Yarisworld Archive

06YarisRS's 2ZR-FE Swap 5-Door Hatchback (Automatic Transmission)

448 posts · 301,527 views · page 2 of 9

Replies continued

06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 3, 2018#51
Originally Posted by tmontague ↑
if the previous car wasn't burning oil than a 10 y/o cat should be fine. If not then just use a spark plug defouler to get rid of the P0420 code.


100% install as much as you can before the install of the engine. Clarence going in isn't an issue with the whole front end off the car. Once the 2zr is in the engine bay you will realise how tight it is an something like a water pump replacement will give you goosebumps.

Also add dielectric grease (or silicone grease) to all of the electrical connectors on the engine. Then install the whole harness to the engine before putting the engine in the car. Then all you have to do is connect the main harness to the ecu behind the engine and you're good to go.

Also have the xD ecu installed on the firewall before the engine goes in
Thanks! Excellent news all around. I was especially happy to hear that the harness goes on before the engine goes in. Also, Adam did mention that a belt change/putting the belt on would be very difficult with the engine in place.

You mentioned using engine hooks once. Do you have any recommendation on hooks that would work well for this install? Our shop has an engine hoist but no leveler. I'll see about getting one of those.

I'm also wondering if replacing the water pump before installing the engine would be a good move. This engine has relatively low mileage so I would hope that there's still lots of life in that.
tmontagueCaledonia Ont. · Oct 3, 2018#52
Afaik we in the 2zr are not known as a weak spot. My engine had 87k km on it and I kept the original pump on the engine. I just checked to make sure there were no weapons hole leaks.

Putting a new belt on before install is also what I did. Like I said, the 2zr in the yaris is a tight fit width wise so anything on the passenger side will be a bear once the engine is in place.

I don't know if my build thread has part numbers or not for the engine hooks but I ordered the 2 hooks specific for the 2zr. I'd highly recommend spending the $25 they cost. The bolt holes are recessed so these hooks have welded on spacers so that nothing gets pinched by the hook/chain. You can probably use bracket holes with strong bolts if you want but this means removing something off the engine so that you can use the bolt hole and this means you then have to install said part back on once the engine is in place.

I used a leveler, not mandatory but it really helps when trying to line up the trans mount when putting the engine back in place
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 3, 2018#53
Originally Posted by tmontague ↑
Afaik we in the 2zr are not known as a weak spot. My engine had 87k km on it and I kept the original pump on the engine. I just checked to make sure there were no weapons hole leaks.

Putting a new belt on before install is also what I did. Like I said, the 2zr in the yaris is a tight fit width wise so anything on the passenger side will be a bear once the engine is in place.

I don't know if my build thread has part numbers or not for the engine hooks but I ordered the 2 hooks specific for the 2zr. I'd highly recommend spending the $25 they cost. The bolt holes are recessed so these hooks have welded on spacers so that nothing gets pinched by the hook/chain. You can probably use bracket holes with strong bolts if you want but this means removing something off the engine so that you can use the bolt hole and this means you then have to install said part back on once the engine is in place.

I used a leveler, not mandatory but it really helps when trying to line up the trans mount when putting the engine back in place
Thanks Trevor. I will search your thread just in case you listed the part # for the engine hook part numbers. I'll keep the original water pump. I'm going to order a belt - likely Bando or the Continental as I've had good luck with both.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 4, 2018#54
Bought the Magnaflow Midpipe. I found a Canadian distributor that was charging $433.00 CAD (10% discount) with free shipping to my door and everywhere else it was $482.00 USD. I lost out on the purchase of the 2008 OEM pipe and there are no more to be found. The other options were the Walker and Eastern Catalytic pipes and neither look that great (bad bends and crushes). And, neither came with the gaskets, so there's a little savings there.

Magnaflow Midpipe:

https://www.tdotperformance.ca/magna...d-2-25-od.html

Picture not included in this copy

Now all I have to do it hope and pray that the Magnaflow will hook up to my current muffler. I will save some money and come up with a better muffler solution at a later date.
tmontagueCaledonia Ont. · Oct 4, 2018#55
Nice! I bet that would sound real nice without a muffler...
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 4, 2018#56
Originally Posted by tmontague ↑
Nice! I bet that would sound real nice without a muffler...
Just got an email a few minues ago:

"Part: Magnaflow 52159 - Direct Fit OEM Grade Catalytic Converter (2.25" ID/2.25" OD)


The product you ordered Is out of stock with the manufacturer with NO eta on when it will be back in production. We apologize for the inconvenience this may cause, give us a call at 1800 276 7566 to source you some alternatives or simply reply to this email with an alternative part number.

