Yarisworld Archive

tooter's manifold adventure...

1,454 posts · 559,522 views · page 3 of 30

Replies continued

bladesmith6PA · Jun 23, 2012#101
I have that setup already but you might have to trim the velocity stack and weapon R tube a little bit for a proper fit next to the headlight. It does make a difference and when you shift the thing is sucking so much air sounds like I have a blowoff valve(don't know why but i think it's pretty cool)
tooterThread starterLos Angeles · Jun 23, 2012#102
Cool! 🙂
Do you have a pic of your intake that you could post? ...or even a video of the sound? I'd love to hear it. 👍

If it's already loud on a stock manifold, I wonder what it's going to sound like on this? 😆
Picture not included in this copy
tooterThread starterLos Angeles · Jun 23, 2012#103
Found someon else's experience with a velocity stack intake...

We then fabricated a 3" intake with a BPI flow stack, and installed a motordyne 5/16" spacer. Huge gains were seen above 5500rpm, the largest gain being over 20whp near RPM limit. The peak power increased to 228whp, another 11whp from spacer + intake.

Picture not included in this copy

Here's what they look like without filters on them...

Picture not included in this copy

Picture not included in this copy

My setup will be quite similar to this, except with an airflow sensor...

Picture not included in this copy
tooterThread starterLos Angeles · Jun 23, 2012#104
This is a flow stack truck muffler...

Quiet Performance Straight Flow Stack Muffler


Item Number: 185828


Regular price: $194.99

Straight flow mufflers cancel out soundwaves by directing them into one another to absorb sound energy without added restriction. Up to 50 additional horsepower, improved throttle response and lower exhaust gas temperatures. Improves fuel mileage and power. 51.5" total length x 10" diameter. Designed to go up the side or rear of the cab. This muffler creates no back pressure, which allows for a gain of at least 1 mile per gallon. You can save 1000 gallons for every 100,000 miles driven. Since the flow is not restricted, the muffler gathers no soot or condensation, making this muffler last for the life of the truck. 5" I.D. inlet and outlet. Fits all class 8 trucks with 5" vertical stacks.
Sold individually.


Picture not included in this copy

It flows from bottom to top with the flow stack above the gap in the baffle. Really clever design.
muffin_topMidwest · Jun 23, 2012#105
Originally Posted by tooter ↑
This is a flow stack truck muffler...

Quiet Performance Straight Flow Stack Muffler


Item Number: 185828


Regular price: $194.99

Straight flow mufflers cancel out soundwaves by directing them into one another to absorb sound energy without added restriction. Up to 50 additional horsepower, improved throttle response and lower exhaust gas temperatures. Improves fuel mileage and power. 51.5" total length x 10" diameter. Designed to go up the side or rear of the cab. This muffler creates no back pressure, which allows for a gain of at least 1 mile per gallon. You can save 1000 gallons for every 100,000 miles driven. Since the flow is not restricted, the muffler gathers no soot or condensation, making this muffler last for the life of the truck. 5" I.D. inlet and outlet. Fits all class 8 trucks with 5" vertical stacks.
Sold individually.


Picture not included in this copy

It flows from bottom to top with the flow stack above the gap in the baffle. Really clever design.
That should look mighty scary underneath your car. 10" diamater may challenge your ability to lower the vehicle though.. 🤷 😛

I have several of those 1ZZ intakes at work, they look seriously cool. Hoping this makes power on the cheap, if so, I'm in!
tooterThread starterLos Angeles · Jun 23, 2012#106
We'll find out soon... 🙂

So far, the guys are working on the flange and throttle body adapter drawings. The aluminium will arrive any day now. And when the flow stack intake is delivered on the 28th, I'll be ready for a baseline dyno test. I want to have a test with everything else already on the car, so that the manifold is the only component changed. 👍
malibuguyWestminster, MD · Jun 24, 2012#107
The weaponR filter has a small velocity stack built into it...

Do you want to sell it...?
fnkngrvIn The Hotbox · Jun 24, 2012#108
It would be nice if you would be willing to provide all dimensions for that Blox setup. It could be a great component depending on physical dimensions for my turbo installation especially if they provide the type of air flow performance that is touted.
tooterThread starterLos Angeles · Jun 24, 2012#109
Originally Posted by malibuguy ↑
The weaponR filter has a small velocity stack built into it...

Do you want to sell it...?
Sure. 🙂

It's brand new in the box, and can be yours as a complete kit for $20 and 7$ for USPS Priority Mail shipping.

