I think that's an exhaust manifold, not an intake manifold?
tooter's manifold adventure...
1,454 posts · 559,522 views · page 4 of 30
Replies continued
*facepalm*
I'll just be over here in the corner, continuing to observe.
I'll just be over here in the corner, continuing to observe.
😆
Picture not included in this copy
but yeah.... less than $800. 👍
Interesting... 🙂
Looks like they tried to make the runners as long as they could by rotating them 90 degrees counterclockwise around the axis of the exhaust exit...
Picture not included in this copy
Looks like they tried to make the runners as long as they could by rotating them 90 degrees counterclockwise around the axis of the exhaust exit...
Picture not included in this copy
TRD Exhaust Manifold Header IST bB Vitz CorollaWhat a deal... for just eight. Does that include free shipping? I'll take the Weapon R for two. 😉
Was: $ 1,086.96 Sale: $ 869.57
Intake noise is really only apparent at WOT under load. Sitting still at idle generates nothing. Sitting still and punching the throttle only produces a brief sucking sound. Out on the road, WOT is what makes them growl, which btw, cannot be heard with anything but the oem exhaust installed.Originally Posted by tooter ↑There's not much intake noise even with the camera stuck up close.
That TRD header would add some real nice JDM swag to the Yaris.
Yes, I found that out when I did some flat out runs on the freeway last week, in preparation for the dyno tune. Could hear a slight roaring sound over the exhaust at wide open throttle.Originally Posted by WeeYari ↑Intake noise is really only apparent at WOT under load. Sitting still at idle generates nothing. Sitting still and punching the throttle only produces a brief sucking sound. Out on the road, WOT is what makes them growl, which btw, cannot be heard with anything but the oem exhaust installed.
In normal driving it's just as quiet as the stock air box... which makes the little lady happy. 😉
I think the Weapon R is much better looking...Originally Posted by 1.5 ↑That TRD header would add some real nice JDM swag to the Yaris.
...especially at 25% of the cost. 😉
Picture not included in this copy
Ive been running a ram air duct into my air box with the opening in the foglight hole. Ive ran 3 tanks this way with no noticeable difference in mpg. Highway power maybe feels better?
Im thinking ill make my own proper CAI using the blox...i really like that and i think i can squeeze it in the bumper...i got hammers...
Im thinking ill make my own proper CAI using the blox...i really like that and i think i can squeeze it in the bumper...i got hammers...
I got hammers... 😆Originally Posted by malibuguy ↑Ive been running a ram air duct into my air box with the opening in the foglight hole. Ive ran 3 tanks this way with no noticeable difference in mpg. Highway power maybe feels better?
Im thinking ill make my own proper CAI using the blox...i really like that and i think i can squeeze it in the bumper...i got hammers...
I was checking around on ebay and it appears that BLOX also makes a much smaller 4 inch diameter velocity stack filter...
Picture not included in this copy
You can tell the smaller filter diameter because it has almost no taper as compared to the 7.5 inch filter, but yet has the same black plastic end cap. The only unknown is the inlet diameter, but that could be determined simply by asking the seller. One negative... it's pricey at $77 including shipping.
edit: from checking around, that may actually be a 4 inch inlet filter and not useable on the Yaris. The seller could confirm whether the filter itself is 4 inch diameter, or the inlet is 4 inch diameter.
Well worse case scenario ill use an aem dry filter. I used a 2.5" vibrant filter when i fab'd the intake on my old xB...but it had a nasty internal lip to reduce it to 2.5" from 3"...friggen joke. I gave that filter away when i traded that in for the Yaris
I just emailed the ebay seller to find out for sure as I'm really curious about that. 😉
And the runners are still a bit too short to do anything very useful, but they're not far off. The problem is the downpipe mounts so close to the motor it's almost impossible to make a smooth & straight header that's long enough.Originally Posted by tooter ↑Interesting... 🙂
Looks like they tried to make the runners as long as they could by rotating them 90 degrees counterclockwise around the axis of the exhaust exit...
What a deal... for just eight. Does that include free shipping? I'll take the Weapon R for two. 😉
Ok went from intake manifold project to talking about headers and velocity stacks...
