I NEED Boost... Opinions puh-lease
517 posts · 111,381 views · page 8 of 11
Replies continued
Yes Garm, I mentioned you! My guru. lol. Bring those zage kits in! Let's do this
haha "Guru", I just learned from other people, I think we all do.
Focus, no one ever asked a question about boost controllers before.
"the truth is out there" -- if you know how to Google. 😁
Focus, no one ever asked a question about boost controllers before.
"the truth is out there" -- if you know how to Google. 😁
I have a bit of a conundrum...
My car is stuck in open loop all of the sudden. I have no idea why it is, but now I can't boost because it goes LEAN. Anyone have any ideas why it suddenly decided to stay in open loop? My thought is it has something to do with driving cycles and the ECU seeing boost, as this is the longest I've driven without pulling terminals off the battery. I'm sure I could probably do just that and it would reset, but this is certainly a curious case. No CELs either, and my turbo timer is getting feedback from the AFR sensor still.
My car is stuck in open loop all of the sudden. I have no idea why it is, but now I can't boost because it goes LEAN. Anyone have any ideas why it suddenly decided to stay in open loop? My thought is it has something to do with driving cycles and the ECU seeing boost, as this is the longest I've driven without pulling terminals off the battery. I'm sure I could probably do just that and it would reset, but this is certainly a curious case. No CELs either, and my turbo timer is getting feedback from the AFR sensor still.
Ok this situation is baffling, but incredibly awesome. My car is still doing the same thing. I pulled the AFR plug just to make sure the ECU throws a CEL, and it does. So... Something is happening that's forcing the car into open loop without any CELs! This is an optimal situation, and I wish I could figure out why it's happening for future reference. I have no idea where to even begin looking though.
I'm going to just tune the car instead of resetting the battery. If it swaps back to closed loop at some point - no biggie.
EDIT: As soon as I plugged my FIC back in and started the car, the issue resolved itself. I'm still clueless as to what I just witnessed, but I would love to find out. There must have been some criteria the engine failed to meet to throw itself into closed loop. The catch would seem that whatever it is doesn't cause a code though...
Oh and also - I was reading the service manual and noticed the AFR sensor heater operates between .9 and 10 Amps. A code is thrown if the current drops below .8A. Could it be possible to greatly limit the current that reaches the heater? My thought is that maybe, just maybe, we could limit its performance enough to prevent the AFR sensor from functioning correctly, thus putting the car in open loop.
I'm going to just tune the car instead of resetting the battery. If it swaps back to closed loop at some point - no biggie.
EDIT: As soon as I plugged my FIC back in and started the car, the issue resolved itself. I'm still clueless as to what I just witnessed, but I would love to find out. There must have been some criteria the engine failed to meet to throw itself into closed loop. The catch would seem that whatever it is doesn't cause a code though...
Oh and also - I was reading the service manual and noticed the AFR sensor heater operates between .9 and 10 Amps. A code is thrown if the current drops below .8A. Could it be possible to greatly limit the current that reaches the heater? My thought is that maybe, just maybe, we could limit its performance enough to prevent the AFR sensor from functioning correctly, thus putting the car in open loop.
I'm assuming no one understands what the hell I've been talking about lol.
Anyways, there must be something wrong with my AFR sensor. Started the car up today, and it did the open loop thing. It started open, warmed up, went closed, then around 115F water temp it opened again. 😕
Pulled my FIC bypass plug, put it back in, problem solved. Drove to class and got P2238 when I was almost there. The car went open loop, I cleared the code, and back to closed. On the way home, no code but it just suddenly got stuck in open loop again. The whole thing is so strange, but I can't be bothered with crap like this.
I've pulled my AFR sensor plug and am going to tune the car in open loop. I should have done this awhile ago, instead of messing around with the FIC. This is tried and true, and a CEL that doesn't cause limp isn't the end of the world.
