Yarisworld Archive

tooter's manifold adventure...

1,454 posts · 559,522 views · page 16 of 30

Replies continued

thebarberGrand Rapids, MI · Aug 24, 2012#751
tooter, once you get a bigger resonator-to-axleback exhaust piece, youll likely feel better gains all over
tooterThread starterLos Angeles · Aug 24, 2012#752
Originally Posted by 4/20 NEVER FORGET ↑
Time to have the shop make you a adapter for a corolla TB :)
The CNC guys at Origin Design can make an adaptor for any throttle body. How is the Corolla throttle body configured differently from the Yaris one?
cali yarisCanoga Park, CA · Aug 24, 2012#753
It bolts right on, it has a little larger throat.
Bluevitz-rsOshawa, Ontario, Canada · Aug 24, 2012#754
It has a bigger opening, nothing more. same bolt pattern, it's a direct bolt on. You'd just need a bigger opening on the adapter
Bluevitz-rsOshawa, Ontario, Canada · Aug 24, 2012#755
Originally Posted by cali yaris ↑
It bolts right on, it has a little larger throat.
you beat me to it LOL
tooterThread starterLos Angeles · Aug 24, 2012#756
Originally Posted by thebarber ↑
tooter, once you get a bigger resonator-to-axleback exhaust piece, youll likely feel better gains all over
That's one of the next steps... also a longer intake. 👍
Bluevitz-rsOshawa, Ontario, Canada · Aug 24, 2012#757
Finally got a picture of my valve cover. Had to clean it up first...
Picture not included in this copy
WeeYariGeorgetown, Ontario, Canada · Aug 24, 2012#758
^ shit that's a lot of rubbing! The tooter would compliment that nicely.
Bluevitz-rsOshawa, Ontario, Canada · Aug 24, 2012#759
Yeah a nice polished one :D
tooterThread starterLos Angeles · Aug 24, 2012#760
Originally Posted by Bluevitz-rs ↑
It has a bigger opening, nothing more. same bolt pattern, it's a direct bolt on. You'd just need a bigger opening on the adapter
Really? The tooter adaptor gradually transitions to the slightly smaller stock yaris throttle body diameter from the larger Corolla diameter. since all of the other CNC information is exactly the same, it would be a simple matter to just make one with a straight through bore.

Is the Corolla throttle body also drive by wire? If so, is the electrical plug compatable?
Bluevitz-rsOshawa, Ontario, Canada · Aug 24, 2012#761
Plug and Play.

Only issues I've read about are ppl needing to swap the chip on it from the one on the yaris. But others have just slapped it on, readjust the throttle plate idle screw and go.
tooterThread starterLos Angeles · Aug 24, 2012#762
Originally Posted by Bluevitz-rs ↑
Finally got a picture of my valve cover. Had to clean it up first...
Picture not included in this copy
That's awesome, blue! 👍

"Black plastic covers? We don need no stinking covers!"
Picture not included in this copy
Bluevitz-rsOshawa, Ontario, Canada · Aug 24, 2012#763
If you do decide to polish and cut the nubs off, this is actually a Prius valve cover. I discovered the nubs on the rear are hollow and had a hole in it so had to replace it. The Prius uses those rear ones to hold something.
tooterThread starterLos Angeles · Aug 24, 2012#764
Originally Posted by Bluevitz-rs ↑
Plug and Play.

Only issues I've read about are ppl needing to swap the chip on it from the one on the yaris. But others have just slapped it on, readjust the throttle plate idle screw and go.
"Reheheheeealy!"

Picture not included in this copy
bladesmith6PA · Aug 24, 2012#765
Can't be said enough, mad props for finishing the project in such a short time. Better than that asshat Holdener....
Jason@SportsCarDebary, FL · Aug 24, 2012#766
Originally Posted by tooter ↑
That's one of the next steps... also a longer intake. 👍
You can keep tossing parts at it, but until you can tune it you are not going to see the big gains.
b20vtegmaricopa, az · Aug 24, 2012#767
Originally Posted by Jason@SportsCar ↑
You can keep tossing parts at it, but until you can tune it you are not going to see the big gains.
this. and also, bolt-ons for such a low powered motor are kinda pointless imo... i'm new to the yaris and toyotas in general, but in honda land, if you wanna make big power, start with the head.
tooterThread starterLos Angeles · Aug 24, 2012#768
Originally Posted by bladesmith6 ↑
Can't be said enough, mad props for finishing the project in such a short time. Better than that asshat Holdener....
Thanks...🙂 I willingly chose to risk my own time and money just to find out for myself what would happen.

