Yarisworld Archive

Can we do this? (aka The DIY Cruise Control Thread)

498 posts · 380,332 views · page 7 of 10

Replies continued

nickhjortOneida, NY · May 16, 2009#301
Pics for now... I will take more in an hour or so when I get it put in...it's raining like a mofo here now...

Picture lost · i236.photobucket.com
This is my switch I bought at radio shack. You get four in a pack for 3.59 I think.

Picture lost · i236.photobucket.com
Aluminum bracket, switch and bolt that replaces stock clutch switch.

Picture lost · i236.photobucket.com
My Frankenstein (It's ALIIIIIIVE!!!!...almost🙄)

Picture lost · i236.photobucket.com
Picture lost · i236.photobucket.com


Just make sure you have a SPST switch that is normally open...not closed. Also make sure it is long enough to touch the little black plate you see in the picture. I think mine is barely gunna work. If not I will probably epoxy something onto the end to make the button part longer. We'll see in a few.
nickhjortOneida, NY · May 16, 2009#302
Well the switch was just barely too small. So JB Weld time...

Picture lost · i236.photobucket.com
Picture lost · i236.photobucket.com

I used a cap from a can of liguid wrench :) Now it truly is a frankenstein haha. But it's all good. Nobody can even see it unless they stick their head under the dash. Anyway more pics to come soon when it's installed in the car.
nickhjortOneida, NY · May 16, 2009#303
Alright peeps, it's in. It works so far when hooked up to the meter. Tomorrow I'm gunna wire it in and test her out. Now all I'm waiting for is the led "module", courtesy of CTScott then I'll be all set 👍

Picture lost · i236.photobucket.com

Picture lost · i236.photobucket.com

Picture lost · i236.photobucket.com

Picture lost · i236.photobucket.com
CTScottUSA, CT · May 17, 2009#304
Nice job with the DIY switch. Hopefully this week I'll be able to ship you the module for driving the LED.
nickhjortOneida, NY · May 17, 2009#305
Thanks :)
zlh99aSaskatchewan · May 17, 2009#306
I just did this mod using nickhjort's method. Many thanks to nickhjort and ctscott! You guys rock!!!
PatrickJohnsonMurfreesboro, TN · May 18, 2009#307
Originally Posted by CTScott ↑
Nice job with the DIY switch. Hopefully this week I'll be able to ship you the module for driving the LED.
a quick diy on the PIC programming you used and the circuit would be great too!
mrbondThread starterIllinois · May 18, 2009#308
Well, I installed everything Sunday. Didn't work, which means I'll have to buy some spade connectors. Might just be the ground, but I'll keep trying.
CTScottUSA, CT · May 18, 2009#309
Originally Posted by PatrickJohnson ↑
a quick diy on the PIC programming you used and the circuit would be great too!
I finally got around to prototyping it last night. Tonight I'll try it out on my car, and if all is well, I'll post the info on it.
nickhjortOneida, NY · May 19, 2009#310
Awsome. I'm glad everyone is having such good results with this project, minus mrbond, but you'll get it. Check your grounds :)

I got my clutch switch up and running today. It works just perfectly, but it truly is a frankenstein :) I will take some pics of the final setup when I get some daylight. You may want to just spend the 18 bucks and get the stock switch. It will definatly look way nicer than my setup. But no one will ever see it anyway, so if it works then who cares right? plus I only spent 3.50 for the switch. I had everything else on hand.

I can't wait for the LED module CTScott :) After that, my install is complete and I can finally take all the tools out of my car HAHA! Also let me know the cost of parts for that module so I can add that into my total cost...even though it will be a gift 🙌
nickhjortOneida, NY · May 19, 2009#311
Total running tally for this mod so far:
$9.50 for two black switches, two packs of resistors, and the little LED mount thingies
$3.50 for pack of 4 switches for the clutch switch
$???? for the LED light module (soon to be completed by CTScott)

Also include the cost of wire, some spade connectors, soldering stuff, electrical tape, all of which I already had.
CTScottUSA, CT · May 19, 2009#312
Originally Posted by nickhjort ↑
Total running tally for this mod so far:
$9.50 for two black switches, two packs of resistors, and the little LED mount thingies
$3.50 for pack of 4 switches for the clutch switch
$???? for the LED light module (soon to be completed by CTScott)

Also include the cost of wire, some spade connectors, soldering stuff, electrical tape, all of which I already had.


