Replies continued
BEEFnorth carolina · Jul 21, 2012#301I am soooo chompin' at the bit over this one.
I just want to see it on the car and on the dyno (along with numbers).
the mock up you have with the intake and the flange looks good.
tooterThread starterLos Angeles · Jul 21, 2012#302I've been test fitting the prototype flange to the engine...
Picture not included in this copy
There are a couple of areas that need to be filed to fit because we went 3mm larger on the perimeter to accomodate the larger runners. There's one more spot to file near the middle of the fuel rail, so I should have it on today, and when the fitting is done I'll be sure to post some more pics. Wait till you see it with the runners on... it's gnarly. 🙂
tooterThread starterLos Angeles · Jul 21, 2012#303I just set on the runners to check the clearances... (goody 🙂)
Picture not included in this copy
Picture not included in this copy
Looks really neato. 🙂
anomoly40Central Arkansas · Jul 21, 2012#304You plan on wrapping them?
tooterThread starterLos Angeles · Jul 21, 2012#305Nope. 🙂
There are a lot of really nice options for finishing the manifold, and I'll be choosing one of them. In my opinion, wrapping looks crappy, so obviously I'm more concerned with looks than performance. 😉
goliath1812Ocala Florida · Jul 21, 2012#306looks good
BEEFnorth carolina · Jul 21, 2012#307that beats the crap out of the original plastic manifold (not a fan).
did you get the throttle body plate done yet?
tk-421Dagobah · Jul 21, 2012#308That's a rockin' setup! 🤘
Nice job.
tooterThread starterLos Angeles · Jul 21, 2012#309 Originally Posted by
BEEF ↑ that beats the crap out of the original plastic manifold (not a fan).
Yeah, it gets
lots of bling points even if it doesn't work. I'm doing this as much for that really cool Formula 1 look as much as for any of the other reasons. 😉
did you get the throttle body plate done yet?
Yes, it's done. I pick it up on Monday, and will post pics when I get it home. 🙂
I took the prototype flange and drilled and filed and Dremeled all of the peripheral clearances into it so that the new measurement data can be taken off of the corrected part and fed into the CNC machine for the finished version. 👍
BilliamUSA · Jul 21, 2012#310Not to be a party pooper...but haven't you basically voided your warranty on just about anything that would pop a CEL?
GolddeenohColumbia, SC · Jul 21, 2012#311if it pops a CEL then he puts his OEM parts back on, resets the ecu but disconnecting the battery, and goes on. as far as warranty, it is amazing what can be done to car with out voiding it and in general you can get away with a lot of simple mods for intake and exhaust it just depends on if they can prove that any problem that arises is a direct result of the mods applied.
tooterThread starterLos Angeles · Jul 21, 2012#312 Originally Posted by
Billiam ↑ Not to be a party pooper...but haven't basically voided your warranty on just about anything that would pop a CEL?
I'm a fuk warranty kind of guy... 🙂
...and am happy to assume all of the responsibilities of owning a new vehicle. I don't buy used vehicles either... always new ones. 👍
BilliamUSA · Jul 21, 2012#313 Originally Posted by
tooter ↑ I'm a fuk warranty kind of guy... 🙂
I can respect that. 👍
malibuguyWestminster, MD · Jul 21, 2012#314Looks flippin awesome on there!
anomoly40Central Arkansas · Jul 21, 2012#315Wait...that wasnt the final piece? Can i revise my numbers? Didnt know you were going to pull the old switcheroo... :)
tooterThread starterLos Angeles · Jul 21, 2012#316 Originally Posted by
anomoly40 ↑ Wait...that wasnt the final piece? Can i revise my numbers? Didnt know you were going to pull the old switcheroo... :)
Sure. 🙂
You can change your guess any time right up until I do the dyno run.
It would have been the final piece, but the flange had some fitment issues that needed refining so I resolved them today and the CNC guys will make a corrected part next week.
Picture not included in this copy mazillaSan Jacinto California · Jul 21, 2012#317Looks great! Are you going to bling it up with a polished fuel rail?
tooterThread starterLos Angeles · Jul 21, 2012#318I'm a linear one-step-at-a-time person, and only focus my attention on what needs to be done right now.
I'm still at #1. 🙂
1. Flange Fit.
2. Throttle Body Fit.
3. Weld.
4. Blast.
5. Clean.
6. Dyno.
BilliamUSA · Jul 22, 2012#3191 million HP. Picture not included in this copy
mazillaSan Jacinto California · Jul 22, 2012#320 Originally Posted by
tooter ↑ I'm a linear one-step-at-a-time person, and only focus my attention on what needs to be done right now.
