Yarisworld Archive

tooter's manifold adventure...

1,454 posts · 559,522 views · page 13 of 30

Replies continued

cali yarisCanoga Park, CA · Aug 15, 2012#601
The second set of dyno pulls need to be done under exactly the same conditions as the baseline pulls with the velocity stack and its matching air filter... except for the tooter manifold being the only change.
That's not going to happen unless ambient temperature and humidity are the same, along with other factors. Did you record ambient conditions and engine intake air temps when you did your baseline pulls?

I think everyone should consider that there is a notable margin for error, counted twice -- once for each dyno session.
Bluevitz-rsOshawa, Ontario, Canada · Aug 15, 2012#602
^ That's why I suggested he swap manifolds on the dyno, but he doesn't want to do that.
cali yarisCanoga Park, CA · Aug 15, 2012#603
It's tooter's show, I'm just enjoying the whole thing. And he's quite content if it doesn't make or lose great power. He's having great fun doing this -- that's all that matters.

I like clarity for all when I see words like "exactly the same"; that was the only purpose for my post. And... it makes the pool more interesting. 🙂
tooterThread starterLos Angeles · Aug 15, 2012#604
Originally Posted by cali yaris ↑
That's not going to happen unless ambient temperature and humidity are the same, along with other factors. Did you record ambient conditions and engine intake air temps when you did your baseline pulls?
Yes. They were automatically logged on the chart:

78.46 °F
29.19 in-Hg
Humidity: 45 %

I think everyone should consider that there is a notable margin for error, counted twice -- once for each dyno session.
Since it's been really hot and dry, I'll try to pick an early morning dyno time on a day when the Santa Ana winds aren't blowing. 🙂
tooterThread starterLos Angeles · Aug 15, 2012#605
Originally Posted by cali yaris ↑
It's tooter's show, I'm just enjoying the whole thing. And he's quite content if it doesn't make or lose great power. He's having great fun doing this -- that's all that matters.

I like clarity for all when I see words like "exactly the same"; that was the only purpose for my post. And... it makes the pool more interesting. 🙂
It's good you pointed that out, Garm. 🙂

By "exactly the same conditions", I meant engine conditions. That the only change between the first dyno runs and the second is the manifold and nothing else.

I'm already happy that the engine runs great, gets good mileage and that the manifold looks really cool. The change won't be much either way because the throttle body, ECU, and engine are all still exactly the same.
malibuguyWestminster, MD · Aug 15, 2012#606
you know...if you ordered your silicone coupler from us...you wouldnt be having this issue ;)
cali yarisCanoga Park, CA · Aug 15, 2012#607
^ Or if he picked one up from my shop. 😉
tooterThread starterLos Angeles · Aug 15, 2012#608
I had ordered one from an ebay seller and was sent a 45 degree instead of a 90 so he's making it right. 🙂
mazillaSan Jacinto California · Aug 15, 2012#609
Originally Posted by malibuguy ↑
you know...if you ordered your silicone coupler from us...you wouldnt be having this issue ;)
Originally Posted by cali yaris ↑
^ Or if he picked one up from my shop. 😉

Or if he got one from ....oh wait, I don't sell anything. 😁
cali yarisCanoga Park, CA · Aug 15, 2012#610
^ and on this forum, neither does malibuguy, and neither does tooter -- but the link to become a vendor is posted for anyone who wants to join the club. 👍
tooterThread starterLos Angeles · Aug 16, 2012#611
Originally Posted by malibuguy ↑
I planned on making my own CAI like the one i made for my old xB. However, if these work out obviously im down for the flanges (as ive been sitting on a 1zz intake for quite a while) and ill just make induction custom to the manifold...and maybe perhaps given tooter graces, reproducing them for a few peoples who dont have fab skills?
Thanks for the offer, guy... 🙂
But I'll be producing complete bolt on tooters myself so as to be able to recover the initial design and production tool-up costs.

Think of your exhausts... When you design a system that no one else has, you want to be the one to make and sell them yourself. 👍
cali yarisCanoga Park, CA · Aug 16, 2012#612
Sorry, no air filter... no dyno. I'm not going to wreck my engine.
Cars with ITB's and velocity stacks dyno every day. Dyno shops don't have particulate matter floating around; if they did, I'd probably choose another shop. 🙂

Since that's not going to hurt your engine, it's not a valid reason to wait.