I just road tested the LED driver module on my 09. Having the indicators on the combination meter was quite handy. It took a couple of rounds of the PIC firmware to get the switch debouncing correct. I am shipping it to you today. Below are a couple of pictures (the PCB and the packaged module). I will post the schematic when I have a chance. The module hardware is fairly simple; basically a Microchip PIC12HV615 microcontroller (with built-in shunt regulator), 9 resistors, and a NPN transistor. The PIC microcontroller monitors the switch input via one of its analog to digital inputs. This lets it sense the difference between the on/off switch and the other switches. The PIC "HV" series microcontrollers have a built-in regulator which allows them to operate off of an unregulated power supply, eliminating the need for a voltage regulator.

Picture lost · i372.photobucket.com




As you can see from the labels, there are three connections:

1. Switch Input - This input gets connected to the wires going from the ECM and ground to the switches (Red to CCS and Black to ground).

2. LED Output - This output drives the Cruise Control on/off LED. This supplies 12 VDC, so it is intended to drive a panel mount LED with a built-in resistor.

3. +12 VDC power input (IG switched) - This wire gets connected to an ignition switched 12 volt source. The easiest place to connect to is the pink wire on the ignition switch connector.



This module will work with the DIY switches or with an OEM cruise stalk. I am shipping nickhjort's for no charge in appreciation for him being the guinea pig for this mod. If anyone else is interested in a completed module, I would probably need to charge $25 shipped to cover the parts cost (with the silly little box being the most expensive component) and labor to assemble.
PatrickJohnsonMurfreesboro, TN · May 19, 2009#313
I'd love to see a schematic. I would be willing even to have some PCBs etched for people as drop-ins. Does this just drive the On/OFF LED? What about the SET light?

EDIT: I see you mentioned it can sense the difference between the switches, so I assume this drives both LED's. Again though, if you post the schematic I can etch actual circuit boards (instead of perfboard) for you or anyone else if there is interest.
CTScottUSA, CT · May 19, 2009#314
Originally Posted by PatrickJohnson ↑
I'd love to see a schematic. I would be willing even to have some PCBs etched for people as drop-ins. Does this just drive the On/OFF LED? What about the SET light?

EDIT: I see you mentioned it can sense the difference between the switches, so I assume this drives both LED's. Again though, if you post the schematic I can etch actual circuit boards (instead of perfboard) for you or anyone else if there is interest.
It just drives the power LED. Because the switches are all paralleled together, the ADC is required to differentiate the on/off switch from the other three.

The problem with driving a SET LED, based on just the switch, is that there are too many conditions where you could press the switch, but not really be "set". Tonight I should have a chance to drop the schematic into ORCAD. If there was enough interest in the modules I figured I would do a run of boards.
PatrickJohnsonMurfreesboro, TN · May 19, 2009#315
Originally Posted by CTScott ↑
It just drives the power LED. Because the switches are all paralleled together, the ADC is required to differentiate the on/off switch from the other three.

The problem with driving a SET LED, based on just the switch, is that there are too many conditions where you could press the switch, but not really be "set". Tonight I should have a chance to drop the schematic into ORCAD. If there was enough interest in the modules I figured I would do a run of boards.
I see. pretty cool either way. I was thinking of just doing a cmos flip flop switch to run the LED. I figured I could use the connection made by the on/off to touch a flip flop circuit or a relay and reset it's state, turning on the LED. of course, that might be using a sledgehammer to drive a thumb tack :)
CTScottUSA, CT · May 19, 2009#316
Originally Posted by PatrickJohnson ↑
I see. pretty cool either way. I was thinking of just doing a cmos flip flop switch to run the LED. I figured I could use the connection made by the on/off to touch a flip flop circuit or a relay and reset it's state, turning on the LED. of course, that might be using a sledgehammer to drive a thumb tack :)

I started off thinking I would use a flip flop, but you can't drive anything unless you change to a switch with a second set of contacts and you also have to maintain a high impedance to not confuse the ECM. The microcontroller is definitely overkill, but they are under $2.
Sir A.Y. AtoyotSurrey, BC Canada · May 19, 2009#317
For controlling an indicator light- has anyone considered a DPST switch for on-off? Wouldn't work for the stock cruise switch, of course, but it should be OK for the improvised setups. Too simple?
CTScottUSA, CT · May 19, 2009#318
Originally Posted by Sir A.Y. Atoyot ↑
For controlling an indicator light- has anyone considered a DPST switch for on-off? Wouldn't work for the stock cruise switch, of course, but it should be OK for the improvised setups. Too simple?
With a DPDT switch you'd still need a circuit to toggle the LED on and off. The circuit becomes simpler (a flip flop using two transistors or one IC), but is still required, as the switch is a momentary input, rather than a toggled one.
Sir A.Y. AtoyotSurrey, BC Canada · May 19, 2009#319
Originally Posted by CTScott ↑
With a DPDT switch you'd still need a circuit to toggle the LED on and off. The circuit becomes simpler (a flip flop using two transistors or one IC), but is still required, as the switch is a momentary input, rather than a toggled one.
I get it now.