I'm still at #1. 🙂
1. Flange Fit.
2. Throttle Body Fit.
3. Weld.
4. Blast.
5. Clean.
6. Dyno.
I get that, but I'd still put fuel rail in there somewhere so I didn't have to take all that stuff apart, maybe 5.5. 😁
cali yarisCanoga Park, CA · Jul 22, 2012#3215a. Drive
5b. Disconnect the battery to clear the CEL (after noting the error code)
5c. Repeat.
Just kidding, I am truly hoping those steps aren't included. 😆
CrankyOldManWest Michigan · Jul 22, 2012#322 Originally Posted by
tooter ↑ It would have been the final piece, but the flange had some fitment issues that needed refining so I resolved them today and the CNC guys will make a corrected part next week.
Was it the bolt hole alignment, or perimeter clearance?
tooterThread starterLos Angeles · Jul 22, 2012#323 Originally Posted by
cali yaris ↑ 5a. Drive
5b. Disconnect the battery to clear the CEL (after noting the error code)
5c. Repeat.
Just kidding, I am truly hoping those steps aren't included. 😆
I have no idea... this is all new to me. 🙂
You know far more about that than I do since you have years of experience with your manifolds and are a lot farther along in the process than I am. They certainly have to have been test run by now. Have any of your own short or longer runner manifolds triggered check engine lights? And if they did, how did you address them?
One decided advantage is that the throttle body and engine on either side of my manifold are in exactly the same bone stock condition as with the OEM manifold.
So with the manifold itself as the
only change I don't anticipate any issues. With no alteration of the size or profile of the actual entry and exit ports, utilizing all of the stock gasketing to insure a leak free design, and designing all of the adaptations to be smoothly transitioned, I'm optimistic that it will be just fine. 🙂
The check engine light issue would be greatly complicated if there were other concurrent changes being made. It would be much more difficult to address. This is why I'm focused just on making this
one mod and
nothing else. 👍
tooterThread starterLos Angeles · Jul 22, 2012#324 Originally Posted by
CrankyOldMan ↑ Was it the bolt hole alignment, or perimeter clearance?
It was perimeter clearances. The top of the flange needs to be milled down 1mm to clear the stock fuel rail supports. It's really close, as I was able to drop in the flange easily just by slightly loosening the fuel rail bolts. There is a cylindrical sensor close on the left side so I filed a semicircle to clear it. Also at the center of the fuel rail there's a part underneath it which also needed a semicircle filed to clear.
They were minor and corrected with a file. The goal is to make the flange simply drop in.
How are you doing on yours? I hope that sharing the details of the process will help to move your manifold along. 🙂
tooterThread starterLos Angeles · Jul 22, 2012#325 Originally Posted by
mazilla ↑ I get that, but I'd still put fuel rail in there somewhere so I didn't have to take all that stuff apart, maybe 5.5. 😁
I'm not going to make any other changes while working on this manifold. They would only complicate the process which I want to be as simple and direct as possible.
It's really easy to get in way over your head by making multiple changes at the same time, so I'm going to completely avoid that situation simply by not doing it. 😉
tooterThread starterLos Angeles · Jul 22, 2012#326 Originally Posted by
Billiam ↑ 1 million HP. Picture not included in this copy
The
1 is a good guess. 😆
CrankyOldManWest Michigan · Jul 22, 2012#327 Originally Posted by
tooter ↑ It was perimeter clearances.
Aah, I hadn't measured any of the surrounding areas, just guessed at the perimeter measurements.
How are you doing on yours? I hope that sharing the details of the process will help to move your manifold along. 🙂
Mine is pretty much shelved until I'm ready to do engine management--I'm not interested in fighting the ECU--but that will allow me to do cable throttle and a custom intake/exhaust setup. Then again, if your project works out as a net gain, I may just press on ahead with it.
cali yarisCanoga Park, CA · Jul 22, 2012#328Changing one thing at a time is a great strategy. There have been many times I wish I followed it, both on my cars and in my life. 😆
Flipper_1938Kentucky · Jul 22, 2012#329 Originally Posted by
cali yaris ↑ Changing one thing at a time is a great strategy. There have been many times I wish I followed it, both on my cars and in my life. 😆
That is an OK strategy for "almost stock" type builds.
If you go "full race" type build you gotta jump in with both feet.
tooterThread starterLos Angeles · Jul 22, 2012#330 Originally Posted by
CrankyOldMan ↑ Aah, I hadn't measured any of the surrounding areas, just guessed at the perimeter measurements.
I also guessed and used a simple hand file to fit. On the bottom and the right, there are no perimeter issues. At the top just left of dead center, and the right side near the flange mounting stud are the two areas.
Mine is pretty much shelved until I'm ready to do engine management--I'm not interested in fighting the ECU--but that will allow me to do cable throttle and a custom intake/exhaust setup. Then again, if your project works out as a net gain, I may just press on ahead with it.
