Yarisworld Archive

Yaris Dyno charts

260 posts · 848,025 views · page 1 of 6

eTiMaGoOriginal postBangkok, Thailand · Nov 4, 2008#1
If you've taken your Yaris on a Dyno, post the results here, along with a list of relevant mods 🙂

To start off, here's one by staticorex, bone stock.

1 attachment not included in this copy

Replies 259

YodaFL · Nov 4, 2008#2
kool cant wait to see the results
LtNoogieWest Hills, CA · Nov 4, 2008#3
Originally Posted by eTiMaGo ↑
If you've taken your Yaris on a Dyno, post the results here, along with a list of relevant mods 🙂

To start off, here's one by staticorex, bone stock.
Was it a manual or AT?
MasteraalSydney Australia · Nov 5, 2008#5
5400-6100 not much difference in power output lol
cali yarisCanoga Park, CA · Nov 6, 2008#6
Here is mine with intake, header, pulleys and axle-back exhaust:

Picture not included in this copy
cali yarisCanoga Park, CA · Nov 6, 2008#7
And here is mine with the turbo set up on stock motor @ 8psi,
along with a different pull from the dyno session shown before:

Picture not included in this copy
cleongSingapore · Nov 6, 2008#8
Here's mine:

DC Header, Fujitsubo Exhaust, Denso Iridium Spark Plugs, 5W40 Shell Helix Oil. Otherwise everything is as standard factory delivered.

Numbers on the chart are at the crank. WHP is roughly 102.75 and torque is 130Nm (95.8ft/lb).
EDIT: Thanks for pointing out the unit difference for torque; I have added the lb/ft conversion.

Picture not included in this copy
taKutoToronto · Nov 6, 2008#9
that's because yours is measured in Nm :P everyone else is ft-lbs.
not a yaris but same engine anyways, only mods are intake and muffler replaced with a small resonator.
edit: manual transmission, did all runs in 4th gear

1 attachment not included in this copy

YodaFL · Nov 6, 2008#10
this will be a very useful thread
+1
cali yarisCanoga Park, CA · Nov 6, 2008#11
cleong, you're hp and torque don't cross at 5250 -- sup with that?

also, wouldn't the rev limiter kick in at 6250?
Or do you not have the same limit as we do in USDM?
at3GGVA Beach · Nov 6, 2008#12
Is it all dynos charts that should cross at 5250...or is that just a correct setup for our engines?
cleongSingapore · Nov 6, 2008#13
Originally Posted by cali yaris ↑
cleong, you're hp and torque don't cross at 5250 -- sup with that?

also, wouldn't the rev limiter kick in at 6250?
Or do you not have the same limit as we do in USDM?
I posted this chart before the Big Crash and someone explained its because the scale between HP and torque is different.

Your NA dyno chart seems to go to 6500rpm too. But redline's 6500rpm on my dashboard, I think. I'll need to run out and check it later.
LtNoogieWest Hills, CA · Nov 7, 2008#14
Had to straight-line interpolate where the sensor had a bad connection.

Not as good as I had hoped. This was my baseline before the supercharger install.

1 attachment not included in this copy

richardholdenerLas vegas, NV · Nov 13, 2008#15
HP and tq are alwasy equal at 5252 rpm. The reaosn they don't cross on the graph is that the two scales are different. If both HP and NM (converted to tq) scales went from 0-160, then they would cross at 5252. Here is the 120-hp graph supplied previously before the hack. Mods were custom intake manifold, CAI, Xd tb, synthetic oil and off-road down pipe with no exhaust.
Originally Posted by at3GG ↑
Is it all dynos charts that should cross at 5250...or is that just a correct setup for our engines?
Originally Posted by at3GG ↑
Is it all dynos charts that should cross at 5250...or is that just a correct setup for our engines?

1 attachment not included in this copy

TreyzLong Island, NY · Nov 13, 2008#16
Now are these all with manual transmissions?
eTiMaGoThread starterBangkok, Thailand · Nov 13, 2008#17
I would think so yeah... I have seen local dynos of stock AT's here doing about 80whp only...
TreyzLong Island, NY · Nov 13, 2008#18
Yeah .. I got the Yaris purposely as a daily driver since I had my 240SX track/weekend driver so bought it in an atomatic.