If someone can come up with a tidy module to make this work, it could be a minor cottage industry. It should work with the OEM switch installations, as well as the improvised ones.
CTScottUSA, CT · May 19, 2009#320
Originally Posted by PatrickJohnson ↑
I'd love to see a schematic. I would be willing even to have some PCBs etched for people as drop-ins. Does this just drive the On/OFF LED? What about the SET light?

EDIT: I see you mentioned it can sense the difference between the switches, so I assume this drives both LED's. Again though, if you post the schematic I can etch actual circuit boards (instead of perfboard) for you or anyone else if there is interest.
Here's the schematic:

mg_xpowerNetherlands · May 20, 2009#321
Nice work. Please consider the fact a car power supply is really "dirty". You'll have to take bursts and surges into account. I'd add a nice big elco to VDD (at least 100uF 35V) and a 100nF 50V X5R/X7R ceramic capacitor close to the controller.

Are you measuring battery voltage at p6 ? -> Add 100nF over R7.
regalPA · Jun 3, 2009#322
If you have an 09 LB I'de say the ebay stalk with a sparks oem clutch switch is the way to go, anyone tried it/.
nickhjortOneida, NY · Jun 5, 2009#323
Hold on just a couple more days and I'll have that module installed. I just haven't had time to rip the dash again. I also have to rethink my clutch switch, the switch broke. That's what I get for going cheap :) Anyway, I'll prolly just buy the oem one. I'll put picks up when I'm done with all of this...
regalPA · Jun 5, 2009#324
Originally Posted by nickhjort ↑
Hold on just a couple more days and I'll have that module installed. I just haven't had time to rip the dash again. I also have to rethink my clutch switch, the switch broke. That's what I get for going cheap :) Anyway, I'll prolly just buy the oem one. I'll put picks up when I'm done with all of this...

but I understand an 09 has no need to rip apart the das?
CTScottUSA, CT · Jun 6, 2009#326
Originally Posted by PhilD424 ↑
The cost of that kit is exactly why we looked for a cheaper route. Looking at the installation instructions for it, it actually does the cruise control itself, as opposed to using the Yaris's built in functionality.
lunjiaowPerth, Australia. · Jun 6, 2009#327
Well i pulled apart my dash on the 07 Australian Delivered Yaris, to find there is no CCS blue wire from the ECM to the AD4 Plug. Unless i got it wrong but there was a blue wire on the bottom row which i doubt was the CCS wire.. Very disappointing.
PatrickJohnsonMurfreesboro, TN · Jun 7, 2009#328
Originally Posted by lunjiaow ↑
Well i pulled apart my dash on the 07 Australian Delivered Yaris, to find there is no CCS blue wire from the ECM to the AD4 Plug. Unless i got it wrong but there was a blue wire on the bottom row which i doubt was the CCS wire.. Very disappointing.
You can run one very easily. It took me literally 20 minutes to install this from popping the hood all the way through to drive testing. And i had to run a wire.
lunjiaowPerth, Australia. · Jun 7, 2009#329
Ah yes. i saw on Page 16... will give it a shot tomorrow.
pennyracergrants pass · Jun 10, 2009#330
i have read most of this thread looks cool and cheap for cruise control . so on my early 08 lb automatic i can use the oem stock and what else do i need ? please help i put ton of miles on my car and cruise would be way nice to have for cheap
mrbondThread starterIllinois · Jun 10, 2009#331
^ you need wires going from the ECM to the little hub in the steering wheel column, a wire going from that hub to a ground point, and the stalk, and then a jumper wire for two pins in the engine bay. Everything's been outlined and explained, so you just need to read carefully. That's about it. I'm selling my stalk btw, since I just don't really want it.
pennyracergrants pass · Jun 10, 2009#332
cool thanks for the input
petyancaCA · Jun 11, 2009#333
I have 09 3 door liftback, and it seems all I need is a stalk. Could someone give me a link to where you got the stalk ? Thanks a lot for the investigating this !
regalPA · Jun 11, 2009#334
Originally Posted by petyanca ↑
I have 09 3 door liftback, and it seems all I need is a stalk. Could someone give me a link to where you got the stalk ? Thanks a lot for the investigating this !

