Yarisworld Archive

tooter's manifold adventure...

1,454 posts · 559,522 views · page 29 of 30

Replies continued

Bluevitz-rsOshawa, Ontario, Canada · Sep 5, 2013#1401
So it must be something you feel I the seat of your pants as you drive.
cali yarisCanoga Park, CA · Sep 5, 2013#1402
the intake manifold spacer lowered the torque peak by 2,500 rpm down to just 2,900 rpm.
With an LCE long tube header and this intake manifold spacer, the torque peak is reached at just 2,900 rpm
Is it the spacer alone or the header + the spacer? You've said two different things here. (I think I get the point, by the way).
GolddeenohColumbia, SC · Sep 5, 2013#1403
Originally Posted by cali yaris ↑
Is it the spacer alone or the header + the spacer? You've said two different things here. (I think I get the point, by the way).
it is magic :P
tooterThread starterLos Angeles · Sep 5, 2013#1404
Originally Posted by Bluevitz-rs ↑
So it must be something you feel I the seat of your pants as you drive.
Yes, and it drives just like the dyno chart results show. 🙂

Torque feels different from horsepower. Horsepower is the ability to gain rpms quickly, while torque is the ability to hold the same rpms while under a heavy load. Like the difference between acceleration and pull.

The truck pulls strongly at very low rpms. I use my truck as a fully loaded daily driver work vehicle, and am frequently in stop and go traffic. With a stick there's a lot of first gear clutching. On a level roadway I can slip the clutch from a standing start with no throttle and the truck moves smoothly with no bucking or dying out. I tested to see how low, and the breaking point of dying is if the rpms drop lower than 400-500 rpm which is below the idle speed. It runs like a tractor. 🙂
tooterThread starterLos Angeles · Sep 5, 2013#1405
Originally Posted by cali yaris ↑
Is it the spacer alone or the header + the spacer?
Ok. From the beginning... 😉

The first dyno run is with the header alone which lowered the peak torque from 3,800 rpms down to 3,150 rpms.

The second dyno run is with the addition of the spacer as the only change. It lowered the peak torque from 3,150 rpm down to 2,900 rpm.
tooterThread starterLos Angeles · Sep 5, 2013#1406
Originally Posted by Golddeenoh ↑
it is magic :P
Nope. It's just longer intake runners that obey all of the laws of physics 😉
cali yarisCanoga Park, CA · Sep 5, 2013#1407
You missed the point, Garm...
It doesn't make gains. It moves the torque curve lower in rpms.
I got it. The spacer lowered the peak torque by 250 rpm.
tooterThread starterLos Angeles · Sep 5, 2013#1408
Originally Posted by cali yaris ↑
I got it. The spacer lowered the peak torque by 250 rpm.
You got it, Garm. 🙂
And besides lowering the rpms of the absolute peak by 250... below that peak the tooter's torque curve is also fatter than the stock torque curve at other engine speeds, and it did it without giving up anything at the top end. 😉
tooterThread starterLos Angeles · Oct 6, 2013#1409
The first tooter II.VII production model has been machined... 🙂

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Here's a vid of a dyno run...

http://www.youtube.com/watch?v=H6ofUy8_-6Q

It's an extremely low rpm 4th gear pull starting to record at only 1,400rpm and up to redline at 5600rpm.

Here's how the truck sounds on the road in 2nd and 3rd gear, from 25mph to 70mph. All that sound you're hearing is coming just from the intake alone, as it's running the super quiet factory stock muffler. Had to suddenly cut the run short as I was headed into a canyon curve.

http://www.youtube.com/watch?v=UFTl75q49e4
tooterThread starterLos Angeles · Oct 6, 2013#1410
Finished the next tooter and put it on ebay. 🙂
Did a light polish job on the runners on this one...

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy
malibuguyWestminster, MD · Oct 6, 2013#1411
Nice work. I love your passion in this subject.

Ive been lazy and havent used my tooter flanges yet.
tooterThread starterLos Angeles · Oct 6, 2013#1412
You don't have to worry, Malibu... they won't spoil. 😉

I think my next project will be to develop an intake manifold spacer for our Yaris'. The truck spacers work really neato. 🙂

Hey, could you do me a big favor? I don't have any stock intake manifolds any more, so could you measure exactly how much clear space you have between the front of your stock intake manifold and the first thing it would touch if it was moved straight out from the head towards the front of your car? That will help me to determine how thick of a spacer I can make.

