Yarisworld Archive

06YarisRS's 2ZR-FE Swap 5-Door Hatchback (Automatic Transmission)

448 posts · 301,527 views · page 6 of 9

Replies continued

06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 31, 2018#251
Hey, thanks Adam. Not sure what it all means. Could it possibly mean that if I reconnected the blue wire, that my troubles would disappear? Probably wishful thinking. Haha
atomic_hojiKincardine, ON, Canada · Oct 31, 2018#252
lol - yes, I think you need to re-connect your blue wire; at least from what I see on the wiring diagram and that connector picture. Tom or Trevor may have a different reason as to why one of the wires on the autobox is grounded though - the autobox isn't my forte.. MT has a 2-pin connector for reverse indication. lol 😉

-- Adam
ArmstrongRacingSan Diego · Oct 31, 2018#253
[QUOTE=06YarisRS;818414]
Picture not included in this copy

Ok, I see what happened here, When I did my swap I thought I was clear that I used all COROLLA parts. So my corolla plug has no pin 10, just the 9 that I have been telling everyone.

Now because you have an xD harness the wires are different there at C29, You need to reconnect the blue wire.

Sorry for the confusion, I have no idea whats up with Brushhforhires swap and if he ever figured out this before the crash.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 31, 2018#254
Hi Adam and Tom.

I reconnected the blue wire to the harness and unfortunately I still have the P2770 code appearing.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 31, 2018#255
[QUOTE=ArmstrongRacing;818421]
Originally Posted by 06YarisRS ↑
Picture not included in this copy

Ok, I see what happened here, When I did my swap I thought I was clear that I used all COROLLA parts. So my corolla plug has no pin 10, just the 9 that I have been telling everyone.

Now because you have an xD harness the wires are different there at C29, You need to reconnect the blue wire.

Sorry for the confusion, I have no idea whats up with Brushhforhires swap and if he ever figured out this before the crash.
Thanks Tom. You were definitely clear about using Corolla only parts. It's my misinterpretation or failure to follow directions I suspect. I'm not giving up hope and really appreciate all the help, but I am beginning to wonder if I should have undertaken this project in the first place. I'm willing to do whatever it takes to fix this, but it may be too far beyond my skill level.
atomic_hojiKincardine, ON, Canada · Oct 31, 2018#256
Originally Posted by 06YarisRS ↑
Hi Adam and Tom.
I reconnected the blue wire to the harness and unfortunately I still have the P2770 code appearing.
May sound silly, but did you remember to clear all the codes? My recollection is that some OBD2 codes will stick the MIL/CEL on even if the condition no longer exists..

And is this the only code you're getting now?

-- Adam
CrankyOldManWest Michigan · Oct 31, 2018#257
Originally Posted by 06YarisRS ↑
I'm not giving up hope and really appreciate all the help, but I am beginning to wonder if I should have undertaken this project in the first place. I'm willing to do whatever it takes to fix this, but it may be too far beyond my skill level.
No way man, you've got this! You've already done all the hard work, why stop now? If you've still got access to the EWDs, go over them again and double check what wires go where.

1 attachment not included in this copy

ArmstrongRacingSan Diego · Oct 31, 2018#258
If clearing the codes does nothing, ground the brown wire next to the blue one you just fixed. That’s pin 9
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 31, 2018#259
Originally Posted by atomic_hoji ↑
May sound silly, but did you remember to clear all the codes? My recollection is that some OBD2 codes will stick the MIL/CEL on even if the condition no longer exists..

And is this the only code you're getting now?

-- Adam
Hey Adam. Yes, it's the only code I'm getting now. I was also getting a P0977 (shift solenoid "B" control circuit high), but that seems to have gone away by itself but that happened before re-connecting the blue wire. I have cleared the code with Torque Pro and it turns the MIL off, but it comes back on basically as soon as I turn the ingition on. I'm wondering if the speed sensor harness I made is having anything to do with this. I'm sure my wiring was right and the pins all went in nicely. Also, the CA2 connector is properly seated.

The MAf codes are all gone, but I've only run the car for 5 - 8 minutes at a time. My ac compressor does not sound good and no one had any PAG oil around here.

