so when this is all said and done.. whoever gets the blueprint, will someone sell just the flange by itself or start buying up old corolla manifolds and doing all the welding themselves and sell it as a whole?
tooter's manifold adventure...
1,454 posts · 559,522 views · page 2 of 30
Replies continued
That's still a wide open question because I've yet to find out if this will even work decently. 😕
Should have the first one completed and running in two weeks. I'm looking up the street and so far all the lights are green.🙂
Should have the first one completed and running in two weeks. I'm looking up the street and so far all the lights are green.🙂
I could do the service. There is alot of 1zz corollas in the yards around here and well i fabricate for a living. However welding that thin tubing to a 1" thick flange is going to be a trick...but ive pulled off some crazy stuff before!
I wish that you really were in Malibu... 🙁
Love this project. I think it would be easier to take the general idea and make them from scratch in production runs. The flange will be the same on each one and positioned correctly, for example, as opposed to making each one as an individual project. Would bring the cost down as well.
whoever gets the blueprint, will someone sell just the flange by itself or start buying up old corolla manifolds and doing all the welding themselves and sell it as a whole?Maybe! And to go back to Tooter's point about wealth, that is when wealth will be created, not before. So far, a fee has been paid for a service to add "value" to a part. Wealth is created only when the part is sold with the added value included (aka profit), not before.
I would possibly be interested in a finished product if it made power.
I understand what MI is saying about a mass produced piece and fitment. I think what tooter is doing is awesome for himself or as a DIY. I honestly just like the look of the metal intake manifold vs the plastic one.
if you do dyno before and after, I (and several others) would love to know the power delta with and without.
I understand what MI is saying about a mass produced piece and fitment. I think what tooter is doing is awesome for himself or as a DIY. I honestly just like the look of the metal intake manifold vs the plastic one.
if you do dyno before and after, I (and several others) would love to know the power delta with and without.
Hey Garm, :)Originally Posted by cali yaris ↑Love this project. I think it would be easier to take the general idea and make them from scratch in production runs.
When you say "make them from scratch", do you mean like buying tubing and getting it mandrel bent and building the throttle body base? Don't think I'm ready to go quite that far just yet! 😲
Remember, all this began with the idea to make just one manifold because I saw that the guy from Puerto Rico did it! 😆
The flange will be the same on each one and positioned correctly, for example, as opposed to making each one as an individual project. Would bring the cost down as well.Well, that's exactly what happened.😉
I went to my neighbor's big machine shop in town and showed him the project. He said that I'd do much better with a CNC machine. (I didn't realize that he didn't have one) He said that one of his machinists could make one flange, but it would take a day doing it from scratch on a mill and would cost about $1,000.
So I went to two guys who have a this huge CNC machine in their garage and were running their own business. I already knew them because I had installed the wiring that runs their machine. The beauty of a CNC (Computer Numerical Control) is that once the file for the parts are generated, the machine can make 1 or 1,000 all uniformly the same. After the first one, any number can be made on demand at any time.
When the old Corolla manifolds were manufactured, the runners were all stuck into identically machined flanges so they all ended up exactly in the same position. The machinist said that's no problem in that he can capture a profile of the runners as well as the profile of the head intake configuration, and the computer will generate the information to create a seamlessly smooth transition blending their difference from the outer surface of the flange to the inner surface. the flange will even have all of the original Yaris 0 type gasket grooves to accept an OEM gasket. It will also have a recess on the outer surface into which the runners will be inserted to insure they remain in the proper position during welding.
Maybe! And to go back to Tooter's point about wealth, that is when wealth will be created, not before. So far, a fee has been paid for a service to add "value" to a part. Wealth is created only when the part is sold with the added value included (aka profit), not before.From the point of view of the machinist, he created wealth by making a profit on the materials he supplied, on his machine, on his time, and on his considerable intake manifold design experience. I'm totally happy to pay him whatever he wants because he is making this project possible.
It's a win/win situation for both of us. 🙂🙂
...and you're exactly right that from my point of view, no wealth is created until a part is actually sold. 👍
How about loping off plenum also...which would allow the runners to be repositioned...then make a new yaris specific plenum...? Not really too much work...and to be honest the corolla plenum is but ugly on the outside. And one could do like a reverse merge collector for a smooth transition into each runner.
Jeez... my mind is already going a million miles a minute on all the possibilities. 🙄 But for now it's staying focusing on addressing just one detail at a time so as not to break the natural unfolding order of the flow of events. 😉
I do understand what you mean, which is why I like this particular manifold design so much. It's just a backwards equal length 4-1 header. Heck, if something flows one way, it'll flow the other. 👍
I was even wondering about a backwards 4-2-1 header intake manifold design like the Weapon R and if it would produce more torque with the alternately firing cylinders drawing from the same runner the same way they do on the header. 🙄 The intake on my truck is a 8-4-1. Also thinking about chopping the runners where they are all parallel with each other and lengthening them with some short straight tubing sections. That's just a few ideas... there's lots more, as the possibilities are endless.