Edit: Price lowered. It's likely you wanted the cylinder filter and not the cone filter so I went ahead and listed it on Ebay. If you do want it, you can have it for $20 if you let me know before anyone bids on it so i can cancel the auction.

Filter
3" to 2.5" silicone adapter
All stainless steel screw clamp
Allen wrench to disassemble filter for cleaning
Element cleaning solution

Picture not included in this copy

The filter has a really tough ridgid metal mesh on the outside and inside of the element...

Picture not included in this copy

It's built for a 3 inch intake and has internal vanes to smooth the airflow...

Picture not included in this copy

The silicone adapter allows it to fit a 2.5 inch intake...

Picture not included in this copy

Picture not included in this copy
tooterThread starterLos Angeles · Jun 24, 2012#110
Originally Posted by fnkngrv ↑
It would be nice if you would be willing to provide all dimensions for that Blox setup. It could be a great component depending on physical dimensions for my turbo installation especially if they provide the type of air flow performance that is touted.
Sure. Be happy to. 🙂 It arrives this Thursday the 28th. From the installation pics I've seen, a lot of them are turbos like this for example.

Picture not included in this copy

1 attachment not included in this copy

GolddeenohColumbia, SC · Jun 24, 2012#111
I was experimenting a few years ago with the Spectre Filters (inward facing cone/ no oil) that you get from Advanced Auto Parts and the short period of time that it was on there it sounded really mean. I don't Know how much better it would sound with my AEM cold Air intake but I might try it out again(this time with a real Intake pipe to connect to). It sounded like it rev'd up higher and louder when I had tried it out but that could have just been the sound it made and not what it actually did. I don't know what the feeling to these filter are but It may be cheaper or an easy replacement for future use.

Picture not included in this copy
tooterThread starterLos Angeles · Jun 24, 2012#112
That's a really good design because it has at least another third more filter surface area on the inside. They're an oiled filter, and come in 3, 3.5, and 4 inch openings so some adaption would be needed to make them fit a yaris intake tube.

I had a go on the manifold with some sandpaper just to see how well the surfaces would clean up...

Picture not included in this copy

Not too bad as a raw finish, except up close there are too many little pits, nicks, and flaws, so it will likely end up being painted.
malibuguyWestminster, MD · Jun 26, 2012#113
Damn i thought you got the SecretWeapon intake. I really like the SW filter. The dragon is good stuff...just not my style.
cali yarisCanoga Park, CA · Jun 26, 2012#114
so it will likely end up being painted.
or powdercoated, or even better yet, ceramic coated. Good cheap place in LA for that. 👍
tooterThread starterLos Angeles · Jun 27, 2012#115
Originally Posted by malibuguy ↑
Damn i thought you got the SecretWeapon intake. I really like the SW filter. The dragon is good stuff...just not my style.
No problem, guy... 🙂
I figured that, because it's certainly not my style either. I was just bought it for the intake tube. The Dragon is the cheapest one and uses exactly the same intake as the Secret Weapon which costs $40 more. So I spent that money on the BLOX velocity stack dry filter instead. Putting them together makes a really neato intake for $224.👍

I'll post some pics when I put the parts together.
tooterThread starterLos Angeles · Jun 27, 2012#116
Originally Posted by cali yaris ↑
or powdercoated, or even better yet, ceramic coated. Good cheap place in LA for that. 👍
Hey Garm, 🙂

I knew nothing about Ceramic coatings and needed to go read up on it. Some coating businesses recommended not doing it on old aluminium because of the 1,300degree high heat. They mentioned the possibility of warping and the metal outgassing. One auto forum poster warned not to coat the inside of intake manifold runners in case any of the coating was to flake and get run through the engine.

Has your ceramic experience been different? Are there any advantages? Any drawbacks that you know about? I have no idea if what I'm reading on the internet is true or not. But since I don't want to take any unnecessary chances, its more likely I'll go with powdercoating as it sounds safer. The manifold is only exposed to mild tempratures anyways so maybe ceramic isn't necessary.
tooterThread starterLos Angeles · Jun 27, 2012#117
Originally Posted by tooter ↑
Sure. 🙂

It's brand new in the box, and can be yours as a complete kit for $20 and 7$ for USPS Priority Mail shipping.

Edit: Price lowered. It's likely you wanted the cylinder filter and not the cone filter so I went ahead and listed it on Ebay. If you do want it, you can have it for $20 if you let me know before anyone bids on it so i can cancel the auction.

