Replies continued
WeeYariGeorgetown, Ontario, Canada · Oct 8, 2018#101Cool. I was just picturing you following Trevor's advice to lather every bolt with the stuff and then at some future point uttering 'son of a bitch, that mother is tight!' ;)
Sent from my Elite_5_5_Octa using Tapatalk
tmontagueCaledonia Ont. · Oct 8, 2018#102Hehehe that would be an issue. I used to use silver and that got used to and I received a free large bottle of copper anti seize. Have used tha w/ no issues. As long as its not loctite you are good to go
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 8, 2018#103A Breakthrough!
After straining by brain over this speed sensor issue, I re-read and re-read brushforhire's swap thread. I then went out to my '08 and found that pesky speed sensor way way back and way down on top of the trans. Sure the neighbours were laughing - me out there with my phone light practically falling into the engine bay.
Anyway. I'm pretty sure that I'm going to take the whole wire bit with the connector and incorporate it into the harness, running the wires up to CA2 pins 11, 12 and 13. I think where I was hanging up on this was that I thought that the 3 wires had to go into a connector that was already present in the xD harness. It's more of and add-on wire, per se.
Rather than split the harness open, I may run a small loom alongside, ziptie it and fully tape over it.
Again, let me know if I'm barking up the wrong tree. And Trevor, yes, I'm sure it would have been immediately apparent if I had the Yaris engine out! Haha.
Picture not included in this copy
tmontagueCaledonia Ont. · Oct 8, 2018#104I re read my thread and realised that I never posted about it, it must have been in the thread you had read only.
Iirc I think I ended up pulling the pins and 3 wires I needed and added then to the xd harness. The one end of the wire go to the connector st the trans but the other end simply goes to knead of the small white connectors that attaches to the fuse box. This is what dawned on me when I was comparing both harnesses. I thought it went to the ecu but it simple grabs power/signal from the fuse box so it it a short piece of wire and really quick and easy to add to the xd harness without undoing the whole harness.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 9, 2018#105 Originally Posted by
tmontague ↑ I re read my thread and realised that I never posted about it, it must have been in the thread you had read only.
Iirc I think I ended up pulling the pins and 3 wires I needed and added then to the xd harness. The one end of the wire go to the connector st the trans but the other end simply goes to knead of the small white connectors that attaches to the fuse box. This is what dawned on me when I was comparing both harnesses. I thought it went to the ecu but it simple grabs power/signal from the fuse box so it it a short piece of wire and really quick and easy to add to the xd harness without undoing the whole harness.
Great. Thanks! I already installed my harness, but I think this can be done with it on the engine.
CrankyOldManWest Michigan · Oct 9, 2018#106 Originally Posted by
06YarisRS ↑ Rather than split the harness open, I may run a small loom alongside, ziptie it and fully tape over it.
This is what I did.
What did you end up doing for your MAF power wire?
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 9, 2018#107 Originally Posted by
CrankyOldMan ↑ This is what I did.
What did you end up doing for your MAF power wire?
I split the short section of harness needed and ran a wire from B+ pin 3 in the MAF connector out the end by the fusebox plug (CA2). I picked up a mini add-a-fuse and will do the same as you guys - plug into an ACC location.
Pics are back one page (post #76) if you're interested.
Thanks!
BTW, my midpipe arrived today. Have to call them and see if it's one piece or two. That will determine if I take the van or the car to get it.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 9, 2018#108Great news!
Turns out one of the local auto repair shops (there are only 2 - 3 in our small community) has an exhaust pipe bender and lots of piping. I was told this by one of the guys that works at the parts store. I dropped by and talked to the owner and he said that they hadn't used it in a while but he'd be interested in fabricating an axle back exhaust for me. I showed him pics of my current exhaust and my new muffler and he said he'd like to just remove the flange from my Yaris muffler, form a new pipe over the axle and weld it to my new muffler. He'd weld on the hangers in the right places. When the swap is done, he said to bring the car in and show him where I'd like the muffler positioned. For materials, he told me he'd charge $5.00 per bend and about $5.00 a foot for pipe, plus labour of course. The great thing about this is that I can have him use a larger diameter pipe and my muffler is basically a straight through with a 2.5" inlet. With the aftermarket xD midpipe and a freer flowing axle back, I feel the system should work reasonably well. I had originally asked him to just hack my muffler off and use the axle to muffler part of the stock Yaris pipe and he suggested a new larger diameter piece. I'm stoked!
