Yarisworld Archive

I NEED Boost... Opinions puh-lease

517 posts · 111,381 views · page 10 of 11

Replies continued

yaris2010RSAngus, Ontario · Dec 18, 2012#451
Originally Posted by Focus_Sh1ft ↑
No, all four plugs are getting fouled. Even though the afrs are running from super rich to super lean, they're generally on the rich side (especially in open loop). There's no way all four injectors are suddenly sticking. I'd also expect to see a slightly higher compression in one cylinder from carbon buildup.

Also, to be clear, when I run open loop my afr sensor is NOT plugged into the harness and NOT downstream. Therefore no values are being read.

Even though the ecm is ruled out, I still can't get over the nagging feeling that this is somehow electrical (I checked all fuses BTW)...
$130 is alot for a sensor i have a spare one kicking around in my garage LOL, Should have asked man....

Im sorry to try to stick on one thing, but it sounds ALOT like what my car was doing when the ECM was gone......

Have you done a compression test? good place to loose vac is in the cylinders is a leak test on the intake passed. if this was a vac leak on the hose or cracked intake mani i believe you would get a very unpridctible idle (up and down or really high) with the car running spreay some brake cleaner or WD40 or something flamable and controlable to see if your RPMS go up when you spray suspected spots.

Another shot in the dark (im good at these but that doesnt make them useful) have you checked the condition of your turbo? possibly if its in dire need of a rebuild it could be holding up enough back pressure to screw with things. check from intake and exhaust side. also while your at it check the rest of your exhaust system or some sort of blockage (if you have a cat, check it!)

These are all the things i checked on my car. they went the cause but i had convinced myself they could be
Focus_Sh1ftThread starterNew Jersey · Dec 19, 2012#452
Spent the last few hours combing over the car with my mechanic... and nothing.

-Fuel pressure was fine
-Smoke test turned up nothing
-All sensors are within range via OBDII

We were finally able to get a P0171 code thrown, but that's it. The trims were everywhere - off gas they were trimming fuel like crazy, while on gas it was adding way too much fuel. In other words, they've never seen anything like this before.

So at this point, the only thing that can't be ruled out 100% is the ECM. However, the replacement ECM didn't do anything. The one and only remaining cause is a problem with the harness. Here's what I'm thinking

-Sweet talk someone at Toyota into doing some monitoring with the techstream tool. If the ECM is compromised or a short/open in the harness, it should show up.
-If not, attempt to continuity check EVERY SINGLE WIRE on the ECM (dear lord). I don't even know if the information for this is actually readily available.
-If not, attempt to source a replacement harness

Otherwise... We're talking complete engine replacement. I knew the day would come, but I thought it would be because I BLEW the engine, not some electrical BS.
CTScottUSA, CT · Dec 19, 2012#453
Originally Posted by Focus_Sh1ft ↑
Spent the last few hours combing over the car with my mechanic... and nothing.

-Fuel pressure was fine
-Smoke test turned up nothing
-All sensors are within range via OBDII

We were finally able to get a P0171 code thrown, but that's it. The trims were everywhere - off gas they were trimming fuel like crazy, while on gas it was adding way too much fuel. In other words, they've never seen anything like this before.

So at this point, the only thing that can't be ruled out 100% is the ECM. However, the replacement ECM didn't do anything. The one and only remaining cause is a problem with the harness. Here's what I'm thinking

-Sweet talk someone at Toyota into doing some monitoring with the techstream tool. If the ECM is compromised or a short/open in the harness, it should show up.
-If not, attempt to continuity check EVERY SINGLE WIRE on the ECM (dear lord). I don't even know if the information for this is actually readily available.
-If not, attempt to source a replacement harness

Otherwise... We're talking complete engine replacement. I knew the day would come, but I thought it would be because I BLEW the engine, not some electrical BS.

I have a Techstream. Take a run up to CT.
Focus_Sh1ftThread starterNew Jersey · Dec 19, 2012#454
I wish I could Scott, but with how the car is running it's not feasible. Thanks for the offer tough.

I was thinking though... If I shipped you one of these ECMs I have, could you possibly confirm if it's in a working state? Obviously doing the check through my car and thus the harness would be best but... Yeah. Still, if I could find out if the ECM is good or bad, that's still a pretty good datapoint.