I don't care when you do it, just pointing out a bad argument when I see one.
cali yarisCanoga Park, CA · Aug 16, 2012#613
more on "wrecking" the motor.

It should be pointed out also that you have no way of knowing the long term affects of your manifold on your motor. In fact, you could be feeding one cylinder too much air, or not enough, with a dramatic decrease in engine longevity.

If you want to know, I suggest a look at your plugs now and 10,000 miles from now, and a compression test would be a good idea as well. All stuff you can do yourself at no cost. 👍
cali yarisCanoga Park, CA · Aug 16, 2012#614
By "exactly the same conditions", I meant engine conditions.
Did you also record intake temps when you did your baseline? Sorry if I missed that post.
xnamerxxso cal · Aug 16, 2012#615
I'll let you know this the Pikes Peak racers don't use air filters and that's back when they ran on dirt. I know this because I had a 900hp TRD 503e engine sitting 2 feet away from me for 2 years.

That was a cool motor ITB"s with a common plenum for the turbo's only bad thing was once the head was bolted on the block couldn't be reused.
Flipper_1938Kentucky · Aug 16, 2012#616
Originally Posted by xnamerxx ↑
the turbo's only bad thing was once the head was bolted on the block couldn't be reused.
Why?
xnamerxxso cal · Aug 16, 2012#617
I don't wanna hijack much but this was the explanation that was given to me by a TRD engineer.

When the heads are bolted onto the block the block would distort, and when the heads would be unbolted the block would remain distorted, and since its a race engine it was all built to a specific tolerance and it couldn't be machined or it would go out of spec.

You also have to remember these engines were build for IMSA racing so they only need to last for a 24hr race and then they would be replaced. Those motors could make an insane amount of power from a 2.3l reliably but for some reason they have turbo failure issues so you either get lucky or you have a motor that cooks after a short period of time.

In case you were wondering they make 900+hp at 31psi only problem is they sound terrible not a nice sounding engine.
tooterThread starterLos Angeles · Aug 16, 2012#618
Originally Posted by cali yaris ↑
Cars with ITB's and velocity stacks dyno every day. Dyno shops don't have particulate matter floating around; if they did, I'd probably choose another shop. 🙂

Since that's not going to hurt your engine, it's not a valid reason to wait.

I don't care when you do it, just pointing out a bad argument when I see one.
Thanks for your input on my bad argument and understanding that I'm just a beginner at this. 🙂 The first pulls were done with the Blox filter, so my common sense tells me that the second ones will also be done with the same filter. I'm still sticking with the manifold being the only change. USPS tracking had the silicone connector arriving yesterday, so I'll be headed to the Post Office tomorrow after work to see what's up.
tooterThread starterLos Angeles · Aug 16, 2012#619
Originally Posted by cali yaris ↑
more on "wrecking" the motor.

It should be pointed out also that you have no way of knowing the long term affects of your manifold on your motor. In fact, you could be feeding one cylinder too much air, or not enough, with a dramatic decrease in engine longevity.

If you want to know, I suggest a look at your plugs now and 10,000 miles from now, and a compression test would be a good idea as well. All stuff you can do yourself at no cost. 👍
Thanks for the good advice, Garm... I'll do just that. 👍
It's one thing I really like about this particular design in that it does not possess the inherent runner inequities of the typical log style manifolds which are fed from one end...

Picture not included in this copy

...because all 4 runners share exactly the same relationship to the throttle body. I'm also counting on the fact that this design had already been produced for 4 years and ran on tens of thousands of Corollas over a time span of as much as 14 years.
tooterThread starterLos Angeles · Aug 16, 2012#620
Originally Posted by cali yaris ↑
Did you also record intake temps when you did your baseline? Sorry if I missed that post.
Yes. It was addressed in post #604.
ljming99Singapore · Aug 16, 2012#621
Originally Posted by tooter ↑
Thanks for your input on my bad argument and understanding that I'm just a beginner at this. 🙂 The first pulls were done with the Blox filter, so my common sense tells me that the second ones will also be done with the same filter. I'm still sticking with the manifold being the only change. USPS tracking had the silicone connector arriving yesterday, so I'll be headed to the Post Office tomorrow after work to see what's up.
Will there be a run with stock airbox as well?

