Yarisworld Archive

06YarisRS's 2ZR-FE Swap 5-Door Hatchback (Automatic Transmission)

448 posts · 301,527 views · page 1 of 9

06YarisRSOriginal postFredericton, New Brunswick, Canada · Sep 25, 2018#1
I have decided to give the swap a go. It is definitely beyond the scope of anything I have done mechanically, but I've aways wanted to change an engine and what a great bonus to be able to put a different and more powerful engine in a car. From what I gather, I'm in for an 'easier' swap as I plan to keep my auto transmission and my car is a pre-immobilizer build.

I have read all of the swap threads here on Yaris World by armstrong, tmontague, crankyoldman, atomic hoji, brushforhire several times, extensively searched the internet and read anything I could find about this swap, spoken to folks from NY to CA looking for parts.

By nature, I tend to overthink things. Naturally, I am appealing to the patient understanding and gentle nature of all those who have proceeded me in this worthwhile endeavour. 😁


I have started to accumulate parts. Please, please let me know right away if you see anything amiss in my parts selections.

I started with the right side motor mount. Being frugal and all, rather than spend a couple hundred USD (over $400.00 in Canada) on a new OEM one (couldn't find a used one anywhere), I bought a new knock off mount (~$32.00 USD) and a used bracket (~$25.00) and associated bolts. I hope I don't come to regret the purchase of the mount, but it is surprisingly sturdy and seemingly well made.

Here is a link to the mount, but I take no responsibility if it ultimately turns out to be a piece of crap. Keep in mind that you'd have to source the bracket elsewhere. Also, note that there is no rubber cover on the mount. I'll try to fabricate and attach some kind of rubber cover. Or, just buy the actual OEM part complete with bracket. [UPDATE: DO NOT BUY THIS MOUNT, IT IS JUNK]

https://www.ebay.com/itm/Right-Mount...72.m2749.l2649

Picture not included in this copy

Edit (29 Sept) Mount with a little paint and bent bolt. I think the bracket was removed from the car with a backhoe. A chunk of the mount came along with it. Can't find a part number for the bolt as it's part of the whole OEM unit, so I'll take the bolt to a local auto parts store and match it up.

Picture not included in this copy

A 2010 Scion xD Airbox, tube and MAF sensor
Picture not included in this copy

Airbox with a little TLC. Washed the box and removed rusty clamps/hardware, soaked them overnight in phosphoric acid, and a couple coats of cured VHT Flameproof. I hate rust.

Picture not included in this copy


I will be buying my engine (looking at a 2012 Scion and a 2011 Corolla, both with low 40K miles) , ECU and harness within a couple of days. After that, A/C compressor and alternator. The Scion will need a throttlebody as that was scavenged, the Corolla would need the timing cover bracket (Part# 12315-37040) and associated hardware.

My first technical question: In Tom Armstrong's swap thread, it refers to a 2008 - 2009 Scion xD ECU. As mentioned, I am looking at a 2012 Scion engine, ECU and harness all out of the same automatic car. Will the 2012 ECU work? or should I be looking for a 2008 - 2009 only ECU?

My second technical question Most of the used ECUs I looked at say that reprogramming may be necessary. Is this only related to the immobilizer? If I don't have an immobilizer, will the ECU be otherwise plug and play?

There is no definitive timeline on this project and I will have to try to make time around kiddie sports schedules/ family committments etc, though those have never really stopped me in the past. 😆

I will do my best to post pics and explain what I've done - including any and all blunders - as I go.

I'm going to add pricing to give people an idea of what it might cost in US dollars. I'm not including part numbers until I can confirm that they are indeed the correct part and function as I hope they do.

Items Purchased and Pricing (USD): I will keep adding to the list as I make my purchases.

New xD Passenger Side Mount* $31.38 (pic in this post) [I REPEAT: DO NOT BUY THIS MOUNT, IT IS JUNK]
2009 xD Passenger Side Mount Bracket** $35.00 (pic in this post)

New OEM Passenger Side Mount (12305-37091) $181.00 shipping included
2010 xD Airbox, Tube and MAF sensor $85.00 (pic in this post)
2008 ECU (Automatic) $17.59 (pic in post# 6)
2011 xD (Automatic) Engine Harness $140.00 (pic post#16, #76)
2011 Corolla 2ZR-FE $700.00 (pics in post #17, #75, #84)
New Timing cover mount bracket + hardware $107.00 with shipping (parts list in post#18)
2011 Corolla 1.8L alternator (local yard 42 000 kms) $58.06 (pic in post #41)
2010 Corolla A/C compressor $89.74 (pic in post #135)

Scion xD extra parts for:
Alternator, Radiator and engine mounting $73.39 with shipping (parts list post#32, post#114)
Scion xD mipdipe (Aftermarket - Eastern Catalytic) from Rock Auto $324.00
2014 Corolla Engine Cover - $19.30 (pic in post#118)


Running Total $1795.08

* This mount is not the full OEM mount of the same part number. It is missing the bracket.
** I could not find this part anywhere other than eBay.

Replies 447

ern-dizCA all day · Sep 26, 2018#2
Subscribed!
atomic_hojiKincardine, ON, Canada · Sep 26, 2018#3
Awesome! 👍 Congrats on taking the plunge!

Good score on those parts, I had very little luck when I was searching for the brackets, etc.. and just ended up buying from an online dealer. The airbox I did find actually cost as much or more than a CAI kit! 😲

Originally Posted by 06YarisRS ↑
...

My first technical question: In Tom Armstrong's swap thread, it refers to a 2008 - 2009 Scion xD ECU. As mentioned, I am looking at a 2012 Scion engine, ECU and harness all out of the same automatic car. Will the 2012 ECU work? or should I be looking for a 2008 - 2009 only ECU?

My second technical question Most of the used ECUs I looked at say that reprogramming may be necessary. Is this only related to the immobilizer? If I don't have an immobilizer, will the ECU be otherwise plug and play?