Anyways, there must be something wrong with my AFR sensor. Started the car up today, and it did the open loop thing. It started open, warmed up, went closed, then around 115F water temp it opened again. 😕
Pulled my FIC bypass plug, put it back in, problem solved. Drove to class and got P2238 when I was almost there. The car went open loop, I cleared the code, and back to closed. On the way home, no code but it just suddenly got stuck in open loop again. The whole thing is so strange, but I can't be bothered with crap like this.
I've pulled my AFR sensor plug and am going to tune the car in open loop. I should have done this awhile ago, instead of messing around with the FIC. This is tried and true, and a CEL that doesn't cause limp isn't the end of the world.
Sounds very similar to my problems. My car stayed in closed loop but my factory O2 sensor was going wacky. While driving it was OK but when hot at idle it was very slow to respond. Sometimes it would go so lean it would dye out. I think the location of the o2 had something to do with it. Mabe if it was located before the turbo it would be OK. I have removed the o2 sensor and tuned in open loop. Much better now. Still need some bigger squirters though.
WOW I should have tuned the car like this sooner. It's soooo easy. Not to mention it does in fact feel like it drives better.
Honestly, I think this is the way most people should consider using. Besides having a constant CEL, the only other very slight downfall is a SMALL loss in fuel economy. If you tune the car around 14.7 out of boost, and richer during boost, the loss will be minimal though.
Also - just got my cheapo manual boost controller today (Joe P, ball and spring type). Since I'm tuning I feel a little more comfortable using it, so I'll install it tomorrow. Should be interesting to see what happens with spooling once I get it set to the right psi. 👍
Will post up my tune once I'm thoroughly satisfied with it. Should be very helpful for all future Zage users, but only if you're tuning the car in open loop.
Honestly, I think this is the way most people should consider using. Besides having a constant CEL, the only other very slight downfall is a SMALL loss in fuel economy. If you tune the car around 14.7 out of boost, and richer during boost, the loss will be minimal though.
Also - just got my cheapo manual boost controller today (Joe P, ball and spring type). Since I'm tuning I feel a little more comfortable using it, so I'll install it tomorrow. Should be interesting to see what happens with spooling once I get it set to the right psi. 👍
Will post up my tune once I'm thoroughly satisfied with it. Should be very helpful for all future Zage users, but only if you're tuning the car in open loop.
^ Excellent! I got five more Zage kits in today. 👍
😲Originally Posted by cali yaris ↑^ Excellent! I got five more Zage kits in today. 👍
So anyone remember how I said the Zage BOV has a sweet, unique sound? No, I was wrong. I have BOV flutter lol... But it sounds soo cool 🎉
Currently looking into it... Having flutter means the BOV is set too soft I think?
Currently looking into it... Having flutter means the BOV is set too soft I think?
^ so it isn't closing tight enough, right?
I read somewhere that its the air recirculating and pushing the turbo blades backwards. someone was saying that it isn't THAT bad on a small amount of boost?
I think peterpoop is right. The flutter sound is compressor surge [air going back through turbo blades]. IE: the bov may be a little tight. Mine was set to loose and my engine kept dying out because it was leaking out to much metered air and I went way rich. I tightened up the spring and now I get some flutter before I get the air rush sound when it opens. But now it almost never dyes out. I dont think a little flutter will hurt as long as when your on the gas hard you hear it open when you let off. Its hard to imagine the whole automatic trans. situation.
I've been playing around with my manual boost controller the last few days and haven't seen any noticeable improvement in spooling unfortunately, but I'll keep at it.
Was wondering about this though.... If my PCV hose has a kink in it, that would cause blow-by and oil in the intake, right? I'm thinking that's the reason I found oil in the intercooler. Looks like it could also be related to my P0101 code.
Was wondering about this though.... If my PCV hose has a kink in it, that would cause blow-by and oil in the intake, right? I'm thinking that's the reason I found oil in the intercooler. Looks like it could also be related to my P0101 code.
The more I think about it, the more I think you're right...
PCV being clogged can't get oil in the charge piping, especially when there's none in the MAF piping.
So this means one of two things. Either the oil level issue, or my seals are blown. I don't want to accept the latter, but I don't think that's the case anyways because I'd have lost more oil (?).