Filter
3" to 2.5" silicone adapter
All stainless steel screw clamp
Allen wrench to disassemble filter for cleaning
Element cleaning solution

Picture not included in this copy

The filter has a really tough ridgid metal mesh on the outside and inside of the element...

Picture not included in this copy

It's built for a 3 inch intake and has internal vanes to smooth the airflow...

Picture not included in this copy

The silicone adapter allows it to fit a 2.5 inch intake...

Picture not included in this copy

Picture not included in this copy

The air filter sold on Ebay for $25. That brings the cost of the intake down to just $200. 👍
tooterThread starterLos Angeles · Jun 28, 2012#118
The BLOX velocity stack air filter arrived today. 🙂
It fits perfectly on the Weapon R intake tube...

Picture not included in this copy

The throat of the velocity stack is 2.5 inches... and smothly flares out to 6 inches...

Picture not included in this copy

...and the oversized dry element filter is 7.5 inches in diameter.



Picture not included in this copy

Hope it fits under the hood! 😆


Picture not included in this copy

Now, to put it on the car. 🙂
07typeSSouthern California · Jun 28, 2012#119
daaaannnggg thats a big filter haha. I know you said the diamter is 7.5 inches, whats the length? Looks to be fairly close to the diamter measurement..
tooterThread starterLos Angeles · Jun 28, 2012#120
Yeah, it's a big ass filter all right!😆

It's 7 inches long. I discovered that this filter is exactly the same one used on the big 4 inch intakes, which I think is great. If it has the flow capacity to handle a 4 inch intake, it'll flow really good on a 2.5. 🙂

I really like the fact that the BLOX is a dry element filter so I don't need to mess with oil. Besides costing a lot more, it was why I didn't get the K&N Typhoon short ram kit.

And the fact that the velocity stack outer diameters are 6 inches regardless of throat diameter, it makes this particular stack really large with such a small 2.5 inch throat on it.

Right now, I'm cutting the intake pipe little by little until the whole assembly is short enough to fit. It won't take much, likely about an inch all totaled. The diameter is totally fine as the stock airbox is fat. Man, does it fill up that space!. 😆
fnkngrvIn The Hotbox · Jun 28, 2012#121
well for my purposes with my current turbo setup that filter wouldn't work :( It is MUCH too big. I was rubbing on my harness with the K&N 6" just co clear my hood. Wonder how much of an issue it would be to use my AFE Pro Dry and retrofit it on?
tooterThread starterLos Angeles · Jun 29, 2012#122
Originally Posted by fnkngrv ↑
well for my purposes with my current turbo setup that filter wouldn't work :( It is MUCH too big. I was rubbing on my harness with the K&N 6" just co clear my hood. Wonder how much of an issue it would be to use my AFE Pro Dry and retrofit it on?
I don't think a 6 inch filter will work, as just the diameter of the velocity stack alone is already 6 inches...

Picture not included in this copy

I got the filter on this evening... 🙂 and ended cutting about 4 inches off the intake pipe so now it's a really short ram intake... 😉

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Drove it to town to gas up and reset the mileage. I don't think it actually made any big difference but I've only driven it just a few miles. I had expected there to be some intake noise, but it's pleasantly quiet. I'm not sure, but it might be because of the really smooth direct flow pattern, or maybe because the filter is so large. Overall, I'm pleased how it turned out, a simple direct almost straight true velocity stack short ram intake that flows well. The car runs great, and no check engine light...

...and it looks really COOL. 🙂
tooterThread starterLos Angeles · Jun 29, 2012#123
With the intake completed, and over 1,000 miles on the engine, the car is ready for a baseline dyno this coming week... 🙂

Picture not included in this copy

It will be done with:

Weapon R short ram intake with BLOX velocity stack air filter
Weapon R 4-2-1 tri-y header
Micro Image MagnaFlow Center Exit exhaust
BEEFnorth carolina · Jun 29, 2012#124
that filter is huge in the engine compartment. it does look nice and filled though. a lot of the aftermarket intakes make it look like there is something missing there.

can't wait to see your baseline numbers. how is the actual intake manifold coming along? any pics of its progress?
tooterThread starterLos Angeles · Jun 29, 2012#125
With that way oversized filter, it's almost like having an open intake because there's hardly any flow restriction. I'm still suprized at how super quiet it is. There's almost no difference in sound from the stock air box.