You're right. It needs to be like this Yaris Weapon R header to make a real difference...Originally Posted by Viperoni ↑And the runners are still a bit too short to do anything very useful, but they're not far off. The problem is the downpipe mounts so close to the motor it's almost impossible to make a smooth & straight header that's long enough.
Picture not included in this copy
I'll be sure to let you know everything that happens on the manifold project. I'm getting a baseline dyno on Thrusday and will post the results here. 🙂Originally Posted by blacksandiegovitz ↑Ok went from intake manifold project to talking about headers and velocity stacks...
Just read the old 2008 thread on Richard Holdener's intake manifold...
Picture not included in this copy
Over the last 4 years it appears like there has been a constant string of obstacles and setbacks which have prevented anyone from being able to produce a better intake manifold than the one which is already on the engine.
In the light of what I've just been reading, makes it extremely unlikely that my Yaris is going to run any better with a jiggered 14 year old Corolla manifold on it, even though I'm already into the project for about $1,400 and just getting started! 😆
Nevertheless, I'm going to find out, not to arrive at some goal, but just for the personal enjoyment of following my own uneducated interest in flow design. I like to follow my own intuition just to see where it leads me, and I'm happy to share the details of every event as it unfolds with all of you. 🙂
Picture not included in this copy
Over the last 4 years it appears like there has been a constant string of obstacles and setbacks which have prevented anyone from being able to produce a better intake manifold than the one which is already on the engine.
In the light of what I've just been reading, makes it extremely unlikely that my Yaris is going to run any better with a jiggered 14 year old Corolla manifold on it, even though I'm already into the project for about $1,400 and just getting started! 😆
Nevertheless, I'm going to find out, not to arrive at some goal, but just for the personal enjoyment of following my own uneducated interest in flow design. I like to follow my own intuition just to see where it leads me, and I'm happy to share the details of every event as it unfolds with all of you. 🙂
Just figure out how to import this exhaust to the states.Originally Posted by tooter ↑You're right. It needs to be like this Yaris Weapon R header to make a real difference...
Picture not included in this copy
http://www.kansaiexhaust.com/product...ction=category
Picture not included in this copy
There's no need for importing another long runner Yaris header when that Weapon R pictured above is already available right now on ebay for only $245 including shipping. 🙂
what's the difference between that 2 pc weapon R header than the one you have, Tooter ?
That looks to be an incorrect stock photo - here's the link to the only Yaris header on Weapon-R's site: http://www.weapon-r.com/index.php?ac...product&id=607Originally Posted by tooter ↑You're right. It needs to be like this Yaris Weapon R header to make a real difference...
Picture not included in this copy
The Kansai exhaust header is more or less what mine will look like.
Except that one is made with crush bent tubing, such a shame.
👍Originally Posted by tooter ↑
In the light of what I've just been reading, makes it extremely unlikely that my Yaris is going to run any better with a jiggered 14 year old Corolla manifold on it, even though I'm already into the project for about $1,400 and just getting started! 😆
Nevertheless, I'm going to find out, not to arrive at some goal, but just for the personal enjoyment of following my own uneducated interest in flow design. I like to follow my own intuition just to see where it leads me, and I'm happy to share the details of every event as it unfolds with all of you. 🙂
That 2-piece WR header is for a k-series honda.
^ Correct. They never made it for the Yaris. IF there is one on eBay that is for the Yaris, it's made by someone else.
Yeah, I just took another look at that ebay auction. Scrolling down to the bottom, there's a disclaimer on the photo. 🙁 They're just selling the short header #953-116-108.
So that leaves this Kansai 4-2-1 as being the only long runner header...
Picture not included in this copy
The ad says: "Call for Price".
100,000,000,000 yen. 😆
So that leaves this Kansai 4-2-1 as being the only long runner header...
Picture not included in this copy
The ad says: "Call for Price".
100,000,000,000 yen. 😆
Trust me guys, if there were a long header available from an existing vendor, it would be in my store. 👍
Wow... are you actually making your own header? 😲Originally Posted by Viperoni ↑The Kansai exhaust header is more or less what mine will look like. Except that one is made with crush bent tubing, such a shame.
Do you have any pictures of it? 🙂
Ill be making one for mine too one day...its going to be a trick
Do you think it'll be a challenge to get the 02 sensor bung in the right place so as not to trigger the check engine light? If you could see there they put it on the Kansai, that might be a big help unless there aren't any on it to begin with.
