Yep I haven't done this for the last 3yr I haven't tuned anything with more power than a yairs so thing what ya want and ill do as I've done ill quit tryin to help more power to ya camelll
I NEED Boost... Opinions puh-lease
517 posts · 111,381 views · page 7 of 11
Replies continued
^ Sorry but you WERE incorrect on several of your points. Go ahead and "do as you've done", or stick around and learn something.
We each make our own choices, and you can make yours for you car, but posting totally incorrect information will rightfully get challenged.
We each make our own choices, and you can make yours for you car, but posting totally incorrect information will rightfully get challenged.
Guys, thanks so much for the input.
1.5ty, I appreciate your help but I know for a fact that technique is not going to fly with this car. I've added fuel with the FIC while idling and watched the AFR drop to 14- on my wideband then get immediately corrected. Open loop and closed loop are a big deal here.
Camelll, thanks so much bro. I've been wondering how Blitz handled this. Unfortunately, it gives me no more information than I already have. 🙁
What I find interesting is that you're boosting for awhile while in closed loop, correct? About what PSI do you reach before open loop kicks in in your case? The fact that you've been running two years successfully while boosting in closed loop really leads me to question how unsafe 14.7 is under light boost... Yes, I know I'm comparing two completely different things, but boost is boost - hot compressed air being forced into the manifold. Feel free to correct me if I'm wrong.
1.5ty, I appreciate your help but I know for a fact that technique is not going to fly with this car. I've added fuel with the FIC while idling and watched the AFR drop to 14- on my wideband then get immediately corrected. Open loop and closed loop are a big deal here.
Camelll, thanks so much bro. I've been wondering how Blitz handled this. Unfortunately, it gives me no more information than I already have. 🙁
What I find interesting is that you're boosting for awhile while in closed loop, correct? About what PSI do you reach before open loop kicks in in your case? The fact that you've been running two years successfully while boosting in closed loop really leads me to question how unsafe 14.7 is under light boost... Yes, I know I'm comparing two completely different things, but boost is boost - hot compressed air being forced into the manifold. Feel free to correct me if I'm wrong.
^ open loop doesn't kick in at a psi. It kicks in when the ECU senses a certain load, 75% throttle in our case, and maybe under some other conditions, I don't know.
Right, but wouldn't there be some sort of a trend where open loop usually kicks in? Or can you just floor it, be outside of boost still, and throw the car into open loop?Originally Posted by cali yaris ↑^ open loop doesn't kick in at a psi. It kicks in when the ECU senses a certain load, 75% throttle in our case, and maybe under some other conditions, I don't know.
...Am I just not driving my car hard enough? lol 😕 😁
we actually brainstormed and did some research about this a few years back, if you wanna take the time to sift through it:
The "let's brainstorm how to make a piggyback work" thread
AFC Neo for simple fuel management
Pay close attention to the excel files linked, PK did some good data logging, and yes, no matter what your car is doing, what gear you're in, mash the throttle past the 75% signal and it'll go open loop.
In my mind, the ideal "simple" setup around open and closed loop would be what I call the Jekyll and Hyde approach. A boost controller set up for very gentle boost (maybe 5psi) for use during closed loop operation, and higher boost for open loop, and this would be triggered by the throttle position sensor. Add to that a piggyback that can also have different profiles based on throttle input (such as the apexi SAFC mentioned in the second link above), so that it'll let the ECU do its thing in closed loop, but then mess with things once the throttle goes past 75%.
So, driving "normally", you get the benefit of added power without reaching the limits of the engine/ECU, but when you put your foot down, then you get extra boost, and the piggyback to provide more appropriate fuelling, to unleash the beast within 😉
The "let's brainstorm how to make a piggyback work" thread
AFC Neo for simple fuel management
Pay close attention to the excel files linked, PK did some good data logging, and yes, no matter what your car is doing, what gear you're in, mash the throttle past the 75% signal and it'll go open loop.
