tooterOriginal postLos Angeles · Jun 7, 2012#1The Corolla manifold came in yesterday... 🙂
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
At under 6.5 pounds, it's very lightweight for it's size. The runners are massive compared to the stock manifold. They're also extremely long which should enhance low end torque. It does have a small plenum with an intake tube behind the throttle body which extends far into it and directly in line with the runners...
Picture not included in this copy
The port for the throttlebody is slightly larger than 50mm which should easily accept the stock Yaris TB.
Picture not included in this copy
Picture not included in this copy
The manifold runners come really close to matching the intake ports of the engine...
Picture not included in this copy
Picture not included in this copy
Got that neato intake manifold temprature isolating gasket from Jeff. (thanks, man!) With it's accurate profile of intake and bolt hole layout, it will be really simple to have a thick aluminium plate made to match it.
This is going to look so freaking cool on the engine. 🙂
Replies 1,453
cali yarisCanoga Park, CA · Jun 7, 2012#2Subscribed! 🙂
tooterThread starterLos Angeles · Jun 7, 2012#3Deflanged the manifold with a Sawzall...
Picture not included in this copy
The two inner runners are fine. The inside edge of each outside runner doesn't match its respective intake port...
Picture not included in this copy
The misalignment only amounts to 5mm at its greatest point, so I don't believe that will be a problem. I'm thinking of a really thick flange so I can file it to create a smooth flowing transition between the head and the intake runners. The one I cut off was 18mm thick and had plenty of slack in it to compensate, so I'll likely go with one at least that thick.
CrankyOldManWest Michigan · Jun 7, 2012#4I was thinking of using a torch to heat and bend it a bit. Either that or removing the runners from the plenum entirely and making a new plenum from scratch.
tooterThread starterLos Angeles · Jun 7, 2012#5Nice ideas, Cranky... 🙂
...but I'm going to try to keep this project as simple as possible since it's a first attempt of a novice. The runners are pretty thin aluminium and would likely deform under heat and the pressure of trying to bend them. They're already so nicely mandrel bent by the factory, it would be a shame to risk ruining them. And I'll likely retain the original plenum as it's volume and configuration has already been flow engineered by Toyota to work harmoniously with the runners.
However, if you want to have a go at one, here's plenty of them around to experiment on with a minimal financial committment. 👍
cali yarisCanoga Park, CA · Jun 7, 2012#6The only way to know if this makes any power will be to dyno the car with and without the modification. Are you planning on doing that?
GolddeenohColumbia, SC · Jun 7, 2012#7we have a early 90's Corrola in Auto shop that has the same intake on it, when i saw it i thought about you getting this one.
CrankyOldManWest Michigan · Jun 7, 2012#8 Originally Posted by
tooter ↑ Nice ideas, Cranky...However, if you want to have a go at one, here's plenty of them around to experiment on with a minimal financial committment. 👍
Yup, got one in the shed somewhere...
tooterThread starterLos Angeles · Jun 7, 2012#9 Originally Posted by
cali yaris ↑ The only way to know if this makes any power will be to dyno the car with and without the modification. Are you planning on doing that?
Hey Garm, 🙂
Sorry, no plans for any red line balls to the walls dyno runs. The engine has only 600 miles on it and still breaking in. However, I am keeping meticulous gas mileage records to see if it will have any effect on economy.
I'm mainly doing this just because I think it will look really cool like your exhaust. 😉
tooterThread starterLos Angeles · Jun 7, 2012#10 Originally Posted by
CrankyOldMan ↑ Yup, got one in the shed somewhere...
It's there just waiting for you to see what you can do with it.
And I'll keep you posted step by step as to how this goes. 🙂
tooterThread starterLos Angeles · Jun 7, 2012#11 Originally Posted by
Golddeenoh ↑ we have a early 90's Corrola in Auto shop that has the same intake on it, when i saw it i thought about you getting this one.
There's zillions of them around... some of the best practical reliable cars Toyota ever built. I would have never even thought of this if I didn't see that the guys from Puerto Rico had already done it.
mazillaSan Jacinto California · Jun 7, 2012#12Tag
cali yarisCanoga Park, CA · Jun 7, 2012#13 I'm mainly doing this just because I think it will look really cool like your exhaust.
ha! At least you are clear about it. It's going to make more power, or less. That just about covers it.
Can we borrow it and dyno a test car when you're done? 😁
tooterThread starterLos Angeles · Jun 8, 2012#14 Originally Posted by
cali yaris ↑ ha! At least you are clear about it. It's going to make more power, or less. That just about covers it.