Here is the inexpensive muffler I bought. I hope it doesn't look too cheesy and isn't too loud. I can always have him put another muffler on if I'm not happy with it.
I think it will look decent with the dual 3" tips just peeking out from under the car. It's not high end stainless steel, but, as I mentioned before, the cheap tips I bought are holding up really well, plus this exhaust will never see winter driving conditions.
Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 11, 2018#109Midpipe and Other Parts
Adam was right. This pipe starts out huge and then tapers down to 1 1/2" after the resonator. It is what it is. Hopefully the flow won't be restricted too much. As much as I hate the thought of it I'm tempted to gut the cats!
I ordered a couple spring bolt kits and a donut as there was nothing stated about including those parts and they did in fact come with it. Not a biggle as these are pretty much consumable items.
My target for the swap is the weekend of 20 October, unless of course, I get the itch to start tearing things apart on the week day evenings.
Picture not included in this copy
Picture not included in this copy
ArmstrongRacingSan Diego · Oct 13, 2018#110Wow that’s a nice looking piece. Let us know how well it fits and sounds at the end.
Make sure you never drive a corolla after the swap, or you will realize just how slow they are haha
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 13, 2018#111 Originally Posted by
ArmstrongRacing ↑ Wow that’s a nice looking piece. Let us know how well it fits and sounds at the end.
Make sure you never drive a corolla after the swap, or you will realize just how slow they are haha
I will definitely post about the final exhaust. Maybe I'll do a quick video.
Haha, I've been wanting to drive a corolla before the swap to see how much faster the 2ZR powered Yaris is. I seem to recall Trevor saying it was like the car lost 700 lbs or something like that.
ArmstrongRacingSan Diego · Oct 15, 2018#112When my Yaris was his in the door and the body shop had it, I had a corolla rental. When I got my Yaris back I was so surprised how much faster it is! I think the swapped Yaris may be just as fast as the tC...
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 15, 2018#113 Originally Posted by
ArmstrongRacing ↑ Wow that’s a nice looking piece. Let us know how well it fits and sounds at the end.
Make sure you never drive a corolla after the swap, or you will realize just how slow they are haha
Originally Posted by
ArmstrongRacing ↑ When my Yaris was his in the door and the body shop had it, I had a corolla rental. When I got my Yaris back I was so surprised how much faster it is! I think the swapped Yaris may be just as fast as the tC...
I like the sound of that - the potential to be as fast as the TC. Just did some research:
First Generation Scion TC: ~160 HP, ~162 Torque, Curb Weight 2970 lbs, Power:Weight 0.054, 0-60 in 6.8 - 7.3 sec.
Swapped Yaris ~130 HP, ~127 Torque, Curb Weight 2340 lbs, Power:Weight 0.056, Scion xD itself claims 0-60 in 7.8 - 7.9 which would be almost 300 pounds heavier than the swapped Yaris. Not sure if these 0-60 times are with manual or auto. I know that gear ratios etc would also come into play.
Not sure how it would translate into real world application, but it sounds like the swapped Yaris - at ~600 lbs less and a marginally higher power to weight ratio - might indeed be comparable to the TC.
Further research shows that the 2nd Generation TC has 180 HP, 173 ft/lbs torque and a 6-speed auto.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 16, 2018#114This thread is getting long but I want to document as many steps as possible. Just picking away until the "big day" of the swap. Alternator installation is very straight forward. I was amazed that I managed to actually order all the parts I needed. A/C compressor will have to wait until the 1Nz is pulled for the bolts.
All fasteners lubricated with anti-seize. Will grease all the sliding parts.
Picture not included in this copy
I think I'm liking the belt tensioner adjuster compared to the Yaris set up.
Picture not included in this copy
WeeYariGeorgetown, Ontario, Canada · Oct 16, 2018#115 Originally Posted by
06YarisRS ↑ I think I'm liking the belt tensioner adjuster compared to the Yaris set up.
HELL YES!!!!!!!
ArmstrongRacingSan Diego · Oct 16, 2018#116Hey your water pump pulley is different from mine, what year is your engine from again?
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 16, 2018#117 Originally Posted by
ArmstrongRacing ↑ Hey your water pump pulley is different from mine, what year is your engine from again?
Heart attack coming on... 😳
The engine is from a 2011 Corolla. Is your pulley larger/smaller? Or, just a different style?
Am I ok?