The thicker they are the better they work. 👍

Thanks,

Greg
malibuguyWestminster, MD · Oct 6, 2013#1413
2 7/8" from runner #4 to the fan shroud spoke on my sedan.
CTScottUSA, CT · Oct 6, 2013#1414
Right about the same for my liftback: 2-7/8" to 3"
tooterThread starterLos Angeles · Oct 6, 2013#1415
Hey, thanks guys! 🙂

That's great news... and means that a two inch spacer will work. The coiled stock intake runners are about 20 inches long if I recall correctly, so it would mean 10% longer runners. That's enough to make a noticeable difference. 👍

Greg
malibuguyWestminster, MD · Oct 7, 2013#1416
Going to make in plastic as well?
tooterThread starterLos Angeles · Oct 7, 2013#1417
Yes. Machining two inch deep aluminum caused tool issues. so they'll be made out of the same same nylon that the Yaris intake manifolds are made out of.

The spacer also straightens the flow before it enters the head...

Picture not included in this copy

Picture not included in this copy

My work truck is always loaded with about 600-800 pounds of material and tools, and I'm constantly crawling up and down steep roads in first gear so the spacer really helps in these off idle/very low rpm situations. Feels like you're driving a tractor. 🙂 It'll be interesting to find out how it will work on our Yaris'. When it's made, I'll do dyno runs and we'll see what happens. 👍

Greg
malibuguyWestminster, MD · Oct 7, 2013#1418
Try making one to run on a tooter as well...I dunno how much more room you can move the 'rolla intake out...but it may make magic or become a new doorstop...
Bluevitz-rsOshawa, Ontario, Canada · Oct 7, 2013#1419
A spacer will fit either manifold flange it's just a mater of clearance.
tooterThread starterLos Angeles · Oct 7, 2013#1420
Originally Posted by malibuguy ↑
Try making one to run on a tooter as well...I dunno how much more room you can move the 'rolla intake out...but it may make magic or become a new doorstop...
No can do... 🙁
The tooter's snaking runners already take up most of the front space. It's longer runners are already the equivalent of about a one inch spacer.

The Yaris spacer project will be a ways off just yet as I'm still focused on getting the Tacoma spacers produced and marketed, but it's definitely an intriguing idea worth pursuing. 🙂

I already know how well the principle of longer intake runners works on my truck because I'm driving it every day, so I'm sure that it will make a difference on the Yaris. What I don't know is exactly how much difference it will make...

...so that's what we'll find out. 👍

Greg
tooterThread starterLos Angeles · Oct 7, 2013#1421
Originally Posted by Bluevitz-rs ↑
A spacer will fit either manifold flange it's just a mater of clearance.
Yeah... not enough clearance. 🙁
But even if I'll never be able to use it,
it doesn't mean that others can't. 🙂

Greg
ViperoniBrampton, ON · Oct 7, 2013#1422
I'd love to see the spacer results on the Yaris :)
tooterThread starterLos Angeles · Oct 8, 2013#1423
Originally Posted by Viperoni ↑
I'd love to see the spacer results on the Yaris :)
So will I... 🙂

Can't wait to get started on it. I need to get the production run of tooter II.VII spacers finished first because there's already a list of people waiting to buy them. After the first run is completed I should be able to start on the Yaris spacer.

It's going to be called the

tooter I.V



( yipee... 🙂 )

...and another tooter manifold just sold on ebay. 🙂

Picture not included in this copy

Who knew? ...my hobby is actually starting to grow into a little business? 😉

Greg
ilikericesavannah, ga · Oct 8, 2013#1424
thats awesome. Congrats man. Been following this since day 1. I feel bad for those who are trying to read thru all 80 pages of this thread HAHA.

I know its still in production but whats a ballpark cost are we looking at for the intake mani spacer? Also, will you also provide extended studs or bolts or just give a part number to purchase on our own?
tooterThread starterLos Angeles · Oct 8, 2013#1425
Originally Posted by ilikerice ↑
thats awesome. Congrats man. Been following this since day 1. I feel bad for those who are trying to read thru all 80 pages of this thread HAHA.
There's a reason for putting everything into just one thread. It keeps this stuff from being spread all over the forum. That would be inappropriate. This way, none of the other threads get interfered with. 🙂

I know its still in production but whats a ballpark cost are we looking at for the intake mani spacer? Also, will you also provide extended studs or bolts or just give a part number to purchase on our own?
So far it's still only a concept. A prototype hasn't been designed or made, so there hasn't been any dyno testing to determine whether or not it's even worth producing. If it is made, it'll come as a complete kit including proper length studs, flange nuts, and a stock O ring gasket.

From how the R & D and production costs of the truck spacer have been piling up, it will likely be around $250.
tooterThread starterLos Angeles · Oct 13, 2013#1426
I discovered that stainless steel bead blasting aluminum creates a " micro shot peened" surface that polishes up really easy! 🙂

Picture not included in this copy

To get that lustrous finish in no time at all, I just hit the runners with some #400 sandpaper and then a little rubbing compound on a rag like polishing a silver spoon. 👍

There's also been a recent price adjustment. They're now $595 for the manifold and $295 for the kit.