Anyways, tomorrow I'll be back at the machine shop to go over some more manifold details. This is no end of fun. 🙂
I do understand what you mean, which is why I like this particular manifold design so much. It's just a backwards equal length 4-1 header. Heck, if something flows one way, it'll flow the other. 👍
I was even wondering about a backwards 4-2-1 header intake manifold design like the Weapon R and if it would produce more torque with the alternately firing cylinders drawing from the same runner the same way they do on the header. 🙄 The intake on my truck is a 8-4-1. Also thinking about chopping the runners where they are all parallel with each other and lengthening them with some short straight tubing sections. That's just a few ideas... there's lots more, as the possibilities are endless.
Anyways, tomorrow I'll be back at the machine shop to go over some more manifold details. This is no end of fun. 🙂
Well, the project is under way... 👍
...and I get to get to see the whole manufacturing process. From CAD design, to 3D rendering, generating the operating code, to watching the CNC actually make the first parts.
We're starting out with producing just one prototype set of adapters. Then comes assembly and welding. They know a first rate highly experienced professional welder who does beautiful work. Then I'll be installing it on my car to work out all the fitment, alignment, clearance, and operating issues.
Oooh... this is so exciting. 🙂
...and I get to get to see the whole manufacturing process. From CAD design, to 3D rendering, generating the operating code, to watching the CNC actually make the first parts.
We're starting out with producing just one prototype set of adapters. Then comes assembly and welding. They know a first rate highly experienced professional welder who does beautiful work. Then I'll be installing it on my car to work out all the fitment, alignment, clearance, and operating issues.
Oooh... this is so exciting. 🙂
I have a buddy who did Mech Eng @ Waterloo, he said the corolla type of intake is hard to get right, even with complex modelling software... he had access to Ricardo Wave (look it up, it's used by automakers).
Hope it works out though, be awesome to get a low dollar intake that does soemthing :)
Hope it works out though, be awesome to get a low dollar intake that does soemthing :)
question is "will it still be low when it is all said and done?" I don't know what the fab and flange are going to run but if it does some magic and adds ponies for lass than 250 i'm in for one once Micro Image gets the specs and make me one in red ;)
It's highly likely that it will do nothing except look really cool. 😉Originally Posted by Viperoni ↑I have a buddy who did Mech Eng @ Waterloo, he said the corolla type of intake is hard to get right, even with complex modelling software...
Yes it is, because of the compound angles generated to make the runners of equal length all originating from four different locations and ending up all pointing in the same direction and all terminating in exactly the same plane. The same principles apply to manufacturing exhaust headers.
Hope it works out though, be awesome to get a low dollar intake that does soemthing :)
I can tell you that mine is costing a prohibitive amount of money. Also, I honestly don't how this is all going to shake out because I have no idea if it will actually make any real world power improvements over the stock manifold.Originally Posted by Golddeenoh ↑question is "will it still be low when it is all said and done?"
And remember...
Toyota holds the decisive edge with the latest cutting edge technology computer modelling and the unlimited ability of plastic to be injection molded into any conceivable shape.
I'm just recycling a 14 year old junk yard part. 😆
So my only edge is that it was designed to flow for engine that's 20% larger than the 1NZ-FE.
Been nosing around the internet and found the very strange Prius manifold that also fits the Yaris engine...
Picture not included in this copy
It was designed to operate optimally within a very narrow range between 2,180 to 2,470 rpm.
Picture not included in this copy
It was designed to operate optimally within a very narrow range between 2,180 to 2,470 rpm.
I wonder what Prius operates within that rpm range. 🤷
I certainly could be wrong, Garm... 😆
...but got that operating range from a Japanese Prius site that had all sorts of technical data on the Prius engine. I believe that's why the engine uses such a strange intake manifold. If it was designed for optimal operating over a wide rpm rate like a regular car and not as a battery charger, I think it would have had a manifold just like ours is. That manifold design is the same as stationary utility engines that only run at a preset speed.
...but got that operating range from a Japanese Prius site that had all sorts of technical data on the Prius engine. I believe that's why the engine uses such a strange intake manifold. If it was designed for optimal operating over a wide rpm rate like a regular car and not as a battery charger, I think it would have had a manifold just like ours is. That manifold design is the same as stationary utility engines that only run at a preset speed.
Wow... 😲
Look at this!
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
This is exactly what I was referring to... an equal length runner header design used in reverse flow for an intake manifold. 👍
Looks like a plenum is added onto it so that it can be tuned by size.