There is no definitive timeline on this project and I will have to try to make time around kiddie sports schedules/ family committments etc, though those have never really stopped me in the past. 😆

I will do my best to post pics and explain what I've done - including any and all blunders - as I go.
Not having done the swap on a 2nd gen. I'll take a stab at this, but suspect one of the 2nd gen. guys will chime in.. If you haven't already, get the wiring diagrams for any and all models you are using - your Yaris, the Scion xD, and the Corolla. It will make life so much easier to know where the differences might bite you; which will inevitably happen.. lol

1. If you have everything from the 2ZR-FE and your Yaris uses the same autobox then I imagine the 2012 Scion xD ECM will work; small differences in connectors, etc.. can be confirmed via wiring diagram. The weirdness with the xDs starts in 2013 - when looking up parts you'll find 2008 - 2012, the 2013/2014s are often not listed. BUT, the engine harness will match the ECM, obviously, you just need to match the body harness to the ECM - again, I suspect you're ok as the weirdness starts post-2012..

2. The immobilizer and the VIN is the only "reprogramming" that come to mind. If you're getting the ECM Canada side and your Yaris doesn't have an immobilizer, just ensure that the 2012 ECM is also non-immobilizer. Since your Yaris doesn't have the immobilizer key and ECU to talk to the xD ECM, the xD ECM won't get a valid signal to allow the engine to start. I believe the guys who are running non-immobilizer ECMs have a work-around to avoid the immobilizer equipped Yaris' to talk to the non-immobilizer ECMs, but I'm not aware of a way to trick the immobilizer ECM into starting with a non-immobilizer vehicle... immobilizer-mobilize-mobile... too many immobilizerers... Anyhow, hope that makes sense... 😁

Looking forward to seeing your progress!

-- Adam
tmontagueCaledonia Ont. · Sep 26, 2018#4
Welcome aboard!

No ecu reprogramming needed as long as you get a non immobilizer ecu. I reprogrammed the ECU VIN to match my original chassis vin so that less red flags were raised when it comes to e test out here in Ont. But it's not needed.

A 2012 should be fine as stated above as long as your it is a non immobilizer ecu.

The 2zr is a darn fine engine it is stupid reliable and has good area under the curve on a dyno- Toyota did well with this one I'm sure you will enjoy it.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 26, 2018#5
Thanks gentlemen! To pick up on a few points... Adam, thanks for the advice on the wiring diagrams. I will try to find those. You mention body harness? I thought that all I was concerned with was the engine harness. I know about the MAF requiring an alternate power source and the speed sensor wires that need to be switched over to the xD harness. I'm sourcing all parts for my non-immobilizer auto Yaris in the USA and will buy a 2008 - 2009 ECU (89661-52F71). The harness is where I'm struggling now.

From my research, the xD came in both auto and manual transmission. I have been unable to confirm if there is any physical differences between the harness for manual and automatic. I expect the plugs for transmission might be different? Every part number on eBay goes like this: 648.SC1D11 (with what appears to be the last 2 digits referencing the model year). I had asked Tom and he didn't think there were any differences, but when I asked him, I didn't specify auto vs manual. On toyotapartsdeal, there are several different harness part numbers for the xD automatic trans:
2008 - 2009 (P#82121-52F00)
2010 - 2012 (P#82121-52K00)
2013 - 2014 (P#82121-52K01) - Maybe all these parts are the same but just different naming due to the production year. (Recall that I said I overthink things 😆)

I don't want to pay ~$600.00 for a harness, so just trying to find a used one but all eBay listings use the 648.SC1xx format.

There is a harness and engine from a 2012 xD that I'm looking at and it is automatic. It is immobilizer so I can't use the ecu, but can I use the harness?

Right now, this is turning out to be the hardest part of parts procurement. I think once I get past this, it will smooth sailing, parts-wise. Should just need an ECU, throttlebody (and mounting hardware, gasket), alternator and A/C compressor. Planning to use my Yaris (cold climate) starter.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 26, 2018#6
Just scored my ECU (part#89661-52F71). Hopefully the static from buddy's carpet wont mess it up. Prices on eBay ranged from $17.59 (the one I bought) up to $100.00 +. They all looked in similar shape and all were 2008 - 2009, so I saw no point in paying more. This guy's warranty is 6 months, longer than most. And, it has a full bracket - not sure if that fits in the Yaris though.

Picture not included in this copy
tmontagueCaledonia Ont. · Sep 27, 2018#7
Yup bracket is the exact same as the yaris ecu.

Iirc the auto trans harness would have different connectors than its m/t counterpart
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 27, 2018#8
Originally Posted by tmontague ↑
Yup bracket is the exact same as the yaris ecu.

Iirc the auto trans harness would have different connectors than its m/t counterpart
Great! Thanks Trevor. I've made an offer on the 2012 scion engine. Just waiting to hear back from him. The guy confirms that the harness is from the same car; an auto, has A/C (which I now believe was standard equipment on all xDs) but was immobilizer equipped. I'll continue researching if the harness he has will work. I suspect that it will but would rather be 100% sure. Right now my plan is to use our school shop on a weekend (Friday from 4:00pm through Sunday evening) and I'd really like to have it out of there by late Sunday and over to the local shop that's going to do my exhaust. The local shop owner is willing to come over and help out if I get into a bind. He would, of course, charge me for his time. He's worked on my cars in the past and I trust him.
CrankyOldManWest Michigan · Sep 27, 2018#9
One of us! One of us! One of us!

Welcome to the cult--er, club! Looking forward to your build.
tmontagueCaledonia Ont. · Sep 27, 2018#10
An immobilizer harness should work no problem but the best bet is to pull the immobilizer pins front the connector that goes into the ecu just in case so this way the ecu has no chance that any signal for an immobilizer could be read
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 27, 2018#11
Originally Posted by CrankyOldMan ↑
One of us! One of us! One of us!