One other thing regarding checking the harness... In the service manual's ECM pinout, would I be right in thinking the two pins listed under 'Symbols (Terminal No.)' should always have continuity?
CTScottUSA, CT · Dec 19, 2012#455
Originally Posted by Focus_Sh1ft ↑
I wish I could Scott, but with how the car is running it's not feasible. Thanks for the offer tough.

I was thinking though... If I shipped you one of these ECMs I have, could you possibly confirm if it's in a working state? Obviously doing the check through my car and thus the harness would be best but... Yeah. Still, if I could find out if the ECM is good or bad, that's still a pretty good datapoint.

One other thing regarding checking the harness... In the service manual's ECM pinout, would I be right in thinking the two pins listed under 'Symbols (Terminal No.)' should always have continuity?
I can definitely check out the ECM for you. I can also give you a list of specific harness points to check (the ones most likely related to the behavior).
Focus_Sh1ftThread starterNew Jersey · Dec 19, 2012#456
Originally Posted by CTScott ↑
I can definitely check out the ECM for you. I can also give you a list of specific harness points to check (the ones most likely related to the behavior).
I would definitely appreciate the harness points list. I'll get back to you on the ECM though. I need to see how the dealership responds to my request first. Considering we've bought three cars from them, I hope reasonably...
CTScottUSA, CT · Dec 21, 2012#457
Originally Posted by Focus_Sh1ft ↑
I would definitely appreciate the harness points list. I'll get back to you on the ECM though. I need to see how the dealership responds to my request first. Considering we've bought three cars from them, I hope reasonably...
Here it is:

Yaris ECM - Connections.pdf

1 attachment not included in this copy

Focus_Sh1ftThread starterNew Jersey · Dec 22, 2012#458
Wow, that is comprehensive. Must have taken awhile to put together too. Thanks!
CTScottUSA, CT · Dec 22, 2012#459
Originally Posted by Focus_Sh1ft ↑
Wow, that is comprehensive. Must have taken awhile to put together too. Thanks!
Fortunately I had most of it together from some past projects. Start with checking out the wires related to the injectors, coils, cam, crank, and MAF. If those all check out, then the next stop would be the AFR and O2 sensors.
Focus_Sh1ftThread starterNew Jersey · Jan 9, 2013#460
Been away for the last two weeks, but got back into troubleshooting yesterday. It looks like I've [unfortunately] found the problem...

Short story: Blew the head gasket

Long story: Finally decided to bite the bullet and get Toyota involved. I was lucky enough to get a really cool tech who was interested in the car. First thing we did was hook up the techstream tool. Get this - there were five codes that were being thrown EVEN THOUGH THE CHECK ENGINE LIGHT WAS OFF. Only his Mongoose cable was able to retrieve them. That is the biggest load of bull. Anyway, had P0300, 0301, 0302, 0303, and 0172. Since the plugs are ruled out, he said it's possible (especially with a hotter plug) that the coils burnt out. It seems unlikely all four would go, but apparently it's happened before.

So after running the engine a bit, we removed all four plugs. Out of cylinder one (and only one) you could hear air escaping/vacuum. That was the first nail in the coffin. After that, we topped off the coolant and ran a coolant reservoir with the engine on. Sure enough, there were air bubbles and small pieces of aluminum...

I still don't fully understand how a head gasket leak would cause issues such as misfires, but the guy working with me was very knowledgeable. My coolant temperatures were never excessively hot, and there isn't any coolant leaking out of the head either.

So, that's it. There's a lot I need to figure out, but I refuse to return the car to stock.
Bluevitz-rsOshawa, Ontario, Canada · Jan 9, 2013#461
through in a new head gasket and maybe turn the boost down a bit. Or try and find a stronger one? I guess it depends on where the leak is when you get it apart. You'll probably find a tiny slit of black on the deck where the leak was. I've experienced this exact head gasket problem on a B18 LS Vtec on my friends old race car. Car kept overheating though, no other issues.
cali yarisCanoga Park, CA · Jan 9, 2013#462
Get that tC out and park the Yaris? 😁
Focus_Sh1ftThread starterNew Jersey · Jan 9, 2013#463
Originally Posted by cali yaris ↑
Get that tC out and park the Yaris? 😁
I wish it was that simple. Of course this had to happen mid winter... 🙄

I plan on upgrading the head gasket if there is a better one available. I'll probably begin tearing down the engine tomorrow, but going to do another compression test first (did the other one wrong apparently).