And by the way... look at the mounting flange. It fits a Yaris engine. 🙂
There's also some really informative text along with the pics. It's worth reading:
Here's a link to the whole thing. It's called the Toyota Limo Project
http://limoku.blogspot.com/2010/10/c...his-first.html
Check the materials... he got a bunch of stuff from Micro Image! 🙂
Look at this!
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
This is exactly what I was referring to... an equal length runner header design used in reverse flow for an intake manifold. 👍
Looks like a plenum is added onto it so that it can be tuned by size.
And by the way... look at the mounting flange. It fits a Yaris engine. 🙂
There's also some really informative text along with the pics. It's worth reading:
It's odd that it mentions that longer runners make more high end power and shorter runners make more low end power. I always believed that to be the opposite. 😕 The article sounds like it was translated so maybe they got that detail backwards.
The Intake Manifold
While it's not easy to modify an existing intake manifold because it requires specialized aluminum welding, this section will discuss what to look out for when choosing an aftermarket intake manifold, or having your existing intake manifold modified. The intake manifold actually consists of two distinct parts that can be tuned separately. The two parts are:THE PLENUM
- the plenum, which is an air chamber that distributes air to the various cylinders
- the intake manifold runners, which connect each cylinder to the plenum
The main purpose of the plenum is to equalize the air flow to the various cylinders, but its volume and shape, as well as the shape of thebell mouths, which are the opening to the runners, are also important. Generally, a plenum volume of approximately 80% of engine capacity for naturally aspirated engines to 150% of engine capacity for turbocharged engines works best.
In terms of function, the best plenum design would have the air duct feed the center of the plenum. Unfortunately, due to space limitations and production costs, manufacturers tend to build plenums that are fed from one end, with the plenum blocked off at the other end. This results in air rushing to the far end of the plenum and creates a slight imbalance of air flow to the individual cylinders are the air will tend to flow past the first cylinder and collect at the far end of the cylinder, which is usually at the last cylinder. Consequently, the first cylinder will run slightly lean while the last cylinder will run slightly rich.
The easiest solution to this problem is to fit a second throttle body to the far end of the plenum and fit a double air filter, intake system. But this only works on naturally aspirated engines that have sufficient space for a second intake system. On supercharged and turbocharged engines this solution is not feasible and you would need to modify the plenum or fit an aftermarket intake manifold with a more efficient air flow and air distribution design. There are three things you must consider when modifying the plenum or selecting an aftermarket intake manifold.INTAKE RUNNERS
- First, the plenum should increase in size rapidly well before the first cylinder.
- Second, the plenum can taper towards the end from after the first cylinder but it should not taper to less than 1½ times the diameter of the intake runners.
- Third, the plenum should extend well beyond the last cylinder.
As is the case with the primary exhaust pipes, the diameter and length of the intake manifold runners influence the power curve of the engine. The intake runner diameter influences the point at which peak power is reached while the intake runner length will influence the amount of power available at high and low RPM.
A larger diameter intake runner will result in improved engine breathing at high RPM and will take peak engine power to a higher RPM but will have little low RPM power. This may be good for a modified race car or a drag car, but will not be good for a turbocharged car with a large turbocharger. For a good responsive modified street car or a rally car you would want an intake manifold runner diameter that is approximately 80% the size of the intake valve diameter on a two-valve cylinder, or the same size as the intake valve diameter on a four-valve cylinder. For a high performance modified race car or a drag race car you would want an intake manifold runner diameter that is approximately 90% the size of the intake valve diameter on a two-valve cylinder, or approximately 110% the size of the intake valve diameter on a four-valve cylinder.
In terms of intake manifold runner length, a longer intake runner produces better power at high RPM, while a shorter intake runner produces better power at low PRM. Generally, an intake manifold runner that is in the region of 300-400 mm long will sustain power at high RPM but little power at low RPM while an intake manifold runner that is in the region of 200-300 mm long will start building power from low RPM but will run out of power soon after peak power is reached. But note that the intake port on the cylinder head forms part of the intake runner. Thus the intake runner length is measured from the intake valve seat to the intake runner bell mouth, and not from the end of the intake manifold.
As with tuning your exhaust system, the intake manifold is best tuned on a dynometer, but it is much more difficult to make changes to the intake manifold so starting from a good base is best.
Here's a link to the whole thing. It's called the Toyota Limo Project
http://limoku.blogspot.com/2010/10/c...his-first.html
Check the materials... he got a bunch of stuff from Micro Image! 🙂
It's odd that it mentions that longer runners make more high end power and shorter runners make more low end power. I always believed that to be the opposite.Very odd. 😆
cool find though! This thread will have every manifold possibility in it.