In my mind, the ideal "simple" setup around open and closed loop would be what I call the Jekyll and Hyde approach. A boost controller set up for very gentle boost (maybe 5psi) for use during closed loop operation, and higher boost for open loop, and this would be triggered by the throttle position sensor. Add to that a piggyback that can also have different profiles based on throttle input (such as the apexi SAFC mentioned in the second link above), so that it'll let the ECU do its thing in closed loop, but then mess with things once the throttle goes past 75%.
So, driving "normally", you get the benefit of added power without reaching the limits of the engine/ECU, but when you put your foot down, then you get extra boost, and the piggyback to provide more appropriate fuelling, to unleash the beast within 😉
I have an automatic and am not seeing open loop at all (as per Scangauge). The only time I enter open loop is early idling, and taking my foot off the throttle entirely.Originally Posted by camelll ↑Focus shift are you not seeing open loop at all? Do you have a manual or automatic?
Also - the reason I feel stoich may actually be alright is because there is no detonation, and IAT is always close to the ambient outside temp...
eTiMaGo, currently reading through those threads, but I had a thought. Does the ECU need to pass ALL the parameters to enter open loop? Because if not, there is probably a MAF voltage value whereby the ECU determines open loop is needed. If that's the case, a MAF clamp can be set up on the FIC at that value from where boost kicks in.
^^^ I feel the above may be possible due to the manner in which the Blitz fuel controller is hooked up, but 75% throttle might still be needed...
Just remember, that reading is BEFORE the turbo. The air going into the engine is actually a lot hotter.Originally Posted by Focus_Sh1ft ↑...and IAT is always close to the ambient outside temp...
^ Yeah sorry, disregard that. 😛
Looking at those excel sheets, it's pretty aparent 75% throttle plays a large role in changing to open loop. MAF reading seems to be pretty irrelevant, so my previous idea is (most likely) not going to work.
However, what if we mapped the TPS to one of the analog signals of the FIC? Then, could we possibly manipulate that signal to 75%? That would force open loop... This is probably way oversimplified and I'm sure there would be multiple other issues including a CEL.
eTiMaGo, we're going to figure this out this time around. I need my car running safely, and that turbo ain't coming out. 😁
Looking at those excel sheets, it's pretty aparent 75% throttle plays a large role in changing to open loop. MAF reading seems to be pretty irrelevant, so my previous idea is (most likely) not going to work.
However, what if we mapped the TPS to one of the analog signals of the FIC? Then, could we possibly manipulate that signal to 75%? That would force open loop... This is probably way oversimplified and I'm sure there would be multiple other issues including a CEL.
eTiMaGo, we're going to figure this out this time around. I need my car running safely, and that turbo ain't coming out. 😁
we're going to figure this out this time around. I need my car running safely, and that turbo ain't coming out.That's the spirit 👏
Sounds like quite the recipe for unintended acceleration!!!Originally Posted by Focus_Sh1ft ↑However, what if we mapped the TPS to one of the analog signals of the FIC? Then, could we possibly manipulate that signal to 75%? That would force open loop... This is probably way oversimplified and I'm sure there would be multiple other issues including a CEL.
eTiMaGo, we're going to figure this out this time around. I need my car running safely, and that turbo ain't coming out. 😁sir yes sir! but keep in mind all I can offer is theoretical, we need all the experience amassed over the past few years from our 1NZ gurus 🙂
Agreed, I'm hoping others with some knowledge will chime in with ideas. I'm really hoping to get this working with the FIC, and I know we can do it...Originally Posted by eTiMaGo ↑Sounds like quite the recipe for unintended acceleration!!!
sir yes sir! but keep in mind all I can offer is theoretical, we need all the experience amassed over the past few years from our 1NZ gurus 🙂
Regarding the unintended acceleration, I don't think that would happen. The actual throttle plate would be at less than 75%, but the ECU would think it's time for open loop and give us fueling control. We could clamp the MAF if necessary as well.
But I can see what you're saying... If the ECU sees an open throttle, it would increase the engine speed right? I need to look at the service manuals a bit more...
When I get the chance, the first thing I'm doing is fooling around with the O2 sensors.