I'm going to tap my block sometime this week. We'll see what happens.
PCV being clogged can't get oil in the charge piping, especially when there's none in the MAF piping.
So this means one of two things. Either the oil level issue, or my seals are blown. I don't want to accept the latter, but I don't think that's the case anyways because I'd have lost more oil (?).
I'm going to tap my block sometime this week. We'll see what happens.
Thanks for the info, I was under the impression that there WAS some sort of gasket material in use for the seals.Originally Posted by cdydjded ↑BTW what part on our car are you calling a PCV? Also turbo there is a big misconception on what a turbo seal is. Just to let you know a turbo has no seals in the sence that there are made from gasket material or rubber o ring. Everything on a turbo is made from metal like brass or steel. If you in & out of oil supply has to much psi or too little flow the only place oil can go is out the turbine side ot compressor side. Technicaly a turbo has bushings that kit oil in the oil chamber.
As for PCV hose, I'm talking about the hose that connects to the MAF piping. It looked like I was running with it kinked for some time.
Picture not included in this copy
Alright well here's my tune for anyone interested. I'm pretty satisfied with it at this point.
Specs:
-AEM FIC Fuel map
-Zage Turbo Kit
-AFR Sensor unplugged
-1ZZ Injectors (240-260cc; stock: 200cc)
-MBC set to about 8 psi (probably irrelevant)
-Automatic (should work just as well for manual)
I've set this tune up to get both the best of performance and fuel economy. At any point outside of boost, I've aimed for 14.7 (stoich) for emissions and fuel economy purposes. Here's how I have boost arranged...
1 psi - low 14s, high 13s
2 psi - Around 13.5
3 psi - low 13s, high 12s
4 psi - 12-12.5
5 psi+ - Around 11.5
I thought this was pretty reasonable considering after a couple of months driving around without a tune, stoich seemed to be fine up to 5 psi. Obviously the greater the air is compressed, the more heat is produced, so additional fuel (for cooling) should be added. I've definitely noticed a performance increase by running richer AFRs as well.
Hopefully this tune will be largely plug and play, but if not, I'd like to point out how I went about this. ANYONE can do this (with a wideband, of course).
-Hook laptop up to FIC to log the run (I never used the internal logger).
-Log the run. I honestly just did this during normal driving. You're going to want some spots where you're boosting, and simply cruising.
-Open the log up in excel and hide all data except RPMs, fuel trim, wideband, and engine load.
-Look for areas in the log where the breakpoints on the fuel map approximately match up. Then look at the fuel trim on excel and the map. Subtract points from the map at that location to lean the mixture, add points to richen the mixture. I never added/subtracted too much at once - you only want small changes until you reach your desired AFR.
***This is a weird glitch in the coding of the FIC I discovered (pimp my yaris also had this problem). Everywhere you see a .8, leave it alone. It's simply there to prevent the following. Apparently, when the FIC is fueling and it gets dropped to 0 (i.e. accelerating then letting off the throttle) it freaks the hell out. I noticed it was just dumping fuel at AFRs richer than 10. My engine was stuttering badly until I replaced all the zeroes with .8.
At this point, the only way I can make a Zage turbo kit install easier is by showing up and doing it myself lol.
DISCLAIMER: I'm not responsible for any problems that may arise from using my tune. It's tried and tested, but not stupid-proof.
Specs:
-AEM FIC Fuel map
-Zage Turbo Kit
-AFR Sensor unplugged
-1ZZ Injectors (240-260cc; stock: 200cc)
-MBC set to about 8 psi (probably irrelevant)
-Automatic (should work just as well for manual)
I've set this tune up to get both the best of performance and fuel economy. At any point outside of boost, I've aimed for 14.7 (stoich) for emissions and fuel economy purposes. Here's how I have boost arranged...