Yes I hope so, as I thoroughly enjoy exploring all of the possibilities with every kind of search available to turn up everyone's ideas from all over the world.
This design is highly intriguing because it's exactly like a header...
Picture not included in this copy
And for a one off scratchbuilt manifold, it's impeccably assembled. 👍
But notice, it has one drawback...
...the runners are not equal length because it's impossible to execute this design without some of the runners going in the opposite direction before they meet in the collector. But then again, it was built specifically for forced induction so that would likely mitigate the runners' inequalities...
Picture not included in this copy
...whereas these runners are all equal length which is best for a normally aspirated engine. 👍
This bit about plenum design caught my eye...
Picture not included in this copy
I'm still avidly searching the web, so anything else that turns up, you'll see it here. 🙂
This design is highly intriguing because it's exactly like a header...
Picture not included in this copy
And for a one off scratchbuilt manifold, it's impeccably assembled. 👍
But notice, it has one drawback...
...the runners are not equal length because it's impossible to execute this design without some of the runners going in the opposite direction before they meet in the collector. But then again, it was built specifically for forced induction so that would likely mitigate the runners' inequalities...
Picture not included in this copy
...whereas these runners are all equal length which is best for a normally aspirated engine. 👍
This bit about plenum design caught my eye...
In terms of function, the best plenum design would have the air duct feed the center of the plenum. Unfortunately, due to space limitations and production costs, manufacturers tend to build plenums that are fed from one end, with the plenum blocked off at the other end. This results in air rushing to the far end of the plenum and creates a slight imbalance of air flow to the individual cylinders are the air will tend to flow past the first cylinder and collect at the far end of the cylinder, which is usually at the last cylinder. Consequently, the first cylinder will run slightly lean while the last cylinder will run slightly rich.The Corolla manifold design completely resolves all of flow imbalance issues, because it has an intake tube behind the throttle body that empties directly into the center of the plenum... 👍
Picture not included in this copy
I'm still avidly searching the web, so anything else that turns up, you'll see it here. 🙂
Here's that same Corolla manifold with Individual Throttle Body Injectors... 🙂
Picture not included in this copy
Picture not included in this copy
Here's that same manifold on a VW GTI... 😉
Picture not included in this copy
They're turning up everywhere! 🙂
Picture not included in this copy
They're turning up everywhere! 🙂
^ all these pick of them on other cars, I just want to see yours on yours and see a before and after dyno run. :D
One other solution to the side-mount TB is to use a tapered plenum:
Picture not included in this copy
As far as runner length, all of the material that I have read insists that longer runners = low end power and vice versa. This is all based on the Helmholtz resonator theory. If you look at the first equation (relax, you don't have to solve it) you can see that the mass of air in the neck is in the denominator, meaning that larger masses of air (longer runners) will decrease the resonant frequency (RPMs). Increasing the cross sectional area will increase the frequency, as well as have a slowing effect on air flow velocity in the runners. The variables for the 'cavity' refer to the cylinder, not the plenum.
tl;dr - science says long runner = low rpm boost. Unless this article has empirical evidence to back up their claims, treat it as snake oil.
Picture not included in this copy
As far as runner length, all of the material that I have read insists that longer runners = low end power and vice versa. This is all based on the Helmholtz resonator theory. If you look at the first equation (relax, you don't have to solve it) you can see that the mass of air in the neck is in the denominator, meaning that larger masses of air (longer runners) will decrease the resonant frequency (RPMs). Increasing the cross sectional area will increase the frequency, as well as have a slowing effect on air flow velocity in the runners. The variables for the 'cavity' refer to the cylinder, not the plenum.
tl;dr - science says long runner = low rpm boost. Unless this article has empirical evidence to back up their claims, treat it as snake oil.
Hey Cranky, 🙂Originally Posted by CrankyOldMan ↑One other solution to the side-mount TB is to use a tapered plenum:
Picture not included in this copy
As far as runner length, all of the material that I have read insists that longer runners = low end power and vice versa. This is all based on the Helmholtz resonator theory. If you look at the first equation (relax, you don't have to solve it) you can see that the mass of air in the neck is in the denominator, meaning that larger masses of air (longer runners) will decrease the resonant frequency (RPMs). Increasing the cross sectional area will increase the frequency, as well as have a slowing effect on air flow velocity in the runners. The variables for the 'cavity' refer to the cylinder, not the plenum.
tl;dr - science says long runner = low rpm boost. Unless this article has empirical evidence to back up their claims, treat it as snake oil.
I'm certain that was simply an transposing error in the translation. The project was done in Jakarta, Indonesia. And whoever did it had extensive practical automotive experience. I'll bet it did not read that way in the original language.