This is only a wild guess from reading the Holdener thread because I was really curious how that would all play out... but Richard's manifold might have yielded similar dyno results to mine which also produced an unsaleable product. That could have been why he pulled the plug on it even though he had $695 purchase orders for it.
suckerfaceMilwaukee, WI · Aug 24, 2012#769
Originally Posted by tooter ↑
"Reheheheeealy!"

Picture not included in this copy
That's about 80% true. If you get the 1ZZ TB whose part number ends in 031, you won't need to do the chip swap, just have the ECU re-learn the intake volume. At worst, you'll have a slightly higher idle until the engine warms up. This is what I'm dealing with, and don't mind, but I know thebarber took his off because of the same problem.
4/20 NEVER FORGETPortland, OR · Aug 24, 2012#770
From reading I've done on this forum, a couple of threads have expressed you need a Corolla TB ending in 030 otherwise you need to do a chip swap. (mine is from a 2005) I bought one and it has a noticeably larger air path than the stock TB.

The only other difference I notice on the TB is that the coolant lines are at different angles than the Yaris TB, but that is an easy fix.

I wish we could nail down this information. I have no plans to install the TB on the stock manifold, I'm waiting until I get a new intake manifold. I'm excited to see what MicroImage is going to come up with, but my current plan is to buy a xB weapon-r and have a local fabricator design a new plenum and a 1zz TB flange. The weapon-r manifold is just a starting point really.
tooterThread starterLos Angeles · Aug 25, 2012#771
It's nice to know that I might have inspired others to explore on their own.🙂 The Weapon R Xb manifold you want is presently selling for $469 including shipping on ebay... but I haven't yet been able to find any actual dyno run results even though Weapon R claims their intake manifold makes 15 to 30 horsepower in a normally aspirated engine.
suckerfaceMilwaukee, WI · Aug 25, 2012#772
4/20 is right, it's part number 22030-0D030 that I got. Personally, I completely bypassed the coolant lines.

Hit up eBay or a junk yard now and then. You'll probably be better off at the junk yard as on eBay they're all around $150.

Can't wait for the MI manifold! It's going to be ported for the 1ZZ TB, correct?
malibuguyWestminster, MD · Aug 25, 2012#773
the dyno looks like it would support an 8500-9000rpm screamer very well
tooterThread starterLos Angeles · Aug 25, 2012#774
Originally Posted by thebarber ↑
Disappointing numbers...but at least you tried. For that, I applaud you.
And those are HONEST numbers, barber. 🙂

Both sets of runs done with a bone stock engine and a bone stock throttle body, just regular 87 octane pump gas with no additives, and no tuning. No dishonest tweaked numbers or tricky deceitful chilling down the intake before running. As much as I wanted the tooter to show an improvement, I won't cheat just to sell a manifold. 👍
cali yarisCanoga Park, CA · Aug 25, 2012#775
but I haven't yet been able to find any actual dyno run results
I know of one xB owner who dyno'd with that mani and lost hp, but I can't find the thread on SL any more.

Can't wait for the MI manifold! It's going to be ported for the 1ZZ TB, correct?
Yes, the proto came yesterday, and it is ported for the 1ZZ. I think there is a thread for that project, so I'll post comments over there. This epic thread belongs to tooter. 👍
packetraceQuebec · Aug 25, 2012#776
will the 1nz tb fit ?
cali yarisCanoga Park, CA · Aug 25, 2012#777
fitment is the same
4/20 NEVER FORGETPortland, OR · Aug 25, 2012#778
If the weapon-r manifold made the claimed amount of horsepower you know there would be dyno charts to support it. It doesn't, so there are none. I am surprised there are seriously nearly zero charts online. Some google image searches show some charts paired up with other mods, and none of those charts show large gains over what I/h/e are worth.