Can anyone chime in on the best way to deal with the timing chain?
yaris2010RSAngus, Ontario · Jan 10, 2013#464
PULL! lol
What do you mean "Deal" with it?
Focus_Sh1ftThread starterNew Jersey · Jan 10, 2013#465
Pretty good progress today. I'm almost there, but am kind of stuck on the camshafts / timing chain.

Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

So yeah... those camshafts. I've looked at the service manual and not only does it not make sense, but I can't get the plug out of the "service hole." Further, the flange nut on the number two camshaft sprocket isn't budging. My wrench is actually stripping it. It looks like I may be able to just remove the retainers and wiggle the camshaft out with the gear still on, but I dunno. Can anyone give me some pointers?
Bluevitz-rsOshawa, Ontario, Canada · Jan 10, 2013#466
You'll have to take the front of the motor apart. Probably need to release the auto tensioner and lock it back then pull the chain off the crank and then off the cams.
yaris2010RSAngus, Ontario · Jan 11, 2013#467
man..... after work ill try to take some pics for you of my torn down engine to try and help explain....

you'll have to remove the timing cover. once its off, remove the tensioner (by removing the preload then unbolting it). Once the tensioner is removed you can slip out all the chain guides and there should be enough play to pull the chain off the crank sprocket.

Once the chain is off the crank sprocet you should be able to pull the chain off the cam sprockets without removing the sprockets from the cams

EDIT: LOL, almost the exact same thing bluevitz-rs said....
Focus_Sh1ftThread starterNew Jersey · Jan 11, 2013#468
Thanks guys

...I was really trying to avoid taking the chain cover off 😢
Focus_Sh1ftThread starterNew Jersey · Jan 13, 2013#469
Now I really wish I hadn't taken the chain cover off... 😢

Picture not included in this copy

I can get another one pretty cheap thankfully, but was wondering if I could get away with just using sealant between the two pieces. Is the oil in the timing chain case pressurized? It looks like it's just thrown on the crank lubricating the chain as the engine turns.

Otherwise, I'm stuck on the head bolts. I thought it was a 12 pt socket I needed but was the exact opposite
pimp my yarischicago · Jan 14, 2013#470
I have the tool if U need it I can send it to U as long as U return it. Send me a PM with your address. I am surprised you blew the head gasket. The Yaris use a metal haed gasket and they are pretty strong. How much boost are U pushing? Did you retard the timing with the FIC timing map?
Picture not included in this copy
Focus_Sh1ftThread starterNew Jersey · Jan 14, 2013#471
Thanks for the offer pimp, but I already ordered one.

I was only pushing about 9 lbs with the timing untouched, but I don't think that was the issue. When I had the car at the mechanic, we noticed one of the clamps I had on the throttle body coolant hose had actually broken and was dripping coolant. It was a very slow leak, but overtime probably caused overheating... I never noticed excessive coolant temps though.
Bluevitz-rsOshawa, Ontario, Canada · Jan 14, 2013#472
Could've had an air pocket trapped in that spot an never know it.
pimp my yarischicago · Jan 14, 2013#473
I was pushing 12psi with stock compression, but I did retard the timing at any boost level over 7psi with the Fic map. It will help avoid detonation. If your car would stumble or miss on hard excel. it could be the knock sensor cutting spark because of detonation. When my car does it I know I need to retard timing a little further. Usually after turning up the boost when the engine is still a little cool. A negative sign - must be put in front of the value on the fic map. It can only retard timing. It can not advance. Just a sugestion.
A lot of detonation can cause a bad head gasket as well. My Conquest TSI (with cranked up boost) blew several head gaskets because I had no timing control.
Also that front cover and timing chain really suck with the engine in the car. Very tight fit. The exhaust cam sprocket has three marks on it. Make sure U align on the right one. It caused me three days of headaches with my car almost starting, but it would not keep running. Best of luck
Focus_Sh1ftThread starterNew Jersey · Jan 14, 2013#474
I definitely wish I knew what the exact cause of this was, but I think I'll take your advice pimp and retard the timing a bit. Maybe the manner in which the gasket failed will tell us something (or if the head is warped).
yaris2010RSAngus, Ontario · Jan 15, 2013#475
where did u guys get the proper head bolt tool? i hammered a tripple square into it to get mine out.
ilikericesavannah, ga · Jan 15, 2013#476
i hammered a tripple square into it to get mine out
*shudders*