I thought that maybe the other DTCs were being set by low voltage due to my no-charge situation (which remains btw) but I've connected it to my van's battery. My multi meter shows 13.8 volts with the battery jumpered, but as soon as I take off the battery cable, it drops to 10ish volts and then keeps dropping.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 31, 2018#260
Originally Posted by ArmstrongRacing ↑
If clearing the codes does nothing, ground the brown wire next to the blue one you just fixed. That’s pin 9
I will definitely try that Tom. Thank you.
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 31, 2018#261
Originally Posted by CrankyOldMan ↑
No way man, you've got this! You've already done all the hard work, why stop now? If you've still got access to the EWDs, go over them again and double check what wires go where.
Haha, thanks Sam! I think I'm just a little tired now and a little disheartened. I've had quite a few consecutive late nights working on this project. I guess I'm wondering if some combination of parts/factors will make this project not possible. If I know that it definitely can be done (aka, it's possible electrically/mechanically and they there are no limitiations - other than my own, LOL - that make it impossible), then I'd feel better. I just don't know enough to know this for sure. It will probably turn out to be something that I missed and I'll slap myself for being stupid or careless. LOL. I do very much appreciate the encouragement.
tmontagueCaledonia Ont. · Oct 31, 2018#262
I rechecked Brishforhire's thread and your grounded wire is the exact same as his. Not sure about why the ewd's show it should be connected.

Have you checked if your ground is good? That's the first thing to do and then check your wiring on your ground is good


I'm not great with ewd's and I can't help much for the a/t swap other then what is in other threads
atomic_hojiKincardine, ON, Canada · Oct 31, 2018#263
Down to 1 OBD code is good progress! I've had mine on the road for months and there's at least 1 or 2 at any given time... 🙄

So I had a look in my 2018 Yaris manual, but the P2770 DTC (code) isn't actually listed - I either didn't download it, which is possible, or it isn't in this service manual.. The manual you had/have access to may have something in it though? Check in the auto transmission section of the manual(s) under the troubleshooting or control sections, maybe it will give you some more information. Maybe Tom knows more as he's more familiar with the automatics, but I think the SLU solenoid might be for torque converter lock-up? In which case, given the code you're getting, I think you're chasing the right rabbit hole... 😁

I did have a peek through the manual though and it looks like on the transmission itself there is a sub-harness from the connector that runs to the shift solenoids and components on the transmission. Might be worth having a check of those connectors that the wires are good - didn't get snagged on anything moving the 1NZ out / 2ZR in, connectors are clean and seated well. It's easy to do quick - ok, maybe not 'easy' since it's in the car..

Another idea would be to disconnect the battery, disconnect the engine harness connector at the ECM and the connector C29 at the automatic transmission and do a continuity / resistance check. So, basically get a multi-meter and stick a probe in the ECM pin and the other in the corresponding C29 pin and do a. a continuity check (a connection, multi-meter usually beeps) and b. a resistance measurement to see if you have high resistance in the wire - if you do, there might be a bad solder/connection. Work your way through all 9 wires and confirm your electrical connection is solid. It's a bit tedious, but maybe worth a look if the other ideas don't solve your problem.

A/C compressor hopefully survives, but sounds like it might need oil if you hadn't added any. A Ideal Supply / NAPA or similar should be able to order a small container of PAG for you. I recall it not being cheap given the tiny size of the container.. lol

Is it your Yaris' battery that's low? I might be mis-understanding, but if you jumper it from the van and it seems to charge with a good voltage, but you remove the good battery out of the loop and it drops, that seems like the Yaris' battery is hooped.. ?

Keep at it buddy, you're almost there... that first drive out you'll be cautious, listen for problems, nervous... then you'll get comfortable and open it up - and that's when the smiles start. 👍

-- Adam
ArmstrongRacingSan Diego · Oct 31, 2018#264
Originally Posted by tmontague ↑
I rechecked Brishforhire's thread and your grounded wire is the exact same as his. Not sure about why the ewd's show it should be connected.
Brushforhire's wiring was obviously wrong, not sure why he never disclosed that. He was the first 2zr + auto swap to use the xD auto harness. I've had Pin 9 posted in all of my write-ups and I don't understand why he did Pin 10 and never mentioned an issue.