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 16, 2018#118A great score...
Local auto recycler for $25.00 CAD. Cheapest I could find online was $80.00 USD and in much worse shape. This one is nearly mint! Even came with all 4 rubber grommets unlike many of the online listings. Just have to figure out how to get the part number marker ink off of it.
Picture not included in this copy
A little kid's sunscreen made short work of the marker.
Picture not included in this copy
ArmstrongRacingSan Diego · Oct 17, 2018#119 Originally Posted by
06YarisRS ↑ Heart attack coming on... 😳
The engine is from a 2011 Corolla. Is your pulley larger/smaller? Or, just a different style?
Am I ok?
Mine was labeled as 13’, it’s the same size just the pulley design looks better on yours.....maybe you have the updated pump
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 17, 2018#120 Originally Posted by
WeeYari ↑ HELL YES!!!!!!!
I know. Great, isn't it. No more crow bar. 👏
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 17, 2018#121 Originally Posted by
ArmstrongRacing ↑ Mine was labeled as 13’, it’s the same size just the pulley design looks better on yours.....maybe you have the updated pump
OK, I feel better now. Haha. Thanks!
CrankyOldManWest Michigan · Oct 17, 2018#122There is definitely a difference in the appearance of the water pumps, but they're 1:1 compatible. I replaced the '08 xD with the superseded part number and it fits fine, just a pain to install because the pulley sticks out a few mm farther and interferes with the frame rail during install. Definitely better to replace it with the engine out of the car. =)
tmontagueCaledonia Ont. · Oct 17, 2018#123FWIW my wp looks identical to the one shown above and my engine was also from a 2011 corolla
ArmstrongRacingSan Diego · Oct 17, 2018#124Awww poop. Looks like from 2010 on the new pump was used. I remember when I did the pump on my 1nz the new part looked much different as well. Lots of Toyota water pump revisions apparently
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 17, 2018#125 Originally Posted by
CrankyOldMan ↑ There is definitely a difference in the appearance of the water pumps, but they're 1:1 compatible. I replaced the '08 xD with the superseded part number and it fits fine, just a pain to install because the pulley sticks out a few mm farther and interferes with the frame rail during install. Definitely better to replace it with the engine out of the car. =)
Thanks Sam! The bearing feels super smooth when spinning the pulley and there's absolutely no play at all in the bearing. I thought about replacing the water pump before installing the engine. I know you're not necessarily suggesting changing it but I did think about it.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 17, 2018#126 Originally Posted by
tmontague ↑ FWIW my wp looks identical to the one shown above and my engine was also from a 2011 corolla
Thanks Trevor!
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 17, 2018#127The local parts store counter guy is a font of knowledge. A month ago he sold a bunch of car A/C gear to the local applicance repair guy. He gave me his name. I called and he's coming down to my house in the next day or two to drain the refridgerant out of my A/C system. When my swap is done, he'll come and recharge the system. $150.00 for both on-site jobs. I think that sounds reasonable.
DarkShadowFoxMassachusetts · Oct 17, 2018#128 Originally Posted by
06YarisRS ↑ The local parts store counter guy is a font of knowledge. A month ago he sold a bunch of car A/C gear to the local applicance repair guy. He gave me his name. I called and he's coming down to my house in the next day or two to drain the refridgerant out of my A/C system. When my swap is done, he'll come and recharge the system. $150.00 for both on-site jobs. I think that sounds reasonable.
100-150 is the average price.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 17, 2018#129I was out in my garage tonight and did some rough measurements (not in units, but just using a piece of string) comparing the 1NZ and 2ZR. From the same point on the throttlebody to the outer edge of the alternator pully, I would make the 1NZ a couple of cm wider. Does this make sense? It appears as though there may actually be more space between the pully and the chassis. Does the 2ZR, when mounted sit more to the right (from the driver's position) in the engine bay? It isn't adding up for me at the moment.
Tomorrow - time permitting - I am going to raise the car up on 4 jackstands and start removing the front. It looks like the wiper cowl is going to be in the way. I would prefer to not remove it if possible. Did you guys remove the wiper cowl assembly when you did your swaps?
Also, I found out that the A/C compressor I bought is the wrong one. 🙁 It is from a 2011 and that will not work for two apparent reasons: 1) the 2011 compressor has two electrical connections, the scion harness and the 2009-2010 Corolla compressor, only 1 plug. 2) the A/C hose flanges on the compressor are a different configuration. So, it's back to the auto recycler. I hope they will take back the 2011 compressor and give me a 2009/10 one.