If it works and looks cool, I'm happy. 🙂
Can we borrow it and dyno a test car when you're done? 😁
No problem, Garm. 👍
I'm building two of them... 😉
Picture not included in this copy I think this design of long runners in direct alignment with the throttlebody is a really good one, or Toyota wouldn't have used it. The extremely long runners on my truck are also oriented in a similar manner and and it works swell.👍
Picture not included in this copy ilikericesavannah, ga · Jun 8, 2012#15Depending on the gain this will have, if proven alot, I may look into going F Street Prepared, lol
Looks awesome. hope this works out.
eTiMaGoBangkok, Thailand · Jun 8, 2012#16gently bang the outer runners with a rubber mallet? (and put something tight inside the runner so it does not actually deform)
WeeYariGeorgetown, Ontario, Canada · Jun 8, 2012#17 Originally Posted by
eTiMaGo ↑ gently bang the outer runners with a rubber mallet? (and put something tight inside the runner so it does not actually deform)
I was thinking that a pipe clamp could be used to gently draw the two outer runners in.
tooterThread starterLos Angeles · Jun 8, 2012#18Excellent ideas worth considering, guys! 👍
On the flaring idea. maybe just right at the end so that it would be covered up by the weld and wouldn't even show. Pulling the outer runners together might also work if I used two parallel pipes the exact diameter as the inside edge of the runners. 5mm on each isn't much. I might try putting just a little pressure on them to see exactly how much resistance there is. And maybe a combination of both... of just a bit of pulling and a touch of flaring.
It's really great that the slight misalignment issue the only thing close to an obstacle. The engine flange and adaptor plate for the throttle body are pretty academic. A thick throttle body plate will have 3 counter sunk recesses to accept short hex bolts which will attach it to the manifold, and then have 4 threaded holes for the stock throttle body studs. I should be getting the stock manifold soon which will be used for the pattern to keep everything oriented as close to their stock positions as possible.
tooterThread starterLos Angeles · Jun 8, 2012#19 Originally Posted by
ilikerice ↑ Depending on the gain this will have, if proven alot, I may look into going F Street Prepared, lol
Looks awesome. hope this works out.
It'll work all right... I just don't know how
well it will work. 😆
I think the gain if any at all will be slight... because the throttle body and the engine on each end of that manifold will still be exactly the same.
cali yarisCanoga Park, CA · Jun 8, 2012#20^ It is possible to speed up the air traveling through an opening fixed in size, if the previous manifold isn't optimized for air flow.
fnkngrvIn The Hotbox · Jun 8, 2012#21 Originally Posted by
cali yaris ↑ ^ It is possible to speed up the air traveling through an opening fixed in size, if the previous manifold isn't optimized for air flow.
Picture not included in this copy 😆😆😆
cali yarisCanoga Park, CA · Jun 8, 2012#22🤷
tooterThread starterLos Angeles · Jun 8, 2012#23 Originally Posted by
cali yaris ↑ ^ It is possible to speed up the air traveling through an opening fixed in size, if the previous manifold isn't optimized for air flow.
Yes. And I'm figuring that the air flow of the stock manifold is very well optimized for efficiency and driveability in the lower rpm ranges.
It would be difficult to beat that because once they start with computer simulations and molding plastic intakes it's perfectly feasible to form them into
any configuration without limitation.
Even though the Corolla manifold is made to supply an engine which is 20% larger than the Yaris, it's highly unlikely that it would flow any better under normal everyday driving conditions.
The only advantage I can see (besides it looking
really cool 😉 ) is the runners being in direct line with the axis of the throttle body.
It's strange how that tube extends straight out from behind the TB and into the plenum...
Picture not included in this copy It's 2 1/2 inches long and terminates 2 1/2 inches away from the runner intakes. There may be some harmonic flow principle behind making those two measurements equal, because you'd normally think they'd simply make the throttle body dump straight into the open plenum.
All this stuff positively fascinates me, and it's no end of fun to explore. 🙂
GolddeenohColumbia, SC · Jun 8, 2012#24I would get a drimal and clean up that corrosion^ maybe smooth it out a little.
fnkngrvIn The Hotbox · Jun 8, 2012#25 Originally Posted by
cali yaris ↑ 🤷
making fun of the couple companies out there that claim what they do about much better airflow with those tornado gadgets. 👍
cali yarisCanoga Park, CA · Jun 8, 2012#26oh yeah those things... lol
tooterThread starterLos Angeles · Jun 8, 2012#27 Originally Posted by
Golddeenoh ↑ I would get a drimal and clean up that corrosion^ maybe smooth it out a little.
The black is just accumulated layers of unburnt hydrocarbons that repeatedly got cooked over the many years of the manifold's life. I'll be spraying the whole insides with engine degreaser and hosing it out. Can't get inside there with a Dremel. The hole is way too small and the runners are too deep inside the plenum.
tooterThread starterLos Angeles · Jun 10, 2012#28Saw this pic of a thick custom made intake flange on the Micro forum...