My two week timeline was wildly optimistic... 🙄

They have all the aluminium stock and the 3D drawings are still being worked on. One of the guys is in the hospital for an appendix operation, so the project got held up while he recovers. I'll be there next week to go over the computer drawings with them before machining begins.
tk-421Dagobah · Jun 29, 2012#126
That cone filter fills that space really well. 👍
Still got an OEM throttle body? You may want to swap it out for a compatible one that is perhaps less restrictive... 2¢
07typeSSouthern California · Jun 29, 2012#127
You know you've done things right when your air filter is almost as large as your battery haha..

And Id have to imagine that the size of the filter definitely played a part in the sound.. I know when I went from the Dragon set up to a k&n with a little more surface area, it had a deeper growl.. It was definitely a pleasant surprise..
bladesmith6PA · Jun 29, 2012#128
Yeah I mentioned that you were going to have to cut your intake pipe down, I had to do the same thing with mine. I do think that the larger filter has added just a bit more growl though especially since I still have the stock muffler( i need to do something about that) I think it pulls harder now but maybe that is just in my head.
tooterThread starterLos Angeles · Jun 29, 2012#129
Originally Posted by tk-421 ↑
That cone filter fills that space really well. 👍
Still got an OEM throttle body? You may want to swap it out for a compatible one that is perhaps less restrictive... 2¢
I'm happy with the stock one as I'm more of an economy driver than a high performance guy. Although it's lots of fun experimenting with flow design, both my wife and I basically drive the car like it's stock. 🙂
tooterThread starterLos Angeles · Jun 29, 2012#130
Originally Posted by 07typeS ↑
You know you've done things right when your air filter is almost as large as your battery haha..

And Id have to imagine that the size of the filter definitely played a part in the sound.. I know when I went from the Dragon set up to a k&n with a little more surface area, it had a deeper growl.. It was definitely a pleasant surprise..
This one has no growl at all, and I'm not really sure why. There's sure no lack of filter surface area as that same filter will flow a big block V8 with a 4 inch intake! 😆

I'm wondering if it is the really large super smooth velocity stack. I'll have to try making a video of the engine running with the stack alone just to find out. The filter element pops right off and on with just one simple screwband, while leaving everything else in place. That's what I really like about the design. Cleaning the filter will be a snap, and the element makes a perfect seal with the stack.
tooterThread starterLos Angeles · Jun 29, 2012#131
Originally Posted by bladesmith6 ↑
Yeah I mentioned that you were going to have to cut your intake pipe down, I had to do the same thing with mine. I do think that the larger filter has added just a bit more growl though especially since I still have the stock muffler( i need to do something about that) I think it pulls harder now but maybe that is just in my head.
Yeah, reality set in quickly the minute I stuck the filter under the hood. My exhaust already growls so I can't tell! 😆

Basically half of the 90 degree on the intake is chopped off. I was concerned about the super short distance from the filter intake to the MAF sensor setting off the check engine light. But it's working perfectly fine. 🙂 It's possible that the large smooth taper on the velocity stack isn't introducing any turbulence, so the MAF sensor is getting undisturbed readings even being just a few inches away.

Can't wait to do a dyno run. The engine is basically stock so the numbers will be unimpressive to be sure, but what I'm more interested in is the relative difference between the stock manifold and my craazy homemade concoction. 😉

Oh, and I'll be sure to do videos of the dyno runs! 🙂
tk-421Dagobah · Jun 29, 2012#132
Originally Posted by tooter ↑
I'm happy with the stock one as I'm more of an economy driver than a high performance guy. Although it's lots of fun experimenting with flow design, both my wife and I basically drive the car like it's stock. 🙂
Something tells me the newly added growl will inexplicably make your feet heavier... 😁
Your setup is very close to what I want to do with my car, so you bet I'll be watching that dyno chart very closely regardless of our different driving style/conditions.
tooterThread starterLos Angeles · Jun 30, 2012#133
Originally Posted by tk-421 ↑
Something tells me the newly added growl will inexplicably make your feet heavier... 😁
I did drive 100 freeway miles today to make sure the engine was broken in enough for the dyno runs next week. Lots of 70 to 80+ mph. Flat out runs, one made it to 97mph. Let's face it, these cars are gutless! 😆 You can put your foot to the floor and time the acceleration with a calendar. The car exhaust sounds great, but nothing much is actually happening. I ride a motorcycle so I'm spoiled for performance.