Welcome to the cult--er, club! Looking forward to your build.
Haha! Thanks Sam. Not in yet...not at least until I'm driving up and down the road in a 2ZR-FE-powered Yaris. But, I really do wanna join. 😁
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 27, 2018#12
Originally Posted by tmontague ↑
An immobilizer harness should work no problem but the best bet is to pull the immobilizer pins front the connector that goes into the ecu just in case so this way the ecu has no chance that any signal for an immobilizer could be read
Ah, sounds like excellent advice. Whenever I get my harness and associated wiring diagram, I will endeavour to find those spots and see if there are any pins occupying them. If so, I will remove them. Thank you. I'd really still like to find out the differences - if any - between the auto engine harnesses.
atomic_hojiKincardine, ON, Canada · Sep 27, 2018#13
Originally Posted by CrankyOldMan ↑
One of us! One of us! One of us!

Welcome to the cult--er, club! Looking forward to your build.
LOL +1

Originally Posted by 06YarisRS ↑
Thanks gentlemen! To pick up on a few points... Adam, thanks for the advice on the wiring diagrams. I will try to find those. You mention body harness? I thought that all I was concerned with was the engine harness. ...

From my research, the xD came in both auto and manual transmission. ...

I don't want to pay ~$600.00 for a harness, so just trying to find a used one but all eBay listings use the 648.SC1xx format.

There is a harness and engine from a 2012 xD that I'm looking at and it is automatic. It is immobilizer so I can't use the ecu, but can I use the harness?

...
Yes.. Two harnesses plug into the ECM - one for the engine, which is basically a pile of wiring that 'drapes' over the engine and routes to all the sensors, etc.. and the bundle goes to a long, rectangular connector at the ECM. Then there's the body harness, which is how the ECM talks to the rest of the car, that routes around the engine bay and into the interior through a grommet up by the brake cylinder; this one has a smaller, square/rectangular connector at the ECM. You need the engine one to match your 2ZR (preferably with the engine and intact) and keep the body harness on your Yaris. <-- not being pedantic, just clear how I use the wording between the two... lol

Definitely try to get the engine harness associated with the engine, even if it needs a couple of connectors swapped those are $12-$20 or so each - just remember to sort it out and order once! The $22 shipping on a $16 connector hurts when you do it twice. lol 🙄 A bit of bravery for soldering or crimping may be required, but given you repainted your Yaris, I suspect you're up for the task. 👍

I just double checked, but on my 3rd gen., and I imagine the 2nd gen. as the key and chip ECU are inside the car, the immobilizer wiring is on the body harness, not the engine harness. So, even if that 2ZR from the xD was immobilizer equipped the engine harness won't have any of the immobilizer wiring... You are likely plug and play to an xD ECM (*ECM that matches MT/autobox) Where I ran into trouble is the connectors that interfaced from the engine harness to the junction box (J/B) - i.e. power and grounds, etc.. to the main J/B. That's where I ordered the Toyota connector and re-pinned to match the accepting connector in the main J/B on the Yaris.

If that ECM you scored is an autobox and non-immobilizer I think you're headed down the right path!

When you get the wiring diagrams, etc.. keep us posted, I'm sure everyone will be happy to clarify / peer check things for you. 👍

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 27, 2018#14
Originally Posted by atomic_hoji ↑
LOL +1



Yes.. Two harnesses plug into the ECM - one for the engine, which is basically a pile of wiring that 'drapes' over the engine and routes to all the sensors, etc.. and the bundle goes to a long, rectangular connector at the ECM. Then there's the body harness, which is how the ECM talks to the rest of the car, that routes around the engine bay and into the interior through a grommet up by the brake cylinder; this one has a smaller, square/rectangular connector at the ECM. You need the engine one to match your 2ZR (preferably with the engine and intact) and keep the body harness on your Yaris. <-- not being pedantic, just clear how I use the wording between the two... lol

Definitely try to get the engine harness associated with the engine, even if it needs a couple of connectors swapped those are $12-$20 or so each - just remember to sort it out and order once! The $22 shipping on a $16 connector hurts when you do it twice. lol 🙄 A bit of bravery for soldering or crimping may be required, but given you repainted your Yaris, I suspect you're up for the task. 👍

I just double checked, but on my 3rd gen., and I imagine the 2nd gen. as the key and chip ECU are inside the car, the immobilizer wiring is on the body harness, not the engine harness. So, even if that 2ZR from the xD was immobilizer equipped the engine harness won't have any of the immobilizer wiring... You are likely plug and play to an xD ECM (*ECM that matches MT/autobox) Where I ran into trouble is the connectors that interfaced from the engine harness to the junction box (J/B) - i.e. power and grounds, etc.. to the main J/B. That's where I ordered the Toyota connector and re-pinned to match the accepting connector in the main J/B on the Yaris.

If that ECM you scored is an autobox and non-immobilizer I think you're headed down the right path!

When you get the wiring diagrams, etc.. keep us posted, I'm sure everyone will be happy to clarify / peer check things for you. 👍

-- Adam
Thanks Adam. A tiny setback...the seller listing the Scion xD engine informs me that he sold the harness that goes with that 2012 engine. Now I have to decide if I want that xD engine or the 2011 Corolla engine (which has the throttlebody but would need the timing cover bracket). Either way, this puts me in a position of having to decide which xD harness to buy. There are a couple available that are from automatics. I think I just need to buy one from an automatic and move forward. If I'm understanding you correctly, the immobilizer should not be an issue as its wiring in the BCM harness. Fact is, the number of available used harnesses is really limited and I've already seen a couple get sold.

I've just been over to TIS and watched parts of the tutorial. I guessing the EWD section in the library would contain what I'm looking for. This is new to me as the only wiring diagrams I've ever used were for such things as stereo installs. Would I be looking for pinout diagrams of the ECU. And, I assume there would be pinout diagrams for each plug on the harness?

And, yes, the ECU I bought from an 08 xD is for auto and non-immobilizer.
tmontagueCaledonia Ont. · Sep 27, 2018#15
Yes what Adam said is correct. Stop waiting and grab an a/t xd harness before they're all gone and you are stuck paying toyota prices for one! Keep your 1nz harness as many of the connectors are interchangeable and its helpful to have extra just in case
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 27, 2018#16
Originally Posted by tmontague ↑
Yes what Adam said is correct. Stop waiting and grab an a/t xd harness before they're all gone and you are stuck paying toyota prices for one! Keep your 1nz harness as many of the connectors are interchangeable and its helpful to have extra just in case
Done...I will order one tonight. Thank you!

