Yarisworld Archive

06YarisRS's 2ZR-FE Swap 5-Door Hatchback (Automatic Transmission)

448 posts · 301,527 views · page 7 of 9

Replies continued

06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 3, 2018#301
Haha, thanks Adam. Given the support/time investment that you guys generously provided me, I think a little smack down is a minor price to pay. Lol. Oh yeah, and a person has to have pride in the first place to really take offense. 😆

Got hockey practice today, a few other family commitments, and a few odds and ends to tie up on the car, so first drive looks like tomorrow.
Thanks again for all your help, Adam. It has been an experience.
tmontagueCaledonia Ont. · Nov 3, 2018#302
I plan on making a new 2zr swap thread with just the specific info regarding electrical hook up and what to do with the xd vs yaris harness and grounds.

I will keep it just to those specifics and avoid the stuff about how to pull an engine as that is on all the other swap threads.

This was probably the one part I wasnt sure about as it isn't in one section of the swap threads and until I had my harness to look at it was a big question mark for me
ArmstrongRacingSan Diego · Nov 3, 2018#303
Originally Posted by 06YarisRS ↑
No codes after 10 minutes of running!!!
Sweet baby Jesus.....we finally got it.

Trevor I think you have a good idea regarding the electrical, clear pictures and instructions on that is definitely needed
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 3, 2018#304
Originally Posted by ArmstrongRacing ↑
Sweet baby Jesus.....we finally got it.

Trevor I think you have a good idea regarding the electrical, clear pictures and instructions on that is definitely needed
Yes! It is running strong, free of MILS. The idea to create an electrical thread is a great one. I know that it will help others in the future. I have hundreds of pictures, so, Trevor, if you need any in particular, I'd be happy to provide any needed. It's the least I could do to contribute.
ArmstrongRacingSan Diego · Nov 3, 2018#305
We also need a moderator to remove the wrong wiring picture in brushforhires thread...

I was caught sleeping by that one
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 3, 2018#306
Apparently not out of the woods yet.

On my latest start up, I ran the car for about 1/2 an hour to check my plumbing for leaks. Everything was good. I went back out and started the car and my P2770 is back. I cleared the codes and it returns with each startup. The car has started and run at least 3-4 times without displaying any codes. I am going to recheck all of my connections, but I soldered and heat shrinked all of them with pin 9 grounded. I have full charging and my transmission is grounded - 12.6V at terminals and 12.6V from trans case to positive. This is very strange as I've had several startups and no codes. It must be a bad connection. I'll sand down the contact point on the transmission case where the ground attaches. Will report back after I recheck everything.

Tests completed:

1) have continuity on the blue wire as I repaired it (ECM Pin 78 to C29 pin 10), so my blue wire is good.

2) have continuity from ring terminal on brown wire to female pin 9 in connector C29, so my ground is good. I removed the ring terminal from the block for this test.

3) sanded and tested the ground on the trans case 12.6v tested at the battery and 12.6v using positive battery post and ground.

Observations: If I disconnect the battery terminal for a few minutes, then come back and start the car, it does not light up the MIL, but Torque registers a pending code of P2770. On the second start, the MIL comes on and Torque shows a current fault P2770.

Picture not included in this copy

Looking at the diagram for the xD, is it possible that brushforhire was right and it is the blue wire that needs grounding? I didn't have trans ground when I tried the blue wire. Pin 10 in the pic below looks like to goes to ground but I'm still in the learning phase about wiring diagrams. EDIT: Blue wire grounded gives the same code.

Picture not included in this copy
ArmstrongRacingSan Diego · Nov 3, 2018#307
This is confusing because My harness is the same as yours.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 3, 2018#308
Thanks Tom. Defintely the same configuration, but different wires. Not sure if they serve the same functions as I haven't looked at the Corolla diagrams much.

Down the rabbit hole...

If I actually got a 2008 xD ECU, then it appears - in its stock form- to be incompatible with both my harness and transmission. For one thing the 2008 ECU only appears to feed 8 wires to the connector. And, the SLT+ and SLT - pins are not the same between my Yaris and the xD harness.

From what I'm seeing - from my limited understanding - I need a different ECU, or figure out if the one I have will work and I need to swap some pins in the harness at the ECU. I still have to look at my ECU overall to be sure that those spots even have pins and if they are assigned to something else.

I will try to refrain from asking a lot of questions as I've done an awful lot of that over the past couple months. But, feel free to chime in if you are so inclined.

Once this is all over, I'll spend some time cleaning up my thread.

