you will do fine
I NEED Boost... Opinions puh-lease
517 posts · 111,381 views · page 2 of 11
Replies continued
Does the Yaris have a MAG or HALL type crank + cam sensor? Can't find this info anywheres 🤷
Something I never looked into, but most cars nowadays use HALL? Why would you need to know this anyways lol.
I am also wondering where the oil and coolant lines are going to go, for hopefully future reference of course. Would you use braided line, or would you go with the rubber hose i see alot of cars use
I am also wondering where the oil and coolant lines are going to go, for hopefully future reference of course. Would you use braided line, or would you go with the rubber hose i see alot of cars use
I've had no trouble with rubber hose for my return line. I posted pics of the location recently.
I need to know the sensor type for the FIC. And I'll be using a rubber hose for starters (it's part of the kit anyways).Originally Posted by Nexus1155 ↑Something I never looked into, but most cars nowadays use HALL? Why would you need to know this anyways lol.
I am also wondering where the oil and coolant lines are going to go, for hopefully future reference of course. Would you use braided line, or would you go with the rubber hose i see alot of cars use
Thanks cdydjded for confirming that too. I actually thought it was hall effect.
Now, here's the thing. I've been getting very familiar with the FIC install guide and have been debating what I want to do with it. I remember when I first began looking into forced induction, there was at least one mention in every thread about how much of a pain our ECU is due to its learning ability. Originally, I had planned to get the FIC to control as much as possible, but the more I think about it, I think it's the wrong approach. I'm aware that, in the least, I need to use the FIC to provide additional fuel during boost conditions. I admit my knowledge on ECUs is lacking, so I'm hoping you guys here (and my potential tuner) can shed some light on the following: will the ECU make an attempt to adjust timing / ignition / cam position etc. etc. when it sees boost conditions + additional fuel? Or will it rather trim fuel and try to maintain ideal conditions?
cdydjded, this is aimed mainly at you. I know you already told me you were only running fuel maps. However, I was reading one of your older threads recently and saw your plan for how the engine should run: stock without boost, FIC handles boost conditions. I couldn't agree more when it comes to reliability and overall effectiveness. Was this ever achieved?
Ultimately, my epiphany was that I could possibly use the ECU's learning capability to actually aid in having a proper tune, rather than it just being an enormous hassle. Lemme know what you guys think, I'm hoping to get it wired in this week.
Thanks, I'll be taking the same route then.
Today I was poking around in the engine bay, scouting out places to place senders for gauges (and also installing a 1zz TB 😁). Figured out what I'll be doing with everything but the oil pressure gauge. I really can't get at the engine oil pressure assembly. Literally 10 minutes ago, this idea hit me: http://www.glowshiftdirect.com/oilfi...-34unf-16.aspx
Couldn't I use this as a place to receive oil pressure readings AND use as an oil return line for the turbo? It would be installed such that gravity would still return oil properly. My only concern is the filter would be having additional oil dumped in at all times. I'm pretty sure it's not an issue, but could clogging potentially happen?
Today I was poking around in the engine bay, scouting out places to place senders for gauges (and also installing a 1zz TB 😁). Figured out what I'll be doing with everything but the oil pressure gauge. I really can't get at the engine oil pressure assembly. Literally 10 minutes ago, this idea hit me: http://www.glowshiftdirect.com/oilfi...-34unf-16.aspx
Couldn't I use this as a place to receive oil pressure readings AND use as an oil return line for the turbo? It would be installed such that gravity would still return oil properly. My only concern is the filter would be having additional oil dumped in at all times. I'm pretty sure it's not an issue, but could clogging potentially happen?
The oil filter it pressurized. You can only return oil to the pan. Once you have the oil pan off, it's really easy to just drill and tap the block for one. But you could feed the turbo from that plate.
Planning to install it tomorrow actually. I'm going to hook up injector ins/outs as well as power and ground of course.
Today I went to go wire the FIC up, but got kinda confused... This ECM pinout I'm using has got me all sort of confuzzled. Check it out here:
http://www.powerenterpriseusa.net/pr...risControl.pdf
Firstly, everything has two different wires listed and I have no idea what the acronyms stand for. So basically, I have no clue which wires I should be using to tap/intercept. It looks like some things are listed as + and -, while others aren't. Here's what I think needs to be done...