The real challenge is that the o2 sensor is far enough away to get an accurate reading but not to far away that the results are delayed.
The CEL isn't really an issue with the front o2 as that is getting readings its the rear o2 that triggers the cat efficiency light.
The CEL isn't really an issue with the front o2 as that is getting readings its the rear o2 that triggers the cat efficiency light.
^ You don't have much choice - it need to be as soon after the final collector as possible. Hit and miss on whether it throws CEL's or not, it's not possible to predict with any certainty.
Usually just spacing the 2nd O2 sensor out of the exhaust stream just enough fools the ecu good enough...mine is currently spaced out now since toyota doesnt like anything other then a stock cat. And im running a 100cell race cat
Just got back from the dyno shop... 🙂
The results of the 3 runs was:
98.87HP
99.18FT/LB
99.90HP
101.00FT/LB
99.93HP
01.22FT/LB
Mods:
Weapon R Short Ram Intake with BLOX Velocity Stack Air Filter
Weapon R 4-2-1 Header
Micro Image MagnaFlow Center Exit Exhaust
So the engine essentially made 100HP with those mods.🙂
Here's the chart:
Picture not included in this copy
Does anyone have a dyno run of a completely stock Yaris for comparison?
I'm uploading the video to You Tube right now and will post the link as soon as it's done.
The dyno runs were done at this shop:
HK Motorsports
15020 Oxnard Street Unit A
Van Nuys, CA 91411
818-908-9650
http://www.hkmotorsportsdynoshop.com/
Harry, the owner is a good guy. 🙂
The results of the 3 runs was:
98.87HP
99.18FT/LB
99.90HP
101.00FT/LB
99.93HP
01.22FT/LB
Mods:
Weapon R Short Ram Intake with BLOX Velocity Stack Air Filter
Weapon R 4-2-1 Header
Micro Image MagnaFlow Center Exit Exhaust
So the engine essentially made 100HP with those mods.🙂
Here's the chart:
Picture not included in this copy
Does anyone have a dyno run of a completely stock Yaris for comparison?
I'm uploading the video to You Tube right now and will post the link as soon as it's done.
The dyno runs were done at this shop:
HK Motorsports
15020 Oxnard Street Unit A
Van Nuys, CA 91411
818-908-9650
http://www.hkmotorsportsdynoshop.com/
Harry, the owner is a good guy. 🙂
I believe that's about 10whp above stock... Not too shabby.
Yaris Dyno charts
*ahem*Originally Posted by tooter ↑Does anyone have a dyno run of a completely stock Yaris for comparison?
Yaris Dyno charts
Good results! I'm sure someone will chime in with stock dyno run, but unlikely we have one from a 2012 like yours. Your car has a different ECU than the 07-11 cars so it may net different results, certainly seems to like the few bolt-ons you've got so far!
Here's a video of the 4th gear run...
http://www.youtube.com/watch?v=rYF6pvhn96U
Hey Jeff... 🙂
Your MI exhaust sounds really cool! 👍
http://www.youtube.com/watch?v=rYF6pvhn96U
Hey Jeff... 🙂
Your MI exhaust sounds really cool! 👍
Damn...our cars really like exhaust then...i have less intake and more exhaust and have 7-8more whp.
I wonder how much a long header could really produce
I wonder how much a long header could really produce
For comparison, what intake and exhaust are you running? The bottleneck on mine is the stock mid tube.
If you plan to stay NA, start with the header...the stock "collector"(not sure if correct term) where the 4 pipes of the header joins together is very very small and that restricts quite abit of power
Stock air box...removed carbon filter and im running an Apex-i drop in replacement filter. I made a full custom 2" mandrelbent exhaust. I also have amsoil synthetic trans and engine oil. Also i have a weaponr header too
Ah, there's where you got those extra horses. 🙂
Since I have a header and an axleback, that bigest gain is found in the midpipe. 👍
Since I have a header and an axleback, that bigest gain is found in the midpipe. 👍
Yes, that's where I started, too. 🙂Originally Posted by ljming99 ↑If you plan to stay NA, start with the header...the stock "collector"(not sure if correct term) where the 4 pipes of the header joins together is very very small and that restricts quite abit of power
those numbers are interesting. I was hoping for around 105 or so. I am actually going to be going 2" from the resonator back with mine. there is a short section that is actually oval shaped that seems really restrictive.