Here is the 2011 compressor:
Picture not included in this copy
This is the one I need:
Picture not included in this copy
ArmstrongRacingSan Diego · Oct 18, 2018#130Oh wow....... I had no idea there was another option. Are we sure that’s not from a different engine than the 2zr? I don’t ever remember seeing more than 2 wires to the a/c compressor in the corolla diagrams
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 18, 2018#131 Originally Posted by
ArmstrongRacing ↑ Oh wow....... I had no idea there was another option. Are we sure that’s not from a different engine than the 2zr? I don’t ever remember seeing more than 2 wires to the a/c compressor in the corolla diagrams
It appears so, Tom. Though I am now basing this off pictures from eBay. It seems that there was a change in the 2011 model year. I am going to go out again today and check the Yaris to be 100% sure that the flanges are the same as the 2009-2010 Corolla compressor. Thanks!
tmontagueCaledonia Ont. · Oct 18, 2018#132Hmm that is weird, I think I ordered a 2011 compressor only because I had a 2011 engine but never noticed a different compressor for a different year corolla
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 18, 2018#133 Originally Posted by
tmontague ↑ Hmm that is weird, I think I ordered a 2011 compressor only because I had a 2011 engine but never noticed a different compressor for a different year corolla
Yeah, strange. But my xd Harness only has one plug and this 2011 compressor has two. I checked the 2011 Corolla against the Yaris. The Yaris has the same flanges as the 2009 - 2010 compressor (one "T" shaped flange and "V" shaped flange for lack of better description) and definitely different than the compressor I got. Now, that said, maybe the auto recycler didn't actually give me the right one. However, every ebay listing shows a difference between 2009 - 2010 and 2011.
Thanks as always!
ArmstrongRacingSan Diego · Oct 18, 2018#134I did a quick google image search for the 2011 compressor and you get sites that show both as compatible, yet we know that’s not the case. Strange
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 19, 2018#135 Originally Posted by
ArmstrongRacing ↑ I did a quick google image search for the 2011 compressor and you get sites that show both as compatible, yet we know that’s not the case. Strange
Yes, there appears to be some confusion about the AC compressor as well as which belt to use. I picked up a Continental 6PK1230 (1060485) as it was the only one I could get last evening. There were a couple parts numbers for the same make, model year and options. On initial inspection, the belt seems short, but I should know tonight.
I returned my other AC compressor and got one from a 2010 Corolla. It has the proper flanges, which appear identical to the Yaris flanges. As a bonus, it was $60.00 cheaper. It also has the one needed connector. The pulley runs smooth and there is no runout or play but it makes a wee bit of what sounds like bearing noise when spinning the clutch pulley, though this may be normal sound from the clutchless mechanism. Not sure. I may have it checked at an AC shop before install. There was one broken mounting bolt left in the compressor with enough threads left to size the bolt. I measured the hole depth and figure I need about an 8 cm bolt (4 of them). I'd like to leave the AC compressor attached to the 1NZ. The only thing I'd like to try and source are some new o-rings for the AC hose connectors, but couldn't find a part number. May just pick up an o-ring kit.
Picture not included in this copy 06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 19, 2018#136 Originally Posted by
tmontague ↑ Hmm that is weird, I think I ordered a 2011 compressor only because I had a 2011 engine but never noticed a different compressor for a different year corolla
Thanks Trevor. I saw a reference online that alluded to something about a mid 2010 production change in the compressor. I'm still confused about the Japan-made and non-Japan made cars. It is all a bit confusing.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 19, 2018#137 Originally Posted by
DarkShadowFox ↑ 100-150 is the average price.
Thanks DarkShadowFox. I'm impressed that the guy will make two visits and charge the price for one.
ArmstrongRacingSan Diego · Oct 19, 2018#138 Originally Posted by
06YarisRS ↑ Thanks Trevor. I saw a reference online that alluded to something about a mid 2010 production change in the compressor. I'm still confused about the Japan-made and non-Japan made cars. It is all a bit confusing.
Great that you found this issue though, we all need to update our swap threads to reflect this new information.
CrankyOldManWest Michigan · Oct 19, 2018#139That would probably correlate to the change in wire harness part numbers for Canada as well.
tmontagueCaledonia Ont. · Oct 19, 2018#140So 2011+ compressors are good but older than that no go?
