Yarisworld Archive

Can we do this? (aka The DIY Cruise Control Thread)

498 posts · 380,332 views · page 2 of 10

Replies continued

MGarganoNJ · Apr 14, 2009#51
Originally Posted by PK198105 ↑
the 5 speed uses the clutch switch and brake switch while the auto uses the gear position sensor and brake switch.
Does this mean, if all goes according to plan, that I'll need something other than the eBay stalk to make this work? This is assuming, of course, that the eBay stalk does what we all hope it will.
MGarganoNJ · Apr 14, 2009#52
ok thanks. Fingers crossed that this goes as planned!
AlexNet0Rockland, ME · Apr 14, 2009#53
Originally Posted by PK198105 ↑
cant help you there i have no clue how your remote starter is connected sorry🤷
I was just thinking out loud. I basically removed the clutch switch and the starter is permanantly enabled, not just when the clutch pedal is pressed. When i do this, if it works, I will have to install another switch.
enobmort42Denver, CO · Apr 15, 2009#54
...because i hate waiting for shipping, i stopped into the dealer to see the cost on this. $125 for the stalk, and if needed, either $44 or $16 for the jumper. then again, this isn't a tacoma; do we need it?

and the moral of the story: wait for the shipping! 🎉
IllusionXBrossard, QC · Apr 16, 2009#55
lol i'd love to know... you should've paid extra for express shipping ^_^
AlexNet0Rockland, ME · Apr 16, 2009#56
mine was just shipped as well
mrbondThread starterIllinois · Apr 16, 2009#57
Yup, just got my notice as well. lol apparently Thailand is 4 days ahead of us? jk
MGarganoNJ · Apr 16, 2009#58
Mine just shipped as well
goku87AK · Apr 16, 2009#59
Man, I really want to know if this will work. I'm all excited.
tk-421Dagobah · Apr 16, 2009#60
Originally Posted by goku87 ↑
Man, I really want to know if this will work. I'm all excited.
+1

This could be the ultimate cheap mod for the Yaris. Quite interested in the developments. 👍
enobmort42Denver, CO · Apr 16, 2009#61
^ def!
IllusionXBrossard, QC · Apr 16, 2009#62
<---- can't wait to know the answer

and guess what, MicroImage will stock this item? XD
marcustoronto, canada · Apr 16, 2009#63
wow if this works then this will save you $400 atleast..coz thats what toyota canada cahrges for cruise control..4-$450 canadian installation included ofcourse.
IllusionXBrossard, QC · Apr 16, 2009#64
Originally Posted by marcus ↑
wow if this works then this will save you $400 atleast..coz thats what toyota canada cahrges for cruise control..4-$450 canadian installation included ofcourse.
but that's not the OEM cruise.
ShroomsterOrlando · Apr 16, 2009#65
meh...we got the cruise for free when they were writing the paper work and the stalk is on the left side of the steering column
The SpectacleTampa, FL · Apr 16, 2009#66
interesting...
mrbondThread starterIllinois · Apr 16, 2009#67
^ I believe that's the aftermarket one he's talking about? Idk though
devinlamotheSudbury, Canada · Apr 16, 2009#68
Anyone have trouble getting the steering wheel bolts off (the hex screws on the side)? I was going to try and just check the mounting spot today but couldn't even get the screws to budge.

I'm thinking I need a torque wrench?
IllusionXBrossard, QC · Apr 17, 2009#69
Originally Posted by Shroomster ↑
meh...we got the cruise for free when they were writing the paper work and the stalk is on the left side of the steering column
Originally Posted by PK198105 ↑
you sure? i never saw the OEM one installed. the one we got is listed as a direct replacement for the OEM.🤷
You see, that's exactly what i'm talking about. Shroommaster got the aftermarket cruise control, which is exactly NOT what i wanted.

that was my main worry so i did not get the cruise option when i bought my yaris aero. I remembered, at the time, the sedan with package C came with factory cruise control.
ShroomsterOrlando · Apr 17, 2009#70
Originally Posted by PK198105 ↑
thats weird in the manual its on the right side🤷
yeah I thought so too...I'm pretty sure it's aftermarket as the switch itself doesn't toggle, it has three buttons....also there is no IPC light just a very bright annoying (at night) green light on the stalk to let you know it's on and ready to use.

the damn thing isn't visible through the holes in the steering wheel either, and it's backwards from what I'm used to....

top button is for decrease/set

side button is for on/off

bottom button is accel/cancel...weird huh....
CastawayQuebec city · Apr 17, 2009#71
Sounds like it's installed upside down...🤷
ShroomsterOrlando · Apr 17, 2009#72
Originally Posted by Castaway ↑
Sounds like it's installed upside down...🤷
I dunno...words read fine....lol
IllusionXBrossard, QC · Apr 17, 2009#73
i'm pretty sure it's who does it first. lol

too bad i wasn't in the crowd who "ordered it first"
MadMaxSan Antonio, Texas! · Apr 17, 2009#74
Originally Posted by Shroomster ↑
yeah I thought so too...I'm pretty sure it's aftermarket as the switch itself doesn't toggle, it has three buttons....also there is no IPC light just a very bright annoying (at night) green light on the stalk to let you know it's on and ready to use.

the damn thing isn't visible through the holes in the steering wheel either, and it's backwards from what I'm used to....

top button is for decrease/set

side button is for on/off

bottom button is accel/cancel...weird huh....
Actually, I thought I had factory cruise control but that sounds like what I have, which I now suspect is a Rostra Precision Controls Inc. aftermarket set-up...does it look like this?

