Replies continued
ParmasML · Sep 2, 2010#201 Originally Posted by
Focus_Sh1ft ↑ The best part is, driving home I got no CELs, and no overheating lights. So I'm going to work on that coupler a bit more, and fix my exhaust leak (could that cause overheating because it's venting into the engine bay?). Then I'll drive the car around and see if I get any overheating lights again. I'm going to assume the worst and expect to get them, so I've been trying to think of ways to keep the water temperature reasonable. So far, the only two ideas I've had was to pull coolant off the turbo (don't want to), and/or to get a performance radiator.
I may be out $170, but it turns out it was money well spent. 🙂
I think you could have saved $170 since probably:
1) The overheating was caused by air present into the system (Emptying the present coolant and fill slowly with new one will solve it). To check that the coolant is free from air, switch on heater in cabin while engine is running and check that is coming hot. If not, there is no flow which is = to air into the system.
2) Error codes will be solved mainly by disconnecting the battery for a half an hour or so.
RE: Exhaust leak. That depends what amount of exhaust is leaking. Mainly the most irritable part is that it will leave a good amount of carbon into the engine bay.
Focus_Sh1ftThread starterNew Jersey · Sep 2, 2010#202Took the car out today and things went great. 😁
One issue though.
I got a CEL after driving for a bit. Pulled into Advance Auto, had the code read, it was an O2 sensor code. The details were something like "bank 1, low positive current." Bank 1 is the sensor on the downpipe, correct? If so, it would explain the burning smell I'm still having lol. Assuming it's that sensor, it isn't ruined because my narrowband still works. So this should be as simple as extending the wire and getting it AWAY from the hot side, and heat wrapping it some more, just need to be 100% sure that it is the wire in question.
firemachine69Sudbury, On · Sep 2, 2010#203I had that same code IIRC, Toyota had to replace the entire downpipe/cat converter system.
(The warranty is quite long, so you should still be covered.)
Nexus1155Dorchester · Sep 2, 2010#204It will be a cold day in hell if Toyota ever replaces anything under warranty in a heavily engine modified vehicle for free. Think you may have ruined the sensor when it was doused in oil if it was doused in oil. you did say the downpipe had oil in it or not? Can you get the exact P code number? Bank 1, you only have one bank :P So it will be S1 B1 if its primary, S2 B1 if its secondary.
Focus_Sh1ftThread starterNew Jersey · Sep 2, 2010#205I don't know if I'm in denial or not, but I don't think it's ruined. It was running fine until the engine got really hot, and there was a burning smell. The shrink wrap on it was very hot as well. The fact that my narrowband still displayed accurate AFRs tells me it's not shot, but if I don't address it now it most certainly will be. I'm going to run some resistance checks now to make sure it is okay.
And Toyota replacing it? I'm on my own from now on lol. I knew this right from day one. Should take my car in one day and see just how much they freak out though. 😉
pimp my yarischicago · Sep 2, 2010#206Video please
cali yarisCanoga Park, CA · Sep 2, 2010#207 Should take my car in one day and see just how much they freak out though.
I did -- that was really fun.
Focus_Sh1ftThread starterNew Jersey · Sep 2, 2010#208 Originally Posted by
cali yaris ↑ I did -- that was really fun.
LOL 😎
Btw guys, I looked up the code I had and it was P2238, "O2 Sensor Positive Current Control Circuit Low." Anyone have any ideas?
As expected, it seems to be related to the A/F sensor. Like I said, the fact that I still get readings on the narrowgauge means it can't be ruined. I still had the CEL when I turned the car on an hour ago too... Does the code just have to be cleared?
And videos.. Soon... Need to find our camera...
EDIT: I'm pretty sure there's a short circuit in the +B wire. Will do a continuity test tomorrow.
pimp my yarischicago · Sep 2, 2010#209Sounds like you got a bad O2 sensor. This is the top sensor before cat. converter. Or possibly your car is runing very rich with the 1zz injectors and may need tuning with the AEM FIC. What does your wideband sensor read?
Nexus1155Dorchester · Sep 2, 2010#210why?harnett county NC · Sep 3, 2010#211 Originally Posted by
cali yaris ↑ I did -- that was really fun.
you should have videoed that, I am sure it was great entertainment.
Focus_Sh1ftThread starterNew Jersey · Sep 3, 2010#212CEL solved. Surprisingly, it was the wire I run off the narrowband gauge, It was either short circuiting / open circuit, but once I cut it the CEL disappeared. All other wires were showing continuity and the correct voltage, so I was getting a little worried.