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 19, 2018#141 Originally Posted by
tmontague ↑ So 2011+ compressors are good but older than that no go?
I
think 2010 and older are ok, probably back to a certain point. I will try and dig up the reference I saw. It was something like before 10/2010 are ok. I don't want to provide misinformation, but from what I have seen, 2011 compressors are different in configuration. I suppose a car manufactured in 2010 is considered a 2011 model.
I wil try to determine with 100% accuracy this weekend which years work and which don't.
But for now...
Picture not included in this copy Just thought of something. Maybe both styles of compressor will work. Maybe only one connector needs to be used. As far as the flanges go, I thought there might be a "V" shaped connector on the end of the Yaris ac hose that attaches to the compressor. I now think that the "V" shaped flange is designed to receive a connector either straight or rotated at 90 degrees. Just some thoughts.
atomic_hojiKincardine, ON, Canada · Oct 19, 2018#142 Originally Posted by
06YarisRS ↑ Hey Adam. I've been popping in and out of your swap thread, and man, I have to say I thoroughly admire your skill, knowledge and tenacity. I'd probably have given up long ago.
...
lol - I appreciate the compliment, thanks. But then, if I was that clever, I'd have sorted it out by now.. 😛
Originally Posted by
06YarisRS ↑ Midpipe and Other Parts
Adam was right. This pipe starts out huge and then tapers down to 1 1/2" after the resonator. It is what it is. Hopefully the flow won't be restricted too much. As much as I hate the thought of it I'm tempted to gut the cats!
...
That looks (and sound by description) similar to the Walker pipe.. it functions, I just ended up monkey'ing with it more than I wanted to and am not a fan of the sound - but, depending on your preference, it might float your boat. 😁 Sounds like the local shop has the potential to do a nice setup for something decent. At least the back-end will be a smexy dual pipe setup. 😎
Quick note (catching up.. lol) re: anti-seize - just remember that torque specs are for clean, dry threads (unless otherwise noted, e.g. cylinder head bolts often list as with oil). When you gob anti-seize all over the threads you're reducing the thread friction, and especially putting a steel bolt into an aluminium block.. I've been fortunate that a little dab and a gentle torque I've never buggered anything up, but I have seen the result and it's no fun to resolve that mess.
Might sound ridiculous and seem obvious, but did you count the ribs on the pulley of the A/C compressor? Guess how I know that when you ask for an A/C compressor for 2ZR and they give you one from a (10th?) gen. Corolla and it doesn't seem to jive that it came from a 2AZ model... ooops. 😁
Looks like you're making awesome progress! Still diving into it this weekend?
-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 19, 2018#143 Originally Posted by
atomic_hoji ↑ lol - I appreciate the compliment, thanks. But then, if I was that clever, I'd have sorted it out by now.. 😛
That looks (and sound by description) similar to the Walker pipe.. it functions, I just ended up monkey'ing with it more than I wanted to and am not a fan of the sound - but, depending on your preference, it might float your boat. 😁 Sounds like the local shop has the potential to do a nice setup for something decent. At least the back-end will be a smexy dual pipe setup. 😎
Quick note (catching up.. lol) re: anti-seize - just remember that torque specs are for clean, dry threads (unless otherwise noted, e.g. cylinder head bolts often list as with oil). When you gob anti-seize all over the threads you're reducing the thread friction, and especially putting a steel bolt into an aluminium block.. I've been fortunate that a little dab and a gentle torque I've never buggered anything up, but I have seen the result and it's no fun to resolve that mess.
Might sound ridiculous and seem obvious, but did you count the ribs on the pulley of the A/C compressor? Guess how I know that when you ask for an A/C compressor for 2ZR and they give you one from a (10th?) gen. Corolla and it doesn't seem to jive that it came from a 2AZ model... ooops. 😁
Looks like you're making awesome progress! Still diving into it this weekend?
-- Adam
Adam!
Thanks for the guidance. I'm hoping that between the midpipe I got and the exhaust guy, I come up with a decent solution. I think the exhaust should look great, but my fear is the dreaded drone at highway speeds. Hopefully the pipe with 2 cats and the resonator will combat that.
I can only imagine how troublesome it would be to try to tap stripped threads in an aluminum block as a result of over torquing with a lubricant on the threads. I'll go a little easier on the torque for sure, and no doubt I've gone a little heavy on the anti-seize. At least I know which bolts I've torqued and knowing me, I'll likely check them all again after some driving time. But, thanks for that reminder, for sure.