Picture not included in this copy
I tried tapping with ball peen hammer on the inside of the runner to flare the opening with some success. But instead of risking denting or deforming the runners, a thick flange like this one with a few extra beads of weld on the misaligned areas will provide plenty of room to smooth the transition from the inside with a grinder between the runners and the engine intakes.
GolddeenohColumbia, SC · Jun 10, 2012#29^ I need one of those to go with my prius pistons :D
tooterThread starterLos Angeles · Jun 10, 2012#30That's beautiful for a scratch built manifold. It says: Go Fast.
While I'm still waiting to receive the stock manifold before the project can proceed, I did manage to clean up the insides of the manifold...
Picture not included in this copy
...with a combination of engine degreaser and brake cleaner. Just a personal peeve, I can't stand working with dirty parts.
tooterThread starterLos Angeles · Jun 11, 2012#31Just got the stock manifold today in absolutely pristine condition.
Thanks, 90tsi for selling me yours. 👍
Picture not included in this copy
Now there's an accurate frame of reference for clearances, throttle body stud spacing and such. Next up is a trip to the machine shop. 🙂
packetraceQuebec · Jun 11, 2012#32where did you took the corolla intake manifold ?
CrankyOldManWest Michigan · Jun 11, 2012#33 Originally Posted by
tooter ↑ Now there's an accurate frame of reference for clearances, throttle body stud spacing and such. Next up is a trip to the machine shop. 🙂
Would you be willing to share those numbers? I'd be happy to put them on to the CAD drawing and re-post it. Oh, I already have the throttle body template sketched. Now where did
that one go... Aah, there it is. The bolt pattern is identical to the 1.5L TB, but the bore is smaller (on the 1.5L).
1 attachment not included in this copy
tooterThread starterLos Angeles · Jun 11, 2012#34Bought it on Ebay. 🙂
They're pretty common as toyota used them for years on a couple different models.
Picture not included in this copy
tooterThread starterLos Angeles · Jun 12, 2012#35 Originally Posted by
CrankyOldMan ↑ Would you be willing to share those numbers? I'd be happy to put them on to the CAD drawing and re-post it. Oh, I already have the throttle body template sketched. Now where did that one go... Aah, there it is. The bolt pattern is identical to the 1.5L TB, but the bore is smaller (on the 1.5L).
Sure, Cranky... 🙂
Which measurements would you like?
Picture not included in this copy Picture not included in this copy Picture not included in this copy The Yaris manifold bore is 48mm whereas the Corolla is 50mm.
CrankyOldManWest Michigan · Jun 12, 2012#36Doh, I should have been more specific, eh? The bolt pattern for the head-side of the intake. I made some educated guesses on my CAD model, but haven't actually measured them.
poorsh2ne ct · Jun 12, 2012#37This intake mod may have a chance. good luck, may the car gods be with you
tooterThread starterLos Angeles · Jun 12, 2012#38 Originally Posted by
CrankyOldMan ↑ Doh, I should have been more specific, eh? The bolt pattern for the head-side of the intake. I made some educated guesses on my CAD model, but haven't actually measured them.
You got it. 🙂
When I get home from work this evening, I'll lay straight edges across the two rows of bolt holes and will be able to give you some x and y measurements.
tooterThread starterLos Angeles · Jun 13, 2012#39Hey Cranky, 🙂
Here's some of the measurements. They're not perfect but accurate to a millimeter because I just used a ruler.
Bolt holes on intake manifold to engine head connection
looking at the flange from the position of the bolt holes making a W.
The y distance between the two rows of bolt holes (not including the one hole that's offset) is 24mm.
The x distance between the two holes on either side of the center hole is 166mm.
The x distance from the center hole to the end hole which is in line with it is 163mm.
The y distance beween the one offset hole and the closest hole to it is 33mm.
The x distance between the center hole and the offset hole is 163mm.
Hope this helps. Let me know if you need any clarification. 🙂
CrankyOldManWest Michigan · Jun 13, 2012#40Interesting. Some of my estimations were spot on, and others were pretty far off. I used pictures of gaskets and the head to get a general idea of the location and then used a SWAG to pin them down.
For the y-distance, did you measure center-to-center or edge-to-edge? All of the images I found showed the bolt hole centers being approximately in line with the long edges of the intake holes, which should be 30mm tall.
tooterThread starterLos Angeles · Jun 13, 2012#41 Originally Posted by
CrankyOldMan ↑ Interesting. Some of my estimations were spot on, and others were pretty far off. I used pictures of gaskets and the head to get a general idea of the location and then used a SWAG to pin them down.