I don't think you can do that with TBW. If the ECU sees more than what's input and the output of the throttle plate doesn't match, it'll go into failsafe.
another (cheaper) piece of electronics to fiddle around with the MAF signal in open loop, the HKS AFR (Air Fuel Regulator). Very simple little box with a dial for the degree of adjustment of the MAF signal (leaner or richer). Nowhere as precise as a proper piggyback, as there is no RPM-specific or throttle-specific arrangement, but it could work well to get an *overall* richer or leaner fuel mix while in open loop, similar effect to getting bigger injectors, I suppose!
No updates on tuning unfortunately, haven't had time to deal with it yet. However, I did redo my oil pan as per Garm's observation about the removable stems. No leaks from it now 👍
Unbelievably though, I'm now back to dealing with coolant leaks. I don't know what the hell I'm doing wrong. I switched to M12 adapters that fit on the turbo VERY snug, but yet they still leak! I was so pissed when I noticed this yesterday, because I really don't know where to go from here. I'm thinking about just yanking water cooling 🤷
The only thought I had was that the hole on the adapters is too small and is creating a huge pressure buildup, which causes the coolant to back out through the threads. I have some pictures, but they suck. Basically, the diameter of the holes is about half of the lines I'm using. The adapters were really meant to be used for getting a pressure reading for a gauge. What do you guys think?
This is all getting incredibly frustrating... I just don't have time to deal with this BS over and over again with my classes. Oh, and I'm not even going to begin on how impossible it was to get those stems off. Unless you have an M4 female torx socket, you're practically SOL.
Unbelievably though, I'm now back to dealing with coolant leaks. I don't know what the hell I'm doing wrong. I switched to M12 adapters that fit on the turbo VERY snug, but yet they still leak! I was so pissed when I noticed this yesterday, because I really don't know where to go from here. I'm thinking about just yanking water cooling 🤷
The only thought I had was that the hole on the adapters is too small and is creating a huge pressure buildup, which causes the coolant to back out through the threads. I have some pictures, but they suck. Basically, the diameter of the holes is about half of the lines I'm using. The adapters were really meant to be used for getting a pressure reading for a gauge. What do you guys think?
This is all getting incredibly frustrating... I just don't have time to deal with this BS over and over again with my classes. Oh, and I'm not even going to begin on how impossible it was to get those stems off. Unless you have an M4 female torx socket, you're practically SOL.
4 attachments not included in this copy
Oh yeah also - read somewhere (MI?) that a 10% underdrive pulley decreases max boost obtainable or something?
Explain?
Explain?
only for a supercharger, which is belt-driven ;)
underdrive pulley makes the supercharger pulley turn more slowly, DEcreasing boost.
no worries for you.
just YANK the water cooling and add it later. Just means you have to idle the car when you park it for now. Minimize your frustration!
no worries for you.
just YANK the water cooling and add it later. Just means you have to idle the car when you park it for now. Minimize your frustration!
So if u yank the water cooling won't it overheat?
it is also oil cooled, the water cooling was just a backup so you could abuse the turbo and not worry.Originally Posted by sleey0 ↑So if u yank the water cooling won't it overheat?
As I was reading the last 2 pages it seems like there is a big ? on O2 Control, Open/ Closed loop etc...
Since now I am studying into standalone ecu management systems all this big questions aren't a taboo for me anymore.
The only issue with the information I am going to mention is that eventually I don't know for sure if the Toyota Stock Ecu works exactly the same but at least you can have something to refer on man 🙂
Below is a tab of information on my Platinum Sport ecu for my wideband. All settings are critical to have a good working engine at all conditions :
1. There are two types, Wideband and Narrowband. Usually wideband sensors are able to adjust fuel at higher rpm than narrow band
2. Target Voltage
- Only valid for Narrowband sensors. This is the sensor voltage that the ECU will try to target. This should be between the two voltages that the sensor outputs for below stoichiometric and above stoichiometric. Setting this target too close to either of these voltages may lead the controller to not function.
3. Idle Target Voltage
- Only valid for Narrowband sensors. This is usually set slightly higher than the above target voltage to help richen the idle mixtures to aid in idle smoothness.
4. Maximum Increase
- Maximum percentage increase in fuel that is allowed by the O2 controller. (Max 25%).