FIC Power - A21-1 or A21-2
FIC Gnd - C20-104
Injector 1 - C20-108
Injector 2 - C20-107
Injector 3 - C20-106
Injector 4 - C20-105
MAF+ - C20-118
MAF- - C20-116
The thing is, even for the injectors, C20-45 is listed next to all of them and I don't understand why? Enlighten me pleeeease. In the mean time, I need a beer. 🍻
... and aloe. 👎
http://www.powerenterpriseusa.net/pr...risControl.pdf
Firstly, everything has two different wires listed and I have no idea what the acronyms stand for. So basically, I have no clue which wires I should be using to tap/intercept. It looks like some things are listed as + and -, while others aren't. Here's what I think needs to be done...
FIC Power - A21-1 or A21-2
FIC Gnd - C20-104
Injector 1 - C20-108
Injector 2 - C20-107
Injector 3 - C20-106
Injector 4 - C20-105
MAF+ - C20-118
MAF- - C20-116
The thing is, even for the injectors, C20-45 is listed next to all of them and I don't understand why? Enlighten me pleeeease. In the mean time, I need a beer. 🍻
... and aloe. 👎
can't help you but i am rooting for ya m8
Thanks a bunch man. 🙂
That C20-45 is probably your common sensor ground. It's separate to the ECU ground.
Not to put you down on wiring (because I love doing wiring. No joke.) but I'm glad my ECU is under the dash and not the hood.
Not to put you down on wiring (because I love doing wiring. No joke.) but I'm glad my ECU is under the dash and not the hood.
cdyjdjeded can probably help you he's got his wired correctly. Try a PM request
Originally Posted by Focus_Sh1ft ↑Today I went to go wire the FIC up, but got kinda confused... This ECM pinout I'm using has got me all sort of confuzzled. Check it out here:
http://www.powerenterpriseusa.net/pr...risControl.pdf
Firstly, everything has two different wires listed and I have no idea what the acronyms stand for. So basically, I have no clue which wires I should be using to tap/intercept. It looks like some things are listed as + and -, while others aren't. Here's what I think needs to be done...
FIC Power - A21-1 or A21-2
FIC Gnd - C20-104
Injector 1 - C20-108
Injector 2 - C20-107
Injector 3 - C20-106
Injector 4 - C20-105
MAF+ - C20-118
MAF- - C20-116
The thing is, even for the injectors, C20-45 is listed next to all of them and I don't understand why? Enlighten me pleeeease. In the mean time, I need a beer. 🍻
... and aloe. 👎
Each injector has a common wire which is the POWER wire that goes directly to IGNITION +12V or else to the ecu 12V power (same condition). This is probably the C20-45. If you have a multimeter, do a continuity check from the injector common wire (this should have the same color on all injectors) to the positive terminal of the battery while ignition is on to confirm this.
The other injector wire is ground connected to individual ecu output ( in your case C20-105 to C20-108. The ecu activates the specific injector at a point in time by grounding these wires to make a complete circuit.
Regarding the MAF I cannot help you since I always work with MAP sensors which work with vacuum.
Fortunately for you I am almost doing a fresh engine management install so I am pretty sure I know this is the right route. So ask and I try to help you as much as I can.
IF you have an echo or yaris 2001 - 2005 the connectors on that manual do not match since I tried it myself. I didn't found a manual for mine so I had to cut all sensor wiring and connected them directly to the new ecu myself.
Thanks for the input guys. I definitely would like to hear from cdydjded on this.
I'll be doing a continuity check to confirm C20-45's function. However, it's clear that C20-105 to C20-108 are the wires that need to be intercepted for the injectors. At this point, I feel pretty confident I had the right wires so I think I'm gonna give it another shot. The only part that is unclear is which power source wire needs to be tapped. I doubt it matters though because both the conditions and specified conditions are the exact same.Originally Posted by Parmas ↑Each injector has a common wire which is the POWER wire that goes directly to IGNITION +12V or else to the ecu 12V power (same condition). This is probably the C20-45. If you have a multimeter, do a continuity check from the injector common wire (this should have the same color on all injectors) to the positive terminal of the battery while ignition is on to confirm this.