Picture not included in this copy
ArmstrongRacingSan Diego · Nov 4, 2018#309
Wow. I apologize. I wasn’t aware they changed the pins in 2011. So it looks like you need to do the same pin swap I had to at the ECM. Here is the link to how I did it:
The 2zr-fe engine swap guide

So it looks like at some point they started using corolla parts on the xD, right before it was discontinued. Great work pulling up the info!
ArmstrongRacingSan Diego · Nov 4, 2018#310
If you want to know how all of these ECTS wires work and why ill give a brief explanation. Each one of the inputs corresponds to a solenoid, these solenoids move when activated by the ECM and allow line pressure(about 800psi) to activate their wet clutches. The holding and releasing of these clutches manipulate how the planetary gears "simulate" gears.
Picture not included in this copy

Solenoids are just an electrical load device, they need a positive and negative circuit to operate. Just like a bulb, here we're moving wires around in the harness to make those solenoid circuits complete.

The Yaris ETCS has a different layout than ALL of the 1.8L cars due to its sub-compact nature. So we are never going to have a simple "plug-n-play" AT swap.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 4, 2018#311
Originally Posted by ArmstrongRacing ↑
Wow. I apologize. I wasn’t aware they changed the pins in 2011. So it looks like you need to do the same pin swap I had to at the ECM. Here is the link to how I did it:
The 2zr-fe engine swap guide

So it looks like at some point they started using corolla parts on the xD, right before it was discontinued. Great work pulling up the info!
Thanks Tom! I really appreciate the explanation of how it works. How could you possibly be aware of every change that is made by the manufacturer? I just looked at your link to your pin swap.

It looks like I do have to swap 57 to 58. The 2008 xD does not reference Pin 9 at all. I wonder if that is why it is grounded. There is no mention of SLU+ and SLU- on the 2008 pinout. I wonder if I need a different ECU.

Here is an update picture that includes a 2009 Corolla. As far the 2009 Corolla and 2011 xD ECTS is concerned, the pins are identical. I still can't get my head around the changes in the xD ECU between 2008 and 2011.

I am wondering if I should just go out and do as you say - switch 57 to 58, ground 9 and test it.

Picture not included in this copy
atomic_hojiKincardine, ON, Canada · Nov 4, 2018#312
At work, can't play with diagrams, but given what you have there I can see your problem..

All pins trans side are consistent in function (same trans), BUT - pin 9 should be ground as Tom noted; the 2008 ECM doesn't supply an SLU-, it uses a local ground instead it looks like.

At the ECM the 2008 and 2011 xD differs on pins for SLU+/- and SL. Pin 57 on your 2011 harness needs to move to pin 58 to match the 2008 ECM; you've already cut the wire at pin 77 - just make sure it's not used elsewhere and is taped and isolated to avoid issues..

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 4, 2018#313
Thanks Adam! I'm going to do the swaps as per Tom's and your directions. At hockey again today, so it will be a bit later. I'm going to practice removing ECU pins on my Yaris harness before tackling the xD harness in the car.

I will definitely post back with the results.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 4, 2018#314
I cannot for the life of me get these darn terminals out! I am practicing on my spare Corolla harness that came with my engine. I'm in the correct release hole, wiggling the safety pin around, the white slide lock is pushed out the required mm. Maybe my pin is too small. I've looked at a close up pic of the actual terminal.

Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 4, 2018#315
OK, finally managed to get a couple of pins out. How easily should they come out? It took a bit of force and made a little snap sound. The terminal appears undamaged.
atomic_hojiKincardine, ON, Canada · Nov 4, 2018#316
My experience is that usually if the retaining bar/clip is fully disengaged and the pin has the internal clip out of the way a bit of a gentle tug will slide it out. Generally force and a snap sound means the plastic internal clip is busted. You can check by reinserting the terminal - it will feel sloppy if broken..

Good news is you're pulling out of one and into another pin slot, so if you break the internal clip you're probably OK, as long as you don't damage the metal terminal; and/or no other terminal needs to use that pin slot.

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 4, 2018#317
Originally Posted by atomic_hoji ↑
My experience is that usually if the retaining bar/clip is fully disengaged and the pin has the internal clip out of the way a bit of a gentle tug will slide it out. Generally force and a snap sound means the plastic internal clip is busted. You can check by reinserting the terminal - it will feel sloppy if broken..

Good news is you're pulling out of one and into another pin slot, so if you break the internal clip you're probably OK, as long as you don't damage the metal terminal; and/or no other terminal needs to use that pin slot.