I'm excited to see this MicroImage manifold. If they are so close to a finished product there is no sense in building my own right now. My ideas from working on NA Hondas in the past was you could improve the plenum design of the weapon-r, as well as add velocity stacks to each intake port inside the manifold. Maybe the problem with the weapon-r is they were trying to find a balance between NA and FI performance?
cali yarisCanoga Park, CA · Aug 25, 2012#779
Possible test install as soon as tomorrow. 👍
tooterThread starterLos Angeles · Aug 26, 2012#780
Originally Posted by 4/20 NEVER FORGET ↑
If the weapon-r manifold made the claimed amount of horsepower you know there would be dyno charts to support it. It doesn't, so there are none. I am surprised there are seriously nearly zero charts online. Some google image searches show some charts paired up with other mods, and none of those charts show large gains over what I/h/e are worth.
I also looked and found nothing definitive behind Weapon R's advertized 15 to 30 horsepower gain. But I'll bet that they might be able to get that with a combination of other mods.

The actual performance of an intake manifold can be muddied up with other concurrent mods like intake, throttle body, injectors, fuel, e tuning, or exhaust, so that you never actually know whether or not an increase was in the manifold. This is why I did the two sets of runs with the manifold as the only change, so that I would have an accurate assessment of it alone.

I'm excited to see this MicroImage manifold. If they are so close to a finished product there is no sense in building my own right now. My ideas from working on NA Hondas in the past was you could improve the plenum design of the weapon-r, as well as add velocity stacks to each intake port inside the manifold. Maybe the problem with the weapon-r is they were trying to find a balance between NA and FI performance?
It sure doesn't hurt to hold onto your $469 and wait to see what happens. 👍

And that makes sense. From what I've read, forced induction plenums need to be larger than normally aspirated ones so that one plenum size cannot ideally fit both. But a single plenum size compromise between the two could work less than ideally for both.
thebarberGrand Rapids, MI · Aug 26, 2012#781
Originally Posted by malibuguy ↑
the dyno looks like it would support an 8500-9000rpm screamer very well
I disagree. If you follow the tq curve linearly to 6500rpm and work out the HP you get 70wtq and about 85whp....
CoryMWhite Rock BC · Aug 26, 2012#782
Hats off to you Tooter. Always respect those who try new things.
I would suggest swapping that intake onto a modded/boosted engine at the dyno and seeing what happens.
Cheers.
malibuguyWestminster, MD · Aug 26, 2012#783
Originally Posted by thebarber ↑
I disagree. If you follow the tq curve linearly to 6500rpm and work out the HP you get 70wtq and about 85whp....
Probably with a stock motor sure...but a proper motor moving a shit of air and going higher rpms looks like it may benifit.
tooterThread starterLos Angeles · Aug 26, 2012#784
Originally Posted by malibuguy ↑
Probably with a stock motor sure...but a proper motor moving a shit of air and going higher rpms looks like it may benifit.
The 1998 Corolla manifold was designed to flow for a 120 horsepower (at 5,700rpm) 1ZZ FE 1.8 engine that redlined at 6,000 rpm. Our 1NZ FE 1.5 is 20% smaller, so theoretically the manifold could flow past the stock redline if the engine was capable of it. Now if a 20% smaller engine could rev 20% faster, that would put the theoretical redline at 7,200.

I have no idea how a forced induction would work with this manifold. I only know that a guy from Puerto Rico did one. I'll see if I can find the thread with the pic of it...

Picture not included in this copy

This was my inspiration... 🙂
ljming99Singapore · Aug 27, 2012#785
And that makes sense. From what I've read, forced induction plenums need to be larger than normally aspirated ones so that one plenum size cannot ideally fit both. But a single plenum size compromise between the two could work less than ideally for both.
Thats why i said earlier as well, there is "no best of both worlds" ..more of a balance / compromise. The length of the intake was a very good example.

Same as power - you want to make power - you can forget about fuel economy

^^ btw i like the matt black stealth look :)
cali yarisCanoga Park, CA · Aug 27, 2012#786
106 hp / 120 hp = 11.7% difference (more important than simple displacement)
1.5L / 1.8L = 16.7% difference

Where you getting 20%, tooter?
tooterThread starterLos Angeles · Aug 27, 2012#787
Originally Posted by ljming99 ↑
Thats why i said earlier as well, there is "no best of both worlds" ..more of a balance / compromise. The length of the intake was a very good example.
In efforts to bridge that compromise gap, engineers even went so far as to design dual length runner intake manifolds like this Ford Taurus SHO intake manifold for their Yamaha engine, which just has to be one of the most intriguing engines ever to be found in a Ford...

Picture not included in this copy

Coincidently, one of the CNC guys at Origin Design in Santa Monica worked on the design of this manifold. 👍

Same as power - you want to make power - you can forget about fuel economy
That's been one of the unintended consequences of the tooter manifold. My gas mileage average has been consistently higher by about 1.5 mpg and I'm not really sure exactly why. One guess is the combination of its overall smaller volume and slightly longer runners.