5. Maximum Decrease
- Maximum percentage decrease in fuel that is allowed by the O2 controller. (Max 25%).
6. Proportional Control
- This value alters the gain or sensitivity of the controller. The Proportional Control affect the sensitvity of the short term control.
7. Integral Control
- This value alters the gain or sensitivity of the controller. The Integral Control affect the sensitivity of the long term trim.
8. Sample Rate
- The rate at which the controller will read the O2 sensor and calculate the correction when above the idle RPM. If this is set too fast, the controller will over-react and a very unstable control will result. If this is set too slow, then the O2 controller will be slow to move towards its target and may not achieve the slight oscillations that are desirable.
9. Idle Sample Rate
- The rate at which the controller will read the O2 sensor and calculate the correction when below the idle RPM. If this is set too fast, the controller will over-react and a very unstable control will result. If this is set too slow, then the O2 controller will be slow to move towards its target and may not achieve the slight oscillations that are desirable.
10. Post Start Delay
- A cold O2 sensor voltage reading is always low. Set this value so that the sensor has enough time to reach operating temperature.
11. Delay Till Control
- This setting will delay when the closed loop O2 control will start when all the conditions are met. This helps the controller stop cutting in and out when on the border of one of the conditions that need to be satisfied.
12. Lower RPM
- The minimum RPM at which O2 control will happen. If this value is greater than this value then O2 control at idle will be disabled.
13. Idle RPM
- When the engine speed is below this value and there is zero throttle then the O2 Target Idle Voltage is used. To disable the use of this parameter then set it lower than the Low RPM value.
14. Upper RPM
- The maximum RPM at which O2 control will happen. Having O2 control off at RPM may be desirable if you are running a narrow band sensor.
15. Operating Temperature
- O2 control will only work above this coolant temperature.
16. Limit Select
- Choose if TPS or MAP sensor or Both will disable O2 control. If set to Both, then only one condition has to fail for O2 control to be disabled.
17. MAP Limit
- If load select is MAP or both, any MAP senor reading above this value disables O2 control.
18. Throttle Limit
- If load select is TPS or both, any throttle position above this percentage disables O2 control
Regarding open/closed loop situation. If one of these settings are above or below limits the system begins to get reference on a fuel basemap set by a tuner and that would be open loop. If all is within range then you are closed loop.
As I said, Toyota could have different, less or more settings in their own ecu so just keep this info just for your reference on not a 100% info yours works exactly with the same setup.
Cheers
Since now I am studying into standalone ecu management systems all this big questions aren't a taboo for me anymore.
The only issue with the information I am going to mention is that eventually I don't know for sure if the Toyota Stock Ecu works exactly the same but at least you can have something to refer on man 🙂
Below is a tab of information on my Platinum Sport ecu for my wideband. All settings are critical to have a good working engine at all conditions :
1. There are two types, Wideband and Narrowband. Usually wideband sensors are able to adjust fuel at higher rpm than narrow band
2. Target Voltage
- Only valid for Narrowband sensors. This is the sensor voltage that the ECU will try to target. This should be between the two voltages that the sensor outputs for below stoichiometric and above stoichiometric. Setting this target too close to either of these voltages may lead the controller to not function.
3. Idle Target Voltage
- Only valid for Narrowband sensors. This is usually set slightly higher than the above target voltage to help richen the idle mixtures to aid in idle smoothness.
4. Maximum Increase
- Maximum percentage increase in fuel that is allowed by the O2 controller. (Max 25%).
5. Maximum Decrease
- Maximum percentage decrease in fuel that is allowed by the O2 controller. (Max 25%).
6. Proportional Control
- This value alters the gain or sensitivity of the controller. The Proportional Control affect the sensitvity of the short term control.
7. Integral Control
- This value alters the gain or sensitivity of the controller. The Integral Control affect the sensitivity of the long term trim.
8. Sample Rate
- The rate at which the controller will read the O2 sensor and calculate the correction when above the idle RPM. If this is set too fast, the controller will over-react and a very unstable control will result. If this is set too slow, then the O2 controller will be slow to move towards its target and may not achieve the slight oscillations that are desirable.