I guess we will find out
06YarisRSThread starterFredericton, New Brunswick, Canada · Oct 31, 2018#265
You guys are amazing! I looked at the wiring diagrams again and SLU - (pin 9), as mentioned by Tom will get grounded tomorrow. P2770 refers to "An open in the shift solenoid valve SL circuit is detected". To me pin 9 is SLU - (or ground), so this makes sense that if not grounded, there would be an open circuit, thus setting the code. Feel free to tell me I'm full of it, LOL! I will report back tomorrow as to how this works. I am optimistic about this. I do have one question, though. Are these circuits protected, in other words, will damage be prevented by the ecu or does one run a risk of frying/damaging something by changing wires around?
ArmstrongRacingSan Diego · Oct 31, 2018#266
Originally Posted by 06YarisRS ↑
... will damage be prevented by the ecu or does one run a risk of frying/damaging something by changing wires around?
No, grounding the plug wires wont cause damage. However, if you were to ground the wire in the harness from the ECM on the positive side of the solenoid something bad may happen. That would be a direct short to ground!
tmontagueCaledonia Ont. · Nov 1, 2018#267
Originally Posted by ArmstrongRacing ↑
Brushforhire's wiring was obviously wrong, not sure why he never disclosed that. He was the first 2zr + auto swap to use the xD auto harness. I've had Pin 9 posted in all of my write-ups and I don't understand why he did Pin 10 and never mentioned an issue.

I guess we will find out
Well then, that makes more sense. I assumed his thread was all correct and never had time to look through any others
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 1, 2018#268
Originally Posted by atomic_hoji ↑
Down to 1 OBD code is good progress! I've had mine on the road for months and there's at least 1 or 2 at any given time... 🙄

So I had a look in my 2018 Yaris manual, but the P2770 DTC (code) isn't actually listed - I either didn't download it, which is possible, or it isn't in this service manual.. The manual you had/have access to may have something in it though? Check in the auto transmission section of the manual(s) under the troubleshooting or control sections, maybe it will give you some more information. Maybe Tom knows more as he's more familiar with the automatics, but I think the SLU solenoid might be for torque converter lock-up? In which case, given the code you're getting, I think you're chasing the right rabbit hole... 😁

I did have a peek through the manual though and it looks like on the transmission itself there is a sub-harness from the connector that runs to the shift solenoids and components on the transmission. Might be worth having a check of those connectors that the wires are good - didn't get snagged on anything moving the 1NZ out / 2ZR in, connectors are clean and seated well. It's easy to do quick - ok, maybe not 'easy' since it's in the car..

Another idea would be to disconnect the battery, disconnect the engine harness connector at the ECM and the connector C29 at the automatic transmission and do a continuity / resistance check. So, basically get a multi-meter and stick a probe in the ECM pin and the other in the corresponding C29 pin and do a. a continuity check (a connection, multi-meter usually beeps) and b. a resistance measurement to see if you have high resistance in the wire - if you do, there might be a bad solder/connection. Work your way through all 9 wires and confirm your electrical connection is solid. It's a bit tedious, but maybe worth a look if the other ideas don't solve your problem.

A/C compressor hopefully survives, but sounds like it might need oil if you hadn't added any. A Ideal Supply / NAPA or similar should be able to order a small container of PAG for you. I recall it not being cheap given the tiny size of the container.. lol

Is it your Yaris' battery that's low? I might be mis-understanding, but if you jumper it from the van and it seems to charge with a good voltage, but you remove the good battery out of the loop and it drops, that seems like the Yaris' battery is hooped.. ?

Keep at it buddy, you're almost there... that first drive out you'll be cautious, listen for problems, nervous... then you'll get comfortable and open it up - and that's when the smiles start. 👍

-- Adam
Thanks Adam. This sub harness you mention intrigues me. Here is a pic of the top trans plug. It seems to have mositure and dirt in it. Could this be causing a problem or are these pins completely isolated form eachother?

Picture not included in this copy
atomic_hojiKincardine, ON, Canada · Nov 1, 2018#269
^ could probably use a quick blast with some electrical cleaner, but the terminals themselves look decent from the picture; nothing corroded or mangled. Those terminals are pretty separate when the connector is pushed together, I wouldn't imagine it's causing a problem, but easy enough to give it a quick clean-up.

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 1, 2018#270
Originally Posted by atomic_hoji ↑
^ could probably use a quick blast with some electrical cleaner, but the terminals themselves look decent from the picture; nothing corroded or mangled. Those terminals are pretty separate when the connector is pushed together, I wouldn't imagine it's causing a problem, but easy enough to give it a quick clean-up.