Picture lost · news.hspn.com

Plus, if that is aftermarket, what does the factory set-up look like?

BTW, the Rostra has been discussed before...
ShroomsterOrlando · Apr 18, 2009#75
^^^that is the stalk that's installed


and this BELOW, is what an O.E.M toyota cruise stalk looks like...



Picture lost · img166.imageshack.us

courtesy of a toyotanation.com DIY
1NZYaris1New Zealand · Apr 18, 2009#76
So does this need to be run through the clock spring 🤷
if so does that mean we have to replace it as well.
just a thougt ,and probably a bad one.🤣
lunjiaowPerth, Australia. · Apr 18, 2009#77
you may need the wire to connect it to the clockspring.
Picture lost · foto.ixbt.com
Picture lost · foto.ixbt.com
top pictures are from the corolla... assuming it will be some what similar to the yaris.
i think the part number for that wire is 84633-42030
AlexNet0Rockland, ME · Apr 18, 2009#78
I think the pic of the one I Bought showed a wire with it. If not Ill just make one, no biggie.

The guy told me it shipped but no tracking #? is that because its USPS?
AlexNet0Rockland, ME · Apr 18, 2009#79
lol, okay. I usually deal with UPS and FedEx, I guess im spoiled that way.
lunjiaowPerth, Australia. · Apr 18, 2009#80
Originally Posted by Shroomster ↑
^^^that is the stalk that's installed


and this BELOW, is what an O.E.M toyota cruise stalk looks like...



Picture lost · img166.imageshack.us

courtesy of a toyotanation.com DIY
Well i just pulled my yaris airbag/horn out... and turns out to be like the picture above.
AlexNet0Rockland, ME · Apr 18, 2009#81
The thought crossed my mind as well
Klink10910 · Apr 18, 2009#82
Originally Posted by PK198105 ↑
how hard is it tho pull off the cover? i a bit scared of taking it off since i dont want my airbag to blow up in my face
Pulling the cover was a piece of cake. Changed out my steering wheel to a Scion and the install took me 20 minutes. To disable the airbag, I disconnected the battery the night prior. Check here on the forum, I can't for the life of me remember who did this first but they did a good write up on how to. It really pointed out battery disconnect and prying the wires for complete airbag removal.
lunjiaowPerth, Australia. · Apr 18, 2009#83
Yeah. its just two T30 torx bits on each side of the steering wheel. then just pull the horn/airbag off, be careful not to deploy the airbag and dont disconnet the airbag when battery is still connected. Its recommended to disconnect the battery and wait 60seconds or so to discharge power. I just wanted to check whats behind the steering wheel so i didn't disconnect the battery. Took less then 5mins to take out.
IllusionXBrossard, QC · Apr 18, 2009#84
my dealer had remove the top cover of my dashboard, and they did remove the passenger air bag without disconnecting the battery.
ozmddDFW, TX · Apr 18, 2009#85
Airbag pullers: its very easy. Make sure the battery is disconnected for a few minutes (I think the manual says 3-6, I waited 10), then use the CORRECT torx driver to remove the 2 side-bolts (you'll need one with a bit of reach), and it might take a decent tug to break the bolt initially, but then its easy). You should matchmark your wheel before you pull it. You shouldn't need a wheel pullet, just tug back-and-forth till it comes off. If you move your closckspring at all, read the directions on how to reset it. Its not hard, but needs to be done right or it will be an EXPENSIVE repair, and might set-off the airbag when you are turning. This is not a process to be afraid of, just take your time and know the steps. BTW - the "clockspring" is the name for the circular plastic unit behind the steerign wheel that allows all the wires to reach the steering wheel/cruise/airbag/horns and still spin the steering wheel round-and-round, where some very old vehicles ran the wires through a hollow center shaft.
devinlamotheSudbury, Canada · Apr 18, 2009#86
Originally Posted by ozmdd ↑
Airbag pullers: its very easy. Make sure the battery is disconnected for a few minutes (I think the manual says 3-6, I waited 10), then use the CORRECT torx driver to remove the 2 side-bolts (you'll need one with a bit of reach), and it might take a decent tug to break the bolt initially, but then its easy). You should matchmark your wheel before you pull it. You shouldn't need a wheel pullet, just tug back-and-forth till it comes off. If you move your closckspring at all, read the directions on how to reset it. Its not hard, but needs to be done right or it will be an EXPENSIVE repair, and might set-off the airbag when you are turning. This is not a process to be afraid of, just take your time and know the steps. BTW - the "clockspring" is the name for the circular plastic unit behind the steerign wheel that allows all the wires to reach the steering wheel/cruise/airbag/horns and still spin the steering wheel round-and-round, where some very old vehicles ran the wires through a hollow center shaft.
The problem I am having are the torx screws on the side ... they seem really hard to get off lol. But then again I was using a regular screw driver ... would a torque wrench do it? Or should I be using more force?
enobmort42Denver, CO · Apr 18, 2009#87
I was just reading this DIY a little while ago. I'm a huge fan of picture step-by-steps lol.
ShroomsterOrlando · Apr 18, 2009#88
Originally Posted by devinlamothe ↑
The problem I am having are the torx screws on the side ... they seem really hard to get off lol. But then again I was using a regular screw driver ... would a torque wrench do it? Or should I be using more force?



