Replies continued
tmontagueCaledonia Ont. · Oct 20, 2018#151Yes for sure do what Tom said. I researched this before I swapped the engine in and found it was a weak spot for leaks. I purchased the oem on ring and new OEM plate for not much money and swapped that in before I put the engine in.
It can be done fairly easily with the engine in the cat but you would probably want to remove the wiper cowling so you can see what you are doing
Edit - I also did this on my wife's 1zz in her Vibe so I may be confusing this with my 2zr but I'm pretty sure I did this on my engine as well. Regardless I have no leaks
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 20, 2018#152Thanks Trevor and Tom. I will look into the plate in the timing cover and see what I'm looking at for eta on parts. I will also remove the wiper shroud.
Today I removed the oil cartridge cover. It was a beeotch to get off even with the filter wrench I picked up today - which, incidentally, doesn't fit tight to the bottom of the cover. Must be a cheap knockoff and very slightly too small. But, it does work. Anyhow, I recovered a couple ounces of used oil. It was dark but very fluid and slippery, no grit. I strained it with a very fine strainer and there was nothing at all in the oil. The filter looks good, and similar to pics I've seen online (many look a little crushed). The pleats were pretty much spotless.
Picture not included in this copy
I did a Lubricheck test and was very thrilled to see a reading that indicated the oil was still in good condition. I think Lubricheck is considered by those in the know - such as many from Bob Is The Oil Guy - to be a reasonable tool to assess the condition of engine oil. Not a Blackstone or similar lab UOA but still far from a snake oil type of deal, I believe. Regardless, it makes me feel good. 🙂 I've used it over several oil changes and it does reflect what one might expect of oil condition. Fresh oil gives me a "1" and after 7K - 8K km, it will read in the "6" - "7" range. And, the results seem to have good repeatability, providing that the sensor is impeccably clean.
Here is the Lubricheck tool. For some reason I can't orient these pics north/south despite trying.
Picture not included in this copy
And, here is the reading, "7", from the used sample
Picture not included in this copy
Given the visual condition and cleanliness of the oil, the Lubrickeck result and the clean filter, I have convinced myself that there shouldn't be any major engine issues.
Finally, I did change the plugs out. I figured I'd grab them @$14.00 each from Canadian Tire. Well, also to briefly escape 5 pumped-up-on-sugar 8 yr old girls and son (Daughter's B-Day party). My wife and I took turns.
Here are the plugs. There were a few different numbers along with these. These are identical in dimensions though appear to have a very, very slightly larger gap. Though, these are the 4711 TT (Twin Tip) Iridium plug that Denso flogs as providing more power, torque (yeah, right lol). The original ones appear to be the 3444 plug. I understood that these new plugs come pre-gapped. Maybe I should remove them and check the gap, though I haven't had to gap plugs in years.
Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 21, 2018#153I went out to check the timing cover window you guys mentioned and found what looks like part of the timing cover gasket pinched out. It looked like there has been a very small leak. A lot of what you see, moisture-wise, is Releasall penetrant I sprayed for the window bolts but it looks as though there has been some oil leaking. Not sure if it is actually from this cover or the actual timing cover seal. On close inspection, there looks like there is still some seal between the block and timing cover.
Is it likely that this seal was improperly installed at the factory? I can say that the idea of removing all the pulleys, timing cover is something that I really, really don't want to do.
Picture not included in this copy
I also loosened all the bolts for the intake manifold so I can replace my pcv valve. I soaked them with Releasall but they still came off quite hard. It should be an easy removal now.
Timing Chain Tensioner
Had a bit of a scare after removing the tensioner as I couldn't get it back in. A quick youtube video explained that you compress the tensioner (pre-load it), and hold it with the little hook. It's supposed to release by itself once the timing chain slaps it. If you slightly squeeze the plunger, the hook does pop right off. Fingers crossed that it actually does release, put tension on the chain and the timing chain stays in the correct spot on the timing gear! EDIT: The pre-loaded tensioner mechanism releases when you turn the crank. You can hear it click. To be sure, I removed and re-installed twice.
Have to source a gasket but having a little trouble doing that at atm. EDIT: Looks like Toyota Part#13552-0T020 The one on there is pretty darn thin. I think I'll use some RTV too.
Picture not included in this copy
Intake Removal and PCV Valve
Took the intake off to access the PCV valve. I cleaned up the aluminum mating surface on the engine. It was a tad dirty.