That will be a good baseline to see if just changing the intake manifold alone will account for any gains/loss😁
tooterThread starterLos Angeles · Aug 16, 2012#622
Originally Posted by xnamerxx ↑
I don't wanna hijack much but this was the explanation that was given to me by a TRD engineer.

When the heads are bolted onto the block the block would distort, and when the heads would be unbolted the block would remain distorted, and since its a race engine it was all built to a specific tolerance and it couldn't be machined or it would go out of spec.

You also have to remember these engines were build for IMSA racing so they only need to last for a 24hr race and then they would be replaced. Those motors could make an insane amount of power from a 2.3l reliably but for some reason they have turbo failure issues so you either get lucky or you have a motor that cooks after a short period of time.

In case you were wondering they make 900+hp at 31psi only problem is they sound terrible not a nice sounding engine.

That's really fascinating information namer.
I'm counting on my engine lasting longer than 24 hours. 😉

That Pikes Peak racing engine produced .39 horsepower per cubic centimeter, or over 5.5 times that of a stock Yaris which produces just .07 horsepower per cubic centimeter. 😲

Here's Rod Millen at Pikes Peak...

http://www.youtube.com/watch?v=soQsCyr0hTw
xnamerxxso cal · Aug 16, 2012#623
Originally Posted by tooter ↑
That's really fascinating information namer.
I'm counting on my engine lasting longer than 24 hours. 😉

That Pikes Peak racing engine produced .39 horsepower per cubic centimeter, or over 5.5 times that of a stock Yaris which produces just .07 horsepower per cubic centimeter. 😲

Here's a Toyota Calica at Pikes Peak...

http://www.youtube.com/watch?v=HQj2gWJ30YI
The stories I could tell you about that car 😛 but those are not for the internet.
tooterThread starterLos Angeles · Aug 16, 2012#624
Originally Posted by ljming99 ↑
Will there be a run with stock airbox as well?

That will be a good baseline to see if just changing the intake manifold alone will account for any gains/loss😁
I don't believe that the stock air box would work with this manifold, although I didn't actually try. The throttle body is pushed over to the right about three inches because the long runners aren't compactly wrapped around the plenum like they are on the stock plastic manifold...

Picture not included in this copy
malibuguyWestminster, MD · Aug 16, 2012#625
Originally Posted by tooter ↑
Thanks for the offer, guy... 🙂
But I'll be producing complete bolt on tooters myself so as to be able to recover the initial design and production tool-up costs.

Think of your exhausts... When you design a system that no one else has, you want to be the one to make and sell them yourself. 👍
didnt you lead off this whole thing with the notion of selling just flanges along with completed units? I believe you have even mentioned it more then once.

I dont see what is the issue of selling just flanges (just like we sell all the same componants we use in our kits), you can still make money off of them. I weld my own stuff, its what I do & i already have a manifold to cut up. 🤘

If not, this has been a very disappointing thread. When I pop my hood, I like being able to say...i fabricated that, I made that, etc. Obviously you designed & made the flanges, just like I did not make the mufflers I use (i have made my own mufflers & resonators before however)

🤷🤷🤷
tooterThread starterLos Angeles · Aug 16, 2012#626
Originally Posted by malibuguy ↑
didnt you lead off this whole thing with the notion of selling just flanges along with completed units? I believe you have even mentioned it more then once.
Yes, that's correct malibu. I'm sorry if you had misunderstood. I said that I'm going to sell both... including complete bolt on manifolds. I already have five, four to sell to help cover the money I put into this project, and one for my own car. Man, if you really were in Malibu, I'd be happy to pay you to do the welding, but the cost of freight back and forth would cut too deep.
cali yarisCanoga Park, CA · Aug 17, 2012#627
I said that I'm going to sell both... including complete bolt on manifolds.
Can you refresh our memories and point to that post?
tk-421Dagobah · Aug 17, 2012#628
Originally Posted by tooter ↑
I said that I'm going to sell both... including complete bolt on manifolds. I already have five, four to sell to help cover the money I put into this project, and one for my own car.
Just don't do any selling before you let us mods know first, mkay? 👍
(BTW, I may go for one of these myself)
tooterThread starterLos Angeles · Aug 17, 2012#629
Originally Posted by cali yaris ↑
Can you refresh our memories and point to that post?