9. Idle Sample Rate
- The rate at which the controller will read the O2 sensor and calculate the correction when below the idle RPM. If this is set too fast, the controller will over-react and a very unstable control will result. If this is set too slow, then the O2 controller will be slow to move towards its target and may not achieve the slight oscillations that are desirable.
10. Post Start Delay
- A cold O2 sensor voltage reading is always low. Set this value so that the sensor has enough time to reach operating temperature.
11. Delay Till Control
- This setting will delay when the closed loop O2 control will start when all the conditions are met. This helps the controller stop cutting in and out when on the border of one of the conditions that need to be satisfied.
12. Lower RPM
- The minimum RPM at which O2 control will happen. If this value is greater than this value then O2 control at idle will be disabled.
13. Idle RPM
- When the engine speed is below this value and there is zero throttle then the O2 Target Idle Voltage is used. To disable the use of this parameter then set it lower than the Low RPM value.
14. Upper RPM
- The maximum RPM at which O2 control will happen. Having O2 control off at RPM may be desirable if you are running a narrow band sensor.
15. Operating Temperature
- O2 control will only work above this coolant temperature.
16. Limit Select
- Choose if TPS or MAP sensor or Both will disable O2 control. If set to Both, then only one condition has to fail for O2 control to be disabled.
17. MAP Limit
- If load select is MAP or both, any MAP senor reading above this value disables O2 control.
18. Throttle Limit
- If load select is TPS or both, any throttle position above this percentage disables O2 control
Regarding open/closed loop situation. If one of these settings are above or below limits the system begins to get reference on a fuel basemap set by a tuner and that would be open loop. If all is within range then you are closed loop.
As I said, Toyota could have different, less or more settings in their own ecu so just keep this info just for your reference on not a 100% info yours works exactly with the same setup.
Cheers
1 attachment not included in this copy
There are two types, Wideband and Narrowband. Usually wideband sensors are able to adjust fuel at higher rpm than narrow bandSensors don't adjust anything? 🤷
I think he meant "detect", in terms of giving more accurate information in order to make adjustments :)
Wideband is faster sampling for one thing, therefore more responsive on the gauge. Maybe he meant that. 😉
Here's some updates for anyone wondering.
I'm now 100% sure the size of the adapters needed for water cooling are M12x1.25. I'm currently running M12x1.0 with some high temp silicone sealant and I guess it's working.
Believe it or not, but after nearly two weeks of no CELs, P0101 has come back. I've cleared it and it continues to return. Confusing? Yes.
I bought a used AEM meth kit for $180 shipped. 👍
It'll be sitting around for a couple months, but I had money in paypal I needed to spend and that was a decent deal.
This week, I'll be continuing to work with the FIC. The first thing I'm going to do is get the O2 wire hooked up and see how much I can manipulate the signal before I start getting CELs. I've thought about it, and that + a MAF clamp could very well work to get a decent AFR in closed loop.
I'm now 100% sure the size of the adapters needed for water cooling are M12x1.25. I'm currently running M12x1.0 with some high temp silicone sealant and I guess it's working.
Believe it or not, but after nearly two weeks of no CELs, P0101 has come back. I've cleared it and it continues to return. Confusing? Yes.
I bought a used AEM meth kit for $180 shipped. 👍
It'll be sitting around for a couple months, but I had money in paypal I needed to spend and that was a decent deal.
This week, I'll be continuing to work with the FIC. The first thing I'm going to do is get the O2 wire hooked up and see how much I can manipulate the signal before I start getting CELs. I've thought about it, and that + a MAF clamp could very well work to get a decent AFR in closed loop.
Worked on the FIC today with nothing but negative results lol. I've decided to wait and tune once I get my meth kit hooked up (which is on its way 👍), but I need to figure out how I'm doing it still.
But back to the FIC. Obviously, the best case scenario as I mentioned is to get the O2 manipulated. So I hooked up the O21+ wire today (tap AFR sensor signal wire C20-47), and had nothing but problems.