Cable control is a completely different road which I'm not willing to travel. However, I'm happy to be the first manifold "lab rat", and will let you in on all the details. 🙂
cali yarisCanoga Park, CA · Jul 22, 2012#331 If you go "full race" type build you gotta jump in with both feet.
But after you do that build, it's still better to change one thing at a time,
when possible, or you'll never know what change made the difference, either way.
tooterThread starterLos Angeles · Jul 23, 2012#332Here's a pic of a gasket fit during the CNC of the throttle body adaptor... 🙂
Picture not included in this copy
These guys are artists!
cali yarisCanoga Park, CA · Jul 23, 2012#333I like it.
BEEFnorth carolina · Jul 23, 2012#334so.....time to head to the welder?
tooterThread starterLos Angeles · Jul 23, 2012#335No welder yet... 🙄
Today I go to the shop after work to return the flange that was hand filed to fit to the engine, so they can input the corrected dimension data and CNC another flange...
...then I go to the welder. 🙂
vtencolumbus · Jul 23, 2012#336Project is looking good tooter !
BEEFnorth carolina · Jul 23, 2012#337so they are going to mill you out another flange? are you paying for every time you use them or is it one fee? you could just used the filed one.
sorry, being impatient. I like this little project. regrardless of the gains, it is going to look mighty mean on the front of that engine.
tooterThread starterLos Angeles · Jul 23, 2012#338 Originally Posted by
BEEF ↑ ...sorry, being impatient.
That's ok... as long as I'm patient the project will turn out just fine. 🙂
tooterThread starterLos Angeles · Jul 23, 2012#339Here's the throttle body adapter...
Picture not included in this copy
The camera flash made the intake runners show up inside the manifold. I think this manifold has a distinct design advantage in that all 4 of intake ports of the runners are in direct line with the axis of the throttle body bore, like a backwards flowing exhaust header. 👍
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
It turned out beautifully... 👍
...and was quite a challenge for them to design a smooth transition from the 3 bolt manifold to the 4 stud throttle body without any of the 4 studs conflicting with the 3 hex bolts, while keeping the attitude of the rotationally sensitive gasket consistent with the throttle body's butterfly. 🙂
cali yarisCanoga Park, CA · Jul 23, 2012#340That is a PRETTY piece of work. I would make an extra one to have on my desk.
Can I sleep with it before you install it?
tooterThread starterLos Angeles · Jul 23, 2012#341 Originally Posted by
cali yaris ↑ That is a PRETTY piece of work.
Thanks, Garm... but I can't take any credit for it as I know absolutely
nothing about the manufacturing process. I only laid out the basic idea and let the guys decide how to implement a design in the best manner they saw fit.
I would make an extra one to have on my desk.
Can I sleep with it before you install it?
😆
vtencolumbus · Jul 23, 2012#342verry verry nice Tooter !! I think you should polished the whole thing from the manifold to the air intake ....industrial looks.
tooterThread starterLos Angeles · Jul 23, 2012#343Not sure what to do just yet. I might just have it glass beaded to a low metallic luster. The old manifold is really convoluted and has a lot of surface imperfections in it, and would be a real challenge to polish. 🙂
Jason@SportsCarDebary, FL · Jul 23, 2012#344Have it ceramic coated. Moving from the plastic to aluminum intake has the potential to raise your intake temp, coating it would help keep all the hot air from the rad from cooking it.
Lots of finish options:
http://www.jet-hot.com/ tk-421Dagobah · Jul 23, 2012#345 Originally Posted by
cali yaris ↑ Can I sleep with it before you install it?
I just had the worst mental image... Thank you for that! 👍
Picture not included in this copy ViperoniBrampton, ON · Jul 24, 2012#346Lookin good!
malibuguyWestminster, MD · Jul 24, 2012#347not to sound mean...but damn the flanges make the rest of the manifold look like crap
THEY ARE SEXY!!!
tooterThread starterLos Angeles · Jul 24, 2012#348 Originally Posted by
malibuguy ↑ not to sound mean...but damn the flanges make the rest of the manifold look like crap
THEY ARE SEXY!!!
I know... the machined parts are so stunningly beautiful it just makes the contrast to the old junkyard manifold look even worse. Glass beading should unify the surfaces. However, I may not glass bead the throttle body adaptor because it's so nice looking just the way it is.
cali yarisCanoga Park, CA · Jul 24, 2012#349Can we get a new summary on the whp/torque pool?
thanks 🙂
tooterThread starterLos Angeles · Jul 24, 2012#350Sure, Garm. 🙂
malibu +4 -6
Tooter +2 -3
Mazilla +1,000
Garm -5 -5
Anomaly +1 -3
Ljming -3 +3
BEEF +3 -2
Goldeenoh +5 -3
Goliath 0 0
tk-421 +4 -3
Billiam
Picture not included in this copy
+ 1,000,000