-- Adam
Well that's good Adam. Thanks! I took my alternator in and had it tested. It passed with flying colors. I was actually hoping it would fail so I could just buy another, bolt it on be good to go. Haha. So it looks like I have another electrical problem to try to fix. A bit back in thread, Tom gave me some guidance that I will follow. I'll bolt the alternator back on, and try Tom's suggestion. I'll also ground the pin 9 wire and check to see if the P2770 goes away. If neither works, I think I may have to step away from this for a few days. The progress has been good so far - I'm really glad it started, lol - but I could use another 'win' soon. I need to convince myself that all obstacles are able to be overcome.

Here is the alternator print out

Picture not included in this copy

]
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 1, 2018#271
I reconnected the blue wire from pin #10 and grounded the brown wire from pin#9. I cleared the codes. As soon as I started the car, the P2770 returned. My connections are solid. I wondered if my battery was bad, so I put my van battery in and there was no difference.

Here is a pic that contains a snippet from the Yaris EWD I had from before and The scion xD diagram. Might this be helpful?

Picture not included in this copy
ArmstrongRacingSan Diego · Nov 2, 2018#272
I am lost here, I don’t understand how you are still having an issue.

Is the small 2 pin connector on top of the transmission plugged in?

You may need to check the wires to the AT plug with an Ohmmeter. Worst case scenario I can send you my harness that I know worked with no codes the whole time
tmontagueCaledonia Ont. · Nov 2, 2018#273
If all you connections are good then possibkena short in the harness. Like Tom said you can check for continuity down all the wire to make sure they are good
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 2, 2018#274
Originally Posted by ArmstrongRacing ↑
I am lost here, I don’t understand how you are still having an issue.

Is the small 2 pin connector on top of the transmission plugged in?

You may need to check the wires to the AT plug with an Ohmmeter. Worst case scenario I can send you my harness that I know worked with no codes the whole time
Thanks Tom! Yes, the 2 pin plug is plugged in. Yeah, I'm beginning to wonder if my harness is damaged. I think checking it with a multimeter is the approach now. So, I should stay with grounding the brown wire from pin 9? When you say to "check the wires to the AT plug", should I check this from the main plug at the ECU all the way to the trans plug or from CA2 in the underhood fusebox to teh trans plug? I apologize and I know that my limited understanding of electronics is contributing to this.

This link provides what appears to a good path to take:

https://www.obd-codes.com/p2770

Do you think that it is possible that the charging issue and my torque converter problem are related in any way?

I asked my helper yesterday if he noticed anything getting caught as we were pulling the 1NZ and putting the 2ZR in as he was on the transmission side and I was guiding the engines on the pulley side. He said that nothing got caught.

Finally, if my electrical tests don't show anything abnormal, would having Toyota use their special scan tool uncover the problem. I'd rather fix this at home but would have Toyota look at it if you think that they could find out what I've done wrong.


Thanks very much.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 2, 2018#275
Originally Posted by tmontague ↑
If all you connections are good then possibkena short in the harness. Like Tom said you can check for continuity down all the wire to make sure they are good
Thanks Trevor! It is indeed looking like this is the next approach to take. I'm wondering if one of these issues - the charging or the torque converter should be dealt with first.
tmontagueCaledonia Ont. · Nov 2, 2018#276
Almost always fix a charging system first. In modern vehicles low voltage can and will cause all sorts of weird things to happen.
ArmstrongRacingSan Diego · Nov 2, 2018#277
Originally Posted by 06YarisRS ↑

Picture not included in this copy
You will need to disconnect the large ECM plug and the AT plugand check resistance from end to end. Between:

S1: (B21)#79 - #5(C29)
S2, SLU, ST, SLT
Etc...
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 2, 2018#278
Originally Posted by tmontague ↑
Almost always fix a charging system first. In modern vehicles low voltage can and will cause all sorts of weird things to happen.
I think I will try to fix the charging issue first. Thanks Trevor.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 2, 2018#279
Originally Posted by ArmstrongRacing ↑
You will need to disconnect the large ECM plug and the AT plugand check resistance from end to end. Between:

S1: (B21)#79 - #5(C29)
S2, SLU, ST, SLT
Etc...
Thanks Tom. I will commence that testing shortly. I just need to see if the probes of my multimeter will reach, and make good contact with, the pins. I had meant to bring a paper clip from the school, but forgot.

I just have a quick question. You said that pins 1 and 2 of the alternator connector have to see battery voltage in order to get the alternator to charge, correct?

Picture not included in this copy

Right now my battery is at around 10 volts. As long as those pins see that voltage am I safe to assume that those wires are ok? I plan to put my battery on the charger tonight.

