Yarisworld Archive

06YarisRS's 2ZR-FE Swap 5-Door Hatchback (Automatic Transmission)

448 posts · 301,527 views · page 8 of 9

Replies continued

06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#351
Originally Posted by ArmstrongRacing ↑
I did an extensive amount of research on this topic back when I did my swap too. I ended up using a magnaflow resonator and muffler, and 2.25in piping. The 2.5in pipe is where you start losing torque according to the internet dyno charts.

I have a video of my dyno run as proof that I didn’t loose any torque
Excellent. Thanks Tom! I'll check out your video. It would be great to have a comparison between the stock exhaust and a freer flowing one. Barber said he noticed no difference with just the muffler, but the midpipe made a noticeable difference, but I think, if I recall correctly, that was on a 1.5.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#352
Originally Posted by ern-diz ↑
I'm by no means an expert but from what I understand, you want to be able to tune to the air/fuel flow. Since these cars are next to impossible to tune, I've stayed away from intake/exhaust mods out of fear of actually losing BHP and/or torque rather than gaining. The noises it would make might be nice but without gains, or worse yet, with losses, I don't see the point.
Thanks ern-diz. Minimally, I'd like to get back to what the stock xD exhaust was. The used eBay midpipe I almost got looked mandrel bent and much more free-flowing than the aftermarket one I bought. As Adam mentioned earlier in the thread, these aftermarket ones (He mentioned the Walker in particular) have significant restrictions in the bends. He was definitely right about that!
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#353
Originally Posted by ArmstrongRacing ↑
Also

If you find those TS badges I’ll buy one for everyone on here with a swap. It’s the least I can do to show my appreciation for all the support of everyone here.
Huh? I think I should be buying them 😆 I will keep looking and let you know if I come up with anything.

EDIT: Following up on a lead now. I've emailed a UK eBay seller. Will let you know. I need to confirm if this is what we're looking for:

https://www.ebay.co.uk/p/Toyota-7530152010/652635220

And this, but with different coloring and part number (and actual pic of back):

http://vi.raptor.ebaydesc.com/ws/eBa...29206000&ver=0

I can only find pics of the front of the badge online. There is a cheaper one (4.99 pounds) but I think it's a sticker. The listing above refers to placement on the front of the car.
atomic_hojiKincardine, ON, Canada · Nov 8, 2018#354
Torquey == broke loose in 3rd gear this morning; yes, it was wet.. 😆

Glad to hear you're enjoying the new found, smooth power of the 2ZR!

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#355
Originally Posted by atomic_hoji ↑
Torquey == broke loose in 3rd gear this morning; yes, it was wet.. 😆

Glad to hear you're enjoying the new found, smooth power of the 2ZR!

-- Adam
2ZR-FAE 139 - 148 HP! I bet it can break loose! You must feel a significant difference from stock.

I am definitely loving the 2ZR. Car feels a lot lighter. 👍
stidnamAustralia · Nov 8, 2018#356
An alternate part number for that badge you're after is

75312-52060

Im not sure what the differences are but both badges can be had for $30 AUD from amayama.com

Can get pictures from the parts catalogue this evening if needed.

:)
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#357
Originally Posted by stidnam ↑
An alternate part number for that badge you're after is

75312-52060

Im not sure what the differences are but both badges can be had for $30 AUD from amayama.com

Can get pictures from the parts catalogue this evening if needed.

:)
Thank you, Stidnam! Just checked that out. Definitely a possibility. It looks like shipping would be killer from no matter where.
tmontagueCaledonia Ont. · Nov 8, 2018#358
Originally Posted by 06YarisRS ↑
Like this?