Greg
cali yarisCanoga Park, CA · Oct 14, 2013#1427
What were the old prices?
tooterThread starterLos Angeles · Oct 14, 2013#1428
I started the manifolds really low at $450 and then gradually raised them so that I could come up to what the market would bear. Two have sold at $595, the last one from someone who saw my tooter YouTubes.

The internet is an amazing blessing... 🙂
It has allowed me as just one person to be able to personally control the total pipeline from concept, to design, to prototype, to testing, to manufacturing, to promotion, and to sales.

I don't have to answer to anyone else except the people who buy my products. The tooters are a very small market, and that was a good place to learn the process. The market for the tooter II.VII spacers is much larger, but I'm now more familiar with the process. On the Tacoma spacers, I was able to go from virtual concept to the reality of actual production for sales in just three months. This is because there are no third parties involved. I make all of the decisions myself, and I fund everything myself, and hire the good honest people who make it happen.👍

Greg
tooterThread starterLos Angeles · Oct 26, 2013#1429
The first production run of the tooter II.VII manifold spacers is done... 🙂

Picture not included in this copy

You can see how the spacer relocates the Tacoma intake manifold away from the engine...

Picture not included in this copy

My plan is to make an intake manifold spacer kit for our Yaris' because our intake manifolds are similar in design to the 2.7 Tacomas.

Picture not included in this copy



Greg
Bluevitz-rsOshawa, Ontario, Canada · Oct 26, 2013#1430
I remember from years past a similar product for the Honda crowd. They were marketed to keep the intake manifold colder and slow heat transfer from the head to the aluminum intake manifold.
tooterThread starterLos Angeles · Oct 27, 2013#1431
Originally Posted by Bluevitz-rs ↑
I remember from years past a similar product for the Honda crowd. They were marketed to keep the intake manifold colder and slow heat transfer from the head to the aluminum intake manifold.
With plastic manifolds, this is not a factor as the spacer is made out of the same material as the manifold. However, lengthening the intake runners does lower the torque peak making the engine pull stronger at lower rpms. Take another look...

Picture not included in this copy


Picture not included in this copy
Picture not included in this copy




The spacer also straightens the flow just before it enters the head. I'll have a prototype made, then dyno test it, and we'll see what happens. This won't be for a while just yet as I'm dealing with the sales of the tooter II.VII spacer right now. When that settles down, then I'll have time to focus on the tooter I.V. :)

Greg
Bluevitz-rsOshawa, Ontario, Canada · Oct 27, 2013#1432
I also remember throttle body spacers with a helical groove cut into them.
tooterThread starterLos Angeles · Oct 27, 2013#1433
Originally Posted by Bluevitz-rs ↑
I also remember throttle body spacers with a helical groove cut into them.
The difference is that at hrottle body spacer does not alter the flow dynamics of the intake manifold other then to very slightly enlarge the plenum area, whereas the intake manifold spacer does by actually making the intake runners physically longer.

People who design and build intake manifolds follow these two basic principles:

1. Longer intake manifold runners enhance low end torque

2. Shorter intake manifold runners enhance top end horsepower
WeeYariGeorgetown, Ontario, Canada · Oct 27, 2013#1434
You seriously need a synopsis thread. I've totally lost track of everything that has gone on in here, and don't much feel like skimming through 81 pages.

If you're serious on selling, I believe you could be missing out on a lot of newbies by not having a clean product offering thread.
Flipper_1938Kentucky · Oct 27, 2013#1435
Originally Posted by Bluevitz-rs ↑
I also remember throttle body spacers with a helical groove cut into them.
I was walking through pull-a-part yesterday and saw a "TORNADO"
tooterThread starterLos Angeles · Oct 27, 2013#1436
Originally Posted by WeeYari ↑
You seriously need a synopsis thread. I've totally lost track of everything that has gone on in here, and don't much feel like skimming through 81 pages.

If you're serious on selling, I believe you could be missing out on a lot of newbies by not having a clean product offering thread.
Hey Wee, 🙂

You're right, I'm not that serious because this is just a fun hobby. 😉

There's no Yaris intake manifold spacer to sell anyways because it hasn't been designed or machined or tested yet. So I don't even know if it will work good enough to offer for sale. The Tacoma spacer is for sale on another forum entirely.

The tooter manifolds and kits are all sold out and I've moved on to develop other products. 🙂


Greg
tooterThread starterLos Angeles · Nov 24, 2013#1437
The latest tooter went to a guy in Australia who has a '03 Echo with a three bolt cable operated throttle body. When I got another manifold off ebay to build the next one, it happened to come with a Corolla 51mm three bolt cable operated throttle body in excellent condition attached to it, and was priced exactly the same as if there was no throttle body...