As to the intake manifold picture... just look at what you need to add to the manifold to try to overcome the inherent runner imbalances from taking fuel/air perpendicular to the axis of flow from the throttle body.
In my opinion it's much easier to simply use a design with no imbalances that need to be overcome in the first place. 👍
Cars today no longer have the luxury of large empty underhood spaces in which to fit those complex wildly expanded designs. My old truck does...
Picture not included in this copy
...but those days are long gone.😉
As do I. 🙂Originally Posted by Golddeenoh ↑^ all these pick of them on other cars, I just want to see yours on yours and see a before and after dyno run. :D
This is a process that needs to run its course, and I'm taking each step carefully and deliberately so that I don't have to backtrack.
Backtracking triples the cost of any project because of you're adding two more cost layers of undoing and redoing. It's already expensive enough just doing it once! 😆
In 1987, Oldsmobile introduced a DOHC 4 valve "Quad 4" engine. It used an unequal length intake manifold with no plenum...
Picture not included in this copy
Later years changed to a log type manifold likely because it worked better.
Picture not included in this copy
Picture not included in this copy
Later years changed to a log type manifold likely because it worked better.
Picture not included in this copy
Backtracking triples the cost of any project because of you're adding two more cost layers of undoing and redoing.More expensive, yes - triple, no. It's never 100% undo and redo, if the original idea was sound at all.
Giving up on an idea is a total loss though, I do know that one! For example, if the intake manifold causes a loss in power, I wouldn't bring it to market.
A nice Corolla engine. Hope mine looks half as nice...Picture not included in this copy
Hey Garm, 🙂Originally Posted by cali yaris ↑More expensive, yes - triple, no. It's never 100% undo and redo, if the original idea was sound at all.
Giving up on an idea is a total loss though, I do know that one! For example, if the intake manifold causes a loss in power, I wouldn't bring it to market.
You're right. That was a little hyperbolic just for a manifold. 😆 I work in construction where the triple rule is more of a reality.
By the way how are your manifolds progressing? I just started and I'm a totally inexperienced amateur, so you had better not let me get a manifold on my car before you get one on yours. 😛
But I bet yours will work better than my junkyard special... 😉
I'm pretty sure you'll have yours on first!
We have a prototype now that doesn't hit anything. 😆 It's tack-welded though, so it can't be installed on a car. Next revision will be a proto we can put on a car and see what happens. Maybe another week or two?
I wish I could focus on this the way you're focusing on this. 👏
We have a prototype now that doesn't hit anything. 😆 It's tack-welded though, so it can't be installed on a car. Next revision will be a proto we can put on a car and see what happens. Maybe another week or two?
I wish I could focus on this the way you're focusing on this. 👏
This project is just a hobby to play around with in my spare time. But I've been interested in intake and exhaust designs and how they flow for most of my life, so the opportunity to do this is a dream come true. 🙂
OK, I've tinkered around with the suggested dimensions you gave me and it doesn't really look right. If you have access to a laser printer with high dimensional fidelity (and 11x17 paper) you could print these off and compare them to the original. I can't find the thermal gasket in the MI store--was it a special order item?
2 attachments not included in this copy
^ Haven't put them up yet 🙁 in stock though!
[edit] uploaded into the store now Yaris > Engine > Mechanicals
[edit] uploaded into the store now Yaris > Engine > Mechanicals
Hey Cranky, 🙂
Sorry my measurements weren't so good... 🙁 and I'm presently at a disadvantage as everything is down at the machine shop because they are generating the working drawings.
My own less-than-machinist accuracy is one reason why I simply got both the thermal gasket and a stock manifold. They completely remove all the guesswork, as there is an actual physical representation of everything required to make the adaptor flange fit properly.
Hey wait, I think I see why the measurements aren't working out with your drawing!
None of the Corolla manifold runners are concentric with the Yaris head intake ports. Your part as drawn indicates that they are. First, the Corolla runners are a lot larger, and second they more spread out.
Consider just the two inner Corolla runners first:
The two inner edges of the Corolla runners perfectly line up with the inside edges of the two inner Yaris intake ports. The distance between the two corolla runners and the distance between the two Yaris intake ports are exactly the same. That distance is the only one that matches exactly. All of the other measurements are different. Even the bolt holes bear no symmetrical relationship to the Corolla runners.
Now consider the two outer Corolla runners. Both of their inner edges are 5mm outside of the outer edge of the Yaris runners. This is one reason why I'm specifying the flange be one inch thick, so that there will be sufficient distance to make a smooth flowing transition between the two different arrays of holes.