1 psi - low 14s, high 13s
2 psi - Around 13.5
3 psi - low 13s, high 12s
4 psi - 12-12.5
5 psi+ - Around 11.5
I thought this was pretty reasonable considering after a couple of months driving around without a tune, stoich seemed to be fine up to 5 psi. Obviously the greater the air is compressed, the more heat is produced, so additional fuel (for cooling) should be added. I've definitely noticed a performance increase by running richer AFRs as well.
Hopefully this tune will be largely plug and play, but if not, I'd like to point out how I went about this. ANYONE can do this (with a wideband, of course).
-Hook laptop up to FIC to log the run (I never used the internal logger).
-Log the run. I honestly just did this during normal driving. You're going to want some spots where you're boosting, and simply cruising.
-Open the log up in excel and hide all data except RPMs, fuel trim, wideband, and engine load.
-Look for areas in the log where the breakpoints on the fuel map approximately match up. Then look at the fuel trim on excel and the map. Subtract points from the map at that location to lean the mixture, add points to richen the mixture. I never added/subtracted too much at once - you only want small changes until you reach your desired AFR.
***This is a weird glitch in the coding of the FIC I discovered (pimp my yaris also had this problem). Everywhere you see a .8, leave it alone. It's simply there to prevent the following. Apparently, when the FIC is fueling and it gets dropped to 0 (i.e. accelerating then letting off the throttle) it freaks the hell out. I noticed it was just dumping fuel at AFRs richer than 10. My engine was stuttering badly until I replaced all the zeroes with .8.
At this point, the only way I can make a Zage turbo kit install easier is by showing up and doing it myself lol.
DISCLAIMER: I'm not responsible for any problems that may arise from using my tune. It's tried and tested, but not stupid-proof.
1 attachment not included in this copy
No problem, pimp my yaris more or less pointed it out when we were chatting. Now everyone knows - it is a pretty weird problem though.
As some of you may know, I've been having problems with my tune suddenly becoming substantially richer with colder weather. I now know for a fact why this is happening, and figured this would be great to know for anyone who intends to do their own tuning.
In a nutshell, the problem is New Jersey's crappy seasons. I was reading into spark plugs and found an interesting point on NGK's site that confirmed my suspicions. In general, fuel injected engines will richen the mixture during colder weather to compensate for denser air. Ok, no big surprise. However, the way my tune is set up is a problem now. The FIC doesn't allow zero values or negative values in the fuel map without causing huge engine hesitation. So leaning out the mixture is out of the question.
I was driving today and realized the ECU is doing what it's programmed to do. Then it hit me... I HAVE 1ZZ INJECTORS INSTALLED. Without an AFR sensor to correct the mixture, it's adding fuel based on quantity of air and calculating the duty cycle as if 1NZ injectors were in.
I'm going to swap them out tomorrow. However, this has me slightly concerned as to whether or not the 1NZs will max out by 8 psi of boost. I guess I have no choice but to try 🤷
In a nutshell, the problem is New Jersey's crappy seasons. I was reading into spark plugs and found an interesting point on NGK's site that confirmed my suspicions. In general, fuel injected engines will richen the mixture during colder weather to compensate for denser air. Ok, no big surprise. However, the way my tune is set up is a problem now. The FIC doesn't allow zero values or negative values in the fuel map without causing huge engine hesitation. So leaning out the mixture is out of the question.
I was driving today and realized the ECU is doing what it's programmed to do. Then it hit me... I HAVE 1ZZ INJECTORS INSTALLED. Without an AFR sensor to correct the mixture, it's adding fuel based on quantity of air and calculating the duty cycle as if 1NZ injectors were in.
I'm going to swap them out tomorrow. However, this has me slightly concerned as to whether or not the 1NZs will max out by 8 psi of boost. I guess I have no choice but to try 🤷
^ That was the problem.
I'd also like to debunk the whole 1NZ injector maxing out thing once and for all. 1NZ injectors should be good for up to about 10 psi of boost. However, it's not that simple if you want to run a safe AFR. For example, the first point the duty cycle maxes is at 7 psi @ 5000 RPMs. This assumes a target AFR of 11.5. It's still possible to maintain 11.5 AFR at about 10 psi @ 3500 RPMs as well. You could probably get away running a little leaner under full boost (low 12s). It all really depends on how hard you drive the car.