The other injector wire is ground connected to individual ecu output ( in your case C20-105 to C20-108. The ecu activates the specific injector at a point in time by grounding these wires to make a complete circuit.
Regarding the MAF I cannot help you since I always work with MAP sensors which work with vacuum.
Fortunately for you I am almost doing a fresh engine management install so I am pretty sure I know this is the right route. So ask and I try to help you as much as I can.
IF you have an echo or yaris 2001 - 2005 the connectors on that manual do not match since I tried it myself. I didn't found a manual for mine so I had to cut all sensor wiring and connected them directly to the new ecu myself.
When I hooked up the E-Manage blue I tapped into the 4 injectors and the common sensor ground wire. The power for the injectors should be coming from the EFI relay and fuse.
Got the FIC wired up today. I wired up the obvious power and grounds, along with injectors, tps sensor, and maf. Everything worked fine until I wired in the maf wires... The engine just kind of chugs and doesn't start. Interestingly, when I put the jumper harness in to bypass the FIC,it starts but I have a CEL. However, I think it has something to do with the TB as this literally just happened on friday when i disconnected the positive terminal of the battery for a prolonged time. It went away a few hours later.
Anyways, I'll be getting my 2.25" catback exhaust with a flowmaster super 44 tomorrow. I need to pick up some steel lines and adapters for oil return and feed. Also will be calling the tuner to talk a little more and setup an appointment.
Otherwise, I plan to begin the install wednesday and hope to have it done within 3 days time. Again, expect LOTS of pictures. I want to share the (hopefully) fun of the install with you fellow YWers 👍
Anyways, I'll be getting my 2.25" catback exhaust with a flowmaster super 44 tomorrow. I need to pick up some steel lines and adapters for oil return and feed. Also will be calling the tuner to talk a little more and setup an appointment.
Otherwise, I plan to begin the install wednesday and hope to have it done within 3 days time. Again, expect LOTS of pictures. I want to share the (hopefully) fun of the install with you fellow YWers 👍
You're sure you didn't hook the MAF up to the FIC backwards right? I know on the e-blue there was in from MAF and out to ECU.
Wow come to think of it... That definitely is it. I didn't think about it when I was wiring it up. Instead, I wired it exactly like the injectors... in from ECU, out to engine. I'll switch them tomorrow.
cdydjded, The only reason I hooked up the MAF wires/tps sensor was to potentially aid in tuning. I also thought it would allow me to avoid a CEL with the turbo in and running. However, the more I think about the setup of the Zage kit, I'm not sure if I'd even have a CEL. The MAF sensor goes before the turbo, and I'm keeping my stock o2 sensors. But wouldn't that throw out system too lean/rich codes?
cdydjded, The only reason I hooked up the MAF wires/tps sensor was to potentially aid in tuning. I also thought it would allow me to avoid a CEL with the turbo in and running. However, the more I think about the setup of the Zage kit, I'm not sure if I'd even have a CEL. The MAF sensor goes before the turbo, and I'm keeping my stock o2 sensors. But wouldn't that throw out system too lean/rich codes?
Was just combing through the Zage kit and noticed their turbocharger has 4 inlet/outlets (6 actually, 2 are welded). Could this possibly mean it can be water cooled? I don't know how to tell... I'll snap some pics of it tomorrow.
Reversed MAF wires and now the engine runs👍👍
Still have a CEL though... Gonna get the code read later.
Still have a CEL though... Gonna get the code read later.
3 attachments not included in this copy
can't wait to see you mount it up
Same here bro 👍Originally Posted by Yoda ↑can't wait to see you mount it up
I wasn't expecting to get a water cooled turbo, and I just got back from getting bolts to close the holes... I'll make a trip to home depot again early tomorrow and grab some nipples + lines to get it water cooled. Where would be the best place to tap the coolant lines?
I see your making big moves, the race is on. Chi-town vs. Jerezy
BRIIIING IT 😁Originally Posted by pimp my yaris ↑I see your making big moves, the race is on. Chi-town vs. Jerezy
I'll let you know that, despite what you may see on Jersey Shore, I am not a drunken and obnoxious waste of life and am capable of being productive. 😛
So far I'm thinking I'll use the TB coolant lines along with a tee to cool the turbo.