It's kind of tough to measure with the holes diagonal to each other and one offset from the others. I stenciled that white temprature insulating gasket I got from Garm onto a piece of paper and measured off of the paper with a ruler. Having a physical gasket made it much easier but they're far from the exact measurements a machinist would make.
For the y-distance, did you measure center-to-center or edge-to-edge? All of the images I found showed the bolt hole centers being approximately in line with the long edges of the intake holes, which should be 30mm tall.
All the hole location measurements were taken center to center, and I ignored the intake holes as drawing around them with a ball point pen automatically made them smaller.
I'm taking everything down to the machine shop today to get the flange and throttlebody adaptor made up. 🙂
Picture not included in this copy With the Corolla manifold, the stock Yaris manifold, the white intake gasket, and all of the bolts and studs right there in front of them to, it should be a simple job to fabricate the parts out of 25mm aluminium stock.👍
fnkngrvIn The Hotbox · Jun 13, 2012#42such a great little project. 🎉
tooterThread starterLos Angeles · Jun 13, 2012#43I just have to tell you guys about something that has nothing to do with our cars.
There is something so fascinating about the flow of events and how sometimes you find yourself in just the proper place in relation to them where you can surf them like a wave. Today was one of those times.
Took the parts to the guys I know who have the CNC machine. No problem! 👍 The flange will be 1 inch thick with a smooth transition machined right into it to flow smoothly from the Corolla manifold runners to the intake ports in the Yaris head. There's no need to try to adjust the runners! 😁
Now... this is what I didn't know. The guy who is creating the CAD file and running the CNC was a design engineer for the Ford Motor Company.
And what job did he do?
He designed INTAKE MANIFOLDS! 😲
When he saw the project he took a genuine personal interest in it. This is turned out to be a perfect synergy of events. To come into contact with just the right people at just the right time. Sometimes the way events unfold can be more fascinating than the events themselves.
The prototype manifold should be up and running in under 2 weeks.🙂
mazillaSan Jacinto California · Jun 13, 2012#44Whats the cost on the machine work, flange and TB adaptor?
This project is moving along nicely, well done...I'm excited to see how it turns out.
tooterThread starterLos Angeles · Jun 13, 2012#45Don't exactly know yet... just whatever the cost of the time and materials comes out to produce a couple sets. This guy is an honest man who will make a fair profit for his time and talents so I let him determine the price, and just said "Let's do it." 🙂
Trusting honest people who are trustworthy is a valuable commodity in this world... it's the invisible glue that holds the business world together.👍
mazillaSan Jacinto California · Jun 14, 2012#46 Originally Posted by
tooter ↑ Don't exactly know yet... just whatever the cost of the time and materials comes out to produce a couple sets. This guy is an honest man who will make a fair profit for his time and talents so I let him determine the price, and just said "Let's do it." 🙂
Trusting honest people who are trustworthy is a valuable commodity in this world... it's the invisible glue that holds the business world together.👍
Greed holds business together...greed and booze. 😉
tooterThread starterLos Angeles · Jun 14, 2012#47 Originally Posted by
mazilla ↑ Greed holds business together...greed and booze. 😉
There's nothing wrong with self interest where both parties financially benefit from freely choosing to enter into a business transaction.
Wealth is created.🙂🙂
In contrast to self interest is greed where one person's gain can only come from another's loss.
Wealth is transferred. 😛😢
malibuguyWestminster, MD · Jun 14, 2012#48I like this project. I have one of these intakes laying around...if this works out in terms of gains mark me down for a flange.
tooterThread starterLos Angeles · Jun 14, 2012#49You got it, malibu. 🙂
Documented gains is the catch in all of this.
I'm guessing the design should yield good torque numbers because of the length of the runners, and how they are directly in line with the axis of the throttle body. However the stock manifold runners, although much smaller in diameter, are also very long because they wrap almost all the way around the plenum. I really should have taken a picture of the underside and back of the manifold before leaving it at the machine shop so that you'd be able to see what's going on there for yourself. The stock manifold looks like a snail underneath.
However, I really like this particular design because it gets right around the whole plenum issue of trying to draw in air at a 90 degree angle to the flow from the throttle body.
It's highly possible that the manifold doesn't produce any gains at all. After the engine is completely broken in I think I'm going to need to do a dyno run with my car to get a baseline and then do one with the manifold to get a direct apples to apples comparison. This could all end up being just a useless piece of engine bling! 😆...
...but finding out is what life is all about. 🙂
tooterThread starterLos Angeles · Jun 14, 2012#50 Originally Posted by
poorsh2 ↑ This intake mod may have a chance. good luck, may the car gods be with you
Thanks for your good wishes, poor. 🙂
I'm a big fan of God and the natural physical laws He designed which govern the flow of events. So I keep an eye out for the signs with arrows on them that say "This Way", and have lots of fun following them just to see where they go.👍