EDIT: Here are my voltage readings.

Battery Posts 10.2 V
With the ignition OFF:
Pin 1 10.2V
Pin 2 1.02V
Pin 3 0.66V
Pin 4 0.66V

With Ignition ON:
Pin 1 9.7V
Pin 2 9.7V
Pin 3 6.07V
Pin 4 8.33V

From alternator + post to battery -, I get 0 Volts

So, although it looks like I have continuity in all wires, and my alternator tested good, it will not start charging.

Oh, and I was remiss in not thanking you for the 'worst case' possible offer of the harness, but I would like to try fixing my issues. I would also have a hard time accepting that as I've already imposed upon you guys a lot.



Thanks!
atomic_hojiKincardine, ON, Canada · Nov 2, 2018#280
+1 on the charging problem as unreliable electrical source can cause all sorts of goofy stuff. Glad your alternator isn't hooped at least! 👍 Have you checked the charge cable connection at the alternator and the battery terminals? Checked the battery terminal connectors are good and tight? Good, clean connections everywhere from alt to battery, starter to battery, at battery to JB, etc.. and grounds! Poor connection from battery to body or from harness to engine block could cause a headache - granted, in saying that I would have imagined you'd have way more weird problems than just the 1 OBD code for the transmission solenoid.. 10V seems low to me, I would definitely throw it on a charger and see if it helps - can't hurt at least. lol

To check continuity and resistance I found that, as you mentioned, if you gently stick a sewing pin into the ECM terminal and carefully pull down on it while holding the multimeter probe on the sewing pin it pushes the sewing pin against the inside of the terminal and works a treat for measuring.

I admit, I'm a little confused why there's a need to ground any of the 10-pin connectors when they all run back to the ECM for control; in this case it's the SLU- signal, which is probably a ground provided by the ECM anyway... Quick Q, in case I missed it: are all 10-pins on your connector used? By the wiring diagram pin 7 should be blank - which seems to jive based on your picture of the male side connector that has no pin installed. If there's a wire at pin 7, is this connected to ground as a shielding / connector ground maybe?

Seems like if you're running the xD automatic ECM with an xD harness all the ECM side pins will jive. Checking the EWDs, all of those pins match the expected pins on the Yaris' 10-pin automatic transmission connector, so in terms of correct wire to correct function I think you're alright. Just need to resolve this weird circuit issue.

Keep us posted how you make out. You're almost there man! 👍
-- Adam
tmontagueCaledonia Ont. · Nov 2, 2018#281
Hiw reliable is the alternator test? I dont encourage throwing parts at the wall and seeing what sticks but 10v I silly low and could be a voltage regulator.

My alternator recently went and it would charge but only at 11v under load and 12.6 at idle. Over 3 weeks the car would lose more and more power until it turned over slow and eventually failed to start.

I got a free warranty battery as CT put it on their tester and said it was a bad battery. Same issue with second one until i tested the alt and found that as the source of the problen
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 2, 2018#282
Adam and Trevor. I'm responding to both of your posts here. First off, thanks for sticking with me as I muddle my way through this! I'm not sure if I should be happy about what I'm about to post, but, I will say that it does eliminate one potential issue.

First, the 10 volts on my battery is a result of sitting for a long time, plus running the car without charge. My alternator produced in a very heathy 14.XX volts and a peak of 15V on the bench test. I posted the printout a few posts back.

I have conducted the continuity tests from C19 - C29 using a straight pin for C19 and the other multimeter lead for C29. I had no problems establishing immediate connections and the results are... continuity in all wires! I tested each not twice, but 3 times. I said above that I'm not sure if I should be happy about this because it really makes me constantly wonder if there is some innate incompatibility in my car (Maybe a Canadian Yaris hatchback has different wiring than the other cars that got swapped). That said, I am feeling a little better. I enjoyed this testing, but had hoped I'd find a wire without continuity, then I coud start looking for the break in the harness.

I am really trying hard to get my head around the wiring diagrams and I have taken out another 2 day TIS membership.

I had hoped that issues would be resolved when I put my van battery (known good) in, but that made no diffrence.

Anyway, not really sure what to do next. But, like I said, I'm at least feeling a bit better today about the whole thing.

EDIT: I wanted to add that the xD harness has one wire coming off the negative battery terminal, where as teh Yaris had two, one of which bolted to the strut tower. May terminals are very clean and tight.