Seller accepted my offer. Picked up a 2011 Auto xD harness (Part#82121-52K00).

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 27, 2018#17
Bought Engine $700.00

Hope it makes it from Ohio in one piece.

2011 Toyota Corolla with 42000 miles. Rear collision, no front end damage.

Has intake manifold, exhaust manifold, throttlebody, flywheel, coils and even a harness, Anyone looking for a Corolla engine harness? 😁

EDIT: Got the call today (28 Sept) from the seller confirming delivery address. Found out that they use their own shipper so I feel better about that. They said that if there is any damage it will be paid for.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 27, 2018#18
Other Hardware.

Timing cover mount, 3 bolts and a nut

Picture not included in this copy
atomic_hojiKincardine, ON, Canada · Sep 28, 2018#19
🎉 Looks awesome! I don't think you're "planning a swap" anymore - you're neck deep.. 😁

Originally Posted by 06YarisRS
...
I've just been over to TIS and watched parts of the tutorial. I guessing the EWD section in the library would contain what I'm looking for. This is new to me as the only wiring diagrams I've ever used were for such things as stereo installs. Would I be looking for pinout diagrams of the ECU. And, I assume there would be pinout diagrams for each plug on the harness?
Yes, all the EWDs you can grab! (And repair manual sections if you have time, esp. related to the 2ZR in the xD manual). The System Circuit diagrams are the best, but the Location ones are handy too, and the Overall ones are more technical when you need to dive in. ECM is included in ECS (Electronic Control System) in my 2018 Yaris, but the iM was under Cruise Control, so root around..

-- Adam
tmontagueCaledonia Ont. · Sep 28, 2018#20
Right on, engine looks to he in good shape.

Do yourself a favor when the engine is still out of the engine bay and easily accessible - remove as many bolts as you can and cover them in anti seize. Specifically the exhaust manifold bolts, intake manifold, fuel rail etc.

Also remove any hoses and spray silicone lube on the metal fitting/inside the end of the hose and re install. You have no idea how much easier this will make your job down the road if you ever have to remove anything.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 28, 2018#21
Originally Posted by atomic_hoji ↑
🎉 Looks awesome! I don't think you're "planning a swap" anymore - you're neck deep.. 😁



Yes, all the EWDs you can grab! (And repair manual sections if you have time, esp. related to the 2ZR in the xD manual). The System Circuit diagrams are the best, but the Location ones are handy too, and the Overall ones are more technical when you need to dive in. ECM is included in ECS (Electronic Control System) in my 2018 Yaris, but the iM was under Cruise Control, so root around..

-- Adam
Haha, I guess so... 'In for a dime, in for many dollars', If I can do this, exhaust included for under $2500 CAD, I'll be ecstatic.

I'll be honest. The thought of the diagrams frightens me LOL. But, I will get a short-term membership. I may come 'knocking on your door" for advice on the specific ones to get if I get into the system and become overwhelmed. 🤤

Thanks Adam.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 28, 2018#22
Originally Posted by tmontague ↑
Right on, engine looks to he in good shape.

Do yourself a favor when the engine is still out of the engine bay and easily accessible - remove as many bolts as you can and cover them in anti seize. Specifically the exhaust manifold bolts, intake manifold, fuel rail etc.

Also remove any hoses and spray silicone lube on the metal fitting/inside the end of the hose and re install. You have no idea how much easier this will make your job down the road if you ever have to remove anything.
Yeah, it looks good from the outside. They said they "tested it and it ran good". That's a similar response to what I got from all the sellers I messaged.

Yes, I think I'll really enjoy playing with the engine before installation. My timing cover bracket is "on order" from the online Toyota Parts dealer, so I'll have a bit more time to do what you suggest regarding anti-seize/silicone. I also ordered a PCV valve (See...I'm listening! 👏). Thought I'd install that before the engine is put in. I should be ok, right, not installing a catch can setup like you did? I won't driving the snot out of it.

I think you mentioned that you installed a Scion upper rad hose or filler neck, did you not? I really want an OEM look and will be searching for an engine cover. So far the ones I've seen online would require me to remortgage my house to acquire. Sometimes local pricing can surprise - in a good way. I'll keep looking around here. Q: If I keep the Yaris filler neck and rad hose, I wonder if the engine cover would fit? May have to just find out after.

Finally, and my apologies for the long-winded response... Your pics from your thread are gone, Photobucket, I presume. Wondering if you'd be amenable to zipping those up (if you still have them , of course) and firing them off to me in an email. I'll totally understand if you don't want to take the time as you guys are already being amazingly helpful 🙇 and I don't want to 'overstay my welcome'. I'd of course keep in mind that your swap was with manual, but pics might be helpful.

Thanks Trevor.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 28, 2018#23
Originally Posted by ern-diz ↑
Subscribed!
Excellent! Glad you're coming along for the show. It could be amusing. LOL!
tmontagueCaledonia Ont. · Sep 28, 2018#24
Originally Posted by 06YarisRS ↑
Yeah, it looks good from the outside. They said they "tested it and it ran good". That's a similar response to what I got from all the sellers I messaged.

Yes, I think I'll really enjoy playing with the engine before installation. My timing cover bracket is "on order" from the online Toyota Parts dealer, so I'll have a bit more time to do what you suggest regarding anti-seize/silicone. I also ordered a PCV valve (See...I'm listening! 👏). Thought I'd install that before the engine is put in. I should be ok, right, not installing a catch can setup like you did? I won't driving the snot out of it.

I think you mentioned that you installed a Scion upper rad hose or filler neck, did you not? I really want an OEM look and will be searching for an engine cover. So far the ones I've seen online would require me to remortgage my house to acquire. Sometimes local pricing can surprise - in a good way. I'll keep looking around here. Q: If I keep the Yaris filler neck and rad hose, I wonder if the engine cover would fit? May have to just find out after.