I also extended the A/F sensor wires and ran it through some heat retardant plastic conduit. I have it running away from the downpipe to the ECM, then across the top. If there was any wire burning issues, this should hopefully be resolved now.
Also had a small coolant leak STILL. I finally just replaced the brass fitting I was using and it seems to be ok now.
As soon as all these damn problems stop coming up I'll get more pictures and video up lol. It's been over a week of battling problems and I'd like to just drive the car care-free. 😛
Focus_Sh1ftThread starterNew Jersey · Sep 3, 2010#213God I need a code reader...
Got another CEL tonight. No idea what it is, but I'm assuming it's O2 related again. I wouldn't be surprised considering I put electric tape too close to the sensor and its become molted and is boiling on the O2 sensor lmao. Gonna uh... Clean that off before drawing any other conclusions. 👍
Focus_Sh1ftThread starterNew Jersey · Sep 5, 2010#214Just got my codes read. I still have P2238, but now I have P0101. The latter is "Mass or Volume Air Flow Circuit Range/Performance." Interesting that both are circuit related... Anyone have any ideas on what's going on?
Would like to add that the car drives absolutely fine.
Nexus1155Dorchester · Sep 5, 2010#215Pulling in more air and running a different AFR than expected more than a certain # of seconds will throw codes im thinking. ECU is constantly adjusting for the airflow and fuel. This only happens when you enter boost? You install your management system with a MAF clamp and a narrowband adjuster to make it seem like the ECU only sees 14.7 all the time?
Focus_Sh1ftThread starterNew Jersey · Sep 5, 2010#216P0101 is new as of yesterday. I've done a decent amount of driving without getting this code so it's weird it would suddenly pop up. I'm still pretty sure P2238 has something to do with wire damage from the heat off the turbo. And management is not yet in use, so until now the ECU has been doing just fine.
Eh, I'm beginning to think you're right about P0101. It makes sense that while boosting it's easily possibly to return a voltage signal that exceeds what the ECU is expecting. Why it's suddenly decided to start happening... Who knows?
Edit: I just found that P2238 could also mean "Barometric Pressure Circuit Intermittent," when in relation to Toyotas. If this was the case, wouldn't it make more sense to get these two codes together?
pimp my yarischicago · Sep 6, 2010#217I extended my O2 sensor wires so it would reach my downpipe and I could route them away from exhaust. My downstream O2 sensor [after coverter] I just left connected and pulled through grommet hole inside on car. It is now under my carpet on the driver side. It took a long ride but my engine light came back on as well. Most likely for the downstream O2 sensor. I am hoping it is a converter efficiency code or evap. code due to boost pressure in the system.
I will go to autozone tomarrow and have them scan it. My scanner is not working on the newer cars. 🙁
Nexus1155Dorchester · Sep 7, 2010#218 Edit: I just found that P2238 could also mean "Barometric Pressure Circuit Intermittent," when in relation to Toyotas. If this was the case, wouldn't it make more sense to get these two codes together?
Means you're car is seeing boost when its only suppose to see vacuum and the ECU is freaking the hell out.?
Focus_Sh1ftThread starterNew Jersey · Sep 7, 2010#219 Originally Posted by
Nexus1155 ↑ Means you're car is seeing boost when its only suppose to see vacuum and the ECU is freaking the hell out.?
This must be the case, because my bank 1 sensor 1 functions totally fine as per my narrowband.
pimp my yaris, lemme know what code(s) you have asap. Best case is we have similar codes...
It's interesting that it took a good deal of driving for your code to come on, because it was the same with me. You'd think that if this theory is correct that the light would come on almost immediately. I need to check how the ECU tests for this and determines there's a problem...
Focus_Sh1ftThread starterNew Jersey · Sep 7, 2010#220Ok, I looked into all this further and realized two things. Firstly, the codes wouldn't come on immediately because it takes two drive cycles for the ECU to determine there is actually a recurring issue. Secondly, I was reading these codes as per the Yaris manual hosted online. P0101 definitely seems to be the maf signal voltage out of range (too high), as a result of boost conditions. As for P2238, the manual lists it as the O2 sensor acting up, not the barometric pressure circuit intermittent. I THINK this is a result of the car running excessively lean. Low positive current on the AF+ wire directly equates to lean conditions. I have a scangauge on the way so I'll run some diagnostics before getting tuned.