Also, Adam, pin 7 is vacant in both the male and female connectors of C29.

WAIT... I just thought of something... Back in a bit!

Picture not included in this copy
ArmstrongRacingSan Diego · Nov 2, 2018#283
Originally Posted by 06YarisRS ↑
Here are my voltage readings.

Battery Posts 10.2 V
With the ignition OFF:
Pin 1 10.2V
Pin 2 1.02V
Pin 3 0.66V
Pin 4 0.66V

With Ignition ON:
Pin 1 9.7V
Pin 2 9.7V
Pin 3 6.07V
Pin 4 8.33V

From alternator + post to battery -, I get 0 Volts

So, although it looks like I have continuity in all wires, and my alternator tested good, it will not start charging.

Oh, and I was remiss in not thanking you for the 'worst case' possible offer of the harness, but I would like to try fixing my issues. I would also have a hard time accepting that as I've already imposed upon you guys a lot.
The voltage at the alternator plug are perfect. However, you should always have battery voltage on the alternator positive post.

CHECK THE FUSES IN THE POSITIVE BATTERY POST

No worries about my harness, I only have 1 race left this year. Plus I need to start on my custom Mil-spec harness and stop procrastinating haha
atomic_hojiKincardine, ON, Canada · Nov 2, 2018#284
I went to reply, then went to check the alternator diagram to make sure I was right (then put the little one to bed), and Tom nailed it... lol

Fuse / Fusible Link. I recalled that you said you'd tried the van battery, so that ruled out the battery - though it's a good idea to charge it. But like Tom said, you should always have battery voltage on the alternator post and pin 1 of the 4-pin alternator connector - with no voltage on the post the ALT fusible link is probably blown. A continuity check would confirm that as well.

edit: re - grounding points, I recall a cable from the negative to the body (up around the tower as you mentioned), but also down to the transmission on my Yaris. If you don't have a cable to the transmission or the block then the alternator wouldn't be grounded via the block and that could also cause you a problem... I think the age old "check the fuse" as Tom suggested will be the age old "d'oh" moment.. 😁

-- Adam
tmontagueCaledonia Ont. · Nov 2, 2018#285
Hold the phone batman! I'm about 99% sure that the xd harness I have contains 2 large gauge ground wires from the negative battery terminal. One that connects to the body and one that connects to the trans case.

Humor me and run your pin 9 to a known ground on the chassis like a body panel. Or hell ever quicker have you ever actually tested your trans case is grounded?

I dont remember reading you stating you checked your trans ground was actually grounded.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 2, 2018#286
Gents! Here is a pic of what I think is the fusible link. This came from the Yaris and I just bolted the positive terminal to it. My assumption was that I should use the battery connector that was left over from the Yaris. Maybe I shouldn't have. I tested each fuse by placing the leads on each side of each fuse. I have continuity.

Picture not included in this copy

Here is a pic of the current terminals. When I posted earlier that I would be back, it was to go out and double up the negative terminals as the Yaris negative terminal connected to the strut tower and the transmission case. Trevor, you mentioned that you had another ground. My harness only appears to have the negative battery terminal. I'm thinking now I have a grounding (or lack thereof) issue. ANd I will perform the test - grounding wire 9 to a known good ground.


Picture not included in this copy



EDIT: Hang on... Is the fusible link on the body harness? I just had a look at my "Locations A&B" schematic and it refers to connector A28 and A29.

Picture not included in this copy
tmontagueCaledonia Ont. · Nov 2, 2018#287
Yes, using the fusible link plus battery terminal clamp from the yaris is correct and currently how mine is set up.

Look at the picture you just posted and notice how your yaris negative tab has 2 ground wires coming from it. Then look at your xd negative tab and notice that there is only one wire running from it.

Now go outside and test if your transmission case is grounded. This is something that you still have yet to report in but was mentioned to you pages ago. This will answer the question of what seems to be your issue to all of your problems.

In case you aren't sure how to do it just attach your positive probe from your multimeter to the battery positive and the negative probe to your transmission case and read the voltage. If you have no voltage then you have no ground. Or read resistance and you should have little to no resistance.

Then report back.