Finally, and my apologies for the long-winded response... Your pics from your thread are gone, Photobucket, I presume. Wondering if you'd be amenable to zipping those up (if you still have them , of course) and firing them off to me in an email. I'll totally understand if you don't want to take the time as you guys are already being amazingly helpful 🙇 and I don't want to 'overstay my welcome'. I'd of course keep in mind that your swap was with manual, but pics might be helpful.

Thanks Trevor.
Most engine recyclers claim that about their engine - mine had data for oil pressure, pul loss and compression but somehow when I went to pick it up they had to go find it and it was still sitting under the car it was pulled from. BS they never engine dyno'd it, they likely made up the numbers based off the mileage. Either way the 2zr is a very robust motor so typically they are all fine unless oil was rarely changed or it was run dry.

You will be fine without a catch can, just run a good oil and change it frequently. Also avoid only doing short trips in the winter, my catch can picks up a lot of water in the winter months.

Yes, I run the xD upper hose and filler spout which I highly recommend. It mounts nice and solid to the already existing 2 holes on your fan shroud. It also places it at a high point which makes bleeding the coolant easy. Iirc I bought mine from village scion online in the states and it wasn't too much, I think around $40 usd for it all. Btw there are technically 2 hoses as one is just a short 2 inch straight run that connects the fill spout to the radiator. The other is long and runs from the spout to the engine. You realistically could forgo the short one and just cut a piece of existing 1nz hose and make it work. It only cost a few bucks and I didn't want to leave anything to chance so I bought it as well.

I actually was using FB to host my pics but apparently they seem to sweep the url's clean every few weeks as all my pics seem to be been broken links now and this happens every few weeks. I can post the pics back when I get a chance but I will be busy the next couple weeks.

Email me any pics you specifically need and I can send them to you. I have pics of the maf power wire I spliced in which will help you
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 28, 2018#25
Originally Posted by tmontague ↑
Most engine recyclers claim that about their engine - mine had data for oil pressure, pul loss and compression but somehow when I went to pick it up they had to go find it and it was still sitting under the car it was pulled from. BS they never engine dyno'd it, they likely made up the numbers based off the mileage. Either way the 2zr is a very robust motor so typically they are all fine unless oil was rarely changed or it was run dry.

You will be fine without a catch can, just run a good oil and change it frequently. Also avoid only doing short trips in the winter, my catch can picks up a lot of water in the winter months.

Yes, I run the xD upper hose and filler spout which I highly recommend. It mounts nice and solid to the already existing 2 holes on your fan shroud. It also places it at a high point which makes bleeding the coolant easy. Iirc I bought mine from village scion online in the states and it wasn't too much, I think around $40 usd for it all. Btw there are technically 2 hoses as one is just a short 2 inch straight run that connects the fill spout to the radiator. The other is long and runs from the spout to the engine. You realistically could forgo the short one and just cut a piece of existing 1nz hose and make it work. It only cost a few bucks and I didn't want to leave anything to chance so I bought it as well.

I actually was using FB to host my pics but apparently they seem to sweep the url's clean every few weeks as all my pics seem to be been broken links now and this happens every few weeks. I can post the pics back when I get a chance but I will be busy the next couple weeks.

Email me any pics you specifically need and I can send them to you. I have pics of the maf power wire I spliced in which will help you
Awesome. Thanks Trevor. I think I'll start with the stock Yaris rad hose. My wife did some online banking today and her eyes buldged a bit when she saw the credit card statement pending charges. She was aware of the upcoming costs. But, I kinda went on a spending spree the last couple of nights. 😁 Fortunately the big ticket items have by now been procured.

OK, I will let you know which pics will be helpful. I'd definitely take the MAF wiring anytime. But, like you say, you're definitely going to be busy for the next while. Haha. Hope yours sleep better through the night than ours did!
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 29, 2018#26
Originally Posted by tmontague ↑
Yes, I run the xD upper hose and filler spout which I highly recommend.
Since you recommended it...

Just need the actual hose now.

I also compiled - hopefully - all the parts I need to mount the alternator.

Picture not included in this copy
atomic_hojiKincardine, ON, Canada · Sep 29, 2018#27
Originally Posted by tmontague ↑
...
Do yourself a favor when the engine is still out of the engine bay and easily accessible - remove as many bolts as you can and cover them in anti seize. Specifically the exhaust manifold bolts, intake manifold, fuel rail etc.

Also remove any hoses and spray silicone lube on the metal fitting/inside the end of the hose and re install. You have no idea how much easier this will make your job down the road if you ever have to remove anything.
+1 - wish I'd taken the time to do that.. I know it'll make life easier in the long run. Similarly, if you need to run any wiring, etc.. do it (or at least rough it in) while the engine is out of the engine bay - WAY more difficult after-the-fact. lol

Originally Posted by 06YarisRS ↑
Haha, I guess so... 'In for a dime, in for many dollars', If I can do this, exhaust included for under $2500 CAD, I'll be ecstatic.

I'll be honest. The thought of the diagrams frightens me LOL. But, I will get a short-term membership. I may come 'knocking on your door" for advice on the specific ones to get if I get into the system and become overwhelmed. 🤤
If you come in at $2500 CAD you're doing awesome - because of mistakes, additional ECUs for fan control, fuel control, etc.. I was in way deeper than that.

Once you get the hang of the System Circuit diagrams they're actually pretty straight forward - Toyota does a pretty good job of laying them out and labelling, etc.. And YW folks are always here to help! 👍

Like Trevor I also run the upper xD hose and filler neck - the Yaris setup ended up interfering and in the way. I also ran both xD heather hoses as I found mine were kinking to run from the 2ZR to the Yaris firewall - not sure if Trevor, Sam, or Tom found that they needed those or not.

I need to get one of those fan belt adjusters - my home brew made from flatbar is doing to the job, but I suspect is slipping a bit... lol

Can't wait to see the accumulated pile of parts ready to go!

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 29, 2018#28
Originally Posted by atomic_hoji ↑
+1 - wish I'd taken the time to do that.. I know it'll make life easier in the long run. Similarly, if you need to run any wiring, etc.. do it (or at least rough it in) while the engine is out of the engine bay - WAY more difficult after-the-fact. lol



If you come in at $2500 CAD you're doing awesome - because of mistakes, additional ECUs for fan control, fuel control, etc.. I was in way deeper than that.