Picture not included in this copy

There is this, but it looks like a peel-and-stick only. I would need one that attaches to the grille.

https://www.ebay.co.uk/p/TRD-T-Sport...p2047675.l2644

Looks like I found the actual badge (Toyota 75301-52010) in the UK, but it will not ship overseas.
I have that badge on my trunk, after about a year the red faded and crack/chipped, looks ok but cheap as hell

I initially had a 2.5" and can confirm the loss in torque according to my butt dyno. I went back and got 2.25" and I'm all smiles now
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#359
Originally Posted by tmontague ↑
I have that badge on my trunk, after about a year the red faded and crack/chipped, looks ok but cheap as hell

I initially had a 2.5" and can confirm the loss in torque according to my butt dyno. I went back and got 2.25" and I'm all smiles now
Yeah, I'm sure the cheapie ones are junk. Hopefully, the Toyota part would be much better made.

Thanks for your experience with the exhaust. I'm thinking 2.25", since it will be crush bent, would be my best bet. I found a place that will do the exhaust with a day or two notice. I'll probably make an appointment for the beginning of the week.
stidnamAustralia · Nov 8, 2018#360
Not sure how much shipping is coming to for you, but 5 of those badges shipped to my address in Aus is only $8.50 AUD
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 8, 2018#361
Originally Posted by stidnam ↑
Not sure how much shipping is coming to for you, but 5 of those badges shipped to my address in Aus is only $8.50 AUD
Yeah, it's fairly expensive given the size and weight of the package. Now, we could probably get combined shipping.

Picture not included in this copy
ArmstrongRacingSan Diego · Nov 9, 2018#362
Originally Posted by 06YarisRS ↑
Yeah, it's fairly expensive given the size and weight of the package. Now, we could probably...
I'm on board, PM me with your paypal info
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 9, 2018#363
Originally Posted by ArmstrongRacing ↑
I'm on board, PM me with your paypal info
I found a much better price Tom. The guy from England emailed me back and he can deliver 6 of these emblems for $120.00 USD. Maybe we could have them delivered to a central location and redistribute from there. Or, I could ask him shipping quotes for each individual piece to different addresses. If you can PM me an email address, I can send you the email. I'm not sure how many we need all together, and maybe the guy could offer a similar deal for a smaller number.

EDIT: Here is link to the listing he created:

https://www.ebay.com/sch/i.html?_fro...01565&_sacat=0

I would like to contribute financially. I would also offer to receive them and mail them out to the recipients.

Thanks

Just to confirm, here are the pics of his product:

Picture not included in this copy

Picture not included in this copy
WeeYariGeorgetown, Ontario, Canada · Nov 9, 2018#364
Be warned guys.

The sedan and hatch do not share the same front grill insert design. I'm willing to bet that the clip in badge will only work on the hatch. I have seen another badge which mounts via a single pass thru bolt which facilitates universal mounting.

Sent from my EML-L09 using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 9, 2018#365
Originally Posted by WeeYari ↑
Be warned guys.

The sedan and hatch do not share the same front grill insert design. I'm willing to bet that the clip in badge will only work on the hatch. I have seen another badge which mounts via a single pass thru bolt which facilitates universal mounting.

Sent from my EML-L09 using Tapatalk
Oh my. I hadn't thought of that. Excellent point. We will clearly have to rethink this.
ArmstrongRacingSan Diego · Nov 9, 2018#366
Originally Posted by 06YarisRS ↑
Oh my. I hadn't thought of that. Excellent point. We will clearly have to rethink this.
I’m not worried,anyone who’s done the swap can surely modify a badge. It’s only Trevor and I with Sedans.

Im still interested, let me know how to proceed
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 9, 2018#367
Originally Posted by ArmstrongRacing ↑
I’m not worried,anyone who’s done the swap can surely modify a badge. It’s only Trevor and I with Sedans.

Im still interested, let me know how to proceed
Excellent. Thanks Tom. Shall we order all 6? I would like to cover 1/2 of the cost. I can go ahead and place the order. We just need to decide where to send them.