Typically when the fusible link is blown you have a hell of a lot if issues opp up and the dash can light up like a Christmas tree
ArmstrongRacingSan Diego · Nov 2, 2018#288
Originally Posted by 06YarisRS ↑
Picture not included in this copy

Looks good here


Picture not included in this copy
Cable #1 goes to the starter positive terminal.
Cable #2 goes to the alternator positive post, should be connected to the other attachment point on the front of this fuse block.
The left-over connection #3 in the back is your main ground point to the battery negative post, see how its grounded to the strut tower?
tmontagueCaledonia Ont. · Nov 2, 2018#289
I looked for a pic of my xd harness but cannot find one.

I'm pretty sure you have to use your yaris battery ground tab with the 2 wires from it (one to chassis and one to trans case)

The other ground tab from the xd harness I couldn't remember but Tom is likely correct that it goes to the fuse block, I just never remembered that part
atomic_hojiKincardine, ON, Canada · Nov 2, 2018#290
Well, good it's not a blown fuse/fusible link - that could indicate other problems either current or on the prior xD that hopefully wouldn't have damaged the wiring harness.

Those 2 connectors from the Yaris that you have labelled look like the 2 grounds - body and transmission that I recall. What I don't recall is any heavy gauge cable on an engine harness going to the negative terminal on the battery. Have you run that black cable (2) back to it's source... ?

For giggles, with everything sitting where it is now (battery out), check for continuity between the alternator terminal and that cable (2) - I'm wondering if you've been hooking the alternator up to the negative battery terminal instead of the side of the positive terminal block - which in the pictures you show is missing a connector.. which a quick look at my Yaris I think the red cable to the starter should be on the front of the block and the alternator - which has a black cable with a blue stripe on mine - should be to the backside of the positive terminal block.

edit: apparently while I ran to the garage the other guys already nailed it. 😆

-- Adam
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 2, 2018#291
You guys freakin rock! And I feel like an idiot!

14.6 Volts!!!! I will however put the battery on charge rather than expect the alternator to do that job.

I am going to sleep well tonight! Tomorrow I will do up the wiring on the trans plug. I still have the P2770 BUT I have neither wire grounded. Just so I'm clear, I should still ground brown wire#9, correct?

Soon it will be... except auto!
tmontagueCaledonia Ont. · Nov 2, 2018#292
EDIT* very sorry for the huge images, still learning how to use imgur, but at least these pics won't ghost in a couple weeks

Alright, in just spent some time looking st my old yaris harness and took a look in my engine bay and I'm pretty sure I know what your problem is.

The xd harness does not come with any large ground terminals that you hook up to your negative post on your battery. You keep your yaris ground cable for that

Picture not included in this copy

The xd harness comes with 2 large black wires with terminals and one will have red electrical tape on it and the other will not. These are both power cables that go to your positive terminal on the battery. The one with red tape is the direct line to the starter. They both attach to the two spots on the fusible link junction that you keep from your yaris.

Picture not included in this copy

I think your are either missing one of these positive cable ends or are attaching one to your negative side on the battery and/or not.using your yaris ground cables. Either way you need to test your trans case for ground.
tmontagueCaledonia Ont. · Nov 2, 2018#293
Originally Posted by tmontague ↑
I'd double check your ground on the trans. Use a multimeter or test light and make sure it is a good ground. If that's good then check the wiring.
Originally Posted by 06YarisRS ↑
You guys freakin rock! And I feel like an idiot!

14.6 Volts!!!! I will however put the battery on charge rather than expect the alternator to do that job.

I am going to sleep well tonight! Tomorrow I will do up the wiring on the trans plug. I still have the P2770 BUT I have neither wire grounded. Just so I'm clear, I should still ground brown wire#9, correct?

Soon it will be... except auto!
If you feel like an idiot it should only be due to not checking one of the simplest and earliest things mentioned to you when you first started the car - it would have saved yourself a lot of frustration and some of us a fair amount of time. You had to multimeter out and went to the trouble of testing wires in the harness all while neglecting to take the 10 seconds to check that the trans was grounded. Don't let that lesson go unlearned, it will help you when your wrench on cars in the future

Most of us were only able to do this swap because of the help of others, and I'm glad we were all able to help you out. Your trans code should clear once you connect and ground the proper wires. Definitely ground pin 9 that Tom mentioned, it is correct as per the ewd. Enjoy a weekend of hooning around a 2zr swapped Yaris!
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 2, 2018#294
It worked Trevor! I now have a grounded trans case and max charging! I still have the P2770 but I will fix that tomorrow, hopefully.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 2, 2018#295
Originally Posted by tmontague ↑
If you feel like an idiot it should only be due to not checking one of the simplest and earliest things mentioned to you when you first started the car - it would have saved yourself a lot of frustration and some of us a fair amount of time. You had to multimeter out and went to the trouble of testing wires in the harness all while neglecting to take the 10 seconds to check that the trans was grounded. Don't let that lesson go unlearned, it will help you when your wrench on cars in the future

