Replies continued
Focus_Sh1ftThread starterNew Jersey · Dec 9, 2012#401Ok, cracked open the ECM. Two things worth talking about.
First, pretty sure I pushed a cap off one of the pads lol. Oops. Easy enough to fix though.
Picture not included in this copy
This was a lot more noticeable... I don't think i knocked this out of place. Regardless, WHAT IS THIS. I've done quite a bit of work on electronics but never seen something like this before. (Bottom right corner, next to white square)
Picture not included in this copy
Otherwise, things look good...
yaris2010RSAngus, Ontario · Dec 9, 2012#402oooooo.... that doesnt look good, im sure CTScott will be able to tell you what that is.
glad to see you got into your ECM and it sounds alot like the same issues i was having. If you learned anything from my thread, dont drive it too much.
Also just a side note, check your blowby from the breather tube. 2 years boosted with no serious problems? congrats man and knock on wood. I like to think i would have made it 2 years if i didnt have my ECM issues.
also when was the last time you did a tune up? fuel system cleaner and spark plugs? when my car was acting up i did a tune up and it got better so that was definatly a contributing factor
Focus_Sh1ftThread starterNew Jersey · Dec 9, 2012#403Spark plugs are (were) only a little over a year old. I actually just bought seafoam for the first time.
Not driving at all until this is solved. Just watching the car idle makes me cringe and I don't want to leave it running long during troubleshooting lol...
Definitely going to shoot CTScott a PM. How did that part look on your ECM (if you remember)? It sits between two traces but doesn't look like it should bridge them 🤷
yaris2010RSAngus, Ontario · Dec 9, 2012#404ill look through the pics in my phone and see if i caught that in one..... If i wasnt out of propane for my garage heater and it wasnt so damn cold in my garage id go and open up my new ECM lol.
Focus_Sh1ftThread starterNew Jersey · Dec 9, 2012#405Yeah, that whole winter thing. Hate it.
I'm praying this is related. The only thing I HAVEN'T checked is fuel pressure, which is going to be a pain. From what I can see it's going to have to be done out of the sender assembly because I don't have fittings for hookup in the engine bay...
yaris2010RSAngus, Ontario · Dec 9, 2012#406TaDa!
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
yaris2010RSAngus, Ontario · Dec 9, 2012#407use the white square label as a reference
Focus_Sh1ftThread starterNew Jersey · Dec 9, 2012#408Holy SHIT. That might just be the problem......
And by might be the problem, I mean DEFINITELY is the problem.
You sir. THANK YOU.
yaris2010RSAngus, Ontario · Dec 9, 2012#409what happened to yours? lol, it doesnt look burnt.....
yaris2010RSAngus, Ontario · Dec 9, 2012#410y did we move back to your thread? my thread is only 7 pages, yours in 25......
Focus_Sh1ftThread starterNew Jersey · Dec 9, 2012#411I wish I knew. Hopefully it didn't happen while trying to open the ECM. There isn't really any marks around it though (the cap had a bunch).
Tomorrow I'll resolder the cap and throw the ECM back in the car and make sure I get the same result.
Either way, looks like the ECM needs replacement lol. But hey, if I've finally found the problem I'm incredibly relieved.
yaris2010RSAngus, Ontario · Dec 9, 2012#412i would imagine its just some type of diode, im sure you could fix this yourself (maybe wait for CTScotts input on this)
Focus_Sh1ftThread starterNew Jersey · Dec 9, 2012#413That would be great. My only concern would be figuring out the correct specs.
Tomorrow should be an interesting day. Hopefully one that see me driving the Yaris again and not borrowing my mom's Sienna lol -.-
yaris2010RSAngus, Ontario · Dec 9, 2012#414you had to resolder the cap back on? dude that sucks.......
did you find any loose pieces from it in the ECM case?
PM me if you need the numbers off that component, id open up my ECM for ya. (and im waiting for a reason to open mine up and cover it with di-electric grease and properly reseal it
CTScottUSA, CT · Dec 9, 2012#415The obliterated device is a large diode. The markings on it are "T3 81". If you would like I can pull the one off of the ECM in the picture below and send it to you. I have been using this ECM as a sacrificial lamb for people needing components.
Picture not included in this copy1 attachment not included in this copy
Focus_Sh1ftThread starterNew Jersey · Dec 9, 2012#416Great news! Threw the ECM back in the car and we still have the same problems! (I must live a pretty depressing life if I consider that 'good news' 😛 )
The obliterated device is a large diode. The markings on it are "T3 81". If you would like I can pull the one off of the ECM in the picture below and send it to you. I have been using this ECM as a sacrificial lamb for people needing components.