Thank you,

TDot Performance Support
"

DANG!!!
WeeYariGeorgetown, Ontario, Canada · Oct 4, 2018#57
Never dealt with TDot but I do have vivid memories of watching them pitch on Dragon's Den a few seasons back.

https://www.cbc.ca/player/play/2679921109

Sent from my Elite_5_5_Octa using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 4, 2018#58
Originally Posted by WeeYari ↑
Never dealt with TDot but I do have vivid memories of watching them pitch on Dragon's Den a few seasons back.

https://www.cbc.ca/player/play/2679921109

Sent from my Elite_5_5_Octa using Tapatalk
Just watched it. Interesting. Their customer service seems good. They took the call quickly, not big wait and were very apologetic. I had a refund notice moments later. They did try to source an alternative part to no avail.

So, I'm done with searching. I just ordered the Eastern Catalytic midpipe and hardware from Rock Auto. I'll bolt that up to my Yaris muffler for the time being.

I'm wondering if the other aftermarket Walker muffler has better flow than the OEM style muffler. If I got the non-oem style, I could at least put a nice tip on it.

Picture not included in this copy

Adam didn't seem to think there was much difference in diameter of the piping between the aftermarket exhaust and the Yaris, so I'll go with that for now. Maybe sometime down the road, I'll look at an axleback performance muffler or plan a custom axleback.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 4, 2018#59
I put the bracket on the cheap mount. This is the result. I don't think I want to bother putting this in the car. Please check out the video. Looks like time to order the actual OEM mount.This may have just been a $60.00 experiment.

Advice appreciated. Thanks!

https://www.youtube.com/watch?v=5milc-eiyF0
tmontagueCaledonia Ont. · Oct 4, 2018#60
Originally Posted by 06YarisRS ↑
Just watched it. Interesting. Their customer service seems good. They took the call quickly, not big wait and were very apologetic. I had a refund notice moments later. They did try to source an alternative part to no avail.

So, I'm done with searching. I just ordered the Eastern Catalytic midpipe and hardware from Rock Auto. I'll bolt that up to my Yaris muffler for the time being.

I'm wondering if the other aftermarket Walker muffler has better flow than the OEM style muffler. If I got the non-oem style, I could at least put a nice tip on it.

Picture not included in this copy

Adam didn't seem to think there was much difference in diameter of the piping between the aftermarket exhaust and the Yaris, so I'll go with that for now. Maybe sometime down the road, I'll look at an axleback performance muffler or plan a custom axleback.
Walker diameter looks larger. Yaris muffler is tiny and is very restrictive- crazy quiet but very restrictive. I'd recommend the Walker set up.

I've had ok experience w/ tdot and they are easy to get a hold of. They are just so large they never seem to have their shit together. Ron told me about Garage16 and every since then I'll be using them from now on for performance parts
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 4, 2018#61
Originally Posted by tmontague ↑
Walker diameter looks larger. Yaris muffler is tiny and is very restrictive- crazy quiet but very restrictive. I'd recommend the Walker set up.

I've had ok experience w/ tdot and they are easy to get a hold of. They are just so large they never seem to have their shit together. Ron told me about Garage16 and every since then I'll be using them from now on for performance parts
I'll check out Garage16 in a bit. Thanks.

I agree, the Walker looks better.

I really like the look these but expect that they would do little to keep the noise at a reasonable level. Nor do I know if I'd have enough room. Have to do some measurements and, of course, would have to weld the hanger in the right place. I'd cut my current muffler off and use the piece from the axle to the new muffler and an adapter to bring it up to size


I wonder if my new midpipe with its 2 cats and resonator and one of the mufflers below would produce a reasonable sound. I know they're probably cheap junk (at under $40.00 USD each) but my car won't be driven in the winter so at least it wouldn't have to contend with salt and sand. I have a little more faith in the cheap import stainless steel products as both of my cheap $3.60 exhaust tips are still perfect. The one on my 08 has been through a winter and is still mint.

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 4, 2018#62
Tonight's Project:

Wire harness inspection. I am learning each connector by using the "Location C", "Engine Control", "Connector List" and "Ignition System" pdfs from Techinfo. The more I dig into this, the less intimidated I am with regard to this swap. That said, I know there is a lot ahead of me. I'll use Trevor's pic of his MAF wiring to plan that modification.

Picture not included in this copy
tmontagueCaledonia Ont. · Oct 4, 2018#63
Good idea. I found that helped a ton with wrapping my head around it all. Having parts come in early and you tinkering with them and setting them up makes it much simpler when it is time to install it

I sort of had no choice as I had 5 days to do the swap and have my car running to get me to class and work so I over prepared out of necessity. But in general it will make things go smoother.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 4, 2018#64
Originally Posted by tmontague ↑
Good idea. I found that helped a ton with wrapping my head around it all. Having parts come in early and you tinkering with them and setting them up makes it much simpler when it is time to install it

I sort of had no choice as I had 5 days to do the swap and have my car running to get me to class and work so I over prepared out of necessity. But in general it will make things go smoother.
For sure. I like to look at the diagrams to see how everything interrelates. My plan for the MAF wiring is set. Got my soldering iron, heat shrink, loom and electrical tape ready. I thought I'd ordered a mini add a fuse, but I haven't yet. Will pick one up tomorrow.