-- Adam
Thanks Adam! Well, it is done, but I wouldn't call the pin removal easy. LOL! Of course, since I was doing it on the car, despite my best effort to save the wee rubber plug, it found a new home somewhere in the engine bay! I used a very fine tip on my tube of rtv sealant and put a small dab in the newly opened hole.

Standby for a pic!
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 4, 2018#318
A picture is worth a thousand words...

Picture not included in this copy

Thank you gentlemen!!! It was the pin swap from 57 to 58 that cleared the codes. I had 5 - 6 starts, running 5 - 10 minutes each, a similar number of scans and not one MIL, except of course when I jumped in and fired it up without putting the intake tube back on. I got MAF error, but that disappeared after re-install and startup.

I redid conduit and tape around the trans connectors and ziptied everything. It looks great.

One other thing I'd like to do is slightly bend my transmission dipstick tube a touch toward to the driver's side. It's hard to get out past the upper rad hose.

Here is a pic with everything (in the engine bay, at least) put back together.

Picture not included in this copy

I am just so itching to take this bad boy for a run.
atomic_hojiKincardine, ON, Canada · Nov 4, 2018#319
Virtual high five buddy! 👍 glad you got it sorted out.

Now get out and go for a rip.. 😁

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 4, 2018#320
Originally Posted by atomic_hoji ↑
Virtual high five buddy! 👍 glad you got it sorted out.

Now get out and go for a rip.. 😁

-- Adam
Thanks Adam! Rip will likely happen tomorrow evening. Gotta get all the panels and such back on.
ArmstrongRacingSan Diego · Nov 4, 2018#321
Huge congrats to you sir for figuring this out!
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 4, 2018#322
Originally Posted by ArmstrongRacing ↑
Huge congrats to you sir for figuring this out!
Thanks Tom, but it was you who figured it out originally! I was just riding on your coat tails. You guys have been simply awesome, from my initial inspiration to do the swap, down to the technical details. It's definitely a different thing to break new trail, than to copy what others have done. That said, I'm pretty happy I managed to pull it off. In my first post, I said it would be the most involved car-related project I've done, and that it was. Haha.

Now...time to start in on learning to beef up the 1NZ internals for forced induction....joking! 😆
tmontagueCaledonia Ont. · Nov 4, 2018#323
Congrats on the swap! Enjoy a much needed sleep lol

I'm surprised the 2011 harness is different then the 2008, guess we all learned something new on this swap. This is also one of the reasons I want to put out a thread going over these things.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 5, 2018#324
Originally Posted by tmontague ↑
Congrats on the swap! Enjoy a much needed sleep lol

I'm surprised the 2011 harness is different then the 2008, guess we all learned something new on this swap. This is also one of the reasons I want to put out a thread going over these things.
Thanks. Yes, I too was surprised but ultimately thankful that it just required the pin swap. Maybe a quick review of wiring diagrams before posting could confirm any other differences in the years if there are any. I could do that as a contribution.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 5, 2018#325
The auto recycler where I got my used alternator, A/C compressor and engine cover is going to give me a different compressor. So, instead of slapping all the body parts back on tonight, I'm going to remove the compressor. Yet another delay to my first test drive. 😢
ern-dizCA all day · Nov 6, 2018#326
Soon...sooooon...
ArmstrongRacingSan Diego · Nov 6, 2018#327
One thing I will add based on my experience with the auto...

The ECM is adaptive, this means it will build fuel trim maps and shift patterns based on YOUR driving habits.

My wife would drive my car most of the time, so when I got in it the car felt sluggish due to her conservative driving. Once I was able to drive the car a while, the performance feeling returns.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 6, 2018#328
Originally Posted by ern-diz ↑
Soon...sooooon...
I know. This stupid compressor is messing with my fun. 🙄

Looking forward to the following on my first drive:

1) smoother, more robust acceleration
2) no clunks, clanks, knocks
3) cruise control testing
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 6, 2018#329
Originally Posted by ArmstrongRacing ↑
One thing I will add based on my experience with the auto...

The ECM is adaptive, this means it will build fuel trim maps and shift patterns based on YOUR driving habits.