Adam
ern-dizCA all day · Nov 9, 2018#368
I wanna be part of the TS crew 😢
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 9, 2018#369
Originally Posted by ern-diz ↑
I wanna be part of the TS crew 😢
Picture not included in this copy
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 9, 2018#370
Just scored on eBay $100.00 + $50.00 shipping...

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
DarkShadowFoxMassachusetts · Nov 10, 2018#371
Originally Posted by 06YarisRS ↑
Just scored on eBay $100.00 + $50.00 shipping...

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
*deep fart can noise*
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 10, 2018#372
Originally Posted by DarkShadowFox ↑
*deep fart can noise*
Seriously? Is it going to sound like a fart can? I don't like the sound of that, literally and figuratively.
ArmstrongRacingSan Diego · Nov 10, 2018#373
Originally Posted by 06YarisRS ↑
Seriously? Is it going to sound like a fart can? I don't like the sound of that, literally and figuratively.
I don’t think so, as long as you keep 1 resonator you should be fine
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 10, 2018#374
Originally Posted by ArmstrongRacing ↑
I don’t think so, as long as you keep 1 resonator you should be fine

Thanks. That's good to know. I will definitely be keeping the resonator and both cats. Just need to upsize the pipe from the resonator to the axle.
DarkShadowFoxMassachusetts · Nov 10, 2018#375
Originally Posted by 06YarisRS ↑
Thanks. That's good to know. I will definitely be keeping the resonator and both cats. Just need to upsize the pipe from the resonator to the axle.
i dunno i was being silly. id keep your cats and stuff otherwise its just going to be all noise. c:

myself
tmontagueCaledonia Ont. · Nov 10, 2018#376
Yup keep the resonator for sure, it's a well flowing 2 5' open pipe iirc and it does a lot to remove the rasp
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 10, 2018#377
Originally Posted by DarkShadowFox ↑
i dunno i was being silly. id keep your cats and stuff otherwise its just going to be all noise. c:

myself
😆

I will indeed keep the cats and resonator. Thanks!
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 10, 2018#378
Originally Posted by tmontague ↑
Yup keep the resonator for sure, it's a well flowing 2 5' open pipe iirc and it does a lot to remove the rasp
👍 I have a question for ya.

Before I found the Megan axleback- and was going to use that other muffler I got - I had talked to an exhaust shop. They said that I should remove the flanges at the muffler and end of the midpipe and have on continuous pipe, bent over the axle. I don't really like the idea of hacking the end off the Megan and welding directly to it. What would you do in this case? If the Megan is designed to attach to stock Yaris exhaust, it must be a smaller diameter, wouldn't it. Would this small area of smaller diameter cause a restriction in flow?
ArmstrongRacingSan Diego · Nov 11, 2018#379
My exhaust shop did this as well. Cut the flange off and did a solid 2.25” from the resonator. I haven’t had to remove it so I cant comment of serviceability once it’s all solid
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 11, 2018#380
Originally Posted by ArmstrongRacing ↑
My exhaust shop did this as well. Cut the flange off and did a solid 2.25” from the resonator. I haven’t had to remove it so I cant comment of serviceability once it’s all solid
Yeah, the exhaust shop said that it just eliminates another point where leaking can happen, which definitely makes sense to me. This shop only uses aluminized pipe and does not mandrel bend, but this Yaris will never see the salty roads of winter. I also think that 2.25" will give good flow even though it's crush bending.

I bet it would make removing the pipe a little more difficult, or even impossible if it's welded, but it can always be cut again and rewelded if need be.
tmontagueCaledonia Ont. · Nov 11, 2018#381
The exhaust shop i went to also welded everything solid. Personally I'm not a fan. The gaskets with spring bolts add a section where it can flex under stress. This is one of the reasons my muffler weld snapped after 3 years when I was at the track.

I also like to be able to remove the exhaust in pieces if I need to service anything. I hate not being able to do thatvwithba solid one piece exhaust.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 11, 2018#382
Originally Posted by tmontague ↑
The exhaust shop i went to also welded everything solid. Personally I'm not a fan. The gaskets with spring bolts add a section where it can flex under stress. This is one of the reasons my muffler weld snapped after 3 years when I was at the track.