This means larger injectors aren't needed for low boost applications (8-9 psi) unless you're redlining the car all the time. Even 10 psi will be safe. If you're tuning open loop, I definitely recommend NOT switching the injectors. At below freezing ambient air temps, the ECU was richening up my cruising mixture to as much as high 12s. In other words - I was wasting a ton of gas 😳
It's so much fun being the one who has to make the mistakes first 🙄
I'd also like to debunk the whole 1NZ injector maxing out thing once and for all. 1NZ injectors should be good for up to about 10 psi of boost. However, it's not that simple if you want to run a safe AFR. For example, the first point the duty cycle maxes is at 7 psi @ 5000 RPMs. This assumes a target AFR of 11.5. It's still possible to maintain 11.5 AFR at about 10 psi @ 3500 RPMs as well. You could probably get away running a little leaner under full boost (low 12s). It all really depends on how hard you drive the car.
This means larger injectors aren't needed for low boost applications (8-9 psi) unless you're redlining the car all the time. Even 10 psi will be safe. If you're tuning open loop, I definitely recommend NOT switching the injectors. At below freezing ambient air temps, the ECU was richening up my cruising mixture to as much as high 12s. In other words - I was wasting a ton of gas 😳
It's so much fun being the one who has to make the mistakes first 🙄
^ sorry but I find this confusing. You said:
For example, the first point the duty cycle maxes is at 7 psi @ 5000 RPMs.which is nowhere near redline, and nowhere near 10psi. then you said:
This means larger injectors aren't needed for low boost applications (8-9 psi) unless you're redlining the car all the time.can you clarify please?
Sorry I'm just so used to looking at the FIC fuel maps when I'm sure many others haven't even seen what they look like. I'll break this down as much as possible and assume nothing.
Firstly, it's widely accepted that 11.5 is a good AFR for boost conditions. In order to maintain that ratio, the duty cycle (time the injectors are held ON), must be increased as engine load and RPMs increase. Simple concept - the harder the engine works, the more air is needed, and thus the more fuel is needed. Varying load/ RPM combos need different values. For example, 2 psi of boost @ 5000 RPMs is NOT going to need the same duty cycle for 2 psi of boost @ 1200 RPMs.
That's why the duty cycle maxes at different RPMs for each pound of boost (starting at 7). In this case you can say the fuel needed to maintain 11.5 at 7 psi @ 5000 RPMs is close to the fuel needed at 10 psi @ 3500 RPMs - the maximum duty cycle (100%).
Here's a couple of examples of duty cycle maxing to show the linear trend it follows (approximately):
6 psi @ about redline
7 psi @ 5000 RPMs
8 psi @ 4400 RPMs
9 psi @ 4000 RPMs
10 psi @ 3500 RPMs
11 psi @ 3200 RPMs
The last three are theoretical, but should be pretty accurate.
Hopefully that'll clear it up a bit. I'm struggling to explain this right now 🤷
Firstly, it's widely accepted that 11.5 is a good AFR for boost conditions. In order to maintain that ratio, the duty cycle (time the injectors are held ON), must be increased as engine load and RPMs increase. Simple concept - the harder the engine works, the more air is needed, and thus the more fuel is needed. Varying load/ RPM combos need different values. For example, 2 psi of boost @ 5000 RPMs is NOT going to need the same duty cycle for 2 psi of boost @ 1200 RPMs.
That's why the duty cycle maxes at different RPMs for each pound of boost (starting at 7). In this case you can say the fuel needed to maintain 11.5 at 7 psi @ 5000 RPMs is close to the fuel needed at 10 psi @ 3500 RPMs - the maximum duty cycle (100%).
Here's a couple of examples of duty cycle maxing to show the linear trend it follows (approximately):
6 psi @ about redline
7 psi @ 5000 RPMs
8 psi @ 4400 RPMs
9 psi @ 4000 RPMs
10 psi @ 3500 RPMs
11 psi @ 3200 RPMs
The last three are theoretical, but should be pretty accurate.