Once you get the hang of the System Circuit diagrams they're actually pretty straight forward - Toyota does a pretty good job of laying them out and labelling, etc.. And YW folks are always here to help! 👍

Like Trevor I also run the upper xD hose and filler neck - the Yaris setup ended up interfering and in the way. I also ran both xD heather hoses as I found mine were kinking to run from the 2ZR to the Yaris firewall - not sure if Trevor, Sam, or Tom found that they needed those or not.

I need to get one of those fan belt adjusters - my home brew made from flatbar is doing to the job, but I suspect is slipping a bit... lol

Can't wait to see the accumulated pile of parts ready to go!

-- Adam
Haha, $2500.00 is likely conservative. It really becomes apparent how many little bits and pieces you need when doing a swap as opposed to just replacing a part in the same car. I keep looking at the pics of my engine close up, then comparing them to online parts diagrams and/or engine bay pictures online and on youtube for example. I have no idea if some of the hardware (alternator bolts, bracket bolts, small hoses/tubing etc) from the Yaris is transferable. The last thing I want is to stall the whole project (aka, getting running) due to missing some tiny little part. One thing that does freak me out a bit is the number of nipples, little tubes and such coming out of the engine. I hope I will have all the hoses, tubing etc to complete the install.


I did opt for the xD rad hose/filler combo as suggested by Trevor. I'll also check in with Trevor on how it went with his heater hoses 'adaptation'. That reminds me...I'm wondering if the rad hose diameters are similar enough to use my old spring clamps.

I plan to get on to TIS or identifix this evening and have a look for the diagrams. Then, let the downloading begin. 👏

Thanks!!!
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 29, 2018#29
Here is a list of rad hose related parts for the xD. Not sure which I'd need but hopefully not all. I suspect that many are already in the Yaris or are not used. If anyone was willing to say you just need A, B. C etc that would be great. I am already getting the upper rad hose (16571-37090), Filler Sub-Assy Water (16502-37010) and Hose 3 (16573-37030). I'm hoping that's all I need.

Picture not included in this copy

I am getting a membership to identifix or TIS and will be learning about the various wiring for the Yaris, Corolla and xD. This will be time-consuming for me as it's new to me so I'm all ears for tips as per rad hoses etc in the interest of saving time.
ArmstrongRacingSan Diego · Sep 29, 2018#30
This is Awesome!
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 29, 2018#31
Originally Posted by ArmstrongRacing ↑
This is Awesome!
🙇
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 29, 2018#32
Extra parts:

Picture not included in this copy
tmontagueCaledonia Ont. · Sep 29, 2018#33
I still don't know what purpose that engine mount stay does? I have it on my engine but I can't see it doing much for support
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 29, 2018#34
Originally Posted by tmontague ↑
I still don't know what purpose that engine mount stay does? I have it on my engine but I can't see it doing much for support
Yeah, I wondered that too. Maybe to control lateral movement? 🤷

Oh, BTW, Trevor, I think you said that you used your Yaris heater hoses. Is that correct and did you have any issue with reusing them? New ones aren't prohibitively expensive, but if I can save a buck or two here and there, I will. Thanks.
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 30, 2018#35
Quick question before I dive into the wiring diagrams...

Can I use the Corolla timing cover bracket mount bolts to attach the xD bracket? Not sure if there is a difference in bracket thickness and if the bolts are long enough or too long?
ArmstrongRacingSan Diego · Sep 30, 2018#36
They are the same bolts, I reused the corolla bracket bolts on my xD bracket.

Originally Posted by tmontague ↑
I still don't know what purpose that engine mount stay does? I have it on my engine but I can't see it doing much for support
I agree. I never installed that part
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 30, 2018#37
Originally Posted by ArmstrongRacing ↑
They are the same bolts, I reused the corolla bracket bolts on my xD bracket.
Awesome! Thanks!
06YarisRSThread starterFredericton, New Brunswick, Canada · Sep 30, 2018#38
Wow, what a steep learning curve, being relatively new to wiring diagrams.

I figured I'd give myself a little project to help me learn the system and how to interpret wiring diagrams in general. I want to see if my cruise control - currently installed in my Yaris - will work after the engine swap.

Here are 2 snippets from the larger cruise control system circuits that (I think) compares the wiring of the xD and Yaris from the ECU to cruise control stock.

Please look at the pic and tell me if I'm interpreting this correctly. Although the connectors in each vehicle have different names, they are the same shape and the pins are in the same place. I'm pretty sure that this is only one factor in the whole cruise control system that would have to be examined.

Picture not included in this copy


Also, I'm waiting to hear back from the seller of the engine for the VIN number. Gots to find out if the engine came out of a TMC made Corolla or TMMK made. Not sure if this would apply to the engine or just the other parts of the car. Either way, it's slowing me down from downloading all the diagrams I need for the Corolla.
ArmstrongRacingSan Diego · Sep 30, 2018#39
Yes all of the pins “mostly” match up for all of the features. There may be a wire change needed for the auto trans torque converter solenoid, but that my only apply to corolla harnesses. Take a look at Brushforhire’s thread.

And of course, the MAF sensor power wire and swap over the speed sensor wires
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 1, 2018#40
Originally Posted by ArmstrongRacing ↑
Yes all of the pins “mostly” match up for all of the features. There may be a wire change needed for the auto trans torque converter solenoid, but that my only apply to corolla harnesses. Take a look at Brushforhire’s thread.

And of course, the MAF sensor power wire and swap over the speed sensor wires
Thank you! I will check out brushforhire's thread again.

Here is one minor difference I've found in the cruise control systems between the Yaris and xD. Don't know if this will make the cruise control non-functional.

Picture not included in this copy

I've downloaded a lot of diagrams and will use them to plan the speed sensor wire swaps although it has been documented here on YW (looking at the diagrams is helping me to understand how everything is interrelated) . I'll also check out the TC circuits for each car. I know that an alternate source of power was used for the MAF sensor (the reason for the mini add a circuit).