Picture not included in this copy
The pcv valve had typical light carbon on it but it jiggled freely inside and the spring worked well. Since I'd have to order a new pcv valve - no one locally stocks them and it's likely a special order item - I thought I'd clean it up and reinstall. I soaked it in lacquer thinner and within seconds it was spotless; all traces of carbon disappeared. Strong solvent! Put a little teflon tape on it and reinstalled. If the pcv valve does fail, it looks like not too bad a job with the engine in the car - then again, it might be really tight with the 2ZR in the Yaris. 🤷
Picture not included in this copy
Picture not included in this copy
tmontagueCaledonia Ont. · Oct 21, 2018#154The sealant that actually seals is the stuff sandwiched between the 2 mating surfaces and not what gets squished out. There should still be more than enough RTV between the 2 surfaces from the factory. I would be astonished if the factory messed that up so unless someone else removed the timing cover then it should be fine.
It is likely an issues from the chain tensioner gasket. I'd recommend just replacing that, giving it a good cleaning and seeing if it ever leaks again.
That said, it is almost impossible to replace the timing cover while the 2zr is in the yaris and it is so much easier when it is out of the car. Either way it is never a quick easy job so I'd just leave it and trust that the timing cover deal is still good
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 21, 2018#155 Originally Posted by
tmontague ↑ The sealant that actually seals is the stuff sandwiched between the 2 mating surfaces and not what gets squished out. There should still be more than enough RTV between the 2 surfaces from the factory. I would be astonished if the factory messed that up so unless someone else removed the timing cover then it should be fine.
It is likely an issues from the chain tensioner gasket. I'd recommend just replacing that, giving it a good cleaning and seeing if it ever leaks again.
That said, it is almost impossible to replace the timing cover while the 2zr is in the yaris and it is so much easier when it is out of the car. Either way it is never a quick easy job so I'd just leave it and trust that the timing cover deal is still good
THANK YOU, TREVOR! Not only are you guys providing me with invaluable technical info but you're helping with my confidence level too! I greatly appreciate it.
ArmstrongRacingSan Diego · Oct 21, 2018#156That looks like the classic plate leak we mentioned, because the engine leans aft a bit when installed all of that leaking oil travels along the head gasket at timing cover seams. Replace the plate gasket and clean it like Trevor mentioned, and you’ll never see another leak.
Sealer squeezed out of that part of the chain cover because it’s a 3-way joint, and the manual requires extra.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 21, 2018#157 Originally Posted by
ArmstrongRacing ↑ That looks like the classic plate leak we mentioned, because the engine leans aft a bit when installed all of that leaking oil travels along the head gasket at timing cover seams. Replace the plate gasket and clean it like Trevor mentioned, and you’ll never see another leak.
Sealer squeezed out of that part of the chain cover because it’s a 3-way joint, and the manual requires extra.
Awesome! Thanks Tom! I will replace the gasket. Off to source said part now...
EDIT: Timing tensioner gasket is
Toyota Part#13552-0T020 06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 22, 2018#158AC Discharge Today.
Picture not included in this copy
ArmstrongRacingSan Diego · Oct 22, 2018#159Very exciting times await....
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 22, 2018#160Lifted Up
Saturday looks like the day for the swap. During the week I am going to remove front, wiper cowl, air box, battery etc. My plan is to spray the bell housing bolts and other bolts with Releasall daily until Saturday. I'll also pick up a can of mapp gas in case I run into any stuck bolts.
Picture not included in this copy
tmontagueCaledonia Ont. · Oct 22, 2018#161Good luck! I spent a few hours the evening before the swap to rip off all the front end stuff. This allowed me to "start" my swap getting right into the engine which I felt was a great plan
I also drained all the fluids and what not so the first official day was me figuring out exactly how to get the engine out
ArmstrongRacingSan Diego · Oct 22, 2018#162 Originally Posted by
tmontague ↑ Good luck! I spent a few hours the evening before the swap to rip off all the front end stuff. This allowed me to "start" my swap getting right into the engine which I felt was a great plan
I also drained all the fluids and what not so the first official day was me figuring out exactly how to get the engine out
Trevor your ability to get this done in one weekend AND all of the great content you’re providing is pushing me to encourage YOU to do a “Yaris engine removal” tutorial
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 23, 2018#163 Originally Posted by
ArmstrongRacing ↑ Trevor your ability to get this done in one weekend AND all of the great content you’re providing is pushing me to encourage YOU to do a “Yaris engine removal” tutorial
Amen! That was a major feat doing that by yourself! I can only imagine trying to work under the car, lining things up and having to move back and forth from underneath to your engine hoist. I think you had a jack underneath too, correct?