Hopefully that'll clear it up a bit. I'm struggling to explain this right now 🤷
Me too ^
Hey all
Been awhile since I updated. As some of you may be aware I've had an ongoing "boost leak" problem pretty much since I've finished the install. This week I finally got around to running some boost leak tests and found a whopping 10 leaks. Some of them were pretty significant. Needless to say the car idles substantially better now. Unfortunately... My leak problem remains.
I'm baffled and really need some help. What I'd like to think this means is that the exhaust is somehow the culprit... Whenever I get on the throttle I hear a ton of air escaping. I've combed the damn thing over so many times and found no noticeable air leaks that would hurt spooling. I'm beginning to wonder if my 2.25" crush bent catback is just not providing enough breathing and air is being forced out of whatever little crack it can find...
Anyone have any ideas, things to try, how to accurately test for exhaust leaks etc? I'm tired of being stuck at 5 psi.
Been awhile since I updated. As some of you may be aware I've had an ongoing "boost leak" problem pretty much since I've finished the install. This week I finally got around to running some boost leak tests and found a whopping 10 leaks. Some of them were pretty significant. Needless to say the car idles substantially better now. Unfortunately... My leak problem remains.
I'm baffled and really need some help. What I'd like to think this means is that the exhaust is somehow the culprit... Whenever I get on the throttle I hear a ton of air escaping. I've combed the damn thing over so many times and found no noticeable air leaks that would hurt spooling. I'm beginning to wonder if my 2.25" crush bent catback is just not providing enough breathing and air is being forced out of whatever little crack it can find...
Anyone have any ideas, things to try, how to accurately test for exhaust leaks etc? I'm tired of being stuck at 5 psi.
Holy thread revival LOL
easiest way that I know of to find exhaust leaks is to get the car up on stands, start it and let it idle and have someone with a rag block off the tailpipe. You'll hear the puffing sound out of any leak in your exhaust.
easiest way that I know of to find exhaust leaks is to get the car up on stands, start it and let it idle and have someone with a rag block off the tailpipe. You'll hear the puffing sound out of any leak in your exhaust.
2.25" shouldn't be the source of the problem, unless it's blocked somewhere inside.
My current running theory is at least one of the cats is clogged from the oil burning caused by the whole zage oil pan fiasco...
Sorry for the necromancer antics. Personally, I like this thread 👍
Sorry for the necromancer antics. Personally, I like this thread 👍
I like it too. 🙂 I just had to replace (remove, actually) a cat from a '79 Spitfire. It was 90% blocked with oil and gunk. Totall fixed the problem.
^ Had the cats removed and that was what I expected to see. They looked brand new still. However, removing them freed up a noticeable amount of power all across the band (especially at higher revs).
But I solved the problem anyway lol. Apparently that air escaping was just the wastegate cracking lmao. Inexperience... 😆
The actual problem was the truboost. I must have wired it wrong because as soon as I plumbed a manual boost controller in the line I was spiking up to 11 psi. Adjusted it and now running 8-9 psi. Feels great man 👍
But I solved the problem anyway lol. Apparently that air escaping was just the wastegate cracking lmao. Inexperience... 😆
The actual problem was the truboost. I must have wired it wrong because as soon as I plumbed a manual boost controller in the line I was spiking up to 11 psi. Adjusted it and now running 8-9 psi. Feels great man 👍
EXCELLENT. 👏
So uh... I've got problems. 😢
Seemingly out of nowhere last night, my engine started running like complete garbage. Here's the symptoms...
-Cold start, engine warms up fine until about 130C water temp.
-After that, AFR goes super lean, vacuum drops to 9 inHG, IGN goes negative, RPMs less than 500
-If I step on the gas, the AFR goes super rich
-During cruise, my AFRs fall into a more acceptable range
-I have no new codes. Just the usual P0031 from not having a front O2 sensor.
-FIC bypass makes no difference.