I am really looking forward to seeing what your intake manifold does for you. any ETA on when that is going to be finished?
I am really looking forward to seeing what your intake manifold does for you. any ETA on when that is going to be finished?
I was hoping for 95 horsepower. 😆
After, all I've only done just a few simple peripheral mods.
The CNC guys were concurrently working on multiple machining deadlines so mine had been getting pushed back. The other projects are finished now so they're working on mine. Just talked with them this morning and they're modelling the face plate design to accept the stock intake manifold gasket. I want this to be something that everything fits properly so I can simply bolt it on and run it. 🙂
I showed the manifold to Harry, the guy who runs the dyno shop, and he told me that while the manifold should show some power gains above 4,000 it will be at the sacrifice of power down in the 2,000 to 3,000 rpm range. He said it was because the larger volume of the runners will slow down the velocity of the air at low rpms. The question is how much bottom end will be lost... I'll find that out on the next dynos. 😉
After, all I've only done just a few simple peripheral mods.
The CNC guys were concurrently working on multiple machining deadlines so mine had been getting pushed back. The other projects are finished now so they're working on mine. Just talked with them this morning and they're modelling the face plate design to accept the stock intake manifold gasket. I want this to be something that everything fits properly so I can simply bolt it on and run it. 🙂
I showed the manifold to Harry, the guy who runs the dyno shop, and he told me that while the manifold should show some power gains above 4,000 it will be at the sacrifice of power down in the 2,000 to 3,000 rpm range. He said it was because the larger volume of the runners will slow down the velocity of the air at low rpms. The question is how much bottom end will be lost... I'll find that out on the next dynos. 😉
it would be nice if you had a data file of the dyno and you could literally see the delta (positive or negative) in maybe 100 rpm steps. I know that it may be too late for that. maybe you could overlay the two dyno runs if your dyno guy keeps the files (I assume he would)
I like the progress you are making. it may be advantageous for you to go to a muffler shop and get them to replace that run of 1.75" pipe with 2"...obviously not until you get the intake manifold experiment done.
when you get the manifold done, we definitely need some pics of the final product also.
I like the progress you are making. it may be advantageous for you to go to a muffler shop and get them to replace that run of 1.75" pipe with 2"...obviously not until you get the intake manifold experiment done.
when you get the manifold done, we definitely need some pics of the final product also.
You mean like this? 🙂Originally Posted by BEEF ↑it would be nice if you had a data file of the dyno and you could literally see the delta (positive or negative) in maybe 100 rpm steps. I know that it may be too late for that.
Dynojet Research Inc.
Run Name: C:\DynoRuns\Toyota\2012 Toyota Yaris Greg Mamishian\RunFile_001.drf
Run Title: 2012 Toyota Yaris Greg Mamishian
Run Notes: Weapon R Intake
BLOX Velocity Stack Air Filter
Weapon R 4-2-1 Header