Thanks gents!
Ah, yes, I'm glad you mentioned the fluids Trevor. It reminded me that I have to empty my oil drain pan, which has been sitting full for the past couple weeks. Fortunately, my neighbour has large drums for waste oil, coolant etc. We have a good arrangement going. I borrow some tools from him etc and I undercoat his vehicles for him at our shop.
When I was out under the car yesterday, I was musing about how nice it would be to be able to drop the engine in without disturbing the transmission lines, but obviously that's not going to be possible with having to remove the rad. I think it would be far too big a risk trying to get the engine down into the bay even with the wiper cowl removed.
My major concern now is effectively getting all of the bell housing bolts off without breaking them. This is a 2006, winter driven car. Any advice you guys are willing to give, would be great. And, Trevor, I haven't forgotten your advice to remove the trans with the engine and I think I will do that if I encounter any issues with bolt removal. It would no doubt be easier to attend to stuck bolts out of the car.
As I move forward my current 'wondering' is how the A/C lines will need to be modified to adapt to the Corolla compressor.
Finally, I never managed to source engine hooks. Here is a question:
Will this tab on the cylinder head be strong enough to lift the engine? I am hooked to the mount at this point but that may be in the way of attaching the driver's side bracket. The current diagonal placement provides a pretty level engine.
The other option is to fabricate some hooks in our shop as we have lots of flat stock, drill presses and metal benders.
Picture not included in this copy tmontagueCaledonia Ont. · Oct 23, 2018#164In the next 2 years once my family moved into a house with a garage and I get a dd'r beater I plan on making some 2zr videos with some good DIY guides. Problem is I'm always in a rush when I work on my car so I only have the time to do a quick post on weird things I noticed for any who do it in the future.
One of the main reasons I could do the swap as quick as I did was because of the outlines and threads posted from those that did the swap before me and wrote down and took pics of everything. It was a huge help.
It was a tough job with no hoist. Hardest part was the multiple times of getting up and down from underneath the car, made me very sore in the neck and core for the next few days.
I personally would not lift the engine from those tabs, especially when it is the engine and trans convo, that's about 300 lbs total ( 200 from engine and 100 from trans)
The oem hooks are very specific as they have a 1.5" spacer to allow you to bolt it to the head but clear the head at the same time. It would he tough to fabricate without having the oem hook in hand.
Use the engine mount and header or intake manifold and header. Just keep the contact point close to the block as you can so it reduces the moment arm and torque on the part you are hooked to.
You can then put a jack underneath to support it when you need to unhook from the mount to install the engine. You can use a different area when you unhook from the mount as you went be lifting the engine much once it's ready to be bolted to the mounts.
The bell housing bolts were no issue for me but if you'd like you can spray the backside with penetrating fluid. You have back access to most.of the bell housing bolts so you can spray the threads from behind. But like in said they all came out fine. As always i reinstalled with anti seize and hand tightened
atomic_hojiKincardine, ON, Canada · Oct 23, 2018#165+1 on not lifting via the tabs - I think you'll risk breaking them while shoving the engine + transmission around. The factory lifting hooks work well in terms of weight bearing, but I found using a single direction, basic load leveler (as opposed to a 2-axis lifting frame) caused it to roll front-back as well as side-side when trying to make adjustments. I ended-up slinging the transmission side to the transmission mount bracket and using a two-point attachment on the front - the factory hook to the intake side and a loop of chain bolted into the block on the exhaust side. Speaking of which - the intake is plastic, I wouldn't risk slinging through it either.
Just remember when you get into it, there are items that have to work, and there are things that are nice to work; i.e. A/C. 😁
w.r.t. bell-housing bolts - as Trevor said some penetrating fluid on the backside (thread) and if that doesn't give them up the torch on them should do the trick I would imagine. Being different metals they will expand at different rates; heat up, cool with some penetrating fluid, should de-crust it enough to pop them loose I'd imagine.
Awesome work getting setup so far! 👍 Can't wait to see you dive into it.