If you had a chance to look at my engine mount youtube vid, I'd appreciate your opinion. You used an OEM one, right? The slightest force moves the bracket up and down. I can only imagine the engine bucking around. I expect that the OEM mount is much more solid. I understand how all mounts triangulate to keep the engine in place, but the movement on this mount seems excessive and it creaks a lot!

Thanks!
tmontagueCaledonia Ont. · Oct 5, 2018#65
Hmm, yes I used a used OEM mount and it definitely doesn't seem to move as much as that one. Worst case scenario you can install it on the car and if the engine moves around too much then swap if for an oem unit. They are easy to replace once the engine is in the car.

Either way that seems like a lot of movement from that mount
CrankyOldManWest Michigan · Oct 5, 2018#66
Wow, 4 pages already!

I second using the OEM engine hooks. I can't remember if the part number is available in the parts diagrams or if it's only in the repair manual.

Good on you for diving in to the EWDs! Once you understand the naming/numbering conventions, it's pretty simple. You can even search the PDFs for connector names to help with cross referencing.

The one thing that I would do differently on mine would be to partially drop the subframe before attempting to install the engine/trans assembly. I was so focused on the trans not clearing the subframe that I ran the load leveler into the base of the windshield. Not a fun repair for a moment's distraction. If you only remove the front bolts and partially remove the rear bolts, it should give you enough room.
tmontagueCaledonia Ont. · Oct 5, 2018#67
That reminds me - I'd highly recommend taking an air hammer or sledge hammer to the "wing" of the subframe that sticks out right near the transmission drain bolt.

It gives you a bit more clearance and make fluid drains less messy in a m/t. It's easier to do with an empty engine bay. It a flat pthin piece if subframe that is easy to bend away
atomic_hojiKincardine, ON, Canada · Oct 5, 2018#69
Glad you've made some good progress! 👍

w.r.t. the Walker muffler - that "U" shape that comes out of the muffler is ~1.5", which is actually tighter than the stock Yaris' pipes; Walker made 0 attempt to mandrel bend anything, so bends are very restrictive - at least the factory, while not perfect, maintains most of the 1.75" diameter.

I actually had the exact same order and response from TDot - the customer service was great, and I've ordered from them again for some other, smaller part that they had a decent price on just because of the customer service. Come across Garage16, but never heard first hand feedback, so good to hear they've been decent. 😁

I second Sam's point about the cross member - I think it'd make life a lot easier for the extra bit of work to drop it. Alternatively, Trevor's point about clearancing it would work - I also got hung up on the damn thing a lot, but at least didn't smoke my windscreen.. 😲

Can't wait to see ya dive into it!
-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 5, 2018#70
Thanks gentlemen!

I will plan to both loosen the subframe as well as bend back the tab as recommended as recommended by Sam and Trevor. I checked out your wiring guide, Tom. Thanks for that. It is very helpful. It's sad, Adam, that an affordable (subjective) exhaust system isn't available. When you say the "U" shape, are you talking about where the muffler does the 90 degree turn and heads to the tailpipe? The other design style 'looks' as though it might be less restrictive. I'm really disappointed that I didn't get the Magnaflow. How long ago did you try to buy yours from tDot? Because, they still have the listing up on their site.


My engine arrived today. I just have to get one of my buddies with half tons to take me across to get it. As much as I was hoping to have it this weekend, it's likely going to be early to mid next week.
tmontagueCaledonia Ont. · Oct 5, 2018#71
fwiw I never found that the subframe was any issue nor did I feel that loosening it would have made any difference. I also had a hoist and engine leveller to help. I found I wheels the engine into the engine bay (super careful of the lack fo space for the width of ther 2zr) and then slowly bolted each of the side engine mounts on but kept them loose. I then got the dogbone mount in and then tightened it all up. Having a jack underneath helps the get the engine in a better position (use a 2x4 under the oil pan.)

I actually did the clearancing with an air hammer after when I went to pull the trans for the lightweight flywheel. It's just that its easier to do with the engine out of the engine bay.

If others state is easier with the subframe loosened then I'd probably do it just in case. Just keep in mind it will require an alignment once it is all back in place which is one of the reasons I didn't bother with it.

Splitting the trans and engine sucks with the 2zr since everything becomes so limited with width. Anything you need to do to the trans do it while it's out of the car.