As per AEM guides I tried no resistor, then resistors (in-line, before the tap location). I tried 1k, 5.5k, 11.2k and got nothing but bad results. The car would start, but it would idle very rough. Looking at my scangauge I noticed a NEGATIVE ignition timing, but the car still was able to enter closed loop. Then it started massively richening the mix until the car just stunk of gasoline (maxed at 10 on my UEGO). The resistor value didn't change the results.
The jumper harness still allows the car to run just fine, so the FIC is clearly at fault in some way. Also, I didn't get any codes... Whose got some bright ideas? 😁
But back to the FIC. Obviously, the best case scenario as I mentioned is to get the O2 manipulated. So I hooked up the O21+ wire today (tap AFR sensor signal wire C20-47), and had nothing but problems.
As per AEM guides I tried no resistor, then resistors (in-line, before the tap location). I tried 1k, 5.5k, 11.2k and got nothing but bad results. The car would start, but it would idle very rough. Looking at my scangauge I noticed a NEGATIVE ignition timing, but the car still was able to enter closed loop. Then it started massively richening the mix until the car just stunk of gasoline (maxed at 10 on my UEGO). The resistor value didn't change the results.
The jumper harness still allows the car to run just fine, so the FIC is clearly at fault in some way. Also, I didn't get any codes... Whose got some bright ideas? 😁
Wish I could help. I removed the top O2 sensor and richened the mixture buy 15% whenever out of boost. And obviously progressively more when in the boost. The car is runing sweet right now with no bumps or jerks and no dying at idle. Also I am in the 11-13:1 range whenever im driving in or out of boost. The car runs so much smoother now. Although I have to deal with check engine light.
I tryed to remove the bulb but their is no bulb. Its a LED soldered on a circuit board. Also that dam annoying seat belt chime is mounted on the back side of the same circuit board.
I did remove the chime but for now I left the LED connected. The light does not bother me. I am just tired of answering questions from people riding in my car. I am also thinking of recirculating those blow off gasses. The car will still dye out sometimes if you let off the gas at full boost and hold the clutch in.
I tryed to remove the bulb but their is no bulb. Its a LED soldered on a circuit board. Also that dam annoying seat belt chime is mounted on the back side of the same circuit board.
I did remove the chime but for now I left the LED connected. The light does not bother me. I am just tired of answering questions from people riding in my car. I am also thinking of recirculating those blow off gasses. The car will still dye out sometimes if you let off the gas at full boost and hold the clutch in.
You probably have a huge flame througher out the tail pipe too LOL 🤣Originally Posted by pimp my yaris ↑I am also thinking of recirculating those blow off gasses. The car will still dye out sometimes if you let off the gas at full boost and hold the clutch in.
a little square of black electrical tape, well placed on the gauge cluster will "fix" your CEL, and can be reverted anytime.
I tryed to remove the bulb but their is no bulb. Its a LED soldered on a circuit board. Also that dam annoying seat belt chime is mounted on the back side of the same circuit board.Couldn't you just cut the trace that powers the bulb?
I'm going to try switching firmwares on the FIC today and see if that does anything...
Hey guys...
Why the hell is there oil in my intercooler? lol
It's not a lot, and it seems like it's been there for awhile. Could it be from when my return was clogged?
Why the hell is there oil in my intercooler? lol
It's not a lot, and it seems like it's been there for awhile. Could it be from when my return was clogged?
Yeah, either you had blow by from the turbo, or the seals are gone. Clean it up and if it comes back you'll know the seals are done in the turbo. If it stays clean, then it was just that one time.
How to clean it up? and he has to clean the piping too right?
It was pooling in the intercooler, the pipes from what I could tell had an oily feel to them but eh. I think it was just the one time, otherwise I would have at least noticed I was losing a large amount of oil...
Actually at the time, it chose both lol. When I fixed the clog I immediately noticed it stopped seeping out the turbo flange, so I figured the seals were good. I would like to think if it was a problem that I would have noticed I've been burning oil, which I haven't.Originally Posted by cdydjded ↑If your return was clogged oil from the center housing has only 2 places to go, out the compressor side of the turbo (cold side) or the turbine side (hot side). Apparently it chose the compressor side. Now that is of course if nothing is mechanically wrong with the turbo itself...
Anyone have anything to say regarding the FIC?