-Battery voltage is healthy with engine on and off
-Ran two different sets of plugs with varying gaps - nope.
All signs point to a vacuum leak, but I haven't been able to find one. I'll have an air compressor tomorrow for a more thorough check, but I'm not entirely convinced I'll find one...
Other thoughts:
-Bad gas (I've had a similar experience before, but not this severe)
-Stuck valve
Help guys 🙁
Seemingly out of nowhere last night, my engine started running like complete garbage. Here's the symptoms...
-Cold start, engine warms up fine until about 130C water temp.
-After that, AFR goes super lean, vacuum drops to 9 inHG, IGN goes negative, RPMs less than 500
-If I step on the gas, the AFR goes super rich
-During cruise, my AFRs fall into a more acceptable range
-I have no new codes. Just the usual P0031 from not having a front O2 sensor.
-FIC bypass makes no difference.
-Battery voltage is healthy with engine on and off
-Ran two different sets of plugs with varying gaps - nope.
All signs point to a vacuum leak, but I haven't been able to find one. I'll have an air compressor tomorrow for a more thorough check, but I'm not entirely convinced I'll find one...
Other thoughts:
-Bad gas (I've had a similar experience before, but not this severe)
-Stuck valve
Help guys 🙁
for one, at 130°C you're cooking the engine. Maybe you mean °F when around the cool light goes off?
You've tried resetting the ECU? also, do you have a way to add the front O2 sensor back in?
You've tried resetting the ECU? also, do you have a way to add the front O2 sensor back in?
for one, at 130°C you're cooking the engine. Maybe you mean °F when around the cool light goes off?
You've tried resetting the ECU? also, do you have a way to add the front O2 sensor back in?
You've tried resetting the ECU? also, do you have a way to add the front O2 sensor back in?
Yeah, 130F, typo... Otherwise my block would be on its way to becoming a puddle of aluminum.
ECU has been reset. Front O2 sensor I would need to pick up, but I need one for inspection anyway...
If a vacuum leak doesn't turn up, I'll grab an O2 sensor, return to closed loop, and go from there. Wish me luck 🤷
ECU has been reset. Front O2 sensor I would need to pick up, but I need one for inspection anyway...
If a vacuum leak doesn't turn up, I'll grab an O2 sensor, return to closed loop, and go from there. Wish me luck 🤷
So I can't find any vacuum leaks. I checked the injectors too. Look clean and all cycle fine.
But uh.. I did find my OEM O2 sensor floating around in the engine bay lmao.
The result is the same. The only difference is you can see the afrs being adjusted back to stoich, but they continue to go either super lean or rich (if I touch the gas). Also, no codes. I might attempt to drive a bit to complete the drive cycle but I'm not crazy about that.
Gonna do a compression test shortly. Let me know if you think there's any abnormal engine noises (this was taken while the afrs were somewhat maintaining stoich).
http://youtu.be/cgtU-mSDaBk
But uh.. I did find my OEM O2 sensor floating around in the engine bay lmao.
The result is the same. The only difference is you can see the afrs being adjusted back to stoich, but they continue to go either super lean or rich (if I touch the gas). Also, no codes. I might attempt to drive a bit to complete the drive cycle but I'm not crazy about that.
Gonna do a compression test shortly. Let me know if you think there's any abnormal engine noises (this was taken while the afrs were somewhat maintaining stoich).
http://youtu.be/cgtU-mSDaBk
OH!! did you check the MAF sensor? Weird things happen when they get dirty.
PS, clicked on the vid with my home theatre system on with the sub, sounds like I was standing there looking for myself LOL
PS, clicked on the vid with my home theatre system on with the sub, sounds like I was standing there looking for myself LOL
Yeah I was surprised at how awesome the sound was too 😁. Usually most phone videos sound like a gargled bunch of crap.
I checked the MAF. Pins and IAT sensor looks clean. Only other thing I can think of is voltage checks.