Sure, Garm. 🙂

Post #584

Originally Posted by suckerface ↑
Oh really? Is this the full manifold, or just the flange and TB adapter?


Both. 🙂

My goal is to hopefully sell enough tooters to at least break even on the design, material, manufacturing and assembly costs. The market is infintessimally small so I'm only making just enough that I think might actually sell. Kits with the tooter mounting flange, throttle body bolts and adaptor, and gaskets for the do-it-yourselfers and maybe a few assembled units for those who want a complete bolt on manifold. Either way an intake still needs to be modified to fit the unusual placement of the throttlebody. Ironically, the tooter might shine the most in a forced intake situation because it's capable of flowing about 20% more air under identical conditions.
tooterThread starterLos Angeles · Aug 17, 2012#630
Originally Posted by tk-421 ↑
Just don't do any selling before you let us mods know first, mkay? 👍
(BTW, I may go for one of these myself)
Sure will, tk. 👍

I realize that (depending on the dyno results) this will likely not be just a one-off private party sale, and that it crosses the borderline into being a commercial venture. Can you let me know how much you charge for the privelege of selling here so that I can factor that cost into the selling price of the kits and manifolds? Thanks in advance. 🙂
cali yarisCanoga Park, CA · Aug 17, 2012#631
Yay. After that, we'll have to get together and have a Vendor's Meeting. 😆
1.5Tampa · Aug 17, 2012#632
the 6th one can come to Tampa... pending dyno lol
malibuguyWestminster, MD · Aug 17, 2012#633
ive been waiting for my vender info to come in
cali yarisCanoga Park, CA · Aug 17, 2012#634
Just use the link, sign up and pay, you're in as far as I know.
tooterThread starterLos Angeles · Aug 17, 2012#635
Because this is such an extremely small project with a limited market potential and I'm not formally a business, I've already been using YouTube as my point of personal contact because it's free. So I'll be posting some descriptive tooter videos and its intake modification issues, as well as a video of the second dyno runs. 👍
malibuguyWestminster, MD · Aug 17, 2012#636
Hey tooter...i was thinking. I think you took my original statement as making your intakes. What i was referring to was of course assembling one for mine using your platea...however i was talking about making a intake to match up to the manifold...and perhaps make a few more for others just to help people out.
cali yarisCanoga Park, CA · Aug 17, 2012#637
^ You can make any parts you want. A flange for the head isn't proprietary, and neither is a TB adaptor. The manifold itself was designed by Toyota. I personaly wouldn't copy the parts because of (1) professional courtesy, (2) such a small market, and (3) it doesn't make power (that part is just an educated guess at this point).

An intake to go with what tooter made would be really cool and complementary.
tooterThread starterLos Angeles · Aug 17, 2012#638
Originally Posted by malibuguy ↑
Hey tooter...i was thinking. I think you took my original statement as making your intakes. What i was referring to was of course assembling one for mine using your platea...
Hey malibu, 🙂
Of course, that's what the kits will be for. 👍

however i was talking about making a intake to match up to the manifold...and perhaps make a few more for others just to help people out.
I'm not sure I know exactly what you mean. By "intake to match up to the manifold", you mean intake as in short ram or cold air intake air filter assembly to fit onto the throttle body?
tooterThread starterLos Angeles · Aug 17, 2012#639
Originally Posted by cali yaris ↑
^ You can make any parts you want. A flange for the head isn't proprietary, and neither is a TB adaptor.
It sure isn't, Garm. 👍
The guys from Puerto Rico did it first. All I did was have the parts made to do what they did.

The manifold itself was designed by Toyota.
And I'm relying heavily on them having done a good job of it. 😆
You know, this would have been a serious problem if they were still making those manifolds, but since they're all at least decade-old junk yard parts and have long since been rendered obsolete by plastic manifolds, they've sort of fallen into the public domain.