I also like to be able to remove the exhaust in pieces if I need to service anything. I hate not being able to do thatvwithba solid one piece exhaust.
Good points for sure. I'm going to think about this a bit more before I move on it.
WeeYariGeorgetown, Ontario, Canada · Nov 11, 2018#383
Originally Posted by tmontague ↑
The exhaust shop i went to also welded everything solid. Personally I'm not a fan. The gaskets with spring bolts add a section where it can flex under stress. This is one of the reasons my muffler weld snapped after 3 years when I was at the track.

I also like to be able to remove the exhaust in pieces if I need to service anything. I hate not being able to do thatvwithba solid one piece exhaust.
^ all of this.

I am currently welded solid as a repair was done which unbeknownst to me involved cutting out the flange. I hate the solid setup. I had been in the habit of swapping in my Tanabe Medalion for the summers, but no longer can. Now it just hangs useless in my basement.

Your hands just become tied once welded in.

Sent from my EML-L09 using Tapatalk
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 11, 2018#384
Exhaust Straight Talk...

Well, looking for opinions.

Here is my current setup:

Eastern Catalytics Midpipe which is large diameter until the resonator, then narrows down. This currently attached to the OEM Yaris, very restrictive, muffler. Question to you all: If I just bolt the Megan racing to the Eastern Catalytic midpipe, will it provide good enough flow. If I am only going to gain an almost imperceptible amount of power, does it really make sense to replace from the resonator back with large diameter pipe? I mean if I'm not going to feel a difference, is it really worth it. Maybe it would make a big difference. I also don't want cause the engine problems - in the long term - with too much backpressure. I suppose I could do this and then down the road, upsize that section of pipe.

Thought and opinions appreciated.

Picture not included in this copy
ArmstrongRacingSan Diego · Nov 11, 2018#385
I honestly wouldn’t mess with it yet. You’re still using a stock exhaust manifold so that pipe diameter reduction after the resonator likely isn’t your biggest issue.

I’d say just bolt it all up and drive it for a while. Try to sell off your 1nz parts and recoup some money, then revisit this in the future.
CrankyOldManWest Michigan · Nov 11, 2018#386
Originally Posted by 06YarisRS ↑
Excellent. Thanks Tom. Shall we order all 6? I would like to cover 1/2 of the cost. I can go ahead and place the order. We just need to decide where to send them.

Adam
I'm in. Domestic post in the us is pretty cheap, so I'm good with one person distributing them instead of separates shipping from the UK.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 11, 2018#387
Originally Posted by ArmstrongRacing ↑
I honestly wouldn’t mess with it yet. You’re still using a stock exhaust manifold so that pipe diameter reduction after the resonator likely isn’t your biggest issue.

I’d say just bolt it all up and drive it for a while. Try to sell off your 1nz parts and recoup some money, then revisit this in the future.
Excellent advice that I will follow, for sure. Thanks!
tmontagueCaledonia Ont. · Nov 11, 2018#388
Originally Posted by ArmstrongRacing ↑
I honestly wouldn’t mess with it yet. You’re still using a stock exhaust manifold so that pipe diameter reduction after the resonator likely isn’t your biggest issue.

I’d say just bolt it all up and drive it for a while. Try to sell off your 1nz parts and recoup some money, then revisit this in the future.
Fully agree, it wont make a large difference and since you tend to like to keep the rpm's down this will keep the torque in that range.

As Tom said, revisit it down the road if need be
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 11, 2018#389
Originally Posted by CrankyOldMan ↑
I'm in. Domestic post in the us is pretty cheap, so I'm good with one person distributing them instead of separates shipping from the UK.
Great, Sam. Am I interpreting correctly from your response that I should have the seller send them to you and you would redistribute? If so, please PM me your address. I'm going to contact the seller of the badges and see if he will give us a deal on 3, unless anyone else decides they want one. I will place the order when I hear back from the seller.