Definitely would rather see CELs after boosting than not seeing them. Otherwise the car would clearly just be baffled as to what's happening to it lol.
The cool thing is that if I'm right, a tune will sort out those two CELs. MAF clamping to represent boost conditions, and the proper air/fuel ratio done by fuels map would eliminate P2238.
pimp my yarischicago · Sep 7, 2010#221P0101 is cyl. #1 missfire detected
pimp my yarischicago · Sep 7, 2010#222 Originally Posted by
pimp my yaris ↑ P0101 is cyl. #1 missfire detected
Never mind I was thinking of po301
fnkngrvIn The Hotbox · Sep 8, 2010#223how do you have your gauges set up? Can you take a picture?
Focus_Sh1ftThread starterNew Jersey · Sep 8, 2010#224Picture not included in this copy
Top -> Bottom = Boost -> Narrowband -> Trans Temp
Transmission temperature is currently not installed.
The gauge pod is a generic one from Summit Racing, and it fits pretty eh, but it works nicely. It comes with foam to fill gaps, but I don't care enough.
Picture not included in this copy
Here's the turbo timer I'm not using. The gauge next to it is oil pressure. To the right of it is a voltmeter. I just wanna point out that they're not really 100% setup because I'm waiting on blue LED bulbs for the backlights before I seal the gauges in place and hold the pods with screws in the dash. I have a scangauge on the way that will sit on the steering column.
cali yarisCanoga Park, CA · Sep 8, 2010#225I'm curious why you are using a narrowband?
pimp my yarischicago · Sep 14, 2010#226Jerzy I finally checked my codes today at autozone. I had only one and it was PO137 bank 1 sensor 2 low voltage. I am sure its because I have no cat. and the sensor is still connected but I pulled it inside my car. Its now under the carpet on the driver side. I think I will need a electronic o2 simulatar to pass emissions. I think I will also buy a vaccume check valve to put in on my evap. line.
Focus_Sh1ftThread starterNew Jersey · Sep 14, 2010#227 Originally Posted by
pimp my yaris ↑ Jerzy I finally checked my codes today at autozone. I had only one and it was PO137 bank 1 sensor 2 low voltage. I am sure its because I have no cat. and the sensor is still connected but I pulled it inside my car. Its now under the carpet on the driver side. I think I will need a electronic o2 simulatar to pass emissions. I think I will also buy a vaccume check valve to put in on my evap. line.
Agreed. Definitely because you pulled the cat out. Interesting though that we have similar setups but you don't have a MAF code. My P2238 disappeared and hasnt come back since I cleared my codes about a week ago, but P0101 keeps coming back.
Red HorseCosta mesa, California · Sep 15, 2010#228Has any yaris owner expirience an explosion on their turbo?
pimp my yarischicago · Sep 15, 2010#229 Originally Posted by
Red Horse ↑ Has any yaris owner expirience an explosion on their turbo?
Good question. And please let us know how much boost you were pushing when it happened.
Nexus1155Dorchester · Sep 15, 2010#230They sell O2 Sensor "defoulers" at any auto store, its basically a spacer that pushes the sensor away from the stream so it won't throw codes.
Focus_Sh1ftThread starterNew Jersey · Sep 15, 2010#231Tightened most of my piping connections, checked the MAF, and finally dealt with a small exhaust leak I had. Cleared the code, drove to class, came back on the way home. There must have been a small error on my part when I installed part of the air induction system for this code to keep coming up, otherwise pimp would have it too. I'm confident my MAF sensor works properly, so... maybe a vacuum leak? What would I see on a vacuum gauge if there was a leak?
Still gotta get this thing tuned and stuff... It's like I got lazier now that schools going again 🤷
pimp my yarischicago · Sep 15, 2010#232Just take it easy on the gas till U get her tuned. I can tell U with the wideband, I can tell exactly what my engine is doing and at high rpm's under boost it runs lean without tuning. Too lean! I cant wait to get my piggy back and try to learn some tuning myself. U should invest in the aem wideband. It works great and is made to work with your AEM FIC. I think the mass air sensor max's out under boost and can't properly adjust fuel supply. With the internal map sensor on the FIC we can keep adding fuel after the mass air has maxed out.
Hey jerzy: How much boost are U runing anyway? I dont think a vaccume guage will help that problem. It will only find a leak between the throttle and the engine. I would double check all connections and make sure those silicone connectors and clamps are straight and tight. If they are cocked or crooked they my not seal. Ya that sounded funny!
cali yarisCanoga Park, CA · Sep 16, 2010#233 Too lean!
what are your numbers?