Micro Image MagnaFlow Exhaust
Run Date: 7/5/2012 12:07:06 PM
RunFile_001.drf: 78.46 °F 29.19 in-Hg Humidity: 45 % SAE: 1.02 Average Gear Ratio: 52.53
s RPM x1000 hp ft-lbs Air/Fuel
0.69 2.10 34.69 86.77 14.89
1.47 2.20 37.21 88.84 13.05
2.25 2.30 38.89 88.80 12.36
3.00 2.40 41.30 90.38 12.36
3.76 2.50 43.35 91.07 12.42
4.51 2.60 44.87 90.65 12.30
5.28 2.70 45.91 89.31 12.15
6.05 2.80 47.64 89.36 11.98
6.82 2.90 49.39 89.45 11.70
7.60 3.00 50.66 88.69 11.90
8.38 3.10 52.12 88.31 11.79
9.15 3.20 54.52 89.49 11.93
9.90 3.30 57.61 91.69 12.35
10.65 3.40 60.03 92.73 12.35
11.39 3.50 62.20 93.34 12.18
12.12 3.60 65.50 95.56 11.98
12.84 3.70 66.59 94.53 11.95
13.57 3.80 68.98 95.34 12.08
14.29 3.90 72.28 97.33 12.39
14.99 4.00 74.58 97.92 12.29
15.70 4.10 76.66 98.20 12.08
16.41 4.20 77.84 97.33 12.11
17.11 4.30 79.09 96.60 12.11
17.85 4.40 81.29 97.03 12.16
18.57 4.50 82.25 96.00 12.30
19.30 4.60 84.32 96.27 12.21
20.01 4.70 86.01 96.12 12.29
20.76 4.80 87.75 96.02 12.41
21.49 4.90 89.12 95.53 12.40
22.23 5.00 91.66 96.28 12.49
22.96 5.10 93.48 96.27 12.66
23.70 5.20 95.13 96.08 12.91
24.43 5.30 95.75 94.88 13.22
25.18 5.40 97.30 94.64 13.54
25.97 5.50 98.27 93.84 13.82
26.72 5.60 98.02 91.93 14.01
27.51 5.70 98.19 90.47 14.23
28.33 5.80 97.09 87.92 14.36
N/A 5.90 N/A N/A N/A
29.99 6.00 97.60 85.47 14.62
--------- --------- --------- --------- ---------
MAX: 29.99 6.00 98.27 98.20 14.89
MIN: 0.69 2.10 34.69 85.47 11.70
--------------------------------------------------------------------------------
Dynojet Research Inc.
Run Name: C:\DynoRuns\Toyota\2012 Toyota Yaris Greg Mamishian\RunFile_002.drf
Run Title: 2012 Toyota Yaris Greg Mamishian
Run Notes: Weapon R Intake
BLOX Velocity Stack Air Filter
Weapon R 4-2-1 Header
Micro Image MagnaFlow Exhaust
Run Date: 7/5/2012 12:17:31 PM
RunFile_002.drf: 79.85 °F 29.19 in-Hg Humidity: 43 % SAE: 1.02 Average Gear Ratio: 52.49
s RPM x1000 hp ft-lbs Air/Fuel
0.69 1.80 26.43 77.12 14.89
1.57 1.90 28.78 79.55 10.00
2.38 2.00 32.66 85.78 10.31
3.17 2.10 35.21 88.07 11.72
3.93 2.20 37.94 90.58 11.88
4.69 2.30 39.27 89.68 11.91
5.44 2.40 41.93 91.76 12.00
6.19 2.50 44.02 92.48 12.04
6.93 2.60 45.80 92.53 11.71
7.68 2.70 47.11 91.64 11.69
8.43 2.80 48.68 91.31 11.82
9.18 2.90 50.37 91.23 11.74
9.95 3.00 51.69 90.49 11.79
10.71 3.10 53.59 90.80 11.82
11.46 3.20 55.84 91.65 11.91
12.20 3.30 58.45 93.02 12.33
12.98 3.40 60.89 94.05 12.33
13.40 3.50 62.50 94.13 12.17
14.38 3.60 66.31 96.74 11.95
15.10 3.70 68.15 96.74 12.06
15.88 3.80 70.26 97.11 12.16
16.51 3.90 73.62 99.15 12.24
17.20 4.00 76.60 100.57 12.35
17.90 4.10 77.95 99.86 12.21
18.60 4.20 78.93 98.70 12.12
19.29 4.30 80.56 98.39 12.16
20.02 4.40 82.43 98.39 12.24
20.71 4.50 83.86 97.87 12.29
21.44 4.60 86.06 98.26 12.20
22.16 4.70 87.22 97.46 12.22
22.88 4.80 89.28 97.69 12.30
23.60 4.90 90.73 97.25 12.35
24.33 5.00 93.11 97.80 12.31
25.06 5.10 94.49 97.31 12.25
25.78 5.20 96.40 97.37 12.33
26.51 5.30 97.90 97.02 12.40
27.25 5.40 99.20 96.48 12.61
28.00 5.50 99.22 94.75 12.92
28.77 5.60 99.45 93.27 13.29
29.57 5.70 98.75 90.99 13.62
30.37 5.80 99.30 89.92 13.89
31.19 5.90 98.67 87.83 14.11
32.05 6.00 97.61 85.44 14.29
--------- --------- --------- --------- ---------
MAX: 32.05 6.00 99.45 100.57 14.89
MIN: 0.69 1.80 26.43 77.12 10.00
--------------------------------------------------------------------------------
Dynojet Research Inc.