Thanks again!
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 1, 2018#41
Alternator and A/C compressor. UPDATE: This A/C compressor does not fit. See post#135 for different part.

Looks like another trip to the online hardware store! Not sure if the Yaris A/C compressor bolts will work. 🤷

EDIT: Looks like the bolts are the same! Yay! Part#9011908B42

Picture not included in this copy
tmontagueCaledonia Ont. · Oct 1, 2018#42
Careful with the compressor bolts, if they are the same part number then they obviously are compatible.

However, I had a fully pressurized a/c line blow off the compressor and the refrigerant blew out 1 inch in front of my face because the bolt was too short and hadn't actually threaded into the compressor properly and let go.

Triple check your bolts before re pressuring I almost learned a hard lesson that day but got lucky. It will freeze your cornea very fast
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 1, 2018#43
Originally Posted by tmontague ↑
Careful with the compressor bolts, if they are the same part number then they obviously are compatible.

However, I had a fully pressurized a/c line blow off the compressor and the refrigerant blew out 1 inch in front of my face because the bolt was too short and hadn't actually threaded into the compressor properly and let go.

Triple check your bolts before re pressuring I almost learned a hard lesson that day but got lucky. It will freeze your cornea very fast
Thanks Trevor. I remember you mentioned that. Scary! The bolts I was referring to are to mount the compressor. I have yet to match the part numbers between the two cars for the bolts that hold the lines to the compressor. I found a diagram with the bolts for one car, but not the other. Did you ultimately use the Yaris bolts to attach the a/c lines to the compressor? Or did you get new ones?

So, I went to an exhaust shop today and the techs were really interested in the idea of the swap. Nice guys. They had ideas that were cool and affordable but they had to pass it off the manager who did the quote. I was just trying to get a sense of cost and they gave me a price of $300.00 just to connect my stock exhaust to the Corolla manifold! Other shops I called won't do the job unless they bolt on their own aftermarket parts. I have decided to buy a whole new exhaust system for the car. Mine is pretty patchy and kind of noisy as it is. It was due for some exhaust work, and my wife has agreed that it is a repair outside of the swap budget. 😁 Well, at least part of the cost anyway.

My options are (shipping included):

1) Rock Auto: $586.00 CAD for xD Walker midpipe (cats, resonator) and new xD Walker muffler. All stainless steel limited lifetime warranty.

2) Rock Auto: $549.00 CAD EASTERN CATALYTIC 40826 SS midpipe and Walker xD muffler

3)$647.00 CAD for Magnaflow (cats, resonator) Inlet 2.25", outlet 2.25" midpipe and new Walker xD muffler (providing it mates with the Magnaflow midpipe).

4) $485.00 CAD (contingent on an accepted offer) used 2008 OEM xD midpipe (eBay) and new Walker xD muffler. I'm a little sceptical about buying a 10 yr old CAT.

The nice thing about the 4 options above is no labour charge for install. I'll need the donuts and new spring bolt kits of course too. All my rubber isolators are in great shape and I assume they are transferable.

The Magnaflow sounds appealing but not sure if 2.25" is necessary or worth the extra $$. It's doubtful that I'd ever do anything down the road that would require higher flow.

Product links:

Walker xD Muffler
https://www.rockauto.com/en/moreinfo...4562&jsn=14711

Walker Midpipe:
https://www.rockauto.com/en/moreinfo...0321&jsn=10321

Magnaflow Midpipe
https://www.tdotperformance.ca/magna...d-2-25-od.html

Eastern Catalytic Midpipe:
https://www.rockauto.com/en/moreinfo...0322&jsn=10322

eBay xD midpipe:
https://www.ebay.com/itm/Exhaust-Pip...oAAOSwQFZbhDnu

I'm definitely open to opinions as well as other options as long as it stays within a similar range. I haven't seen much else though that isn't significantly more expensive.
atomic_hojiKincardine, ON, Canada · Oct 2, 2018#44
Hmm... I used the Yaris' bolts to attach the AC hoses at the compressor.. felt like they went in snug, but makes me wonder now.. better check before I (finally) get the system pressurized..

RE: exhaust, I made the exact same thought process and ended up with the Walker due to price and availability.. I'm also really unimpressed with it. The stainless is cheap (409?) not the good salt resistant stuff; the bends are poor and reduce the diameter more than it already is, which is a 1.75" like the Yaris - I never found the xD, the Corolla/iM runs a 2", so it's already a restriction; their own gasket numbers didn't fit their exhaust; and fitment was together wasn't great either. Now, fitment to the Yaris I can't really complain about as it's not for the car, but it didn't fit straight into the 3rd gen like I thought it might (exceptinga rear hangar) - you may have better luck with 2nd gen.

I really wanted the Magnaflow, but no dealer online or (semi)local could get the part; backordered indefinitely.. Now going to end up finding a place to put in something that fits better as soon as I can get a day off to get the car in for a quote - assuming I don't run into the problem of places wanting to install bolt in stuff and/or can't actually properly fab exhaust..

Just food for thought.
-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 2, 2018#45
Originally Posted by atomic_hoji ↑
Hmm... I used the Yaris' bolts to attach the AC hoses at the compressor.. felt like they went in snug, but makes me wonder now.. better check before I (finally) get the system pressurized..

RE: exhaust, I made the exact same thought process and ended up with the Walker due to price and availability.. I'm also really unimpressed with it. The stainless is cheap (409?) not the good salt resistant stuff; the bends are poor and reduce the diameter more than it already is, which is a 1.75" like the Yaris - I never found the xD, the Corolla/iM runs a 2", so it's already a restriction; their own gasket numbers didn't fit their exhaust; and fitment was together wasn't great either. Now, fitment to the Yaris I can't really complain about as it's not for the car, but it didn't fit straight into the 3rd gen like I thought it might (exceptinga rear hangar) - you may have better luck with 2nd gen.

I really wanted the Magnaflow, but no dealer online or (semi)local could get the part; backordered indefinitely.. Now going to end up finding a place to put in something that fits better as soon as I can get a day off to get the car in for a quote - assuming I don't run into the problem of places wanting to install bolt in stuff and/or can't actually properly fab exhaust..