Focus_Sh1ftThread starterNew Jersey · Sep 16, 2010#234The Zage actuator is set to .5 bar. I've only really pushed the boost to 7 psi twice, for now I barely even touch 5 psi during daily driving, for the exact reason you're telling me to take it easy on the gas. I guess the next step really is to see whether or not MAF clamping sorts this trivial code out or not. I'm probably going to tell my tuner to leave the fuel maps alone where the ECU is able to properly adjust, and just focus on the mid and upper RPM range.
Oh yeah, my stupid return flange on the turbo is leaking oil... AGAIN. It's incredibly slow and hasn't really effected my oil level after two weeks of driving, but it needs to be dealt with. My big meaty hands must be over-tightening the bolts. Frustrating 😠
pimp my yarischicago · Sep 16, 2010#235 Originally Posted by
cali yaris ↑ what are your numbers?
It will run as lean as 15-16/1 under boost at high rpm 5-6K 😢
At lower rpm 2-4K everything is cool 12-13/1
ParmasML · Sep 17, 2010#236 Originally Posted by
pimp my yaris ↑ It will run as lean as 15-16/1 under boost at high rpm 5-6K 😢
At lower rpm 2-4K everything is cool 12-13/1
If you saw 15-16 on boost while reving up 5 to 6k consider you have madea slight damage to your pistons as that mixture is way too lean on boost. If you drove several times on that AFR I am very well surprised the engine did not fail.
Please pay attention and get some patience, you don't want the project to be titled " How to end without an engine" instead of " How to turbo an engine", right?
cali yarisCanoga Park, CA · Sep 17, 2010#237A couple of revs that go lean won't kill it. Hell I drove my car for 9 months like that.
Will be interesting to inspect these motors someday when they do get pulled, though -- mine too.
pimp my yarischicago · Sep 17, 2010#238I am driving slow and easy till I get some tuning. I now its to lean and thats why I posted this. I just wanted those who havent had tuning and may not have a wideband to know even at low boost they are runing to lean. So the moral of the story is get some tuning before meltdown and 😢
Focus_Sh1ftThread starterNew Jersey · Sep 18, 2010#239I know why I'm getting P0101, and I'm surprised no one has pointed it out yet.
The Zage BOV is NOT a recirculating one. Being the novice that I am, I thought the vacuum connection that was made to the intake manifold was the bypass valve. It's simply there to operate the piston in the BOV, so there's my air leak lmao. I was wondering how it was capable of making noises without venting the air. Bummer though, because the Zage BOV sounds sweeeeet lol.
So, I have two apparent options. The first being to switch to a bypass valve. The second is more complicated and I see no additional benefit to doing it but... I could use the FIC's MAP sensor to control all my fuel, but that leaves the ECU out of the loop and will probably make it unhappy.
Ideas, guys? I'm probably just going to switch, but would like to see what other options I may have.
Nexus1155Dorchester · Sep 18, 2010#240I just MIGHT have an extra 710 recirc valve from my audi. I'll look around tomorrow for it, if I do I will just send it to you, but that means more custom work because it needs an in and an out and the vacuum line. It is always better to recirc the air. I totally didn't even think of that either, but yeah that could mess things up for you. But you are getting codes when pimp isn't depends on placement of the BOV most likely. Turbo japanese cars are meant to have the BOV noise, try to find an easy way to keep it 😛
I'll let you know as soon as i find out though.
Bluevitz-rsOshawa, Ontario, Canada · Sep 18, 2010#241Simplest solution is to move the MAF after the BOV. You're getting that code because you're venting that metered air to atmosphere. If the BOV is before the MAF, the air gets vented before getting read, so the ECU is only reading what's actually going into the motor.
Only problem I can see is you might not get an accurate reading reading presurized air because the air isn't moving as fast past the MAF. Under vacuum pressure it should work though, it just when you get into boost.
I'm only talking theory here though, not experience, so it might be fine.
pimp my yarischicago · Sep 18, 2010#242My blow off valve also vents outside. My valve is adjustable and I have it set a little tight. My car was dying out in first gear if I hit the gas and quickly let off the gas, because the engine would go very rich. Now it is working good. I bet U could get by with a adjustable BOV. Also their is a specific setting for BOV in the FIC to eliminate any problems with it. Your tuner should be able to fix your code.