In my experience w/ Tdot performance is really friendly and shipping is very fast if a place has the part you are looking for (Tdot carries no inventory they are simply an online seller or middleman between stores and the online consumer). However the problems arise when parts are not properly labelled for the proper year of manufacture for a car. It took way too many calls to have them refund me 10% due to their mistake. My wife had to call while I was at work and every time they saids they would do it and kept forgetting. There were also delays on getting my seat bracket once it was made and when I had to order it after they gave me the wrong one the first time I was told it was ordered and then 3 days later was told I need to order it to get it started. Not a terrible experience really but more of a piss off that leaves a bad taste in your mouth when you purchase a part expecting it to be ready in time for track days you have booked. I always try to use a smaller company when the products are a similar price and quality. I have always had better experiences with smaller companies as there is usually less people that things have to go through to get done.
stidnamAustralia · Oct 6, 2018#72
Originally Posted by 06YarisRS ↑
For sure. I like to look at the diagrams to see how everything interrelates. My plan for the MAF wiring is set. Got my soldering iron, heat shrink, loom and electrical tape ready. I thought I'd ordered a mini add a fuse, but I haven't yet. Will pick one up tomorrow.

If you had a chance to look at my engine mount youtube vid, I'd appreciate your opinion. You used an OEM one, right? The slightest force moves the bracket up and down. I can only imagine the engine bucking around. I expect that the OEM mount is much more solid. I understand how all mounts triangulate to keep the engine in place, but the movement on this mount seems excessive and it creaks a lot!

Thanks!
I have a brand new Scion XD engine mount sitting on my desk and I can confirm it does not move to the degree your aftermarket one does. If I really try I can slightly move the bracket attached to the top bolt, but it's pretty stiff.

Personally, I wouldn't use that mount. Send it back as defective and buy OEM.

Part number should be (But please check with your dealer)

12305-37190 - https://www.sparksparts.com/oem-part...unt-1230537190
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 6, 2018#73
Originally Posted by tmontague ↑
fwiw I never found that the subframe was any issue nor did I feel that loosening it would have made any difference. I also had a hoist and engine leveller to help. I found I wheels the engine into the engine bay (super careful of the lack fo space for the width of ther 2zr) and then slowly bolted each of the side engine mounts on but kept them loose. I then got the dogbone mount in and then tightened it all up. Having a jack underneath helps the get the engine in a better position (use a 2x4 under the oil pan.)

I actually did the clearancing with an air hammer after when I went to pull the trans for the lightweight flywheel. It's just that its easier to do with the engine out of the engine bay.

If others state is easier with the subframe loosened then I'd probably do it just in case. Just keep in mind it will require an alignment once it is all back in place which is one of the reasons I didn't bother with it.

Splitting the trans and engine sucks with the 2zr since everything becomes so limited with width. Anything you need to do to the trans do it while it's out of the car.

In my experience w/ Tdot performance is really friendly and shipping is very fast if a place has the part you are looking for (Tdot carries no inventory they are simply an online seller or middleman between stores and the online consumer). However the problems arise when parts are not properly labelled for the proper year of manufacture for a car. It took way too many calls to have them refund me 10% due to their mistake. My wife had to call while I was at work and every time they saids they would do it and kept forgetting. There were also delays on getting my seat bracket once it was made and when I had to order it after they gave me the wrong one the first time I was told it was ordered and then 3 days later was told I need to order it to get it started. Not a terrible experience really but more of a piss off that leaves a bad taste in your mouth when you purchase a part expecting it to be ready in time for track days you have booked. I always try to use a smaller company when the products are a similar price and quality. I have always had better experiences with smaller companies as there is usually less people that things have to go through to get done.
Yeah, I was really disappointed when I didn't get my exhaust. The site still has it advertised and obviously they don't feel the need to take it down as this happened to Adam a while back with the same item. Their system accepts the customers' money, then has to refund it. An avoidable situation.

I am glad that the job can be done without dropping the subframe, but I will see how things go.

I'm still super impressed that you did this in your driveway, and by yourself!
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 6, 2018#74
Originally Posted by stidnam ↑
I have a brand new Scion XD engine mount sitting on my desk and I can confirm it does not move to the degree your aftermarket one does. If I really try I can slightly move the bracket attached to the top bolt, but it's pretty stiff.

Personally, I wouldn't use that mount. Send it back as defective and buy OEM.

Part number should be (But please check with your dealer)

12305-37190 - https://www.sparksparts.com/oem-part...unt-1230537190
Thanks Stidman! I'm really leaning toward just buying an new OEM mount. I'll email the seller, link them to my video and see if they will refund me.

EDIT: I did order an OEM mount. I also emailed the seller of the aftermarket one and requested an RMA.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 6, 2018#75
The engine has landed at home.