-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 23, 2018#166Thanks gents! I will refrain from lifting on the tabs. That said, yesterday, I did lift the engine by that tab and the mount,, but just up in the air and quickly back down. I can't see having the actual lift hooks by the weekend as I haven't actually been able to ascertain the correct part number. Even if I did, I won't have them in time to do the job. So, I'll have to come up with another work around. I'm not going to trust my thin green tiedown straps, so will find heavier strapping for this application.
I am going to try to leave the transmission in the car, slide the engine down in and bolt it up. This may not be the best approach, but it's the one I'm most comfortable with for a couple of reasons: 1) I'd rather deal with fewer mounts, 2) I shouldn't have to deal with axles, risking seal damage 3) I'll be dealing with less overall mass 4) I'd like to see if I can pull it off.
It has, I know, been a long build-up to my swap. I am super pumped to dig in to this. Further to your comment, Adam, about things that 'have' to work vs those that are 'nice' to work, haha, I've already prepared myself for any eventualities there. I will of course be dogged in my pursuit of eventually having everything work! My cruise control is definitely a wild card.
I picked up my timing chain tensioner gasket, a tube of black RTV as well as 3 quarts of WS (I have another 2 in the garage) and two Carquest oil filters that are Korean-made and look quite well made. Heading out to the garage now to install the filter and tensioner gasket! (Both done now)
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 24, 2018#167Flip Fuel Line Around
Here is a pic from Tom's swap thread. Just trying to get a sense of what's involved in flipping the fuel line around. First, is it line 1 or 2 as labeled in the pic below? And is it flipped end for end or flipped vertically? My Corolla engine already has the fuel lines attached. Or, are we talking about the rubber hoses in this instance?
Thanks!
Picture not included in this copy
ArmstrongRacingSan Diego · Oct 24, 2018#168You don’t mess with any of the metal lines. The plastic fuel hose that connects the engine to the car is what needs to be turned around. It’s a strange “S” shaped hose with quick disconnects on each end(blue release buttons on the fittings).
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 24, 2018#169 Originally Posted by
ArmstrongRacing ↑ You don’t mess with any of the metal lines. The plastic fuel hose that connects the engine to the car is what needs to be turned around. It’s a strange “S” shaped hose with quick disconnects on each end(blue release buttons on the fittings).
Ah, I see. Perfect. Thanks!
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 24, 2018#170Help! I may have run into a snag. Here is what I posted in brushforhire's 2ZR swap thread. I'm not sure if he is around anymore.
Hi brushforhire. I am hoping that you can help me here as I'm almost ready to do my engine swap. I am keeping my Yaris transmission but, of course using a Scion xD harness. I think I have all the other wiring figured out except the trans ground for the yaris.
Your pic is below. You indicated that the hole immediately to the right of the solid blue wire would be used for ground to block. That would be "9", correct.
Picture not included in this copy
Here is my Yaris connector. Hole "9" is aready occupied. Can you tell me which hole I should use for the ground?
Picture not included in this copy
Thank you very much in advance.
Adam
tmontagueCaledonia Ont. · Oct 24, 2018#171Use a test light to check if the empty spot on your connector is a ground. Hook the one end of the test light to the positive on the battery and the pointy end to the pin in that hole.
Iirc tom ended up just grounding the wire to the trans block at there was a threaded hole somewhere on it
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 24, 2018#172 Originally Posted by
tmontague ↑ Use a test light to check if the empty spot on your connector is a ground. Hook the one end of the test light to the positive on the battery and the pointy end to the pin in that hole.
Iirc tom ended up just grounding the wire to the trans block at there was a threaded hole somewhere on it
Thanks Trevor. The pic I posted above is actually the Yaris harness connector - still on my Yaris engine, but my xD harness also has a wire already in the pin that is supposed to the ground wire as per bushforhire's explanation.
I have a multimeter but not a test light.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 24, 2018#173Some Progress
I have drained all the fluids. I drained the ATF into an old ice cream bucket that I marked off in liters so I can replace the same amount when done. Removed the front, rad hoses, rad, ac lines, transmission lines, starter, airbox etc. Great news is that all the bellhousing to engine bolts are breaking free fairly easily. It looks as though the Releasall made its way quite deep into the threads.