My wife would drive my car most of the time, so when I got in it the car felt sluggish due to her conservative driving. Once I was able to drive the car a while, the performance feeling returns.
Ah Ha! Clearly then there is only one acceptable driving style. 😆

I'm more of an accelerate fast, but not burnout kind of guy...at least since getting older. So, say, routinely running up close to redline at WOT off a ramp onto the highway for example shouldn't adversely affect either my engine or trans, then?
ArmstrongRacingSan Diego · Nov 6, 2018#330
I use WOT regularly as prescribed by my physician
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 6, 2018#331
Originally Posted by ArmstrongRacing ↑
I use WOT regularly as prescribed by my physician
👍 I'm guessing mine is going to say the same at my next appointment.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 6, 2018#332
5 minute job removing the a/c compressor. The little plastic panel next to the radiator pops out easily with the removal of two plastic pins and creates a good sized window to the compressor, water pump etc. Excellent design on behalf of Toyota. I still think that changing out a water pump with the 2ZR shoehorned in there will be a royal pain in the butt.
ArmstrongRacingSan Diego · Nov 7, 2018#333
#7
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 7, 2018#334
Initial observations:

Much more refined feel. The engine is much smoother and the valve train is almost inaudible.

The car pulls hard right up to about 6000 rpm before it shifts. Does it push you back into your seat? Not exactly, but it's definitely more potent than the 1.5.

It's much more 'torquey', if that's a word.

Shifting is precise.

My little aging Yaris (with 180000 kms) now has an engine with around 70000 kms!

Am I impressed? Damn straight!

Please excuse both the mess and the crappy pic quality.

Picture not included in this copy


I have a small exhaust clunk as the muffler, on some bumps and harder cornering is hitting the spring seat, but I think this is a quick fix when I get the exhaust work done. EDIT: The muffler is just turned a bit counterclockwise. My midpipe is in two sections (for shipping, I assume) so I just need to loosen the clamp, level the muffler and retighten. I expect that the new exhaust will allow the engine to breathe a little better. That oem muffler and piping is so tiny.

The 'new' used ac compressor is virtually silent.

As a major bonus, the cruise control is fully functional!

So, to Tom, Trevor, Adam and Sam (not in any particular order), a huge THANKS for helping me through this!!!
ArmstrongRacingSan Diego · Nov 7, 2018#335
I’m glad you took on this swap, we all learned something new and you now has a legit RS(nice badge!)

I wish I have a plaque or badge....or anything to give you as a welcome to the 2zr fam.

But sadly I never had anything made
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 7, 2018#336
Originally Posted by ArmstrongRacing ↑
I’m glad you took on this swap, we all learned something new and you now has a legit RS(nice badge!)

I wish I have a plaque or badge....or anything to give you as a welcome to the 2zr fam.

But sadly I never had anything made
Thanks Tom! It's so cool. So glad I did the swap. Now...I get to update my sig. 👍
WeeYariGeorgetown, Ontario, Canada · Nov 8, 2018#337
Originally Posted by ArmstrongRacing ↑
you now has a legit RS(nice badge!)
More legit...find yourself a TS badge. Got one in my garage but it's pretty beat up.

Sent from my EML-L09 using Tapatalk
CrankyOldManWest Michigan · Nov 8, 2018#338
Originally Posted by 06YarisRS ↑
The car pulls hard right up to about 6000 rpm before it shifts. Does it push you back into your seat? Not exactly, but it's definitely more potent than the 1.5.

It's much more 'torquey', if that's a word.

...

So, to Tom, Trevor, Adam and Sam (not in any particular order), a huge THANKS for helping me through this!!!
Always glad to help, especially when someone is pioneering a new variant!

Agreed, it's not sports car level acceleration, but it's there all the way to redline. My favorite part is the way it loves to pull several hundred pounds of trailer and a hatch full of tools. =)
ern-dizCA all day · Nov 8, 2018#339
Too cool 👏
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#340
Originally Posted by WeeYari ↑
More legit...find yourself a TS badge. Got one in my garage but it's pretty beat up.

Sent from my EML-L09 using Tapatalk
I really like that idea, WeeYari. I think I may start looking. Does that badge go in the same place as the RS badge and would it attach in the same manner?
ArmstrongRacingSan Diego · Nov 8, 2018#341
Originally Posted by WeeYari ↑
More legit...find yourself a TS badge. Got one in my garage but it's pretty beat up.
Oh right TS. I’m so confused now with all the different home-made versions we’ve created here...

1nz built n/a
1nz supercharged
1nz turbo
1nz with 6 speed
And
2zrfae swap
2zr with auto
2zr with 5 speed
2zr with 6 speed
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#342
Originally Posted by CrankyOldMan ↑
Always glad to help, especially when someone is pioneering a new variant!