Meth kit will be here shortly...
I've been digging in and trying to understand fully how this will give me improved performance, and realize advancing timing is PROBABLY going to be a big deal. I may be speaking too soon, but I have my doubts. I hate to have to do this, but I'm probably going to sell my FIC and grab an Emanage Ultimate. It looks to be the only way I'm going to get the most out of my setup.
If anyone is interested, I'm currently planning on selling my FIC (just the box, no harness) for $150.
I've been digging in and trying to understand fully how this will give me improved performance, and realize advancing timing is PROBABLY going to be a big deal. I may be speaking too soon, but I have my doubts. I hate to have to do this, but I'm probably going to sell my FIC and grab an Emanage Ultimate. It looks to be the only way I'm going to get the most out of my setup.
If anyone is interested, I'm currently planning on selling my FIC (just the box, no harness) for $150.
Wo man sorry to hear about you selling it. Did you try taking your car to a tuner to see if they could get more? Would hate to see u throw away your moneyOriginally Posted by Focus_Sh1ft ↑Meth kit will be here shortly...
I've been digging in and trying to understand fully how this will give me improved performance, and realize advancing timing is PROBABLY going to be a big deal. I may be speaking too soon, but I have my doubts. I hate to have to do this, but I'm probably going to sell my FIC and grab an Emanage Ultimate. It looks to be the only way I'm going to get the most out of my setup.
If anyone is interested, I'm currently planning on selling my FIC (just the box, no harness) for $150.
Running methanol injection allows for advancing timing, doesn't it? There's more power to be had there, and the FIC only retards it.Originally Posted by cdydjded ↑Advanced timing & boost is a major no no, Whay are you going to sell the FIC?
If I'm not mistaken, the Emanage Ultimate can only retard timing as well. So you won't be any better off. Just stick with the FIC and save your money.
E-manage is crap...Complete shit. You shouldn't use it even if it came wraped in 50.00 dollar bills. It's cheap electronics in pretty box.
AEM/FIC alot better. Keep your AEM.
#1 I don't see why when you guys have real issues you don't call and talk to someone at AEM? Intead you rely on someone here to have a magic answer. AEM has great techs and will guide you through anything you need. They will even put you in contact with a real tunner closest to your house. That unit is quite capable of alot of things. Call and talk to the horses mouth.
#2 Meth will allow you to retard timming. That is why most people use it, to get more boost without detonation. It's like running higher grade fuel for cheap. And fellas don't use Heet and window wash fluid just buy some M1 methanol from a VP dealer. Quit being so damn cheap. It cost about 40.00 for 5 Gal. then mix it 50/50. This is your motor not a shift knob or some other gay bolt on part.
XBG
AEM/FIC alot better. Keep your AEM.
#1 I don't see why when you guys have real issues you don't call and talk to someone at AEM? Intead you rely on someone here to have a magic answer. AEM has great techs and will guide you through anything you need. They will even put you in contact with a real tunner closest to your house. That unit is quite capable of alot of things. Call and talk to the horses mouth.
#2 Meth will allow you to retard timming. That is why most people use it, to get more boost without detonation. It's like running higher grade fuel for cheap. And fellas don't use Heet and window wash fluid just buy some M1 methanol from a VP dealer. Quit being so damn cheap. It cost about 40.00 for 5 Gal. then mix it 50/50. This is your motor not a shift knob or some other gay bolt on part.
XBG
Hmm, I clearly have this all mixed up. I like your idea XBG, I might try to find a tuner to talk to to get some real opinions.
I'm wondering if there's even any point to running meth if all I'm adjusting is AFRs then?
I'm wondering if there's even any point to running meth if all I'm adjusting is AFRs then?
AEM has great techs and will guide you through anything you need.Not in my experience. Getting good help from them is about as easy as pulling teeth.
Yes, sometimes they can be a bare to deal with. But I find in most cases it's all about approach. But like any company theres good days and bad days. For me I've had no issues dealing with them. If you feel your getting the run-around ask for Greg Nakano and tell him your issues. should resolve most issues.
XBG
XBG
Two things...