Just email or call Garm and he'll sell you the thermal gasket. It's made by Golden Eagle. It'll make your task so much easier! 👍
I'm going to use it on my car. And you can make good use of it on yours. The intake manifold flange is really thick aluminium and will pick up conductive heat from the head. The thermal gasket will insulate it and keep it cooler.👍
Sorry my measurements weren't so good... 🙁 and I'm presently at a disadvantage as everything is down at the machine shop because they are generating the working drawings.
My own less-than-machinist accuracy is one reason why I simply got both the thermal gasket and a stock manifold. They completely remove all the guesswork, as there is an actual physical representation of everything required to make the adaptor flange fit properly.
Hey wait, I think I see why the measurements aren't working out with your drawing!
None of the Corolla manifold runners are concentric with the Yaris head intake ports. Your part as drawn indicates that they are. First, the Corolla runners are a lot larger, and second they more spread out.
Consider just the two inner Corolla runners first:
The two inner edges of the Corolla runners perfectly line up with the inside edges of the two inner Yaris intake ports. The distance between the two corolla runners and the distance between the two Yaris intake ports are exactly the same. That distance is the only one that matches exactly. All of the other measurements are different. Even the bolt holes bear no symmetrical relationship to the Corolla runners.
Now consider the two outer Corolla runners. Both of their inner edges are 5mm outside of the outer edge of the Yaris runners. This is one reason why I'm specifying the flange be one inch thick, so that there will be sufficient distance to make a smooth flowing transition between the two different arrays of holes.
Just email or call Garm and he'll sell you the thermal gasket. It's made by Golden Eagle. It'll make your task so much easier! 👍
I'm going to use it on my car. And you can make good use of it on yours. The intake manifold flange is really thick aluminium and will pick up conductive heat from the head. The thermal gasket will insulate it and keep it cooler.👍
Thanks, Garm. 👍
It's an especially useful part because it not only pins down all the measurements exactly, it will get put into use when I install the manifold.
It's an especially useful part because it not only pins down all the measurements exactly, it will get put into use when I install the manifold.
Oh, I had intended to cut the runners from the plenum for my design, so I made them concentric. If you look carefully, the runners holes are proportionately wider than the intake holes. I had considered what you were planning, but decided it was too much of a stretch and would make machining it a nightmare.
The 1NZ has 83mm bore spacing and the intake has (iirc) 87.5mm spacing. I had that written down somewhere...
The 1NZ has 83mm bore spacing and the intake has (iirc) 87.5mm spacing. I had that written down somewhere...
Ok, I get it now. 👍Originally Posted by CrankyOldMan ↑Oh, I had intended to cut the runners from the plenum for my design, so I made them concentric.
I didn't know that you were going to cut apart the manifold runners.
If you look carefully, the runners holes are proportionately wider than the intake holes.Yes... and no wonder you showed them concentric.
I had considered what you were planning, but decided it was too much of a stretch and would make machining it a nightmare.Are you going to machine it yourself? It would be a tough job trying to correct the offsets which is good you're not going that route. That's why my friend suggested hiring someone with a CNC machine, because it's a simple matter for it to render the difference between the two arrays smoothly.
The 1NZ has 83mm bore spacing and the intake has (iirc) 87.5mm spacing. I had that written down somewhere...Note how none of the runners surfaces physically touches any of the other runners. When you cut them apart to reposition them, it would be a good idea to make sure that there is no contact between them as under vibration they can chafe. I worked on helicopters as a mechanic in the Army, and preventing aluminium parts from chafing during flight was always an issue... not that our Yaris' could ever fly! 😆
I have access to CNC mills at school and AutoCAD at home, so that's not a big deal. The issue I was considering was the inset channel for the runners being on the opposite side of the machining face. Any time you relocate a part, you're asking for alignment issues. We're not trained/allowed to use edge finders on the equipment at school, so it has to be a single-sided operation. Now if I could just get AutoCAD to stop crashing, I could get this new plate drawn up...Originally Posted by tooter ↑Are you going to machine it yourself? It would be a tough job trying to correct the offsets which is good you're not going that route. That's why my friend suggested hiring someone with a CNC machine, because it's a simple matter for it to render the difference between the two arrays smoothly.
All right, Crank! Man, you're certainly going to win the contest hands down of building the cheapest manifold! 👍Originally Posted by CrankyOldMan ↑I have access to CNC mills at school and AutoCAD at home, so that's not a big deal.
The issue I was considering was the inset channel for the runners being on the opposite side of the machining face. Any time you relocate a part, you're asking for alignment issues. We're not trained/allowed to use edge finders on the equipment at school, so it has to be a single-sided operation.Oh, this is something I know absolutely nothing about. All I know is that the machinists told me that making the adaptor was a simple straightforward job for them.