Did you pull the EFI fuse to clear the codes? And does it come on as soon as you start the car, or after it's been running for a while?Originally Posted by Focus_Sh1ft ↑Reversed MAF wires and now the engine runs👍👍
Still have a CEL though... Gonna get the code read later.
PS, you're welcome 😛
Exhaust is done and is LOUD, especially in the cabin. I'm gonna order some Dynamat, otherwise it's great 🙂
Here' some pictures of the illusive Zage kit to hold you guys over.
Picture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copy
Picture not included in this copyPicture not included in this copyPicture not included in this copy
And here's about half the additional stuff I bought that is needed for oil / water feed and return attachment, as well as others. Gonna throw the specs here that will be put in my future install guide:
2x 7/16" x 1 1/4" bolts (turbo)*
2x M8-1.25 x 40mm bolts (intercooler, could be shorter)
2x 1/8" x close fittings (oil feed+return)**
1x 3/8" female to 1/8" NPT female fitting (oil feed)
1x 1/2" male flare connector (extend feed line)***
2x 1/4" compression male to 1/4" NPT fitting (water, turbo outlets)
2x 1/4" NPT male to 1/4" barb (water... 5/16" couldn't be found)
3x 5/16" nylon tees (cooling turbo, BOV)
2x 5/16" dia. coolant tubing (turbo)
1x 5/16" dia. vacuum hose (BOV)
1x 1/2" fitting, 36" steel gas hose (oil feed, was all I could find, praying it works...)***
*Only need if water cooling isn't used.
**I wanted to use a 1/8" x 1 1/4" Nipple for the return fitting that gets welded into the block, but the threading appears to be problematic with the threaded tee in the Zage kit. I'll probably just use the 1/8" x close fitting. Shorter, but should work.
***Shouldn't actually be needed.
Picture not included in this copyPicture not included in this copy
Also would like to mention that my CEL, once again, disappeared on its own.
Here' some pictures of the illusive Zage kit to hold you guys over.
Picture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copy
Picture not included in this copyPicture not included in this copyPicture not included in this copy
And here's about half the additional stuff I bought that is needed for oil / water feed and return attachment, as well as others. Gonna throw the specs here that will be put in my future install guide:
2x 7/16" x 1 1/4" bolts (turbo)*
2x M8-1.25 x 40mm bolts (intercooler, could be shorter)
2x 1/8" x close fittings (oil feed+return)**
1x 3/8" female to 1/8" NPT female fitting (oil feed)
1x 1/2" male flare connector (extend feed line)***
2x 1/4" compression male to 1/4" NPT fitting (water, turbo outlets)
2x 1/4" NPT male to 1/4" barb (water... 5/16" couldn't be found)
3x 5/16" nylon tees (cooling turbo, BOV)
2x 5/16" dia. coolant tubing (turbo)
1x 5/16" dia. vacuum hose (BOV)
1x 1/2" fitting, 36" steel gas hose (oil feed, was all I could find, praying it works...)***
*Only need if water cooling isn't used.
**I wanted to use a 1/8" x 1 1/4" Nipple for the return fitting that gets welded into the block, but the threading appears to be problematic with the threaded tee in the Zage kit. I'll probably just use the 1/8" x close fitting. Shorter, but should work.
***Shouldn't actually be needed.
Picture not included in this copyPicture not included in this copy
Also would like to mention that my CEL, once again, disappeared on its own.
Lemme also add what I now know about this kit after looking it over carefully.
-There are no bolts to attach the intercooler
-If using a sandwich adapter to feed the turbo, some adapters nuts will be needed
-I don't know what they expect you to do with the feed tbh. I think that's up to the user, but the amount of steel braided line included won't be getting you anywhere. *I had the lines mixed up. This shouldn't be a problem.
-The BOV has a bypass, but 1/4" rubber hosing is (obviously) needed but not included. A plug is included to close the bypass (but using the BOV and not the bypass is stupid).
-The turbo, to my surprise, can be water cooled (which means my turbo timer will only be good for pretty lights 😁). However, there are no bolts, nipples, or even hoses included to make use of it. In fact, there aren't even additional bolts to close the holes.
-I'm PRETTY SURE the actuator can be adjusted to add/subtract boost.