Picture not included in this copy


So I sent it to him because there weren't any available there. Everything was s tight fit because of the smaller engine bay, but it all worked out fine. 🙂

Picture not included in this copy
bpt323Madison WI · Jan 9, 2014#1438
tooter...
after reading 81 pages as a guest. I have to say your work is impressive.

I've recently stumbled upon the corolla intake manifold which was introduced into my mazda community
(offtopic i know) but i think you'll enjoy seeing some more introduction of these manifolds in other uses
[see attached pictures] (not my car- but did produce 588whp/437ftlbs before bending the OEM rods)
throttle body is an unknown 80mm -far too large IMHO

Theres a good chance i'll be interested in some supplied parts:
the square machined flange to round transition & a tube w rounded end cap similar to that which you've used in the "tooter 2" design.

I'll PM you further.
Keep up the good work!

4 attachments not included in this copy

tooterThread starterLos Angeles · Jan 9, 2014#1439
Wow... 😲 Flipping it over! what a clever idea! Whoever made it did a really good job of it. Thanks so much for posting, man. 🙂 It's truly inspiring to see the creative ideas people come up with.

The CNC engineer will be back on the job next week machining parts, so I'll be starting another tooter build when they're ready.

Greg
malibuguyWestminster, MD · Jan 11, 2014#1440
I bought mine originally to use on my tercel in a similar fashion. Butn its going on the Yaris whenever I get around to it.
longlivekelKC Missouri · Mar 13, 2014#1441
Greg- I asked you via PM about the 2zz intake and you said the torque level was too high.
Well as discussed.. my tiny project car... The higher torque is great for traffic. Do you have a dyno sheet of the 2zz intake?
Thanks
tooterThread starterLos Angeles · Mar 14, 2014#1442
Originally Posted by longlivekel ↑
Greg- I asked you via PM about the 2zz intake and you said the torque level was too high.
Hi kel, 🙂

I had said that the 2ZZ intake runners were too short because it's a high revving engine. Short runners mean more high end horsepower... but less low end torque.

Well as discussed.. my tiny project car... The higher torque is great for traffic. Do you have a dyno sheet of the 2zz intake?
Thanks
Sorry, no... I only know that the longer the intake runners are, the more low end torque you'll get.


Greg
salmanghiyasPakistan · Jul 28, 2014#1443
Finally ... done reading 81 pages in almost 4 days
salmanghiyasPakistan · Jul 28, 2014#1444
HAIL tooter !!!!!
tooterThread starterLos Angeles · Jul 29, 2014#1445
Thanks fort he kind words, Salman. 🙂

You had asked in the PM about the exhaust, and it's basically stock except for a Weapon R header...

Picture not included in this copy

And a Magnaflow center exit exhaust from Micro Image. I'm not sure, but I don't think they're available any more.

Picture not included in this copy

Picture not included in this copy

A Tanabe Medalion Touring G is just as good, really deep ,mellow, and smooth... 👍

Picture not included in this copy

The rest of the exhaust is factory stock with all of the cats and resonators intact.

Greg
ezhacker1San Francisco · Jul 29, 2014#1446
Tomorrow, I'm installing the tooter i got from Kaotic after he sold his car. Quite hard to get a reliable mpg baseline the way i commute. But cant wait to feel some more torque sooner. :)
tooterThread starterLos Angeles · Jul 29, 2014#1447
While the change isn't huge, you can short shift easier without lugging the engine. 🙂

Greg
CrankyOldManWest Michigan · Jul 29, 2014#1448
Originally Posted by tooter ↑
While the change isn't huge, you can short shift easier without lugging the engine. 🙂

Greg
Or go forced induction. =P *bweeEEEEEEE*
salmanghiyasPakistan · Jul 30, 2014#1449
Thx tooter ...

Well i think it might not be relevent discussing here but still ... Just curious to ask ...

The weapon r headers outlet is 2" then u have the stock piping with 2 cats and 1 resonator .. the inlet of stock piping is 1.75" which joins the header outlet ... Then after the stock resonator pipe dia reduces to 1.25" ... Doesnt it loses the performance ?

Or any chance of air flow being effected ?
salmanghiyasPakistan · Jul 30, 2014#1450
Originally Posted by CrankyOldMan ↑
Or go forced induction. =P *bweeEEEEEEE*
Hey cranky ...

Im first planning to put every thing for the NA setup ... As we do not have enough resources here for forced induction ... And importing things become very expensive due to customs duty ... NA setup is not easy either i know .. but i can go 1 by 1 installing things in this ...

Here .. top NA's are ..

Honda civic 2002 - K24 ... Unbeaten till now ...

Honda civic 1995 - H22 type S .. 2nd

Then we have

Charade with B16 and suzuki Kie with G15

And so on ... My aim is to atleast RIP those B16 charade and kie G15 ... So that i wud become the 3rd in position ...

Just a silly dream of mine :$