I still have to remove that large cross member in the front but am soaking those bolts in penetrant as they are a bit rusty. Or, should I leave that crossmember as it's a major structural member? I'll take off the wiper tray tomorrow as well as the battery and tray, take out the torque converter bolts. Time permitting, I'll disconnect the exhaust from the manifold.
Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 24, 2018#174Help Identifying this missing hose...
Here is the pic of the engine before it was shipped to me.
Picture not included in this copy
Here is the pic of my engine with the hose missing. Not sure where the hose that attaches to this fitting runs to or what it does. I assume it's some kind of vacuum hose. I couldn't find anything on the engine that it would attach to. Maybe the intake tube? Brake booster? Any help would be appreciated. Thanks.
Picture not included in this copy
ArmstrongRacingSan Diego · Oct 25, 2018#175That blue wire coming out of you xD harness shift control plug should be cut about 8" from the plug and grounded to the transmission case. If you would have scrolled down further on Brushfohires post you would see that.
The hose that's missing is still there....its just hanging down by the throttle body. It must have accidentally been pulled off the port.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 25, 2018#176 Originally Posted by
ArmstrongRacing ↑ That blue wire coming out of you xD harness shift control plug should be cut about 8" from the plug and grounded to the transmission case. If you would have scrolled down further on Brushfohires post you would see that.
The hose that's missing is still there....its just hanging down by the throttle body. It must have accidentally been pulled off the port.
Thanks Tom! I am confused (happens easily 🙂) about this blue wire because Sam says explicitly not to cut the wire and ground it. He indicates that the picture is wrong in his post and that a wire needs to be added to hole 9 next to the blue wire.
I feel quite silly about missing that hose. I think it's just me missing things trying to keep everything straight in my mind as I disassemble and reassemble stuff.
tmontagueCaledonia Ont. · Oct 25, 2018#177Remove the cross members to give yourself more space. They are only structural when in a front end impact.
And as Tom said, the hose is right beside the port in the picture
ArmstrongRacingSan Diego · Oct 25, 2018#178The pin swap was only applicable to using a corolla harness, and that took place at the large ECM connector. The xD harness only needs the blue wire grounded like in the picture
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 25, 2018#179 Originally Posted by
ArmstrongRacing ↑ The pin swap was only applicable to using a corolla harness, and that took place at the large ECM connector. The xD harness only needs the blue wire grounded like in the picture
THANK YOU, Tom! I think I'm just confusing myself. I've been staying up too late the last few nights too, so certainly not working at max cognitive capacity. Haha. Still on schedule for Saturday. Got the crash bar, battery and battery tray out. Will try to go out tonight to take the hood and wiper cowling off and maybe the torque converter bolts.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 25, 2018#180 Originally Posted by
tmontague ↑ Remove the cross members to give yourself more space. They are only structural when in a front end impact.
Removed it, Trevor. Because I have the foglights, the body harness (I think) is still in the way but can be moved up or down a bit. I didn't trace the harness back on the passenger side, so maybe there are just a few connectors to remove and I can pull it out of the way.
tmontagueCaledonia Ont. · Oct 25, 2018#181You can probably unplug some connectors and pull it of the way. I don't have fogs so I never had that issue. That said if you decide to leave the harness in place be super careful with the engine as it won't take much to rip the connectors out
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 25, 2018#182 Originally Posted by
tmontague ↑ You can probably unplug some connectors and pull it of the way. I don't have fogs so I never had that issue. That said if you decide to leave the harness in place be super careful with the engine as it won't take much to rip the connectors out
Yes, I think I found the end and it is at the oil pressure sensor... I think. So tomorrow, I will get that all out of the way.
I removed the wiper tray and only broke one bolt doing it. It's one of the middle ones and nothing to do with the wiper motor assembly, so I will probably drill it out and use a self-tapping screw. The only other bolt that broke was on one of driver's side engine cover up at the top. Same fix there, I guess. Glad I removed the wiper tray as well as you can't disconnect the ecu plug without moving it out of the way. That little securing arm bumps into the wiper tray and won't open all the way.
Taking the hood off was anxiety-ridden as I had to sort of balance it with one hand and take the last bolt out with the other. I so don't want to injure my new paint job LOL.
I got the fuel lines off fortunately and the system had lost pressure after several days of not running and the battery being disconnected.
Well, I now have tons or room to work. I can say though that I'll probably be bugging you guys with a few questions pertaining to hooking all the hoses back up. It may take a little longer but rather than bag up all the bolts/hardware, I'm just putting the bolts back into their holes. That way hopefully I won't lose any.