-The Downpipe has 1 bung for the stock o2, and one with a removable plug.
-The Turbo has 2 welded holes (what could they be used for?).
As you can see, this kit is already far from a full bolt-on (although I don't think Zage ever claimed it to be). However, with some additional stuff and some guidance, it has the potential to be. I had some prior obligations today so I got kind of sidetracked... At this point though, I'm pretty sure all I need is some lines for the coolant. I didn't realize fuel lines wouldn't hold up, as the coolant will eat right through them apparently.
-There are no bolts to attach the intercooler
-If using a sandwich adapter to feed the turbo, some adapters nuts will be needed
-I don't know what they expect you to do with the feed tbh. I think that's up to the user, but the amount of steel braided line included won't be getting you anywhere. *I had the lines mixed up. This shouldn't be a problem.
-The BOV has a bypass, but 1/4" rubber hosing is (obviously) needed but not included. A plug is included to close the bypass (but using the BOV and not the bypass is stupid).
-The turbo, to my surprise, can be water cooled (which means my turbo timer will only be good for pretty lights 😁). However, there are no bolts, nipples, or even hoses included to make use of it. In fact, there aren't even additional bolts to close the holes.
-I'm PRETTY SURE the actuator can be adjusted to add/subtract boost.
-The Downpipe has 1 bung for the stock o2, and one with a removable plug.
-The Turbo has 2 welded holes (what could they be used for?).
As you can see, this kit is already far from a full bolt-on (although I don't think Zage ever claimed it to be). However, with some additional stuff and some guidance, it has the potential to be. I had some prior obligations today so I got kind of sidetracked... At this point though, I'm pretty sure all I need is some lines for the coolant. I didn't realize fuel lines wouldn't hold up, as the coolant will eat right through them apparently.
The other port on the downpipe, the picture isn't too clear, but it looks like there is a plug in the other one that can be removed / unscrewed and is not the full size of the bung. Should be able to take it out and put a wideband sensor there.
The plugs on the turbo are usually secondary coolant locations for the feed i beleive, my K04s come with one on the side, depending on where I get the turbo, I need to swap the plug to the other one.
Some things that aren't included in the kit seem just a minor inconvenience as long as everything else bolts up.
Cracking pressure is cracking pressure you can make it harder to open to increase tension on the rod, but spring rate is spring rate inside the actuator housing itself. Use a boost controller if you want to raise boost the way it is setup now is so it opens with cracking pressure. probably preset anywhere from 6-10psi.
The plugs on the turbo are usually secondary coolant locations for the feed i beleive, my K04s come with one on the side, depending on where I get the turbo, I need to swap the plug to the other one.
Some things that aren't included in the kit seem just a minor inconvenience as long as everything else bolts up.
Cracking pressure is cracking pressure you can make it harder to open to increase tension on the rod, but spring rate is spring rate inside the actuator housing itself. Use a boost controller if you want to raise boost the way it is setup now is so it opens with cracking pressure. probably preset anywhere from 6-10psi.
Why in the world would they weld the 2nd bung shut, instead of threading an insert into it?
Otherwise, not too bad so far! Keep going!
Otherwise, not too bad so far! Keep going!
Sorry guys, you're right, I totally missed it. The second bung on the downpipe has a removable plug. The turbo though... I still don't think the plugs are removable, but I guess it's irrelevant.
Here's day one of the install. I got stuck A LOT... but only because I lacked the necessary tools. Hoping tomorrow will be slightly more productive.
Engine Before Pics
Picture not included in this copyPicture not included in this copy
Pics of everything being installed to the Turbo
Picture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copy
Exhaust Manifold + o2 sensor
Picture not included in this copyPicture not included in this copy
Picture not included in this copyPicture not included in this copyPicture not included in this copy
And now, here's two reasons I believe Zage has been known for exploding turbos.Picture not included in this copyPicture not included in this copy
Basically, the above bolt goes into the oil feed spot on the turbo, and the bolt in the second picture has a loop on the end that goes around the first bolt. They both have little holes drilled in them that allow the oil through (sorry no pictures, wish I had). I personally think it's a crummy design and could very well be problematic. The only plus is that the feed adapter can be adjusted slightly, but what for? A simple elbow would have sufficed...