Just food for thought.
-- Adam
Thanks Adam!

The A/C compressor came with two bolts, so I'll just take those to the local parts shop and have them match them. I'll post up the bolt size later.

I appreciate your observations on the exhaust. As such, I have made an offer on the used OEM midpipe which indeed looks much smoother and less restrictive. As much as I'd like it, I can't really afford a performance muffler, so I guess it's the Walker for now. Sort of shame as I'm guessing the muffler would be a bottleneck. I just can't see any local shops being able to do anything custom without charging me a fortune.
atomic_hojiKincardine, ON, Canada · Oct 2, 2018#46
No problem! I was just really not impressed (as you can tell..) so I'd hate to see you in the same boat.

Before you buy the muffler section, you might want to try and see if your Yaris' muffler fits the Scion xD main pipe - darned if I can find a picture from when I had the exhausts side-by-side, but if I recall they are basically identical; excepting the chrome tip on the Walker xD muffler. Not sure if my noise comes from the main pipe or the muffler, but I find the xD exhaust very 'brap-y', especially when the revs are up. That's of course a preference vs. function..

Looking forward to seeing this come together!
-- Adam
ArmstrongRacingSan Diego · Oct 2, 2018#47
I guess I got lucky, I found a complete 09 corolla midpipe in a junkyard and just unbolted it, got a spare O2 sensor with it for $250.

But then it was $100 to get it matched to my existing Yaris exhaust
tmontagueCaledonia Ont. · Oct 2, 2018#48
In my experience with a few different exhaust set ups on the 1nz I learned the following:

Below info is on a 2.25" exhaust with the primary cat removed but still running the secondary cat.
Removing the resonator (which is not restrictive at all so has little benefit performance wise) leads to that annoying 4 banger buzzing at anything above 2500rpm. But it did has some nice backfires and burbles. This was with a generic turbo muffler. It also had bad drone on the highway

Adding the resonator back and still keeping the muffler was a great set up as a daily driver. No drone, no annoying buzzing and a slightly aggressive noise but nothing very loud until WOT. I'd recommend this set up as a daily driver and to avoide issues with other people/police. This set up also has little to no burbles or pops - its a very clean sound

Removing the muffler but keeping the one cat and resonator is pretty loud but if you keep it below 2500-3000rpm and don't open the throttle too much it is fine and not too loud. When you get above 3k rpm it is pretty loud and WOT is insane - not annoying insane but think track car BWWWAAHHHH insane. However this is one of the more aggressive sounding exhausts on a 4 banger that I have heard. No raspiness or buzzing. It actually sounds similar to a subie, deeper growl. This will give you a decent amount of burbling but not quite as much as removing the resonator. It will drone a bit on the highway but it is tolerable and not nearly as bad as removing the resonator. It can be driven around police and in neighbourhoods without being obnoxious, you just drive slow or like a normal person on a Sunday drive. - this is my current set up due to a weld breaking on my muffler and everytime I get in it and start it up I smile. It is a nice sounding exhaust.

It seems the facotry resonator does quite a bit for noice on these cars and it is not a restrictive set up like some others out there. My recommendation is keep the resonator.

As for the A/C bolts, yes the mounting bolts are the exact same, I re used my 1nz bolts and they worked perfectly fine. I cannot remember what bolts I ended up using for the a/c compressor lines. Either one of the 1nz ones were too short hence the blow out or I had to re thread it. IIRC I ended up finding another longer bolt from my parts bin.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 2, 2018#49
Thanks gents! Well, my offer on the used OEM midpipe was turned down without even a counter offer. It wasn't a bad offer. It's just they're sticking pretty tight to their price, I'd say. I may go back and make another offer.

My current exhaust has primary cat gone, resonator gone and two cats (an old cat welded in to act as a resonator of sorts). I have doubled up sparkplug defoulers to kill the MIL I had.

I had another look at the Easter Catalytic midpipe and it looks about the same as the Walker in terms of crude looking bends and pinches.

The sound of the exhaust is less important to me than having a free enough flowing system. That said, what Trevor mentions in paragraph 3 (the recommendation for daily driver) sounds like what I'm looking for. At this point though I'd like a bolt on setup so I can save a few bucks by doing it myself.

If my current Yaris muffler is no different in flow (diameter) than the Scion muffler (except the tip, which I might add, is nice), then to me it makes sense to keep it as it is still in decent shape, so long as it bolts up. I could get a nice tip for that.

I guess after writing this, I'm leaning toward making another offer on the eBay used OEM pipe. Quick question: Is a 10 year old CAT something to be concerned about? And, given all of the above, which approach would you take?

AFAIK, my engine is due to arrive tomorrow. I'm chomping at the bit to start tinkering with it. I have my bottle of Permatex antiseize, small brush set at the ready. Will pick up some silicone lube tomorrow. My airbox, ECU and harness all arrived in the past two days as well. Time to get ready to pay some serious duty (Well, 15% basically). Hoping to have everything home by the weekend.

I have downloaded over 60 wiring schematics from TIS for the 3 cars involved in this swap. It's like being a kid in a candy store! Probably way more that I need but, hey, why not? I may as well since I paid the membership. It ends at midnight tonight.

In a pm to Adam, we briefly discussed whether or not to bolt all accessories on before putting the engine in the car. I'd be interested in your experiences/suggestions around doing this. I would really like as much attached as possible but I don't want to get into damaging parts due to lack of clearance issues.

Thanks again!
tmontagueCaledonia Ont. · Oct 2, 2018#50
if the previous car wasn't burning oil than a 10 y/o cat should be fine. If not then just use a spark plug defouler to get rid of the P0420 code.


100% install as much as you can before the install of the engine. Clarence going in isn't an issue with the whole front end off the car. Once the 2zr is in the engine bay you will realise how tight it is an something like a water pump replacement will give you goosebumps.

Also add dielectric grease (or silicone grease) to all of the electrical connectors on the engine. Then install the whole harness to the engine before putting the engine in the car. Then all you have to do is connect the main harness to the ecu behind the engine and you're good to go.

Also have the xD ecu installed on the firewall before the engine goes in