What did suprize me is that the average mileage for the trip, even with half of it very heavy footed driving, was still an excellent 39.9 mpg. 🙂

Your setup is very close to what I want to do with my car, so you bet I'll be watching that dyno chart very closely regardless of our different driving style/conditions.
As will I. 🙂
This dyno is just for the baseline so it won't be very exciting. I expect about 90 to 92WHP tops...

...and hope that the second set of runs are better than the first. 😉
cali yarisCanoga Park, CA · Jun 30, 2012#134
90-92 would mean no gains, or even a bit of a loss, from existing "baseline" mods.
BEEFnorth carolina · Jun 30, 2012#135
I am hoping that your dyno will be 100-105 as you have an intake, axle back, and header. this is similar to where I plan to end up as well. hopefully in about 2 months or so.

very interested in the intake manifold and what gains you see.
tooterThread starterLos Angeles · Jun 30, 2012#136
Originally Posted by cali yaris ↑
90-92 would mean no gains, or even a bit of a loss, from existing "baseline" mods.
Well, it sure ~feels~ like it only has 90 to 92 horsepower. 😆

But that's not a complaint, just an observation. I've always owned little cheap fun economy cars, because that's what I like to drive. 👍
tooterThread starterLos Angeles · Jun 30, 2012#137
Originally Posted by BEEF ↑
I am hoping that your dyno will be 100-105 as you have an intake, axle back, and header. this is similar to where I plan to end up as well. hopefully in about 2 months or so.
I'll find out this week. That's the fun of this... finding out. 🙂

very interested in the intake manifold and what gains you see.
Same here. The bling factor is far more likely to exceed the performance factor. 😆
Bluevitz-rsOshawa, Ontario, Canada · Jun 30, 2012#138
The slow car feeling is in the weight. Putting the car on a diet makes a big difference.
GolddeenohColumbia, SC · Jun 30, 2012#139
^ agreed, my car hit 117mph like a little champ the other day (coming to the top of 4th gear) and that was before taking the seats out. And after the seats are out it feels lighter and a little quicker. But I have also changed out to Royal Purple performance motor oil, E3 spark plugs and have 36k miles on it so it is well broken in, plus the signature mods listed below. I'm hoping to have that magical 107whp but I will need to take it to a dyno to be sure of that.
1.5Tampa · Jun 30, 2012#140
Hell yeah gutted out makes a huge difference. I took out close to 100 lbs of interior
malibuguyWestminster, MD · Jun 30, 2012#141
My sedan gets to over 100mph with not much effort...
tooterThread starterLos Angeles · Jun 30, 2012#142
I have to admit that the 97 was on an upgrade. I do believe that it could do 100 on the flat... if I had enough time to get there. 😆
cali yarisCanoga Park, CA · Jun 30, 2012#143
I wonder what my 0-100 is... 😁
tooterThread starterLos Angeles · Jun 30, 2012#144
Originally Posted by cali yaris ↑
I wonder what my 0-100 is... 😁
I use a calendar to time mine... 😉

Do you have any tips for making a good accurate dyno run? What's the best tire pressure for the rollers?
cali yarisCanoga Park, CA · Jun 30, 2012#145
In terms of prep, dyno it like you drive it for the most accurate result.

You might write down a few things to compare to future dynos, ambient air temp, humidity, tire pressure, what fuel is in the car, etc.
tooterThread starterLos Angeles · Jun 30, 2012#146
I will... just normal 87 gas 40 psi in the tires and no other changes so that the conditions will be as similar as possible between the two sets of runs. 👍
tooterThread starterLos Angeles · Jun 30, 2012#147
Some pics with the air filter removed...

Picture not included in this copy

You can see how close the throttle body and MAF sensor are to the stack.
Picture not included in this copy

And heres a video of the engine running...

http://www.youtube.com/watch?v=JQt2uJ7PYfQ

There's not much intake noise even with the camera stuck up close. In the beginning the ECU was fishing around for an idle mixture trying to adjust to the open intake, but found its equilibrium by the end of the video.
cali yarisCanoga Park, CA · Jul 2, 2012#149
^ wow.

TRD Exhaust Manifold Header IST bB Vitz Corolla

Was: $ 1,086.96 Sale: $ 869.57
suckerfaceMilwaukee, WI · Jul 2, 2012#150
They have some great stuff on there, but you're certainly paying a premium for it. Just a shot in the dark, but I'm guessing the MI prototype will come in well under $800, right?