Agreed, it's not sports car level acceleration, but it's there all the way to redline. My favorite part is the way it loves to pull several hundred pounds of trailer and a hatch full of tools. =)
Thanks Sam! One of the things I was looking for in the swap is more torque for highway cruising. I never found the 1.5 to be particularly underpowered, but it would downshift on longer, steeper hills. I haven't actually had it out on the highway yet, so can't comment on that , but your comment about carrying extra mass around makes me optimistic. I do think there is something in the programming for the cruise control that makes the car downshift before it needs to. I have rolled up long hills with the cruise off and rarely had to drop a gear to maintain speed. Something tells me that despite the swap - and extra torque - that this behaviour won't change.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#343
Originally Posted by ern-diz ↑
Too cool 👏
Thanks ern-diz! It is awesome!
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#344
Originally Posted by WeeYari ↑
More legit...find yourself a TS badge. Got one in my garage but it's pretty beat up.

Sent from my EML-L09 using Tapatalk
Like this?

Picture not included in this copy

There is this, but it looks like a peel-and-stick only. I would need one that attaches to the grille.

https://www.ebay.co.uk/p/TRD-T-Sport...p2047675.l2644

Looks like I found the actual badge (Toyota 75301-52010) in the UK, but it will not ship overseas.
WeeYariGeorgetown, Ontario, Canada · Nov 8, 2018#345
The actual bolt fastened badge is a unicorn on these shores. May have to buddy up with one of our UK friends to arrange an acquisition.

Sent from my EML-L09 using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#346
Originally Posted by WeeYari ↑
The actual bolt fastened badge is a unicorn on these shores. May have to buddy up with one of our UK friends to arrange an acquisition.

Sent from my EML-L09 using Tapatalk
Excellent idea! May have to make a post about it.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#347
I went out for another drive this evening and I'm impressed. Took it out on the highway and found the steepest hill I could. I set the cruise control at 120 km/h. With the 1NZ and cruise set, it would always drop a gear. The 2ZR powers up the hill without a gear drop and not even a detectable increase in rpm. Awesome!

I was under the back of the car rigging up a bungy cord on the hanger to stop the clunking just for tonight. I had a look at the midpipe and I'm thinking I ought to have the exhaust shop chop the pipe at the resonator and upsize the pipe to the rear flange at the axle. Maybe to 2" or 2.25". I know that my muffler will be much more free flowing than the stock muffler, but I can't help but think that that midpipe is really restrictive. Taking into consideration what you have all said - and done - as well as reading a thread by 'the barber', I'm thinking this is the route to go. I've heard that a freer flowing (maybe too free-flowing) exhaust can adversely affect torque and I wouldn't want to lose any of that. Thoughts/comments welcome as always.
ArmstrongRacingSan Diego · Nov 8, 2018#348
I did an extensive amount of research on this topic back when I did my swap too. I ended up using a magnaflow resonator and muffler, and 2.25in piping. The 2.5in pipe is where you start losing torque according to the internet dyno charts.

I have a video of my dyno run as proof that I didn’t loose any torque
ern-dizCA all day · Nov 8, 2018#349
Originally Posted by 06YarisRS ↑
I went out for another drive this evening and I'm impressed. Took it out on the highway and found the steepest hill I could. I set the cruise control at 120 km/h. With the 1NZ and cruise set, it would always drop a gear. The 2ZR powers up the hill without a gear drop and not even a detectable increase in rpm. Awesome!

I was under the back of the car rigging up a bungy cord on the hanger to stop the clunking just for tonight. I had a look at the midpipe and I'm thinking I ought to have the exhaust shop chop the pipe at the resonator and upsize the pipe to the rear flange at the axle. Maybe to 2" or 2.25". I know that my muffler will be much more free flowing than the stock muffler, but I can't help but think that that midpipe is really restrictive. Taking into consideration what you have all said - and done - as well as reading a thread by 'the barber', I'm thinking this is the route to go. I've heard that a freer flowing (maybe too free-flowing) exhaust can adversely affect torque and I wouldn't want to lose any of that. Thoughts/comments welcome as always.
I'm by no means an expert but from what I understand, you want to be able to tune to the air/fuel flow. Since these cars are next to impossible to tune, I've stayed away from intake/exhaust mods out of fear of actually losing BHP and/or torque rather than gaining. The noises it would make might be nice but without gains, or worse yet, with losses, I don't see the point.
ArmstrongRacingSan Diego · Nov 8, 2018#350
Also

If you find those TS badges I’ll buy one for everyone on here with a swap. It’s the least I can do to show my appreciation for all the support of everyone here.