Focus_Sh1ftThread starterNew Jersey · Sep 19, 2010#243Thanks for the thoughts, guys. I'd prefer to avoid custom work if I can. And Nexus, thanks, I'll definitely let you know if I do need a bypass valve.
I've put more thought into this, and done some research, and will talk to my tuner about this prior. However, I believe that having fuel maps done on a dyno will eliminate any issues that would arise from dumping metered air (and even now, I've yet to notice any stalling/roughness/etc. after the BOV vents). If I'm correct in saying so, the maps would be designed around test runs which would include moments in which the BOV activates and dumps metered air, correct? My other thought was that if it didn't work this way, then how would cars with higher boost be able to run a BOV without totally stalling the engine?
Originally Posted by
pimp my yaris ↑ My blow off valve also vents outside. My valve is adjustable and I have it set a little tight. My car was dying out in first gear if I hit the gas and quickly let off the gas, because the engine would go very rich. Now it is working good. I bet U could get by with a adjustable BOV. Also their is a specific setting for BOV in the FIC to eliminate any problems with it. Your tuner should be able to fix your code.
My BOV is adjustable as well, but I haven't bothered with it (yet). What bothers me is that we should both have P0101 if my theory was correct... Could it be possible you're letting out LESS metered air because you tightened your BOV? And as a result, your theroetical mix isn't so far off as the actual mix to throw a code?
pimp my yarischicago · Sep 19, 2010#244Could it be possible you're letting out LESS metered air because you tightened your BOV? And as a result, your theroetical mix isn't so far off as the actual mix to throw a code?
I think thats exactly whats going on. My BOV was set so loose when I got it when my hand was near the vent I felt air being sucked in at idle. Once its tuned they program the piggy back to ignor the mass air when U let off the throttle. This is when the BOV vents and for a moment the mass air is still reading, causing it to go very rich.
Bluevitz-rsOshawa, Ontario, Canada · Sep 19, 2010#245You have to remember, when the you shift and close the throttle, the turbo is still spooled to an extent and is still pulling air through the MAF and out the BOV. That's why you get a rich condition. The air going through the MAF isn't going into the motor, but the ECU thinks it is and is still dumping in fuel.
There's a couple of ways around it while using a MAF. You can move it to after the BOV, or program whatever computer you're using to look at the throttle position sensor and have a base map off throttle position, using the MAF for fine adjustment rather than the only input.
Focus_Sh1ftThread starterNew Jersey · Sep 21, 2010#246Anyone know if the FIC can be used with the UEGO wideband to automatically detect AFRs then correct them based on user entry? Would make things VERY easy and simple. Always the best route.
pimp my yarischicago · Sep 21, 2010#247Their are some good videos on Youtube that help descripe the features of the FIC and a little on how it works. All the videos are made by AEM, so their for real. I have the wideband already installed and I should be recieving my FIC tomarrow. I plan on reading all the instructions installing and then trying some tuning myself with the help of those videos. The wideband will tell me if I'm going in the right direction or just making it worse. I would definitely get the wideband. It tells you exactly whats going on and using your tach. U can tell where you need to make adjustments.
I will let U know how it turns out.
Bluevitz-rsOshawa, Ontario, Canada · Sep 21, 2010#248Has anyone concidered the
Allan Phillips Racing ECU for their tuning needs?
I know it's pricy and all, but it looks like it would do everything with ease.
Focus_Sh1ftThread starterNew Jersey · Sep 21, 2010#249Yeah, I'm really on the fence when it comes to tuning... I have only one tuning shop that is near me, and I'm really not crazy about the guy from the three conversations we've had. I wouldn't mind learning some tuning, but am worried that with my inexperience and lack of dyno that I may cause damage... Then again, I did just throw a turbocharger in my car with no mechanical expertise so.. 🤷
I'm definitely leaning towards doing it myself... I'd like to think I get the basics of AFRs and the effect of adding/removing fuel. With a wideband, how hard could it be?
sleey0PA · Sep 21, 2010#250 Originally Posted by cdydjded ↑
If you or anyone need help in tuning the AEM FIC please ask ; )
Can you make a "AEM FIC Basics" thread or something like that?
A lot of us would like to know how to get started and what we should be looking for and doing in there.
I know at least 10 other people that would find it useful, and that is just me so I am sure there would be a ton of interest since there isn't any tuning threads at all.
Thanks!🤘