Man am I kicking myself in the ass now after I got rid of the NIssan and started modifying the Yaris.
cleongSingapore · Nov 14, 2008#19
LtNoogie's got an automatic. I think the rest are all manual transmissions.
richardholdenerLas vegas, NV · Nov 18, 2008#20
Here is a graph of our recent test using a CAI (actually flipped over stock filter lid), the new intake manifold, long-tube header and 2.25-inch exhaust, NST u-pulleys & Xd Tb. Might be more with additional tuning once FIC arrives from AEM for testing.

1 attachment not included in this copy

blacksandiegovitzJust chillin' out brah ! · Nov 18, 2008#21
Very impressive numbers with that NA set-up. More power than with the blitz supercharger kit , Very nice, I hope to make about the same as I'll be running the longtube header with the intake manifold.
eTiMaGoThread starterBangkok, Thailand · Nov 18, 2008#22
I, for one, can't wait to see Garm dyno his beast with the new intake manifold 😁
at3GGVA Beach · Nov 19, 2008#23
^^^🤤
whooppee777Maryland · Nov 20, 2008#24
the first graph is of staticorex (im assuming by the name of the file) his yaris is an automatic sedan. he has a blitz supercharger now he had his yaris dynoed after the install of the supercharger i've seen it in person cant remember the numbers though. i wanna say close to 130 with the blitz supercharger
PETERPOOPOahu · Dec 18, 2008#25
Originally Posted by blacksandiegovitz ↑
Very impressive numbers with that NA set-up. More power than with the blitz supercharger kit , Very nice, I hope to make about the same as I'll be running the longtube header with the intake manifold.

Actually with the blitz S/C kit and pulleys,exhaust,CAI, etc... it's been recorded to put down 130whp.

But I am with you. I am on his manifold list and possibly his long tube header list. I might run those for a year or two until a legit company comes out with a turbo kit for the yaris.
1nzBrunei · Jan 31, 2009#26
Sedan, Auto trans, both with trust airinx intake kit, from 98.4whp-101.6whp

When this car was just 15000km and just installed the trust with non branded, noisy aftermarket exhaust i got 102.8whp but this maybe because spark plug, intake and temperature which caused me to luse the 1.2whp hehe

Picture not included in this copy
cleongSingapore · Jan 31, 2009#27
The dyno sheet looks like it only has torque and AFR overlay, HP graph doesn't seem to be there?

What mods have you made to the car to get 101whp?
LtNoogieWest Hills, CA · Jan 31, 2009#28
Before: Max HP - 90.5 hp.... Max Torque - 88.6 ft-lb
After : Max HP - 117 hp..... Max Torque - 114 ft-lb

I'm also running too lean. The only other change besides the supercharger was that in the before run, I had the TRD CAI. I swapped that out for the aFe Intake for the after run.

The butt dyno says it feels like I have more power but the the bull stops with the charts.

Those of you in the Los Angeles area looking to see how much power your car really puts out should go see Harry at HK MotorSports. He also tunes cars for a living so if you get a turbo kit, perhaps he can help.

http://www.hkmotorsportsdynoshop.com/

1 attachment not included in this copy

PETERPOOPOahu · Jan 31, 2009#29
wow only 117 with full NST pulley set, blitz S/C, afe intake, megan header,AND trd exhaust.... how the heck did that other guy put down 130whp?
LtNoogieWest Hills, CA · Jan 31, 2009#30
I guess my slushbox is slushing all my power away. You guys with the manual transmissions have all the fun.

Actually, I'm not complaining because when I push hard on the pedal, the car just takes off like a monster was just let loose, and immediately. I don't know if the additional low-end torque is what's giving me better acceleration or what. I almost never go beyond 4,000 rpm so the max HP is something I'll never feel.
PETERPOOPOahu · Jan 31, 2009#31
Well a 27hp gain isn't bad, i was just expecting more (after hearing about 130whp from the other blitz owner).
thebarberGrand Rapids, MI · Jan 31, 2009#32
Originally Posted by PETERPOOP ↑
Well a 27hp gain isn't bad, i was just expecting more (after hearing about 130whp from the other blitz owner).
its the auto thats limiting his at-wheel HP

a manual with similar mods would run about 135whp

the only nst pulley that will yield wheel horsepower is the underdrive crank pulley.

the other items he has are good, but if he replaces the resonator to axle exhaust section im sure he'd gain a few more ponies