Most of us were only able to do this swap because of the help of others, and I'm glad we were all able to help you out. Your trans code should clear once you connect and ground the proper wires. Definitely ground pin 9 that Tom mentioned, it is correct as per the ewd. Enjoy a weekend of hooning around a 2zr swapped Yaris!
Fair enough. I became hyper focused on extraneous aspects of the swap. Recall I said that I overthink things! LOL! EDIT: I did find your reference to checking the ground - post 244!

I do really appreciate all the help you guys have given me. Clearly, it wouldn't have happened without your help. I still have a decent list of things to do, including the A/C and exhaust. It's sounding like I'm going to have to replace my A/C compressor as I put the stethoscope on it and it's quite noisy - bearing I suspect.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 2, 2018#296
Originally Posted by ArmstrongRacing ↑
Cable #1 goes to the starter positive terminal.
Cable #2 goes to the alternator positive post, should be connected to the other attachment point on the front of this fuse block.
The left-over connection #3 in the back is your main ground point to the battery negative post, see how its grounded to the strut tower?
THANK YOU!!!
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 2, 2018#297
Originally Posted by atomic_hoji ↑
Well, good it's not a blown fuse/fusible link - that could indicate other problems either current or on the prior xD that hopefully wouldn't have damaged the wiring harness.

Those 2 connectors from the Yaris that you have labelled look like the 2 grounds - body and transmission that I recall. What I don't recall is any heavy gauge cable on an engine harness going to the negative terminal on the battery. Have you run that black cable (2) back to it's source... ?

For giggles, with everything sitting where it is now (battery out), check for continuity between the alternator terminal and that cable (2) - I'm wondering if you've been hooking the alternator up to the negative battery terminal instead of the side of the positive terminal block - which in the pictures you show is missing a connector.. which a quick look at my Yaris I think the red cable to the starter should be on the front of the block and the alternator - which has a black cable with a blue stripe on mine - should be to the backside of the positive terminal block.

edit: apparently while I ran to the garage the other guys already nailed it. 😆

-- Adam
Thanks very much, Adam!!!
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 3, 2018#298
Originally Posted by tmontague ↑
EDIT* very sorry for the huge images, still learning how to use imgur, but at least these pics won't ghost in a couple weeks

Alright, in just spent some time looking st my old yaris harness and took a look in my engine bay and I'm pretty sure I know what your problem is.

The xd harness does not come with any large ground terminals that you hook up to your negative post on your battery. You keep your yaris ground cable for that



The xd harness comes with 2 large black wires with terminals and one will have red electrical tape on it and the other will not. These are both power cables that go to your positive terminal on the battery. The one with red tape is the direct line to the starter. They both attach to the two spots on the fusible link junction that you keep from your yaris.



I think your are either missing one of these positive cable ends or are attaching one to your negative side on the battery and/or not.using your yaris ground cables. Either way you need to test your trans case for ground.
If you open your pics in Paint, Trevor, you can resize them before uploading them to imgur. 1024 x 768 or 800 x 600 are good resolutions for the forum. Thanks for the pics.
06YarisRSThread starterFredericton, New Brunswick, Canada · Nov 3, 2018#299
No codes after 10 minutes of running!!!

Remaining jobs:

- A/C compressor, o-ring replacement and recharge
- Axle back exhaust
- solder wiring connections
- secure coolant filler neck with bolts
atomic_hojiKincardine, ON, Canada · Nov 3, 2018#300
Originally Posted by tmontague ↑
...
Most of us were only able to do this swap because of the help of others, and I'm glad we were all able to help you out. ... Enjoy a weekend of hooning around a 2zr swapped Yaris!
^ This!

Glad you got it worked out man! 👍 As Trevor noted, find a quiet place and enjoy some honkin' on it; she goes, you smile - it's just the way it is. 😁

If that's the worst idiot moment you have, you're probably doing ok. lol Might feel silly, but nobody got hurt and nothing blew up; pride heals.. although sometime it takes a while to live a good 'whoops' down.

Keep us posted how you make out with the rest of your list, and congrats on the hard work and perseverance!

-- Adam