I personaly wouldn't copy the parts because of (1) professional courtesy, (2) such a small market, and (3) it doesn't make power (that part is just an educated guess at this point).
I've already been driving the car a lot... and am pretty certain that the torque curve is going to have some ups and downs! And I still don't know about the top end because of the T shirt issue. 😆

Hey, are you or Jeff going to be around the shop Saturday morning? 🙂

If you have a black 2.5 inch silicone 90 degree connector, I'll drop by and buy one from you. The Post office is clueless as to what happened to the shipment. the tracking number shows acceptance of the parcel, but there is no electronic information after that. It's not the ebay sellers fault either. The guy has been both responsive and communicative.

An intake to go with what tooter made would be really cool and complementary.
I do too! That's a super idea. 👍
cali yarisCanoga Park, CA · Aug 17, 2012#640
^ I might well be around tomorrow morning. Might be racing, though. Email me at mcroimg@gmail.com so we can communicate that way -- I don't access the forums from my phone.
malibuguyWestminster, MD · Aug 17, 2012#641
I wouldnt copy a thing. Im not that kind of guy. As a matter of fact Garm, i got an email thebother day from a guy to copy your center section for the hatchies...i straight up told him "im not copiying garms exhaust"

;)
cali yarisCanoga Park, CA · Aug 17, 2012#642
heh, well thanks. Was it someone on here? 😉
tooterThread starterLos Angeles · Aug 17, 2012#643
Check your messages. 🙂
tk-421Dagobah · Aug 17, 2012#644
Originally Posted by tooter ↑
Can you let me know how much you charge for the privelege of selling here so that I can factor that cost into the selling price of the kits and manifolds?
Like Garm said, it's all a matter of signing up as a vendor and paying your monthly fee (which is around $60 IIRC).
malibuguyWestminster, MD · Aug 18, 2012#645
Originally Posted by cali yaris ↑
heh, well thanks. Was it someone on here? 😉
Sorry i meant center exit.

I have no idea...it was an email at work not a pm.
tooterThread starterLos Angeles · Aug 18, 2012#646
Originally Posted by tk-421 ↑
Like Garm said, it's all a matter of signing up as a vendor and paying your monthly fee (which is around $60 IIRC).
Can you tell me where I can find the link?
tk-421Dagobah · Aug 18, 2012#647
Originally Posted by tooter ↑
Can you tell me where I can find the link?
YGPM 👍
tooterThread starterLos Angeles · Aug 18, 2012#648
Thanks, tk... 🙂 I'll sign up when I'm ready to sell.

Thanks to Garm stocking a 90 degree silicon coupling, I now have an intake that fits the tooter perfectly... 🙂

Picture not included in this copy

It's an ESRI... Extremely Short Ram Intake. 😆
Even though that filter is way oversized and difficult to fit into that small space I didn't want to lose it because that would also mean having to lose the velocity stack.

Hey Malibu... 🙂

If you use a smaller filter, it won't be nearly as difficult to come up with an intake. I just wasn't going to give up using that really cool velocity stack no matter what, so I made it work. A CAI would be even easier for you to fabricate because the cramped space would not be a factor since the pipe would be going into the fenderwell anyways. 👍

So the ingredients to make this intake are:

Weapon R Dragon Short Ram polished aluminium intake tube, cut in half
BLOX 2.5" x 6" Velocity stack, mounting flange cut short
BLOX dry 6" matching dry element air filter
black 2.5" 90 degree coupling, ends trimmed short
black 2.25" straight coupling, trimmed short

These make a smooth flowing very low restriction intake. 👍

I specifically chose the Weapon R tube because the MAF sensor mount is very close to the throttle body, and so could allow for severe cutting while still retaining its operational integrity.



I'll go install it now and post a pic of it on the engine.
cali yarisCanoga Park, CA · Aug 18, 2012#649
glad to help out -- FYI everyone, I'll be putting various hoses and couplings up on the site shortly. 👍
tooterThread starterLos Angeles · Aug 18, 2012#650
Man, you're a life saver! 🙇

Here's the results... 🙂

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

Picture not included in this copy

It's ready to DYNO! 🙂