117 is very respectable for a s/c'd auto

well done LT
cleongSingapore · Jan 31, 2009#33
Phwoar, a slushbox wastes nearly 13-18hp compared to a stick? That's gotta hurt!
LtNoogieWest Hills, CA · Jan 31, 2009#34
Originally Posted by cleong ↑
Phwoar, a slushbox wastes nearly 13-18hp compared to a stick? That's gotta hurt!
It actually doesn't hurt that bad. Numbers and charts are abstract. My butt dyno knows the difference when I have the S/C running and when I don't. Since I don't have a MT, I don't have a frame of reference as to what I'm missing. Ignorance can be bliss. 👍
1nzBrunei · Feb 1, 2009#35
Originally Posted by cleong ↑
The dyno sheet looks like it only has torque and AFR overlay, HP graph doesn't seem to be there?

What mods have you made to the car to get 101whp?
Picture not included in this copy
just a trust intake, lukey exhaust and denso iridium spark plugs
PETERPOOPOahu · Feb 1, 2009#36
no blitz (even with all the mods noogie has) on a manual has been dyno'd at 135whp so far. just 130whp.
whiteghettoportland oregon · Feb 4, 2009#37
do we have a comparison of automatic 1.5, stock everything
CAI vs SRI?
PETERPOOPOahu · Feb 28, 2009#38
Picture not included in this copy

Done on a DynaPack dyno.

89.9whp

95.7 lbs of torque

MODS: octane 87. aFe intake, NST underdrive/wt/alt pulleys, blitz axleback, royal purple.
thebarberGrand Rapids, MI · Feb 28, 2009#39
peter, why didnt they run your car to redline....you'd have made more power...
PETERPOOPOahu · Feb 28, 2009#40
Because I don't know what the redline is. I told him 6100-6200rpms. It already sounded like the engine was going to blow up when i was next to the car. All the other dynos on this thread seem like their power peaks at 6k and dies after that. I don't think it would have made more power.
LtNoogieWest Hills, CA · Mar 1, 2009#41
What hp reading were you hoping for? I was hoping to do better than 90 hp for the "before" dyno pulls. I sure expected more than 117 hp for the "after" dyno pulls. It's sobering but I'm glad you did it. Congratulations.
PETERPOOPOahu · Mar 1, 2009#42
Thanks. I was hoping for ATLEAST 90whp. I probably would have had it if i was running 91, had a header, and it was cooler here in hawaii.

I am hoping for some big gains once I put everything on!
changchewsoonMalaysia · Apr 1, 2009#43
Here's mine:

Picture not included in this copy
PETERPOOPOahu · Apr 12, 2009#45
Picture not included in this copy

Running lean. They gauged the AFR from the exhaust tip. Will update when I get my Wideband AF gauge on.
kngrsllSpartanburg, SC · May 10, 2009#46
Completely stock dyno at @56k miles. Only oil changes and one filter change at 30k.

Picture not included in this copy

With 20% correction, it was 105.5 hp. The engine has held up very well! Thai said with new plugs and air filter, it would easily gain a few hp too.
LtNoogieWest Hills, CA · May 16, 2009#47
Originally Posted by kngrsll ↑
Completely stock dyno at @56k miles. Only oil changes and one filter change at 30k.

With 20% correction, it was 105.5 hp. The engine has held up very well! Thai said with new plugs and air filter, it would easily gain a few hp too.
Manual or AT?
LtNoogieWest Hills, CA · May 16, 2009#48
Originally Posted by The Spectacle ↑
Custom cat back exhaust, otherwise stock. This thing runs PIG rich from the factory!

Link to dyno: http://www.youtube.com/watch?v=kuryS8r_yGo
Nice video. Those dyno guys should have let your engine bay cool off a little between runs. And yes, that seems really rich.
GiupoItaly · May 26, 2009#49
Hi guys,
This is my Dyno chart at 0.8 bar of boost , I have made the test in a very hot day 30°C (86°F) with 65% humidity also I have also tuned with 0.9 bar of boost and the results are 206 hp and 239.6 Nm torque

Picture not included in this copy
TreyzLong Island, NY · May 30, 2009#50
Originally Posted by kngrsll ↑
Completely stock dyno at @56k miles. Only oil changes and one filter change at 30k.

With 20% correction, it was 105.5 hp. The engine has held up very well! Thai said with new plugs and air filter, it would easily gain a few hp too.
No way that there is a 20% on that last sheet for a stock Yaris. For crank yes but not wheel so it is correct in terms of wheel hp being at 88whp.