My daughter may be the new wrench turner in the family. She really enjoyed helping to put the engine hoist back together. I'll be borrowing an engine stand and leveler from the school early next week. In the meantime, I'll try to source the engine hooks.

Picture not included in this copy

A couple of my former students lending a hand. One is actually our tenant.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 6, 2018#76
MAF Wiring in harness

Started hacking away at the harness. My glasses mysteriously went missing so there was a lot of squinting going on. I added the MAF sensor power wire that will run to the fuse box (thanks Trevor). Not having any automotive wire on hand, I grabbed a roll of decent quality 14 ga stranded copper speaker wire. Not sure if the OEM wiring is aluminum or copper. Hopefully there won't be any dissimilar metals issues. It's a really good connection with about 1" of wire from each wire braided into each other, soldered, heat shrinked and taped. I may have shorted the power wire a bit, but I think the mini add-a-circuit wire will reach. If not, I'll splice in a bit, solder and heat shrink.

Braided and soldered

Picture not included in this copy

Heat shrink, tape and 90 bend

Picture not included in this copy

More taping

Picture not included in this copy

Finished connection

Picture not included in this copy
ArmstrongRacingSan Diego · Oct 6, 2018#77
There used to be some good options for exhaust systems by RPM, but as you all know....they canned their 2zr support.

I would personally recommend finding a oem midpipe or at least the collector, then just have the rest of the system made to meet up with whatever performance muffler you have. I went with 2.25 all the way due to the overwhelming amount of complaints from people that tried 2.5. 1 catalyst and 1 resonator is all you need to pass smog and sound restrictions

You’re engine looks really nice, must be a unit someone took care of. Things should come together quickly now!

I strongly approve of your wiring work, looks completely oem. I soldered my wholle home-made harness with heat sharing also, and with all these years, and having it apart several more times... and racing! Don’t let anyone tell you solder is “brittle”.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 6, 2018#78
Originally Posted by ArmstrongRacing ↑
There used to be some good options for exhaust systems by RPM, but as you all know....they canned their 2zr support.

I would personally recommend finding a oem midpipe or at least the collector, then just have the rest of the system made to meet up with whatever performance muffler you have. I went with 2.25 all the way due to the overwhelming amount of complaints from people that tried 2.5. 1 catalyst and 1 resonator is all you need to pass smog and sound restrictions

You’re engine looks really nice, must be a unit someone took care of. Things should come together quickly now!

I strongly approve of your wiring work, looks completely oem. I soldered my wholle home-made harness with heat sharing also, and with all these years, and having it apart several more times... and racing! Don’t let anyone tell you solder is “brittle”.
Thanks very much, Tom. Believe me, I've tried desperately to get an OEM pipe. I contacted over 20 different places and the only pipe I could find, was from a 2010 and was $450.00 USD plus shipping. I had at least two outfits tell me that they just cut the exhaust systems off to get the engines out. I cringed! A local shop wanted to charge me over $300.00 to just attach the Corolla exhaust manifold to the stock Yaris exhaust - nothing else. Other places didn't even want to touch it unless I bought all new parts from them.

I'm kicking myself in the arse now for not buying the 2008 OEM pipe when I had the chance. I made very solid offers and they kept rejecting them and it was a "Make an Offer" listing. I figured I'd make one final one but by the time I went to, it was gone.

Do you really think that the aftermarket OEM Scion xD midpipe that I ordered will be too restrictive? I would hate to go to all this work and expense and suffer significant power/torque losses due to inadequate flow?

I was so disappointed when the Canadian outfit sold me the Magnaflow and then told me they couldn't get it.

Yes, the engine looks good. I had a heck of a time getting the dipstick out but once it come out it would go back in and out fine. I thought it was going to break off and slide down into the pan. I hope the internals are good as I'd be in a bad way if there were any major problems. I'll clean it up and antiseize various bolts as recommended by Trevor. I still have to make a decision about the location for the swap. The school shop would be awesome but I'd have to be running and gone by Sunday evening. I have a guy who will help me but I have to do it on a weekend he's available.
We are away next weekend, so maybe the following.
ArmstrongRacingSan Diego · Oct 7, 2018#79
I would think any exhaust pipe made for the 1.8 will have properly sized piping. I made the comment about pipe size in case you had to get it made.

Make sure you get the a/c evacuated before the go time. With the auto I don’t think you have to pull the trans out at all, remove the torque converter bolts behind the black cover, put a jack under the trans to hold it in place, then there should be enough room to lift the engine straight up and out.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 7, 2018#80
Originally Posted by ArmstrongRacing ↑
With the auto I don’t think you have to pull the trans out at all, remove the torque converter bolts behind the black cover, put a jack under the trans to hold it in place, then there should be enough room to lift the engine straight up and out.
😲 Wow, this is indeed good news! I figured with what I'd read about the mounts not necessarily lining up 100% that it might be easier moving the whole engine and transmission as a mass to line it up with the mounts. But, if I remember, your mounts did line up, right? Maybe I'm mixing it up with a swap involving a manual trans.