^^ btw i like the matt black stealth look :)
How about this silver one? 😉

Picture not included in this copy
tooterThread starterLos Angeles · Aug 27, 2012#788
Originally Posted by cali yaris ↑
106 hp / 120 hp = 11.7% difference (more important than simple displacement)
1.5L / 1.8L = 16.7% difference

Where you getting 20%, tooter?
Should have said the 1ZZ FE was 20% larger than the 1NZ FE.

1.5 +20% of 1.5 = 1.8 😉

Hey, so what's the news on your manifold? Did you run it yesterday?
tooterThread starterLos Angeles · Aug 27, 2012#789
Originally Posted by suckerface ↑
4/20 is right, it's part number 22030-0D030 that I got. Personally, I completely bypassed the coolant lines.

Hit up eBay or a junk yard now and then. You'll probably be better off at the junk yard as on eBay they're all around $150.
Is it this one? It's only $119 and free shipping... 🙂

Picture not included in this copy

Do you know what the base gasket looks like? The reason I'm asking is to determine how to configure the adaptor, as I'm not sure if the larger bore will work with the stock 1NZ FE Oring gasket.
Bluevitz-rsOshawa, Ontario, Canada · Aug 27, 2012#790
If you're going to do it, just get a new gasket from the dealer and base your template off that.
tooterThread starterLos Angeles · Aug 27, 2012#791
Originally Posted by Bluevitz-rs ↑
If you're going to do it, just get a new gasket from the dealer and base your template off that.
Do you know if it's a flat gasket or an O ring?
Bluevitz-rsOshawa, Ontario, Canada · Aug 27, 2012#792
I do not know. I have a 3 bolt throttle body and it's different.
4/20 NEVER FORGETPortland, OR · Aug 27, 2012#793
I haven't got a gasket for mine yet so I don't know either. Mine looks just like the one you posted a picture of, I got mine for $95 from a local wrecker.
suckerfaceMilwaukee, WI · Aug 27, 2012#794
Mine looks the same, and I don't recall using a gasket...

MAKE SURE you check the actual part number. The two 1ZZ TB part numbers, the actual PART looks the same, but you don't need to do the chip swap on one of them.

I'll try to get some video this week of the high idle that I deal with. No tach, so it'll be audio only.
cali yarisCanoga Park, CA · Aug 27, 2012#795
ah. You were going by simple displacement numbers. If you go by bhp, it's only 13% more power. 106 + 13% = 120

Why use displacement instead of power? (neither is particularly relevant, by the way)

Should have said the 1ZZ FE was 20% larger than the 1NZ FE.

1.5 +20% of 1.5 = 1.8
tooterThread starterLos Angeles · Aug 27, 2012#796
Originally Posted by cali yaris ↑
ah. You were going by simple displacement numbers. If you go by bhp, it's only 13% more power. 106 + 13% = 120

Why use displacement instead of power? (neither is particularly relevant, by the way)
Your way is best, Garm. I'm not much of a number cruncher. 😉

By the way, what are the results for your manifold? Have you run it yet?
cali yarisCanoga Park, CA · Aug 27, 2012#797
^ That remains to be seen.

Installing it tonight! IF the car runs ok on it, it stays on for the week. IF it runs ok for the week, dyno on Thursday or Friday. Then go back to stock and dyno again. That's the plan.

Then make a bunch... or don't. 😆
tooterThread starterLos Angeles · Aug 27, 2012#798
Originally Posted by cali yaris ↑
^ That remains to be seen.

Installing it tonight! IF the car runs ok on it, it stays on for the week. IF it runs ok for the week, dyno on Thursday or Friday. Then go back to stock and dyno again. That's the plan.

Then make a bunch... or don't. 😆
I totally understand that! 😉
packetraceQuebec · Aug 27, 2012#799
Originally Posted by cali yaris ↑
^ That remains to be seen.

Installing it tonight! IF the car runs ok on it, it stays on for the week. IF it runs ok for the week, dyno on Thursday or Friday. Then go back to stock and dyno again. That's the plan.

Then make a bunch... or don't. 😆
got pics of the manifold itself ?
cali yarisCanoga Park, CA · Aug 27, 2012#800
yep, but can't post until tomorrow.