Thanks
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 11, 2018#390
Originally Posted by tmontague ↑
Fully agree, it wont make a large difference and since you tend to like to keep the rpm's down this will keep the torque in that range.

As Tom said, revisit it down the road if need be
Yes, I was thinking that too. I suppose the true benefit of a freer flowing system comes into play when the engine is outputting at higher RPM. Thanks.
DarkShadowFoxMassachusetts · Nov 11, 2018#391
Can you make one for the 2015 liftback because i am poverty :D ?
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 11, 2018#392
Exhaust Pipe Sizing

Thought I'd do a little reading about proper sizing for exhaust. For now I am just going to leave the 1.75" midpipe (from the resonator to muffler flange) and bolt up the Megan axleback. However, at some point down the road, I'll likely do an upgrade on that section of the midpipe.

Here is a table for reference. I am not sure how accurate this is, but it talks about flow through a "straight" section of pipe. According to the table (based upon a HP output of ~130), I should use a 2" pipe. I think The Barber said he had great success with a 2" resonator to muffler flange upgrade. Considering that I have the 1.8L engine and there are bends, turns etc in the pipe, I would upsize to 2.25", which jives completely with what everyone here is saying.

Link: http://www.exhaustvideos.com/faq/how...pipe-diameter/

Picture not included in this copy
CrankyOldManWest Michigan · Nov 12, 2018#393
Originally Posted by 06YarisRS ↑
Great, Sam. Am I interpreting correctly from your response that I should have the seller send them to you and you would redistribute? If so, please PM me your address. I'm going to contact the seller of the badges and see if he will give us a deal on 3, unless anyone else decides they want one. I will place the order when I hear back from the seller.

Thanks
If it's easier that way, I can do that. I was suggesting in general that it's probably easier on the seller to just use one address and then we as a group can sort it out on our end. =)
ern-dizCA all day · Nov 12, 2018#394
Originally Posted by 06YarisRS ↑
Picture not included in this copy
Hate to break up the good exhaust piping progress happening but I just saw this and had to acknowledge its excellence lol.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 12, 2018#395
Originally Posted by CrankyOldMan ↑
If it's easier that way, I can do that. I was suggesting in general that it's probably easier on the seller to just use one address and then we as a group can sort it out on our end. =)
As per PM, I had them sent to me, Sam. Not sure when they'll arrive, but I'll let you guys know approximately when to expect them. Thanks!
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 12, 2018#396
Originally Posted by ern-diz ↑
Hate to break up the good exhaust piping progress happening but I just saw this and had to acknowledge its excellence lol.
Like that do ya? 😆 Clearly, I have too much time on my hands. If I still had Photoshop, it would have been a better job. But Paint will do in a pinch.
ArmstrongRacingSan Diego · Nov 12, 2018#397
Originally Posted by 06YarisRS ↑
Like that do ya? 😆 Clearly, I have too much time on my hands. If I still had Photoshop, it would have been a better job. But Paint will do in a pinch.
Make that your profile pic!!!
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 13, 2018#398
Originally Posted by ArmstrongRacing ↑
Make that your profile pic!!!
Now there's an idea! 😆
ArmstrongRacingSan Diego · Nov 13, 2018#399
I had this wild idea that we should all take similar photos with our cars for TS group photo I can edit together. We just need to decide on a pose
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 13, 2018#400
Originally Posted by ArmstrongRacing ↑
I had this wild idea that we should all take similar photos with our cars for TS group photo I can edit together. We just need to decide on a pose
100% behind this!!! Would be awesome. 👍

As an aside, the badges have been processed through Heathrow.

EDIT: After watching your videos, Tom, I think one - complete with tunes - is in order for the TS group. 🤘 Maybe we should send you clips too!