First. Could anyone who has a meth kit installed show me how they have their tank mounted? I'm struggling to find a spot, but I'm pretty sure I need to get creative with brackets somewhere in the trunk.
Secondly, I'm almost positive I can't make past 4.5 psi of boost. I've been wondering about this for awhile, and it seems to max around there. I was flooring it earlier today and I still got the same results. I'm thinking I extended the actuator on accident when I had to disassemble the turbo. Think it's worth adjusting/shortening the actuator a bit to see what happens?
First. Could anyone who has a meth kit installed show me how they have their tank mounted? I'm struggling to find a spot, but I'm pretty sure I need to get creative with brackets somewhere in the trunk.
Secondly, I'm almost positive I can't make past 4.5 psi of boost. I've been wondering about this for awhile, and it seems to max around there. I was flooring it earlier today and I still got the same results. I'm thinking I extended the actuator on accident when I had to disassemble the turbo. Think it's worth adjusting/shortening the actuator a bit to see what happens?
Yes it sounds like the wastegate isn't closing completely. Thats way to low. I had trouble trying to get mine to boost under 10psi. I kept shooting to 12psi due to a restricted wastgate. Now I max at 8psi.
I did call AEM tech line and they were very helpfull and they know their shit as well. I retarded my timing 2 degrees under high engine load using the timing map with the FIC. I dont think their is anything the E-manage can do that the AEM/FIC cant do. I have had very good luck with this thing considering this is the first piggy back I have ever tuned. If I upgraded to a stand alone, their is no doubt it would be AEM.
Been talking to PETERPOOP the last few days and he brought up a really good idea that I had, until recently, ignored.
Originally, I was under the impression that a boost controller was used merely to raise boost without having to change out the spring in the actuator. However, I didn't realize they could potentially be used to optimize a turbo setup. It seems that by using a boost controller, you're able to keep the wastegate completely closed until desired boost is reached. With just the wastegate, it should begin opening way before maximum boost is reached, thus diverting some exhaust gas too early...
So if the above is correct, this essential means quicker spooling, yes? What do you guys think? I'm always looking for ways to get the most out of my setup, since there isn't much else left to do other than head work / building an engine.
Originally, I was under the impression that a boost controller was used merely to raise boost without having to change out the spring in the actuator. However, I didn't realize they could potentially be used to optimize a turbo setup. It seems that by using a boost controller, you're able to keep the wastegate completely closed until desired boost is reached. With just the wastegate, it should begin opening way before maximum boost is reached, thus diverting some exhaust gas too early...
So if the above is correct, this essential means quicker spooling, yes? What do you guys think? I'm always looking for ways to get the most out of my setup, since there isn't much else left to do other than head work / building an engine.
100% agreed.
If you aiming for 8psi, the waste gate will start to open at say 4-5psi and slowly open until 8psi is approached wasting exhaust energy. With an ELECTRONIC boost controller in the system, the waste gate will remain closed utilizing all the exhaust energy until 8psi is achieved.
For Ex.
Without the electronic boost controller, 8psi is only achieved at 3500RPM.
With the electronic boost conroller, 8psi is achieved at 2500rpm.
If you aiming for 8psi, the waste gate will start to open at say 4-5psi and slowly open until 8psi is approached wasting exhaust energy. With an ELECTRONIC boost controller in the system, the waste gate will remain closed utilizing all the exhaust energy until 8psi is achieved.
For Ex.
Without the electronic boost controller, 8psi is only achieved at 3500RPM.
With the electronic boost conroller, 8psi is achieved at 2500rpm.
^ Yes. Did Peterpoop happen to mention that I'm the one who told him that recently? LOL
An example using World Electronics (Chris Rado) boost controller:
Picture not included in this copy
An example using World Electronics (Chris Rado) boost controller:
Picture not included in this copy
Yes Garm.
My only question is why didn't someone point this out sooner? This seems like a huge improvement. Even that figure shows a stupid amount of additional power being made.
Gonna look into some electronic ones. Any suggestions?
My only question is why didn't someone point this out sooner? This seems like a huge improvement. Even that figure shows a stupid amount of additional power being made.
Gonna look into some electronic ones. Any suggestions?