I'm adjusting my plan and I think I'll remove the intake and exhaust manifolds for a couple reasons: 1) Easier access to the bell housing bolts around the intake and throttlebody and more clearance with the exhaust manifold removed.
How the HE double hockey sticks, did you do this job in two days in your driveway??? 🙌 Everytime I look at the mess of spaghetti in that engine bay, I'm sure my stress level elevates a bit. I really hope I can get this back together and that says nothing about troubleshooting potential problems after the swap - a.k.a. a no run situation.
Here is the current state...
Picture not included in this copy tmontagueCaledonia Ont. · Oct 26, 2018#183Good progress so far!
What helped the most in being able to take the swap in a weekend was spending hours and months reading through the other swap threads. I then visually went through all the steps I needed to complete and if any infi wasnt clear I made sure to find the answer. I placed all the parts and harnesses out previously and visualized how it would all connect on the engine. I then connected it before the install.
And of course what really helped was the fact that if I didn't have it done in 5 days then I was screwed as I had to get back to work and class so there was a lot of pressure which i wouldn't recommend.
Dont get too over whelmed by the mess, once the engine is back in place just look at following the hoses one by one and figuring out what hose is what and where it needs to connect. Taking pictures helps a lot too
ArmstrongRacingSan Diego · Oct 26, 2018#184Yeah, I’m still impressed too. With how so many great, knowledgeable guys we have spread across the world, NO ONE will have to take their car to a shop. We have the manuals, you can buy techstream, so all anyone needs is a/c and alignment.
tmontagueCaledonia Ont. · Oct 26, 2018#185^was cheaper for me to buy cheap ebay manifold gauges and vacuum pump then to have an a/c guy do it for me. I've already used the gauges a bunch and topped up my 12 year old family cars. Well worth it to have those lying around
ArmstrongRacingSan Diego · Oct 26, 2018#186That’s awesome.....
Make a diy yet? ;-P
tmontagueCaledonia Ont. · Oct 26, 2018#187There's more than enough great videos on YT explaining the whole process- ChriFix has probably one of the best. Since it's there is nothing specific for the Yaris I haven't bothered
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 26, 2018#188 Originally Posted by
tmontague ↑ There's more than enough great videos on YT explaining the whole process- ChriFix has probably one of the best. Since it's there is nothing specific for the Yaris I haven't bothered
YES! I watched that ChrisFix video after having the guy come down and discharge my system. I may yet buy the manifold gauges and pump which can be had for ~$90.00 on eBay. If I do this, I'll just go pay the guy for his time discharging my system.
The plan is to get started on the swap tomorrw morning. Will post progress shots.
Check out my new goodies that just arrived today!
New muffler. Should look dope, with those two 3" pipes sticking slightly out the back. Hopefully not too big looking.
Picture not included in this copy Picture not included in this copy Gonna need one heck of an adapter. 😲
Picture not included in this copy New OEM mount. So much more substantial than the other POS I had.
Picture not included in this copy tmontagueCaledonia Ont. · Oct 26, 2018#189Fyi - r134 refrigerant is illegal to buy in Canada w/ out a license but south of the border you're good to go. I stock up on some cans of Dupont r134 when ever I head over to pick up some car stuff
Oh, and save yourself future a/c system hassles, install an ounce of refrigerant dye to your system when you recharge it. A black light will make a leak easily detectable in the future
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 26, 2018#190 Originally Posted by
tmontague ↑ Fyi - r134 refrigerant is illegal to buy in Canada w/ out a license but south of the border you're good to go. I stock up on some cans of Dupont r134 when ever I head over to pick up some car stuff
Oh, and save yourself future a/c system hassles, install an ounce of refrigerant dye to your system when you recharge it. A black light will make a leak easily detectable in the future
Ah, I see. So obviously you recommend R134 over the 'Canadian' equivalent? Why so? Thanks for the recommendation on the dye. I also have to get PAG46 (3.5 oz). Some of it comes with the dye in it I believe.