You can easily find those. 8mm 12pt bit. Just type it in google and you will get so many choices.
Focus_Sh1ftThread starterNew Jersey · Jan 15, 2013#477
Originally Posted by yaris2010RS ↑
where did u guys get the proper head bolt tool? i hammered a tripple square into it to get mine out.
You had to hammer it? I thought the tool is a triple square?

Here's the one I got
http://www.ebay.com/itm/400243378711
yaris2010RSAngus, Ontario · Jan 15, 2013#478
^negative, i purchased a tripple square and the angles were slightly off, i had to grind down the tool i purchased just to squeeze it in where the silly head bolts go and still had to hammer it into the bolt head, the bolts are garbage but the hardened bit was able to get all the bolts out.

Toyota used a double hex bit. which is almost impossible to find from local stores. Toyota does admit this tool was used on purpose and is only used on a few models. They do make a tool themselves and supply all toyota techs with one. This is the scoop i got from toyota atleast. They will not sell me a tool nor let me borrow one, they did offer me for the cost of 1 hour of labour, when im ready to put my engine together they will do it for me......
yaris2010RSAngus, Ontario · Jan 15, 2013#479
12-Point XZN (Triple-Square)
This is another variant of a 12-point head. But (as the name indicates) it is made of three squares (instead of two hexagons). The corners are therefor 90 degrees (instead of 120 degrees). This is clearly visible in the pictures where the corners are much sharper on "triple-square" than on "double-hex" heads.


12-Point (Double-Hex)
This is one common variant of a 12-point head. It is made of two hexagons. The corners are therefor 120 degrees. Common sizes are 6, 8, 10 and 12 mm.
yaris2010RSAngus, Ontario · Jan 15, 2013#480
Originally Posted by Bluevitz-rs ↑
Could've had an air pocket trapped in that spot an never know it.
wouldnt that have gotten pushed out after a small amount of engine use?
Focus_Sh1ftThread starterNew Jersey · Jan 16, 2013#481
What a load of crap about that tool. That's a pretty pathetic tactic to get more business.

Be it overheating or predetonation, I'll definitely be accounting for both of them.

Tool should be here tomorrow, so we'll know more then.
yaris2010RSAngus, Ontario · Jan 16, 2013#482
Just courious, did u end up getting compression readings?

reading more into your troubles and comparing them with mine we definatly had the same issue..... i keep meaning to check my HG for signs of leaks
Focus_Sh1ftThread starterNew Jersey · Jan 16, 2013#483
I did do the test again (throttle open, engine cold) and got 210 across all four. Assuming it is truly the head gasket, it should be interesting to see how it failed. I'm guessing coolant in the cylinder(s) based on what was found.
yaris2010RSAngus, Ontario · Jan 16, 2013#484
Thats odd...... if there is coolant getting in it would most likely be on the return (down) stroke so on the compression stroke you should see a loss of pressure.

What made you lean towards coolant in the cylidners?
Focus_Sh1ftThread starterNew Jersey · Jan 18, 2013#485
Ok, head is off. Look at the pictures first...

Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy
Picture not included in this copy

There's little bits of aluminum everywhere on the gasket. It's also covered in coolant.

I can't find any major cracks or anything wrong with the gasket. However, look at the cylinders. I don't know what they look like normally, but mine look like they could be warped. Each of the corners looks slightly burnt also.

Anything else look out of the ordinary? I still have to check for warpage on the head.
pimp my yarischicago · Jan 20, 2013#486
If coolant enters the cylinder the top of the piston will be washed clean and it is very noticable. Your pistons look equally dark with slight carbon deposits. Pretty normal. Did you disconnect the fuel pump or the injectors when you did the compression test? If the injectors are still squirting fuel during the compression test the fuel will create a excellent seal for the rings and give you false readings. The test should be done dry, and then retested with a little oil in each cyl. to compare the difference.
Focus_Sh1ftThread starterNew Jersey · Jan 21, 2013#487
Yep, no cylinder washing...