If you have a clutch you need the clutch switch, the part number is in this thread
CTScottUSA, CT · Jun 11, 2009#335
Originally Posted by petyanca ↑
I have 09 3 door liftback, and it seems all I need is a stalk. Could someone give me a link to where you got the stalk ? Thanks a lot for the investigating this !
Either ebay ($12.99 + $17 shipping):
http://cgi.ebay.com/ebaymotors/TOYOT...lenotsupported

or TRDSparks.com ($81.99 plus shipping):
part number: 84632-34011
menzEgypt · Jun 18, 2009#336
i am going to try this soon as i get bk home next month i have 07 yaris i just hope ull all b here to ask for my questions
CTScottUSA, CT · Jun 18, 2009#337
Originally Posted by menz ↑
i am going to try this soon as i get bk home next month i have 07 yaris i just hope ull all b here to ask for my questions
I don't think it will work on your car. On European manufactured Yaris cruise control is not an OEM option, so the ECM doesn't support this mod.
Prisonguardfind me · Jun 20, 2009#338
Ok, after reading all these posts I am now REALLY confused so please bear with me since I am also new here. I have an '09 S 5 door liftback, auto trans. In real simple terms since I am not an electrical engineer, what do I have to do to have the factory cruise installed. The dealer wants over $500 for an aftermarket one which is ridiculous.
CTScottUSA, CT · Jun 20, 2009#339
Originally Posted by Prisonguard ↑
Ok, after reading all these posts I am now REALLY confused so please bear with me since I am also new here. I have an '09 S 5 door liftback, auto trans. In real simple terms since I am not an electrical engineer, what do I have to do to have the factory cruise installed. The dealer wants over $500 for an aftermarket one which is ridiculous.
With an 09, you can simply purchase the OEM cruise control stalk (Toyota part number: 84632-3401), pull the steering wheel and install it, and you'll have cruise control.

Or, check out this thread for adding cruise to your 09 auto for about $10:

DIY - 2009 Cruise Control for $10, without pulling the steering wheel and airbag
Henry G.So Cal. · Jun 22, 2009#340
Just to confirm after reading 24 pages.....this will work on an '08 MT but you need the stalk, the clutch switch and need to do some wiring to the fuse box, correct?
CTScottUSA, CT · Jun 22, 2009#341
Originally Posted by Henry G. ↑
Just to confirm after reading 24 pages.....this will work on an '08 MT but you need the stalk, the clutch switch and need to do some wiring to the fuse box, correct?
Correct. We really need to do a DIY for 07-08's...
Henry G.So Cal. · Jun 22, 2009#342
That would be AWESOME. Thanks for all the info so far guys, great job.
POORSHANE CT · Jun 22, 2009#343
I have a 08 mt lb and a stock, lets do it.
CTScottUSA, CT · Jun 22, 2009#344
Originally Posted by POORSHA ↑
I have a 08 mt lb and a stock, lets do it.
For your MT you're going to need the clutch switch as well. It's OK to bypass it for testing, but for normal use you really should have it in place.

Anyone else from the New England region interested in doing theirs? We could do a DIY cruise control workshop.
nickhjortOneida, NY · Jun 23, 2009#345
I may move the led I have mounted next to the switches up into the guage cluster before I install the LED module CTScott has provided. Make it look a little more stock-ish. Also scott, if my LED is too bright I can just add a resistor of my choice in series and that'll dim it down some correct? And also I'm going to just buy the stock clutch switch for 20$ from the dealer, rather than try to fix the frankenstein I put together :)
CTScottUSA, CT · Jun 23, 2009#346
Originally Posted by nickhjort ↑
I may move the led I have mounted next to the switches up into the guage cluster before I install the LED module CTScott has provided. Make it look a little more stock-ish. Also scott, if my LED is too bright I can just add a resistor of my choice in series and that'll dim it down some correct? And also I'm going to just buy the stock clutch switch for 20$ from the dealer, rather than try to fix the frankenstein I put together :)
Yes, you can add a resistor to dim it. If you used a blue LED, you might have to go up to between 30K and 50K Ohms for it to not be blinding.
POORSHANE CT · Jun 23, 2009#347
A workshop would be great.
BravejusPlattsburgh, NY · Jun 23, 2009#348
I would like a workshop as well, or a well written DIY on the whole process with lots of pictures. The information on how to do this is rather scattered over 24 pages, especially if you have an 07-08 5mt.
CTScottUSA, CT · Jun 23, 2009#349
Originally Posted by Bravejus ↑
I would like a workshop as well, or a well written DIY on the whole process with lots of pictures. The information on how to do this is rather scattered over 24 pages, especially if you have an 07-08 5mt.
Well, we're up to two for the workshop. Would you be willing to drive down to Connecticut for it?
nickhjortOneida, NY · Jun 24, 2009#350
I am also willing to help out if people want to drive to Oneida, NY. I see that Bravejus is just up in Plattsburgh.