Run Name: C:\DynoRuns\Toyota\2012 Toyota Yaris Greg Mamishian\RunFile_003.drf
Run Title: 2012 Toyota Yaris Greg Mamishian
Run Notes: Weapon R Intake
BLOX Velocity Stack Air Filter
Weapon R 4-2-1 Header
Micro Image MagnaFlow Exhaust
Run Date: 7/5/2012 12:22:20 PM
RunFile_003.drf: 80.12 °F 29.20 in-Hg Humidity: 41 % SAE: 1.02 Average Gear Ratio: 52.46
s RPM x1000 hp ft-lbs Air/Fuel
0.75 2.50 44.23 92.92 12.69
1.49 2.60 45.99 92.90 12.16
2.24 2.70 47.27 91.96 12.03
2.99 2.80 48.95 91.82 12.04
3.75 2.90 50.38 91.24 12.06
4.50 3.00 51.93 90.91 12.04
5.27 3.10 53.56 90.74 11.95
6.02 3.20 55.65 91.34 12.08
6.77 3.30 58.54 93.17 12.54
7.50 3.40 61.18 94.50 12.52
8.22 3.50 63.54 95.35 12.25
8.94 3.60 66.56 97.11 12.02
9.65 3.70 68.05 96.60 12.07
10.37 3.80 70.09 96.87 12.37
11.07 3.90 73.58 99.09 12.48
11.76 4.00 76.68 100.68 12.56
12.45 4.10 78.78 100.92 12.32
13.15 4.20 79.58 99.52 12.33
13.83 4.30 81.10 99.05 12.32
14.56 4.40 83.05 99.13 12.35
15.27 4.50 84.57 98.71 12.26
15.98 4.60 86.14 98.35 12.18
16.69 4.70 87.84 98.16 12.29
17.41 4.80 89.39 97.81 12.31
18.14 4.90 90.94 97.47 12.22
18.86 5.00 92.20 96.85 12.13
19.59 5.10 94.17 96.97 12.15
20.32 5.20 96.37 97.34 12.17
21.05 5.30 97.80 96.92 11.96
21.79 5.40 98.64 95.94 11.96
22.55 5.50 99.23 94.76 11.93
23.32 5.60 99.72 93.53 11.97
24.11 5.70 98.34 90.61 11.89
24.92 5.80 98.45 89.15 11.78
25.75 5.90 98.30 87.51 11.76
26.60 6.00 98.02 85.80 11.94
--------- --------- --------- --------- ---------
MAX: 26.60 6.00 99.72 100.92 12.69
MIN: 0.75 2.50 44.23 85.80 11.76
maybe you could overlay the two dyno runs if your dyno guy keeps the files (I assume he would)This is where I'm still at...
I like the progress you are making. it may be advantageous for you to go to a muffler shop and get them to replace that run of 1.75" pipe with 2"...obviously not until you get the intake manifold experiment done.
when you get the manifold done, we definitely need some pics of the final product also.
Picture not included in this copy
With the short ram completed and the baseline dyno done, everything is now waiting on the CNC guys to punch out the head flange and throttle body adapter. Then I go the welder to get the flange put on. Then I get the whole thing sandblasted. 🙂
that's beautiful. excel can be your friend. that will show you the advantages and disadvantages to your intake manifold.
you have quite the project going here. now I am chompin at the bit for more.
you have quite the project going here. now I am chompin at the bit for more.
Originally Posted by malibuguy ↑Stock air box...removed carbon filter and im running an Apex-i drop in replacement filter. I made a full custom 2" mandrelbent exhaust. I also have amsoil synthetic trans and engine oil. Also i have a weaponr header too
FWIW, I ran 106whp/107wtq with intake, 2.25" crush bent resonator-axle section and a Megan axleback .....no headerOriginally Posted by tooter ↑Ah, there's where you got those extra horses. 🙂
Since I have a header and an axleback, that bigest gain is found in the midpipe. 👍
Dyno's vary and can really only be relied on comparisons to personal runs....or if a stock yaris runs on the same day. That said, 100whp with the wimpy stock 1.75" midpipe makes sense...