CTScott - is there ever a time you don't pull through? lol
Are the markings significant to you? I ask for two reasons. One: could I possibly pick up an equivalent diode at a local electronics store? Two: I noticed yaris2010RS has what looks like 'T3 91'. Wondering if there's any substantial differences. For reference, my ECM is for a 2008 automatic (part# 89661-52G50).
If all else fails, I'll gladly take you up on your generous offer. Thanks again!
yaris2010RSAngus, Ontario · Dec 9, 2012#417CTScott i wished toyota let me keep the old ECM as i would have loved to donate it to you
CTScottUSA, CT · Dec 9, 2012#418 Originally Posted by
Focus_Sh1ft ↑ Great news! Threw the ECM back in the car and we still have the same problems! (I must live a pretty depressing life if I consider that 'good news' 😛 )
CTScott - is there ever a time you don't pull through? lol
Are the markings significant to you? I ask for two reasons. One: could I possibly pick up an equivalent diode at a local electronics store? Two: I noticed yaris2010RS has what looks like 'T3 91'. Wondering if there's any substantial differences. For reference, my ECM is for a 2008 automatic (part# 89661-52G50).
If all else fails, I'll gladly take you up on your generous offer. Thanks again!
The 81/91 are likely date codes and the T3 is the identifier.
It appears to be a BAV19W - BAV21W:
http://www.diodes.com/datasheets/ds12024.pdf Focus_Sh1ftThread starterNew Jersey · Dec 9, 2012#419Unfortunately, since these look to be used largely for commercial use, obtaining one (or even a few) looks pretty impractical.
I was trying to match some typical diodes found at a place like radioshack against the electrical characteristics in that link, but no luck.
Getting the piece from you looks like the best way to proceed. I'll send you my info shortly.
Also: Is anyone as baffled as myself as to how this happened? Technically I've been running the ECM in "limp mode," so maybe that circuit was spending too much time outside it's expected operational range or something? Weird.
yaris2010RSAngus, Ontario · Dec 9, 2012#420my bet is water.......
Ill check tomorrow at a local electronics surplus store. Radioshack wont have anything like this, you need to go to a real electronics store....
CTScottUSA, CT · Dec 9, 2012#421Pulled, packed, and ready to head to the post office in the morning:
Picture not included in this copy1 attachment not included in this copy
Bluevitz-rsOshawa, Ontario, Canada · Dec 9, 2012#422Focus_Sh1ftThread starterNew Jersey · Dec 10, 2012#423 Originally Posted by
CTScott ↑ Pulled, packed, and ready to head to the post office in the morning:
Attachment 49257
Excellent. 😁
So I discovered something interesting while digging around. Apparently, the 2008 model year switched ECM models only two months into production. Common sense says Toyota must have found something pretty bad to merit changing the ECM during the production run, rather than waiting for the following year.
CTScottUSA, CT · Dec 10, 2012#424 Originally Posted by
Focus_Sh1ft ↑ Excellent. 😁
So I discovered something interesting while digging around. Apparently, the 2008 model year switched ECM models only two months into production. Common sense says Toyota must have found something pretty bad to merit changing the ECM during the production run, rather than waiting for the following year.
Which part number ECM do you have? Looking at the EPC, for AT equipped Yaris only there was a change in 11/2007, with the build having started in 8/2007.
Focus_Sh1ftThread starterNew Jersey · Dec 10, 2012#425^ That's exactly what I'm talking about. I have 89661-52G50 and they started using 89661-52G51 in 11/07. Haven't been able to find anyone else with ECM failures though, but then again that is a fairly small window.
CTScottUSA, CT · Dec 10, 2012#426 Originally Posted by
Focus_Sh1ft ↑ ^ That's exactly what I'm talking about. I have 89661-52G50 and they started using 89661-52G51 in 11/07. Haven't been able to find anyone else with ECM failures though, but then again that is a fairly small window.
Crashy and Crashy 2 both have the 89661-52G50. The outer aluminum of Crashy's ECM is super oxidized. I really should open it to see if any of the salt has made its way inside yet. There wasn't a TSB on the change, so the 89661-52G51 isn't considered a necessary replacement, so they probably did some minor tweaking to the AT control, since the MT didn't get revved.
Focus_Sh1ftThread starterNew Jersey · Dec 12, 2012#427Leave it to USPS to take what should have been 1 day shipping and turn it into what is going to be at least 3 days now. Ugh.