Haha, going out to the garage in a few minutes to check the number of ribs on the pulley. I did score some M8x1.25 x 80mm bolts today and started to attach the compressor when I was summoned by wifey to go to hockey practice.
Looks like next weekend for the swap. I have one of our students, who's very diligent and careful when working on cars, interested in coming by next Saturday to help me put the engine in. I'll start the disassembly though through the week.
Thanks again for all your help. You can't imagine how valuable the help that I've gotten from you guys has been.
EDIT: Well, the compressor pulley has the right number of ribs and the belt I got is the right one. Tensioning mechanism works great. I'll back it off until is squeaks a bit then tighten it a bit. I imagine there's a certain amount of deflection under a certain pressure to be in spec, but I probably won't get that technical.
Picture not included in this copy 06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 19, 2018#144Plugs
I removed the plugs. I think I'll pick up a new set and install them. I'm not really knowledgeable about plug condition, so feel free to comment. The bottom right one doesn't look so great imo.
Picture not included in this copy
ArmstrongRacingSan Diego · Oct 19, 2018#145Plugs look ok, they’re iridium so they last a long time. I put new plugs in mine when I got it because who knows if the maintenance was done of even if the mileage was recorded correctly.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 19, 2018#146 Originally Posted by
ArmstrongRacing ↑ Plugs look ok, they’re iridium so they last a long time. I put new plugs in mine when I got it because who knows if the maintenance was done of even if the mileage was recorded correctly.
Thanks Tom. I'm glad they don't suggest some underlying mechanical issue. It occured to me - after I replaced all the plugs and coils - that I should have put my breaker bar on the crank pulley given it a turn or two. Oh well, haha.
I'm about to order some more Rock Auto stuff including plugs, oil filters, a dessicant bag for the A/C. There's a guy locally selling an oil filter wrench for the cartridge style filter assembly and I can pick that up for $8.00 CAD.
tmontagueCaledonia Ont. · Oct 20, 2018#147The OEM plugs are good for 160k km iirc. Mine looked similar to yours and I kept them in.
I changed the valve cover gasket and spark plug hole seals as those tend to leak down the road. It actually looks like that may be happening in your one spark plug hole of your darker plug. Those plugs look pretty good though
That said, the spark plug hole seals are such a tight tolerance they are almost impossible to remove without damaging the cover and install is ever harder. Not sure how a toyota tech would do it but it almost seems as if you need a special press for them. They are such a tight fit
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 20, 2018#148 Originally Posted by
tmontague ↑ The OEM plugs are good for 160k km iirc. Mine looked similar to yours and I kept them in.
I changed the valve cover gasket and spark plug hole seals as those tend to leak down the road. It actually looks like that may be happening in your one spark plug hole of your darker plug. Those plugs look pretty good though
That said, the spark plug hole seals are such a tight tolerance they are almost impossible to remove without damaging the cover and install is ever harder. Not sure how a toyota tech would do it but it almost seems as if you need a special press for them. They are such a tight fit
Thanks Trevor. I believe that the darker plug was from the far left cylinder when standing at the exhaust manifold side of the engine. This plug seemed a bit looser than the others. It took very little force to remove it. I snugged it up better. Maybe I should wait before buying new ones and see if it runs well. Although I like the idea of new plugs, I'd hate to throw away perfectly good ones.
tmontagueCaledonia Ont. · Oct 20, 2018#149There no harm is replacing them and trust me when I say it is easier when the engine is out of the car. The wiper shroud is in the way of a long ratchet when doing it in the car so it is not as simple as on the 1nz. But in all honesty iridium plugs are not necessarily cheap and they last a long time. I kept min in for a whole year of tracking the car and didn't replace them until midway through this year when they had 130k km on them. They still looked great and I noticed no difference with new ones. Imo I'd keep them in the cat until the owners manual stated yo replace them
O and I forgot to chime in on one if your previous Q's - 100% remove the wiper shroud and metal shield before doing the swap it opens of a ton if space right back to the fire wall. If you have an air ratchet or cordless ratchet it will make quick work if the 10mm bolts holding it in
ArmstrongRacingSan Diego · Oct 20, 2018#150Trevor just reminded me, the plate on the back of the timing cover does leak on mine. I would reseal that for sure. It’s at the top of the engine, on the back about where the exhaust manifold is. It’s a cover to access the chain tensioner