flexibility. Of course I'm at work and wanting to run out the door, go home and check it. I don't know if this has anything to do with the charging but I bet it might be the cause of the trans code. Probably all wishful thinking on my part, but nevertheless a place to check first.
tmontagueCaledonia Ont. · Oct 31, 2018#246When you get home use a tool to read voltage while the car is running and push on the connector or wiggle it, see the voltage changes.
Until then accept what is and let it go. You'll be more fresh when you get back to the car
atomic_hojiKincardine, ON, Canada · Oct 31, 2018#247Man, you're doing great so far! Only a few little hiccups.. 👍
Tom and Trevor have already noted good troubleshooting steps, but if you are having alt. problems the low voltage could very well be tripping up those other systems. Between that and checking your grounds and/or soldered and wire connections I think you'll be in good shape.
A/C could be pulley bearing? Could squirt some lube and see if it quiets - would need replacing long run. I don't recall, but you're sure you have enough oil in it?
Keep at it! And no need to cry, laughing is always better - even at the bad stuff; everything can be fixed (some things just make a bigger mountain.. lol). Swearing and hitting it sometimes helps makes you feel better, but I've found rarely helps - and often ends up hurting.. 😁
-- Adam
ArmstrongRacingSan Diego · Oct 31, 2018#248Can you post a picture of the xD transmission diagram to verify? I don’t have access to any.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 31, 2018#249 Originally Posted by
ArmstrongRacing ↑ Can you post a picture of the xD transmission diagram to verify? I don’t have access to any.
Hi Tom.
Here is a pic of my current connector with ground.
I'll post the requested diagram shortly - as soon as I figure out which one I need for you.
Picture not included in this copy Here is the diagram. I can send you the pdf if that helps. Thanks!
Picture not included in this copy atomic_hojiKincardine, ON, Canada · Oct 31, 2018#250Unless there's a trick with the autobox, pin 10 on your connector should run through the engine harness from the ECM to the transmission, not from ground to the transmission.
The way it looks right now is that the ECM will ask for S2 solenoid and I have no idea where the blue wire in the engine harness is, but if it's touching something it could be causing a ground fault. What the ECM wants is to power output S2 and energize the coil - power from ECM, through a coil, to the ground in the ECT solenoid box.
At least that's how I interpret it..
edit: looking at my Gen 3 diagram the pins on C29 connector for the xD match the Yaris' autobox inputs i.e. pin 1 on the xD connector pairs to THO; pin 2 to ST; ...; pin 9 SLU-; pin 10 S2. Only pin 7 should be blanked/empty.
-- Adam