Does this apply to dropping the 2ZR back in after the 1NZ is pulled? So, in theory, I could drop the 2ZR in, bolt up the bell housing, converter bolts and be good - other than the wiring (including the necessary speed sensor wire swaps), ATF lines etc? No need to mess with with axles or suspension components? That could prove to be a major time saver and potential frustration saver! I wonder if the extra width of the 2zr would make it difficult to mate the engine and transmission while in the engine bay. Would I be correct in assuming that if the transmission mounts are either loose or removed, and the transmission supported by a jack, that there would be enough play to tip the trans back and forth to get it bolted to the engine?

It's interesting as when I went to ask the local mechanic if he woud be available in a pinch, he asked why I would remove the trans at all. I dismissed it because I thought he might be thinking about just putting the same type of motor back in - not necessarily one with slightly different dimensions.

Sorry for all the Q's but I'm getting pumped about this!

BTW, my timing case bracket arrived. Just have to hop across the border and get it. So there's something else I can do to my engine while waiting to dive in to the swap.
tmontagueCaledonia Ont. · Oct 7, 2018#81
Awesome progress. In regards to the dipstick tube make sure you cover the dipstick o ring in silicone grease. For what ever reason the 2zr dipstick like to corrode at the top of the tube and seizes it in there. Ask Sam how he knows... even mine after 1 month of not pulling it out got very stuck. Cleaned it up and greased it and no issues since
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 7, 2018#82
Originally Posted by tmontague ↑
Awesome progress. In regards to the dipstick tube make sure you cover the dipstick o ring in silicone grease. For what ever reason the 2zr dipstick like to corrode at the top of the tube and seizes it in there. Ask Sam how he knows... even mine after 1 month of not pulling it out got very stuck. Cleaned it up and greased it and no issues since
Thanks! So, given the frequency with which the typical motorist of today checks his/her oil, it's probably a given that there are 100 000's of 2ZR-based cars driving around with frozen dipsticks. LOL! Will add some silicone grease.

As an aside, and of course it didn't apply in your swap, but would you used some loctite on the torque converter bolts when installing and torquing to spec? I can only imagine the destructive result of having one of those bolts come loose and bouncing around in there.

Completely unrelated...Looks like I'll be getting a new windshield in my '06. Yesterday, the lower passenger corner took a small rock; I think from a oncoming vehicle. The crack is already creeping diagonally toward the center of the windshield. I thought we'd been shot. It was freakin' loud.
tmontagueCaledonia Ont. · Oct 7, 2018#83
I can't say how quickly the tube seizes as my engine bay get exposed to water quicker due to my 2 vents I cut into it. How quickly it happened to mine is probably not the most realistic for others but they are known to seize as Sam also found out.

I did not use loctite on my flywheels bolts in actually used a very small amount of antizeize and torqued them to spec. I don't remember the repair manual saying to use loctite so I never did and haven't had an issue.

I'd only use it if recommended.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 7, 2018#84
Originally Posted by tmontague ↑
I did not use loctite on my flywheels bolts in actually used a very small amount of antizeize and torqued them to spec. I don't remember the repair manual saying to use loctite so I never did and haven't had an issue.

I'd only use it if recommended.
Right, I haven't looked at that part of the repair manual yet. I had just watched a youtube video about how a torque converter is attached and it looked like a thread sealer on the bolts.

I took the Corolla mount off. A 12pt 14mm wrench was adequate, but just. A little tapping was required. Those bolts are in there tight! Definitely a situation for never seize. Had to remove the motor mount guide pin to get the top bolt out of the mount after it was removed from the engine. I would have installed the Scion bracket but I'm waiting to go pick it up when a couple more packages arrive.

Removal:

Picture not included in this copy

Removed:

Picture not included in this copy


New Scion Bracket Installed

Lots of anti-seize!

Picture not included in this copy

xD bracket installed. Just have to go find torque spec in my service manual.

Installed Parts:

A (1 X) Toyota #12315-37040 (bracket)
B (3 X) Bracket mount bolts (came off the Corolla Engine)
C (3 x) Toyota #91552-L1240 (bolts to attach engine mount - to bracket)

Picture not included in this copy
tmontagueCaledonia Ont. · Oct 7, 2018#85
Tom is correct about leaving the trans in the car while swapping the engine. I removed my whole trans w/ the motor because I was replacing the clutch and flywheel.

That said putting the 2zr back into the engine bay and lining up the main shaft to the engine would be a huge pita compared to easily doing it off the car.