CTScottUSA, CT · Dec 12, 2012#428 Originally Posted by
Focus_Sh1ft ↑ Leave it to USPS to take what should have been 1 day shipping and turn it into what is going to be at least 3 days now. Ugh.
Tracking shows that it was delivered today.
Focus_Sh1ftThread starterNew Jersey · Dec 12, 2012#429Oh boy.
Focus_Sh1ftThread starterNew Jersey · Dec 13, 2012#430Welp, this board is dead. Diode made no difference (yes I observed polarity).
Let's talk about replacement ECMs. My number one concern is if I'm going to need reprogramming or not. From what I understand, since I don't have an immobilizer I shouldn't need it. I'll have a VIN mismatch obviously but I'm pretty over that.
Also probably going to grab a part# 89661-52G51 since they're more available.
Bluevitz-rsOshawa, Ontario, Canada · Dec 13, 2012#431Well that's sucks! I gues you just need a non Imobilizer ECU as a replacement then.
yaris2010RSAngus, Ontario · Dec 14, 2012#432from what i have gathered from a mechanic (chrysler but same thing), you will be able to switch it out without issue. if you have keyless entry (lock and/or unlock on your key fob) you may need to reprogram this feature. he said it depends on the specific car. (Im sure CTScott would be able to answer that)
As per the chip key thing, has anyone confirmed that a new ECM would need this programmed in? from what my dash cam caught of My ECM replacement they did not program any keys (nor did they ask/ensure i had all my keys with me). They may have transferred the data off my old one onto my new one but i am not sure
CTScottUSA, CT · Dec 14, 2012#433 Originally Posted by
Focus_Sh1ft ↑ Welp, this board is dead. Diode made no difference (yes I observed polarity).
Let's talk about replacement ECMs. My number one concern is if I'm going to need reprogramming or not. From what I understand, since I don't have an immobilizer I shouldn't need it. I'll have a VIN mismatch obviously but I'm pretty over that.
Also probably going to grab a part# 89661-52G51 since they're more available.
With a non transponder key one the only thing that ideally needs to be programmed is the VIN. This can be done via techstream. If you don't have it done, if your state does an inspection or emissions check, where they plug into the OBD connector, the VIN will read incorrectly.
If you don't want to deal with the dealer for the VIN reprogram, ship me the ECM and I'll program it for you.
cali yarisCanoga Park, CA · Dec 14, 2012#434Will you smog and pass my car next March? 😆
Focus_Sh1ftThread starterNew Jersey · Dec 17, 2012#435Got the new ECM today and it did absolutely NOTHING. I have the same problem... I even opened it up to see if it failed in the same way thinking maybe a short in the harness. It was fine.
I'm losing my mind over this... The only things left to check are the integration relay and fuel pressure.
Anyone else have any other ideas? Once I rule those two out, I really don't know what else to do...
CTScottUSA, CT · Dec 17, 2012#436 Originally Posted by
Focus_Sh1ft ↑ Got the new ECM today and it did absolutely NOTHING. I have the same problem... I even opened it up to see if it failed in the same way thinking maybe a short in the harness. It was fine.
I'm losing my mind over this... The only things left to check are the integration relay and fuel pressure.
Anyone else have any other ideas? Once I rule those two out, I really don't know what else to do...
Are you running a F/IC, or just the ECM by itself?
Focus_Sh1ftThread starterNew Jersey · Dec 17, 2012#437I've tried both. I can't find anything wrong physically in the FIC harness either. Maybe I should do continuity checks on the connector side?
yaris2010RSAngus, Ontario · Dec 17, 2012#438^thats very very odd.....
Just a shot in the dark here, try to run on stock injectors and ECM (no FIC). just to rule out injectors and FIC.
Im sorry to say it sounds alot like the issues i was having. check what your blow by pressues are like at the breather tube.
Also im not sure how plausible this is but could you be having an issue with your stock O2 sensor? if not the sensor possibly the wiring touched the exhaust and melted. Possibly try to unplug the O2 to see how the car reacts.
Bluevitz-rsOshawa, Ontario, Canada · Dec 17, 2012#439Now that I think about it, I forgot the Yarisworld uses an AFR sensor not an o2 sensor up front. So it might really depend on that sensor to make quick adjustments. If the sensor is indeed out of calibration or reading slow it could be causing the lean rich condition.
Focus_Sh1ftThread starterNew Jersey · Dec 17, 2012#440Thanks for your thoughts guys.