I removed the two efi fuses when I did the compression tests.

At this point, I'm just going to replace the head gasket, have the head decked, and throw it all back together. It's been almost two months and I still am no closer to solving this... VERY frustrating.
yaris2010RSAngus, Ontario · Jan 21, 2013#488
IMO put her back together and see if shes magically back to life
Focus_Sh1ftThread starterNew Jersey · Jan 22, 2013#489
Originally Posted by yaris2010RS ↑
IMO put her back together and see if shes magically back to life
At this point, that's basically where I'm at. I'm convinced magic is the only thing that will solve this problem lol...

Hopefully something turns up with the head. On the flip side, at least I'll have completely ruled out any type of mechanical failure.
cali yarisCanoga Park, CA · Jan 22, 2013#490
^ It's a small club of people who have been able to look at their piston tops. 😁
fnkngrvIn The Hotbox · Jan 22, 2013#491
Originally Posted by cali yaris ↑
^ It's a small club of people who have been able to look at their piston tops. 😁
Ain't that the truth!
yaris2010RSAngus, Ontario · Jan 22, 2013#492
Originally Posted by cali yaris ↑
^ It's a small club of people who have been able to look at their piston tops. 😁
Piston Top Club

We will see.....
Focus_Sh1ftThread starterNew Jersey · Jan 25, 2013#493
Got the head back today, no warpage.

Also, big thanks to Adrian (fnkngrv) for sending me an extra timing chain cover.

Should have everything back together early next week...
fnkngrvIn The Hotbox · Jan 25, 2013#494
Originally Posted by Focus_Sh1ft ↑
Got the head back today, no warpage.

Also, big thanks to Adrian (fnkngrv) for sending me an extra timing chain cover.

Should have everything back together early next week...
Picture not included in this copy

No problem man. You have been a great resource for information as I was doing my turbo install and tweaks along the way. Your knowledge helped me immensely along with Carlos, Garm, Scott, and Brian. 🤘
Blown_xaVirginia · Jan 28, 2013#495
I should get on here more, I miss a lot and I think I could have helped a while ago. I haven't read everything but kinda glanced at you issue. A stock 1nzfe will blow a rod and crack ringlands way before blowing a head gasket, as result of detonation.
As for your misfire isues, make sure you have plugs gapped to probably .030 in. If you have done that already..... your FIC is faulty or you are in need of a resistor on the crank signal wire on the FIC harness. This was a common issue with running the FIC on a Scion tC a couple years back. Even AEM's own p&p harness needed a resistor wired in, until they got enough phone calls about it.
Focus_Sh1ftThread starterNew Jersey · Jan 28, 2013#496
^ I wish you did chime in sooner, because it took me tearing into the engine to realize the head gasket wasn't the issue lol.

Made some progress today. However, it all came to a grinding halt when I stripped one of the head bolts...

I got it pretty tight before it happened, the others are only about 1/4 turn tighter and are the correct torque. I'm severely worried that will be enough to cause compression loss though...

Once I get the timing chain back on (and timing aligned), could I possibly run the starter and do a normal compression test? Really don't want to put everything back together just to find it was [even more of] a waste of time.
Focus_Sh1ftThread starterNew Jersey · Jan 29, 2013#497
Did a faux leak down test of sorts. Put 140 psi of compressed air in each cylinder at TDC, valves closed. I don't have the gauges to measure percentage, but all four lost air at a nearly consistent rate, so we're still good to go 👍
Focus_Sh1ftThread starterNew Jersey · Jan 31, 2013#498
Engine is back together and is running the exact same.

So, it's back to the drawing board... At least I didn't make things worse lol.
pimp my yarischicago · Jan 31, 2013#499
Originally Posted by Focus_Sh1ft ↑
Engine is back together and is running the exact same.

So, it's back to the drawing board... At least I didn't make things worse lol.
That blows, I think all of us that have fucked around with cars long enough know your pain. I know I been their 😢
CTScottUSA, CT · Jan 31, 2013#500
Originally Posted by Focus_Sh1ft ↑
Engine is back together and is running the exact same.

So, it's back to the drawing board... At least I didn't make things worse lol.
Did you ever get a chance to have someone connect up a techstream?