Now if I could just get AutoCAD to stop crashing, I could get this new plate drawn up...Good luck... and do keep me posted on how your project goes. Sometimes two people figuring out how to do the same thing can come up with new and different approaches and techniques. 🙂
OK, I got it to cooperate long enough to get something banged out. Here's the problem I was anticipating with the overhang:
Picture not included in this copy
The left hole is OK to machine from one side. It's not really possible to mill this shape on the right without a 5-axis mill, tilting the flange after milling the inset groove, or flipping the part over in the middle of machining that opening--none of which is possible/practical for me.
*edit*
One alternative I've thought of would be to bore the head side hole straight through on the left edge and backfill the difference when welding and die grind the bore smooth.
Picture not included in this copy
The left hole is OK to machine from one side. It's not really possible to mill this shape on the right without a 5-axis mill, tilting the flange after milling the inset groove, or flipping the part over in the middle of machining that opening--none of which is possible/practical for me.
*edit*
One alternative I've thought of would be to bore the head side hole straight through on the left edge and backfill the difference when welding and die grind the bore smooth.
Just mill the vertical surfaces and Dremel the angle yourself! 👍
The aluminium is soft. I had already been practicing on the old flange and using a good bit, the stuff peels off smooth like cold butter. Make the outer holes smaller and then feather them out to meet the inner edge of the outer Yaris ports.
Heck, when I first started out I was going to do the whole thing by hand with a drill press and a Dremel! 😆
I was just going to trace the Yaris gasket on one side of a 25mm slab and draw around the Corolla runners on the other side. Then use a drill press to punch out all of the vertically matching areas that go all the way through and Dremel the rest.
Oh, the guys let me in on another tip...
The 25mm bars we're getting have manufacturing rolling/extruding stresses in them and can warp under the heat of welding. So they're going to mill both sides flat and true to remove the more highly stressed and compressed metal at the surfaces. Then they'll lay flat under welding heat. 👍
Any other ideas that are related to me I'll share them with you. 🙂
The aluminium is soft. I had already been practicing on the old flange and using a good bit, the stuff peels off smooth like cold butter. Make the outer holes smaller and then feather them out to meet the inner edge of the outer Yaris ports.
Heck, when I first started out I was going to do the whole thing by hand with a drill press and a Dremel! 😆
I was just going to trace the Yaris gasket on one side of a 25mm slab and draw around the Corolla runners on the other side. Then use a drill press to punch out all of the vertically matching areas that go all the way through and Dremel the rest.
Oh, the guys let me in on another tip...
The 25mm bars we're getting have manufacturing rolling/extruding stresses in them and can warp under the heat of welding. So they're going to mill both sides flat and true to remove the more highly stressed and compressed metal at the surfaces. Then they'll lay flat under welding heat. 👍
Any other ideas that are related to me I'll share them with you. 🙂
I found a local speed shop that will dyno test my car to document the baseline performance so that when the manifold is installed and dyno tested, I'll have something to compare it against.
An aftermarket intake was needed as the stock air box will not work with the new manifold do to the repositioned throttle body. So I'm cobbling together two different systems. After looking at absolutely every intake made, I really like the BLOX air filter kit the most 👍because it was the only one I found that uses a true velocity stack as its base and has a dry element (no oil to deal with) air filter attached onto it...
Picture not included in this copy
The BLOX will be installed onto a Weapon R Short Ram Intake tube...
Picture not included in this copy
I picked the Weapon R because the high polish not only looks good, it's simple, direct, and cheap... and the Blox Velocity Stack fits right onto it. The repositioned throttle body poses no problem for the Weapon R as there is plenty of room to rotate the pipe to locate the air filter in a good spot.
So the baseline dyno test will be:
BLOX Velocity Stack Dry Element Air Filter
Weapon R Short Ram intake
Weapon R 4-2-1 Exhaust Header
Micro Image MagnaFlow Center Exit Exhaust
And only change for comparison will be the modified Corolla intake manifold.
The velocity stack comes in a few days so I'll be installing the intake. And the car is almost has 1,000 miles on it, over a grand, it should be broken in enough for a few dyno runs. 🙂
I'll post the chart as soon as the first runs are done.
An aftermarket intake was needed as the stock air box will not work with the new manifold do to the repositioned throttle body. So I'm cobbling together two different systems. After looking at absolutely every intake made, I really like the BLOX air filter kit the most 👍because it was the only one I found that uses a true velocity stack as its base and has a dry element (no oil to deal with) air filter attached onto it...
Picture not included in this copy
The BLOX will be installed onto a Weapon R Short Ram Intake tube...
Picture not included in this copy
I picked the Weapon R because the high polish not only looks good, it's simple, direct, and cheap... and the Blox Velocity Stack fits right onto it. The repositioned throttle body poses no problem for the Weapon R as there is plenty of room to rotate the pipe to locate the air filter in a good spot.