Imho I actually think it is quicker to pull them both together, reassemble w/ the 2zr and slide them both back in together. When the front of the car is off there is a ton of room to remove the trans and engine.

Ultimately you will have to decide what works best for you but the 2zr block is a direct bolt on including the starter
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 7, 2018#86
Originally Posted by tmontague ↑
Tom is correct about leaving the trans in the car while swapping the engine. I removed my whole trans w/ the motor because I was replacing the clutch and flywheel.

That said putting the 2zr back into the engine bay and lining up the main shaft to the engine would be a huge pita compared to easily doing it off the car.

Imho I actually think it is quicker to pull them both together, reassemble w/ the 2zr and slide them both back in together. When the front of the car is off there is a ton of room to remove the trans and engine.

Ultimately you will have to decide what works best for you but the 2zr block is a direct bolt on including the starter
Thanks. The main reason I was liking the sound of leaving the trans in the car would be to avoid having to deal at all with the axles and suspension components. I should say that I assume that if left in, the axles and suspension would be untouched. Again, I don't have experience, so I'm just guessing. I do like the idea of having it out to mount the trans, but if I could avoid messing with axles etc, it would be a consideration. Since the rad has to come out with front end removal, then I'd still have to deal with transmission cooler lines etc anyway.

Let's say that I do take both out and put both back in together, will the axles slide into place without having to break the ball joints and pull the struts out?
tmontagueCaledonia Ont. · Oct 7, 2018#87
You don't have to touch the knuckle or suspension to remove the axles. You can get away with it by just removing the ball joint and once its separated from the knuckle you can swing the knuckle out and remove the axle. I do this all the time when working on my axles so that I don't need a realignment every time.

The yaris bj's sit in there snug so a proper tool makes it a breeze to remove them and not damage the bj. I use a tool like this https://www.princessauto.com/en/deta...or/A-p8004135e
ArmstrongRacingSan Diego · Oct 7, 2018#88
Yes the 2zr will drop right in place of the 1nz, just be sure the dowel pins are observed since they can get stuck in the engine or trans. Then if your 2zr has both and one is stuck in the trans it won’t go together. The auto slides in much easier because there is no shaft to align, both components have flat surfaces.

Leave the transmission in and don’t touch any of the mounts, it’s not in the way.
tmontagueCaledonia Ont. · Oct 7, 2018#89
Very true, I forgot that that a/t has no shaft to align
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 7, 2018#90
👏 👏 👏

So...I should still take the front of the car off though? If not, is the radiator removal enough? I'm liking the sound of this more and more all the time!

Thank you guys sooo much! I'm feeling much more confident; not assured, but more confident.

The next thing that I want settled in my mind is the swapping of the speed sensor wires. Looking at wiring diagrams is one thing, but actually envisioning it in my mind with real wires and connectors will get me over this little hump. Any advice or pics would be tremendous. I'll go back and read the threads again but don't recall seeing a pic.
atomic_hojiKincardine, ON, Canada · Oct 7, 2018#91
Great progress man! 👍

That's a nice looking engine, and your wiring is awesome! I would like to say that I've wrapped and completed mine that nicely .... but I can't - still too 'temporary' hah.

You must be getting really excited - or really anxious - or both.. lol

-- Adam
tmontagueCaledonia Ont. · Oct 7, 2018#92
I don't remember much of hand about the speedo wires but I di remember not feeling confident about them. Once I had looked at the 1nz harness when th engine and trans were out and saw what connectors went where it dawned on me.

Iirc I just opened up the harness and removed the wires and connector from the 1nz and moved it to the 2zr. That's the one benefit of removing the engine and trans together is that you can see where everything goes to on the 1nz harness.

And definitely remove the whole front end as well as the hood. I thought about keeping the front end on but with it removed there so much room to slide the engine in instead if having to lift it and drop it into place in a narrow bay.

The front end is super straightforward to remove as you go. You won't need a guide it will all be right there when you start removing things.
atomic_hojiKincardine, ON, Canada · Oct 7, 2018#93
Oh - speaking of removing the front end. If you don't have some already, the plastic interior trim / body panel tools. I picked this set up from Princess Auto, they worked a treat.. https://www.princessauto.com/en/deta...ls/A-p8424624e

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 8, 2018#94
Originally Posted by atomic_hoji ↑
Great progress man! 👍

That's a nice looking engine, and your wiring is awesome! I would like to say that I've wrapped and completed mine that nicely .... but I can't - still too 'temporary' hah.

You must be getting really excited - or really anxious - or both.. lol

-- Adam
Hey Adam. I've been popping in and out of your swap thread, and man, I have to say I thoroughly admire your skill, knowledge and tenacity. I'd probably have given up long ago. My swap sounds like an oil change in comparison. I guess everything is relative (project complexity/mechanical experience). Haha.