Here's my current snag. I have everything attached to the turbo, such that I can mount it up to the engine block and then run the lines to the appropriate places. However, and I dare say, this may be where the alleged "fitment issue" comes into play. There's no way in hell I can fit this thing in (and don't say take everything off because the difference will be minimal). I removed the fuel hose, and thought I could move the AC lines. A ton of air/gas spewed out and I couldn't stop it by rebolting it. COULD ANYONE CLARIFY WHAT THIS WAS? I believe it was just compressed air, but I know little regarding AC lines. Basically, once it's in it won't be a problem. But the AC lines are REALLY in the way currently.
Engine Before Pics
Picture not included in this copyPicture not included in this copy
Pics of everything being installed to the Turbo
Picture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copyPicture not included in this copy
Exhaust Manifold + o2 sensor
Picture not included in this copyPicture not included in this copy
Picture not included in this copyPicture not included in this copyPicture not included in this copy
And now, here's two reasons I believe Zage has been known for exploding turbos.Picture not included in this copyPicture not included in this copy
Basically, the above bolt goes into the oil feed spot on the turbo, and the bolt in the second picture has a loop on the end that goes around the first bolt. They both have little holes drilled in them that allow the oil through (sorry no pictures, wish I had). I personally think it's a crummy design and could very well be problematic. The only plus is that the feed adapter can be adjusted slightly, but what for? A simple elbow would have sufficed...
Here's my current snag. I have everything attached to the turbo, such that I can mount it up to the engine block and then run the lines to the appropriate places. However, and I dare say, this may be where the alleged "fitment issue" comes into play. There's no way in hell I can fit this thing in (and don't say take everything off because the difference will be minimal). I removed the fuel hose, and thought I could move the AC lines. A ton of air/gas spewed out and I couldn't stop it by rebolting it. COULD ANYONE CLARIFY WHAT THIS WAS? I believe it was just compressed air, but I know little regarding AC lines. Basically, once it's in it won't be a problem. But the AC lines are REALLY in the way currently.
What came out of your Ac lines was R134a, and actually since its escaped the lines your a criminal. Its illegal to vent it into free air( ie not into a container). But I wont report you cause you didnt know. lol 😁 Now your ac wont work until you recharge it and maybe replace a few seals.
But on the bright side, if you can remove the lines from the engine bay you wont cause anymore harm to the ac system. And if you can remove the lines you hopefully wont have anymore clearance issues.
Edit: I was just messin bout the criminal thing. Wanted to clarify that before it could get out of hand. It is illegal but I cant say I havent done it myself.
But on the bright side, if you can remove the lines from the engine bay you wont cause anymore harm to the ac system. And if you can remove the lines you hopefully wont have anymore clearance issues.
Edit: I was just messin bout the criminal thing. Wanted to clarify that before it could get out of hand. It is illegal but I cant say I havent done it myself.
It was most likely freon, I hope you stepped away and didn't breathe any in. It is known to be harmful and cause cancer in some studies.
You are right, that Oil feed looks a little weird and there should be a better way, but that will work.
You look like you are making good progress, keep it going!.
If you are having fitment issues, I would just try to fit the turbo and manifold in at once without the downpipe on since you can get that in later, it may allow for easier rotationability that would help you out squeezing it in there?
You also may need to reclock the turbo, atleast the cold side since you manage where your lines are going. I can't see how that one reclocks but most likely if theres no bolts or collar theres a C Clip in there.
You can always take a couple of pliers and add force to bend the lines out the way a little bit, or just run no AC :P I dunno what the temps were in Jersey this year.
MORE PICS!
You are right, that Oil feed looks a little weird and there should be a better way, but that will work.
You look like you are making good progress, keep it going!.
If you are having fitment issues, I would just try to fit the turbo and manifold in at once without the downpipe on since you can get that in later, it may allow for easier rotationability that would help you out squeezing it in there?
You also may need to reclock the turbo, atleast the cold side since you manage where your lines are going. I can't see how that one reclocks but most likely if theres no bolts or collar theres a C Clip in there.
You can always take a couple of pliers and add force to bend the lines out the way a little bit, or just run no AC :P I dunno what the temps were in Jersey this year.
MORE PICS!