So the baseline dyno test will be:
BLOX Velocity Stack Dry Element Air Filter
Weapon R Short Ram intake
Weapon R 4-2-1 Exhaust Header
Micro Image MagnaFlow Center Exit Exhaust
And only change for comparison will be the modified Corolla intake manifold.
The velocity stack comes in a few days so I'll be installing the intake. And the car is almost has 1,000 miles on it, over a grand, it should be broken in enough for a few dyno runs. 🙂
I'll post the chart as soon as the first runs are done.
Exciting - real data!
...which shop is doing your dyno?
...which shop is doing your dyno?
AFE filters are dry or oiled, by the way.
Hey Garm, 🙂
HK Motorsports on Oxnard in Van Nuys is going to do it. I already talked to Harry.
The AFE is a good SRI system, but I didn't care for the black plastic tubing with those tight bends. Also considered the K&N SRI. It has free play without the box, but I didn't want to deal with an oily filter. Neither of those would work anyways as the attitude of the throttle body is going to end up being altered from the stock position in two axes. A free floating system serves my needs better because I can rotate it to fit, and there is no box to restrict the filter location.
I might have a go at polishing the runners on the Corolla manifold, so the highly polished Weapon R tube should compliment them, and I really like the design of the BLOX velocity stacks. 👍
Picture not included in this copy
The throat is 2.5 inches inside diameter which perfectly matches the Weapon R aluminium pipe. Then it smoothly flares out to about 5 inches. An elegantly simple practical free flowing design. 🙂
Here's a really cool demonstration of the same beautiful principle using flowing water instead of air...
http://www.youtube.com/watch?v=eCdqZFtb-BQ&feature=fvst
HK Motorsports on Oxnard in Van Nuys is going to do it. I already talked to Harry.
The AFE is a good SRI system, but I didn't care for the black plastic tubing with those tight bends. Also considered the K&N SRI. It has free play without the box, but I didn't want to deal with an oily filter. Neither of those would work anyways as the attitude of the throttle body is going to end up being altered from the stock position in two axes. A free floating system serves my needs better because I can rotate it to fit, and there is no box to restrict the filter location.
I might have a go at polishing the runners on the Corolla manifold, so the highly polished Weapon R tube should compliment them, and I really like the design of the BLOX velocity stacks. 👍
Picture not included in this copy
The throat is 2.5 inches inside diameter which perfectly matches the Weapon R aluminium pipe. Then it smoothly flares out to about 5 inches. An elegantly simple practical free flowing design. 🙂
Here's a really cool demonstration of the same beautiful principle using flowing water instead of air...
http://www.youtube.com/watch?v=eCdqZFtb-BQ&feature=fvst
Been reading about velocity stacks and discovered that they're also called flow stacks...
Picture not included in this copy
This is a cross section of the BPI flow stack air filter which is exactly the same design as the BLOX. I can't tell, they might be the same manufacturer...
Picture not included in this copy
Picture not included in this copy
This is a cross section of the BPI flow stack air filter which is exactly the same design as the BLOX. I can't tell, they might be the same manufacturer...
Picture not included in this copy
Here's a video of a normally aspirated engine with velocity stacks...
http://www.youtube.com/watch?v=9GAbgqz4yGs
Crank up the sound... it will positively blow your mind! 😲
An S2000 with stacks...
http://www.youtube.com/watch?v=ccCIb...eature=related
http://www.youtube.com/watch?v=9GAbgqz4yGs
Crank up the sound... it will positively blow your mind! 😲
An S2000 with stacks...
http://www.youtube.com/watch?v=ccCIb...eature=related
Holy moly dymag wheels ! Spare no expense !
Where to get that flow stack tooter ?
Where to get that flow stack tooter ?
Got it as a complete kit off Ebay from the seller called "goodygarage". 🙂
He has 5. I bought one, so there are 4 still for sale.
Kit:
BLOX composite black 2.5" velocity stack (not aluminium)
6 inch dry element filter
2.5" silicone coupler to fit any 2.5' intake pipe
3 stainless steel screw clamps, big one for filter, 2 little ones for the mounting coupler
$57 with free shipping and including California sales tax. 🙂
It ships from back east so I won't receive it out here on the west coast until the 28th. Would ship to you quicker because you're closer.
He has 5. I bought one, so there are 4 still for sale.
Kit:
BLOX composite black 2.5" velocity stack (not aluminium)
6 inch dry element filter
2.5" silicone coupler to fit any 2.5' intake pipe
3 stainless steel screw clamps, big one for filter, 2 little ones for the mounting coupler
$57 with free shipping and including California sales tax. 🙂
It ships from back east so I won't receive it out here on the west coast until the 28th. Would ship to you quicker because you're closer.