BTW, here's a video of the engine being bogged down (rich). Probably irrelevant, but eh.
http://youtu.be/zQSgTpNFrpU
I checked the MAF. Pins and IAT sensor looks clean. Only other thing I can think of is voltage checks.
BTW, here's a video of the engine being bogged down (rich). Probably irrelevant, but eh.
http://youtu.be/zQSgTpNFrpU
Ok, back to the O2 sensor, was it bolted in place just not hooked up, or hook up, just not in the exhaust?
I took it out once I found out how bad leaving it downstream, unplugged, was. It appears to be working fine and the car is maintaining closed loop without a problem (but not stoich). I guess it's still possible that its faulty, but that still doesn't explain why I could run open loop for so long without problems.
maybe it got damaged? and is giving bad out of range readings, but not enough for a code.
It's definitely possible, but still wouldn't explain the open loop situation. I was thinking the same with the back O2 sensor, but that's purely for emissions right?
It looks like I need to drive enough to complete a drive cycle....
EDIT: Compression - 195, 195, 205, 205
Side note: If stock is 213 and that's after 2 and a half years of boost... Well, 'nuff said.
It looks like I need to drive enough to complete a drive cycle....
EDIT: Compression - 195, 195, 205, 205
Side note: If stock is 213 and that's after 2 and a half years of boost... Well, 'nuff said.
Ok, I'm completely out of ideas...
-Replaced the MAF - no
-Checked the throttle plate - fine
-Monitored O2 sensor voltage - within range
-PULLED the rear O2 - no change (apparently it doesn't affect af/r at all, even though the service manual makes it out to be a pretty big deal)
-No exhaust leaks
I'm noticing more so that during closed loop I can 'somewhat' maintain stoich, but as soon as I touch the gas everything goes to hell. Rich, engine bogs, doesn't recover at all.
Also, I did manage to throw a system too lean code, but... duh. Not sure how credible that is because I was screwing with MAF skews in the FIC...
HELP ME lol. I've never been so stumped by anything engine related 🙄
-Replaced the MAF - no
-Checked the throttle plate - fine
-Monitored O2 sensor voltage - within range
-PULLED the rear O2 - no change (apparently it doesn't affect af/r at all, even though the service manual makes it out to be a pretty big deal)
-No exhaust leaks
I'm noticing more so that during closed loop I can 'somewhat' maintain stoich, but as soon as I touch the gas everything goes to hell. Rich, engine bogs, doesn't recover at all.
Also, I did manage to throw a system too lean code, but... duh. Not sure how credible that is because I was screwing with MAF skews in the FIC...
HELP ME lol. I've never been so stumped by anything engine related 🙄
Are you still running the stock fuel system?
Yes. The pump and regulator are the only things I haven't checked, mainly because I can't find a thorough way to do so.
What's the intake air temp reading?
Completely fine. So is the coolant temp.
Is the regulator the thing on the fuel rail? I remember reading somewhere it was part of the pump assembly...
Is the regulator the thing on the fuel rail? I remember reading somewhere it was part of the pump assembly...
Yeah part of the pump. Almost seems ECU related. The way it runs fun in closed loop while cold then like crap when in open.
I'm definitely a little worried about that, but everything else seems to be running fine. I'd expect to see more adverse side effects if the ECU was crapping out (esp. from what we've seen with yaris2010RS). It's almost like the only problem is fuel delivery is being adjusted too slowly. For example, when I hit the gas during idle the mixture goes lean for a few seconds, then overly rich. If I go light on the throttle it will sometimes recover and then go back to being lean before kind of settling around stoich.
Any ideas on how to test fuel pressure? The pump is probably okay if it's actually delivering too much fuel, but maybe the regulator is getting stuck...?
Any ideas on how to test fuel pressure? The pump is probably okay if it's actually delivering too much fuel, but maybe the regulator is getting stuck...?
Yeah you just need to get a pressure gauge to go under the hood where the fuel line connects up to the rail. There's a quick release fitting there. I think you need a special tool to get it apart. That is another good possibility. Maybe dirt got through the in tank filter and is making the pressure reg slow.