Quick question. Is the zage kit cheaper then piecing it together? Wanting to go turbo soon and trying to make a plan.
I figured it was the AC coolant, but was confused because it didn't burn... Nor did I die 😁Originally Posted by coheed ↑What came out of your Ac lines was R134a
Any info on how to recharge this and seal it? I couldn't figure out how to close the leak, and I didn't see any o-rings or gaskets on the lines. I would like to use the AC again sometime soon though lol.
On the plus side, I think I'll make the best of a somewhat crappy situation and tear those suckers out temporarily to give me the needed clearance.
Nexus, I was toying with the idea of pulling the downpipe off, but I believe it's going to be near impossible to bolt it on once it's in the engine. If the above doesn't work, that'll be next though.
Oh and coheed, I'm not entirely sure which is cheaper. I can tell you right now the Zage kit runs at $1800 and, so far, has only needed some additional bolts and brass fittings. I think pimp my yaris is up to nearly $1000 on his custom install and still has a couple things left to buy. Keep a close eye on the two of us 👍
Your local Autozone should carry a recharge/ sealant kit for under $30. Me and a buddy just did his integra in his front yard with no tools. Really easy to do.
And you are an inspiration to me. i want to do this to mine so bad but have no funds right now. 👎
And you are an inspiration to me. i want to do this to mine so bad but have no funds right now. 👎
Thanks a bunch man. I just looked it up as well and it looks easy peesy. Just gotta figure out how to reseal where it leaked out... I'm thinking a man by the name of Mr. J.B Weld might just have a solution for me 👍Originally Posted by coheed ↑Your local Autozone should carry a recharge/ sealant kit for under $30. Me and a buddy just did his integra in his front yard with no tools. Really easy to do.
And you are an inspiration to me. i want to do this to mine so bad but have no funds right now. 👎
And thanks even more for the vote of confidence, I feel a little beat up after today lol. Not having the right tools sucks, but that's sorted out now. I barely had the funds to do this and was hesitant because turbocharging this car is, for the most part, still a mystery.
Methinks you should keep your pants on for the time being, and be the first user of my ultimate Zage turbo install guide. It's already in the works 😉
It's going to have pre-install installs as well, such as the FIC, Apexi turbo timer, gauges, and whatever else I think of. I'd be pretty happy to get this car to be a little more popular in the forced induction category (or atleast recognized by tuning / exhaust shops lol).
I get the concept... I think, but shouldn't this have been done out of factory? Are you saying I should check it just to be safe?Originally Posted by Nexus1155 ↑You also may need to reclock the turbo
I'm just saying that because I don't know where you are getting stuck with it or where you are going to have the charge piping run. You always want things facing the easiest way
I think I am gonna go this route. The way I was thinking previously was piecing it. But that would've included a cheapo ebay turbo my friend has. And the zage one being water and oil cooled has pretty much swayed me. But Im also leaning more to eManage ultimate because one of my friends already has the software and some tuning expirience with it.Originally Posted by Focus_Sh1ft ↑Methinks you should keep your pants on for the time being, and be the first user of my ultimate Zage turbo install guide. It's already in the works 😉
It's going to have pre-install installs as well, such as the FIC, Apexi turbo timer, gauges, and whatever else I think of. I'd be pretty happy to get this car to be a little more popular in the forced induction category (or atleast recognized by tuning / exhaust shops lol).
I was also not able to install the turbo and manafold in the car as an assembly. A/C lines were in the way as well. I lowered the turbo behind the engine and let it sit on the K-frame. Then I bolted up my manafold and reached around the manafold and lifted the turbo to it. Then slide the tubo onto the studs and bolt it down. It was the only way to get it all in there without removing the A/C lines. It looks like your turbo will attach to mani with bolts. This might make it easier.
Are you guys working from above? When we did my first kit, we removed the subframe and worked from below.
Interesting, how hard would that be? Doing this would most likely make it easier to route some of the piping as well.Originally Posted by cali yaris ↑Are you guys working from above? When we did my first kit, we removed the subframe and worked from below.
I was thinking of watching some porn tonight but now I don't need to :D great job so far, gonna follow this thread closely!!
I was thinking of watching some porn tonight but now I don't need toGood. Send it back, please.