I do agree it's very possible my afr sensor is bad, but like I've said it's completely irrelevant because open loop is running like garbage. However, I've decided to just get a new one tomorrow and go back to closed loop to continue troubleshooting. I need to eliminate whatever variables I can.
I'm hoping maybe with a new afr sensor and closed loop I'll be able to get the car running good enough to complete a few drive cycles. At this point it looks like I really need code(s) to point me in the right direction.
Just a shot in the dark here, try to run on stock injectors and ECM (no FIC). just to rule out injectors and FIC.
I run stock injectors at all times, and they check out because all four plugs are getting fouled. Also, I don't have a boomslang, so the best I can do is use the bypass plug and take the FIC out of the equation (which I've been doing).
I'll check the breather tube. There hasn't been any smoking out of it though.
Ironic aside: I just made my last payment on the car a week ago. Funny or depressing, you decide.
Focus_Sh1ftThread starterNew Jersey · Dec 17, 2012#441Here's a summary of what's been done thus far.
x Air induction system --- triple checked
x Injector blockage/leakage --- ALL plugs fouled
x Coils --- throws immediate codes; none thrown
x Plugs --- used three different sets of plugs with varying gaps
x Throttle plate sticking
x MAF meter --- replaced
x ECT sensor --- readings fine
x Gas leakage from exhaust system
x Rear O2 --- pulled; no difference
x PCV hose connections --- no vacuum leaks
x PCV valve
x ECM --- replaced
x Stuck valve --- compression: 195, 195, 205, 205
x FIC --- bypassed or not, runs the same
x Bad gas --- added fuel stabilizer
x A/F sensor (sensor 1) --- replaced
x Integration relay
x Fuel pressure
Bluevitz-rsOshawa, Ontario, Canada · Dec 17, 2012#442Do you know for 100% that the ECU isn't still looking at the AFR sensor when in both open or closed loop. Because simply disconnecting it will just cause the sensor input to put into default values.
Focus_Sh1ftThread starterNew Jersey · Dec 18, 2012#443I can't say for certain, but I've always been under the impression that with the AFR sensor pulled and unplugged, fueling is done using predetermined values based on other sensor data (MAF, ECT, IAT, crank/cam signal, etc.). Scangauge, for whatever reason, doesn't allow you to view A LOT of the OBDII protocol including oxygen sensor information.
yaris2010RSAngus, Ontario · Dec 18, 2012#444just pull the plug on your 1st O2, im not 100% it doesnt use that reading even in open loop. i would ensure its not reading it.
Injector blockage/leakage --- ALL plugs fouled
what does this mean? are you rulling out injector issues based on the plugs not being fouled? from what your describing, it sounds like it could be an injector sticking issue.
Focus_Sh1ftThread starterNew Jersey · Dec 18, 2012#445No, all four plugs are getting fouled. Even though the afrs are running from super rich to super lean, they're generally on the rich side (especially in open loop). There's no way all four injectors are suddenly sticking. I'd also expect to see a slightly higher compression in one cylinder from carbon buildup.
Also, to be clear, when I run open loop my afr sensor is NOT plugged into the harness and NOT downstream. Therefore no values are being read.
Even though the ecm is ruled out, I still can't get over the nagging feeling that this is somehow electrical (I checked all fuses BTW)...
Focus_Sh1ftThread starterNew Jersey · Dec 18, 2012#446Didn't realize front O2 sensors are $160... For a part I don't even need. Ugh -.-
CTScottUSA, CT · Dec 18, 2012#447 Originally Posted by
Focus_Sh1ft ↑ Didn't realize front O2 sensors are $160... For a part I don't even need. Ugh -.-
You can get the generic Denso 2349052 for under $100.
cali yarisCanoga Park, CA · Dec 18, 2012#448Or one off my shelf. 🙂
GolddeenohColumbia, SC · Dec 18, 2012#449oh now Garm says he has one. :P
Focus_Sh1ftThread starterNew Jersey · Dec 18, 2012#450Bleh, I was using a different denso part number and was only turning up $130 at best. Oh well.
So yeah, no big difference with it in. Car spends a bit more time around stoich but continues to trend toward the lean side. Also, integration relay and PCV valve are fine.
I'm gonna have my mechanic smoke test the intake tomorrow and see if he has any other ideas. I did a typical boost leak test and the intake did hold some pressure, but all symptoms still point to a vacuum leak. Definitely need some peace of mind on this. It's a lot more plausible than something going wrong with a completely stock, completely untouched fuel regulator.
If not, I'm going to drive it enough to complete some drive cycles. I see no other options.