Thanks!
tmontagueCaledonia Ont. · Oct 26, 2018#191The canadian stuff sold at CT is propane based and explosive, also technically not what is in cars from factory. Use the proper factory stuff if you have the means it is what the compressor and the whole system uses in all NA cars. The CT stuff came out as a way for shade tree mechanics to "fix" a/c systems
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 26, 2018#192 Originally Posted by
tmontague ↑ The canadian stuff sold at CT is propane based and explosive, also technically not what is in cars from factory. Use the proper factory stuff if you have the means it is what the compressor and the whole system uses in all NA cars. The CT stuff came out as a way for shade tree mechanics to "fix" a/c systems
Done! I will pick up some R134A when I'm across the border - probably early next week.
I read an article on recharging the system and it said if the stsyem has been evacuated, to add oil to the compressor, plus some for the lines, plus a bit more for the dryer. Would 6 oz be acceptable? Not sure how sensitive the system would be to over-filling with oil. Do you recall how much you put in?
tmontagueCaledonia Ont. · Oct 27, 2018#193Ouch 6oz seems like way too much. I've read different things but my understanding is that most of the oil sits in the compressor so you dont need to add any if the compressor stays.
My new reman'd compressor had oil in it when it was shipped. I never added any oil, just dye and r134. Haven't had an issue since
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 27, 2018#194Engine Out! Will post up progress pics later.
Picture not included in this copy
Picture not included in this copy
tmontagueCaledonia Ont. · Oct 27, 2018#195Nice!
ArmstrongRacingSan Diego · Oct 27, 2018#196I would check the compressor you bought, if it has oil in it you’re fine. You only need to consider what’s in the lines if you replace them too, add the dye and verify the new compressor has oil.
Great work so far!
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 27, 2018#197Engine In...But, Not Without Issues...
Despite many maneuverings of the engine and transmission, we could not get the engine in without removing the pegs in the transmission. That of course caused alignment problems with the bellhousing and I am now struggling to get everything lined back up. Trevor, you now have exclusive rights to say, "I told you so" 😆. I probably should have removed the trans and bolted it up out of the car. I have 4 bolts on the bottom 2/3 inserted and the bellhousing is completely flush with the engine. It feels like one bolt has started to cross thread and one other I can't get started at all. Open to advice. I'm keeping everything loose for now and will continue to try tweaking the engine and trans to get those bolts in.
EDIT - Got the bell housing bolts in with some finagling. There wasn't a cross tread, but more likely the bolt just dragging on the side of the housing. The bolt I couldn't get started actually didn't belong in the hole I was trying to thread it into. Thank god for the pics I'd taken before!
After a short break, I'm going out to put the torque converter bolts back in. Have to check the torque spec on those now.
Anyway, here is a pick of the engine in the car.
Picture not included in this copy
ArmstrongRacingSan Diego · Oct 27, 2018#198The alignment is a bit tricky for sure. But you definitely shouldn’t remove the alignment pins. I remember having to fight with it for a while and I had a second hand to help.
Take a step back and see where the flanges are not exactly flush, try to correct that and line up the bolt holes
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 27, 2018#199My helper, Josh. He's a student at our school and he's planning to pursue a career in the automotive industry. I asked him because he is careful and a good troubleshooter. He liked the idea of having his pic on yarisworld.
Picture not included in this copy
Torque converter bolts coming off
Picture not included in this copy
The old faithful 1NZ ready to make its departure.
Picture not included in this copy
Big hole welcoming the 2ZR.
Picture not included in this copy
2ZR moving in.
Picture not included in this copy
Big brother and little brother.
Picture not included in this copy
Brain transplant.
Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 27, 2018#200 Originally Posted by
ArmstrongRacing ↑ The alignment is a bit tricky for sure. But you definitely shouldn’t remove the alignment pins. I remember having to fight with it for a while and I had a second hand to help.
Take a step back and see where the flanges are not exactly flush, try to correct that and line up the bolt holes
Thanks Tom. Ultimately, I got everything lined up and the bolts back in. The mating surfaces are in full contact around the whole perimeter. We had tried a dozen different things but we could not get the flex plate past those pins no matter what we did - tilting, wiggling, leaning, lifting and lowering the trans a bit. It was hitting the frame on the passenger side. Once the pins were gone, it slid down and in but still very tight. I really didn't want to take them out as I knew it would cause alignment issues. But, everything seems ok now. I hope! Thankfully, there's enough room on the passenger side to change the belt out when needed.
The above said, I would never say that it is not possible to drop the engine in beside the transmission with the alignment pins in. We just couldn't make it happen ourselves.
I would also remove that pesky exhaust manifold as it was a royal pain in the butt.