Haha, if you want porn I should show you how cut up my hands currently are.Originally Posted by eTiMaGo ↑I was thinking of watching some porn tonight but now I don't need to :D great job so far, gonna follow this thread closely!!
And now, here's day two of the install. Lot's of annoying things to slow me down (including work 🙄). Just wanna point out that I had to change cameras, and this one isn't as good. I'll try to get the other back for Sunday. Anyhoo...
AC lines couldn't come out, so I moved them to the side a bit. Turns out there was an o-ring. Guess what? It blew.
Picture not included in this copy
However, there were two issues that were such a pain in the ass to get off...
Picture not included in this copyPicture not included in this copy
Picture not included in this copy
Both of these mounts were part of the OEM header assembly. However, they were totally in the way of the Zage downpipe.
Here's the turbo/mani/downpipe with lines attached finally fitting in.
Picture not included in this copy
The money shots...
Picture not included in this copyPicture not included in this copy
From the bottom
Picture not included in this copy
First intercool pipe added
Picture not included in this copyPicture not included in this copy
As you can see from the above, downpipe fitment is PERFECT. Well, except for this one problem.
Picture not included in this copy
Turns out the OEM downpipe bolt on the right side begins to hit the downpipe. No problem, it was a quick fix with a hacksaw and power sander.
Picture not included in this copyPicture not included in this copy
So here's the recap and where I'm at. Thus far, everything has fit perfectly. The only complaint I have is how impossible it is to get the bolts on the manifold tight. I can't get any type of wrench on them because the manifold blocks access from all directions. I can't even think of a tool that could be used, so I'm open to suggestions. The other potential issue I may have is the fitment problems of one of my coolant adapters on the turbo. This is not Zage's fault. For whatever reason, one of my compression nuts doesn't want to thread properly. I threaded it as much as possible and JB welded it. Nervous, but won't know until the car is running.
I also am unsure as to whether or not the feed line is going to make it to my sandwich adapter, but that's no biggie I suppose. Otherwise, my only other concern with the Zage kit beside the mani bolt issue is the intercooler piping. I sat for awhile today trying to figure out how the hell there's enough piping to run from the turbo all the way around to the TB. In particular, it seems like there could very well be a piece of piping that is missing. I'll be looking into this more.
Just remembered. I was a little concerned about the return line as well for two reasons. Now that everything is mounted up and I've seen the line run to where it would be IF I was using the Zage oil pan, I now understand it's problem. cdydjded was right - the return is a TERRIBLE design. The line would run horizontally to one side of of the oil pan to the back corner on the other side, whereby it would bolt in. That aside, even with my plan to tap the block above the pan I still am in a tough spot. The return line is too long and rigid to tap approximately where Garm tapped (pictures a few pages back). I'm gonna need another spot somewhere near there... I think I just need to spend some time looking at it.
Otherwise, everything is going pretty well so far. I thought I would be progressing along a little quicker but not only am I pretty inexperienced, I really would like to get this right and working.
EDIT: Just looked at their install pictures. I think I understand how they did the piping, but I believe they removed sections of plastic / metal (not sure what it is atm) next to the radiator (at the bottom) to work it around.
Very nice progress. Lol Ive been checking here all day waiting for the update. How much did you have to cut off of the bolt for it to clear the down pipe?
Looking at the Zage website Id say your not missing any ic piping. Thats a bummer.
Looking at the Zage website Id say your not missing any ic piping. Thats a bummer.
Living vicariously through others. Nice. 👍Originally Posted by coheed ↑Lol Ive been checking here all day waiting for the update.
I only cut off about 1/4" of that bolt, but even that gave me more than enough room. The really annoying part was removing those two black frame pieces... It was nearly impossible to get a socket on them and give them enough torque to get em moving.
Lol I have no life right now. No job and waiting for school to kick back up.Originally Posted by Focus_Sh1ft ↑Living vicariously through others. Nice. 👍
Boredom ftl 🤣
Waiting for school to start back up is never a good thing. 😛
I'm glad I'm keeping you entertained lol. Expect a solid 8 hours of work (and pictures) on this on Sunday.
I'm glad I'm keeping you entertained lol. Expect a solid 8 hours of work (and pictures) on this on Sunday.