And, yes, I am getting both excited and anxious. Unfortunately next weekend is a complete bust: 2 b-Day parties, a wedding out of town and 2 hockey practices. Thank god my wife is good with scheduling/time management!


Best of luck with your project! You will be the first person ever to pull this off, correct? It will be a glorious feeling when you're done, and cause for much celebration. 👍
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 8, 2018#95
Originally Posted by tmontague ↑
I don't remember much of hand about the speedo wires but I di remember not feeling confident about them. Once I had looked at the 1nz harness when th engine and trans were out and saw what connectors went where it dawned on me.

Iirc I just opened up the harness and removed the wires and connector from the 1nz and moved it to the 2zr. That's the one benefit of removing the engine and trans together is that you can see where everything goes to on the 1nz harness.

And definitely remove the whole front end as well as the hood. I thought about keeping the front end on but with it removed there so much room to slide the engine in instead if having to lift it and drop it into place in a narrow bay.

The front end is super straightforward to remove as you go. You won't need a guide it will all be right there when you start removing things.
Thanks very much, Trevor. I will definitely remove the front end. When you scavenged the speed sensor wires from the 1NZ harness, you take the terminals out of the opposite end of the connector (not the CA2 end), run them through the xD split loom, then insert the opposite end terminals into the appropriate place in the corresponding xD CA2 connector as per my pic below? I'm hoping to leave my Yaris harness intact, but maybe this is not feasible. I would probably have to buy terminal ends.

Here is a pic. I know where to put the wires in the xD CA2 connector. Just not sure where the wires in the 1NZ harness connect to on the other end. Do these 3 wires go to different plugs on the xD harness? Sorry for my lack of understanding. 😕

Picture not included in this copy
tmontagueCaledonia Ont. · Oct 8, 2018#96
I honestly don't remember I'll have to go through my build thread and see if I put any info there about it. I just remember having the same question as you but once I saw what the 1nz harness had that the 2zr didn't going to the trans, it became clear what had to be swapped. I never ordered any pins I just removed them from the connectors and moved them if I needed to.

Toyota pins and connectors are very hard to come by. This is why I am keeping my 1nz harness in storage in case I never need a connector.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 8, 2018#97
Originally Posted by tmontague ↑
I honestly don't remember I'll have to go through my build thread and see if I put any info there about it. I just remember having the same question as you but once I saw what the 1nz harness had that the 2zr didn't going to the trans, it became clear what had to be swapped. I never ordered any pins I just removed them from the connectors and moved them if I needed to.

Toyota pins and connectors are very hard to come by. This is why I am keeping my 1nz harness in storage in case I never need a connector.
Thanks Trevor. I'm sure it will make sense when I go to do it. Where the pins go is not an issue. Where they come from is eluding me atm.

EDIT: I am going to review this thread in detail. It looks like it contains the answers I need:

THE 2ZRFE engine swap thread - Just the facts

I picked up the xD bracket that mounts to the timing cover and installed it. Pics are in post #84, page 5. I took your advice, lol, but I may be overdosing the Permatex 😁
WeeYariGeorgetown, Ontario, Canada · Oct 8, 2018#98
Just noticed your pic a while back in which you tout 'lots of anti-sieze'. You sure that's what it is? I'm used to anti-sieze being coppery colour. What you have there looks blue to me which is the colour I associate with locktite.

Sent from my Elite_5_5_Octa using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 8, 2018#99
I started out removing one connector at a time from the Corolla harness and replacing it with the corresponding connector from the xD harness. That worked for about 1/2 of the engine. Then I simply had to remove the rest of the Corolla harness as it was getting too complicated and it was in the way. The plastic retaining clips that hold the harness to the engine did not always line up. So, I'm concerned about securing the harness everywhere it needs to be to avoid rubbing/chaffing etc. I may - in some places, have to use heavy zip ties.

As far as connectors go, I'm making two assumptions. 1) A connector will not plug in unless it is the correct plug. 2) A connector will only plug in if it reaches.

The most confusing parts was the flexplate end of the engine. I'm not sure I got it attached as it's supposed to be. There are a few extra plugs on my harness that I'm not sure where they go. Presumeably they connect to non engine connectors.

If anyone sees anything that looks wrong, please let me know.

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 8, 2018#100
Originally Posted by WeeYari ↑
Just noticed your pic a while back in which you tout 'lots of anti-sieze'. You sure that's what it is? I'm used to anti-sieze being coppery colour. What you have there looks blue to me which is the colour I associate with locktite.

Sent from my Elite_5_5_Octa using Tapatalk
Hey WeeYari. Here is the product I'm using. It's silver. Might just have been the lighting making it look blue.

Picture not included in this copy