no...the TORX refers to the head/socket....
Picture lost · www.fakeplasticrock.com courtesy of fakeplasticrock.com
devinlamotheSudbury, Canada · Apr 19, 2009#89
Originally Posted by Shroomster ↑
no...the TORX refers to the head/socket....
Picture lost · www.fakeplasticrock.com courtesy of fakeplasticrock.com
No I know what torx are. I was just saying if a torque wrench using a torx head would do the trick.

I managed to get it though, the bit I was using was really crappy, so I ended up buying a new one and it worked.

[Edit]: Never mind, the wire that is connecting to the clockspring is the ground for the airbag and is replaced with the OEM wiring connection to/from the cruise stalk. Whew. Hopefully we get ours in the mail soon!
IllusionXBrossard, QC · Apr 20, 2009#91
the chances someone drumming on this steering wheel, the air bag deploying while someone is filming is VERY slim...
ShroomsterOrlando · Apr 20, 2009#92
the tags for the video as well as the other videos recommended lead me to believe it's from a car insurance company....
CTScottUSA, CT · Apr 20, 2009#93
Originally Posted by PK198105 ↑
guys , easy wait for CTScott to confirm if this is doable. From what i saw in the wiring it seems it will work , but i don't want you guys to spend money if you need an extra control module for it to work
Sorry for the delay in looking into this, but I was away on vacation. I looked this morning and agree that it should work with simply adding the switch.

Here is a quote from the 09 service manual:
"The microcomputer which controls the cruise control system is built into the ECM, and uses the throttle position sensor and motor as the actuator."

The stalk basically just has 4 switches and 3 resistors. The quick and dirty test (without removing the airbag) would be to short the ECM CCS pin to ground. If the cruise light illuminates on the combination meter, you are good to go.

CTScottUSA, CT · Apr 20, 2009#94
Originally Posted by PK198105 ↑
i think we need to be rolling above 25mph for the cruise to enable , its one of the failsafe conditions.
25mph is the minimum limit for "set", but the manual doesn't list a speed limit for the on/off function.
Sir A.Y. AtoyotSurrey, BC Canada · Apr 20, 2009#95
I just checked - my car ('08 5-door) doesn't have the wiring from the spiral cable to the ECM - nothing coming from that plug except the thin black horn wire. If the wiring for cruise were present, there would be two more wires.

So, installing cruise is probably still possible, but unfortunately it's not just a matter of adding a switch.
ka0sxCA east bay · Apr 20, 2009#96
guys, those of you who are saying few minutes, be careful, some car systems can take over an hour to discharge the sustaining capacitors, also ground yourself to prevent static discharge.
CTScottUSA, CT · Apr 20, 2009#97
Originally Posted by Sir A.Y. Atoyot ↑
I just checked - my car ('08 5-door) doesn't have the wiring from the spiral cable to the ECM - nothing coming from that plug except the thin black horn wire. If the wiring for cruise were present, there would be two more wires.

So, installing cruise is probably still possible, but unfortunately it's not just a matter of adding a switch.

My '09 has a blue wire in pin 1 and a brown in pin 3.

When I look at the models that the stalk part number is applicable to I see 06-09 sedans, but only 09 liftbacks.
CTScottUSA, CT · Apr 20, 2009#98
Originally Posted by PK198105 ↑
thats not where you connect the stalk to and the wire for css is already there,
wire 1 and 3 from the stalk is connected to 3 and 4 on the spiral cable
The stalk connects to the spiral cable on the steering wheel hub end, but the connector he pictured is the output of the spiral cable, heading towards the ECM. In his picture, the CCS wire (blue on my 09) is missing.
Sir A.Y. AtoyotSurrey, BC Canada · Apr 20, 2009#99
Originally Posted by PK198105 ↑
do you have that wire? the way i was looking at the ewd it seemed like these are used only as test points. either way it shouldn't be hard to just use the jumeper to connect the D3 with A21 i need to pop my cover to see better
I've done some research with the documentation that members have provided, and I can assure you that you need two wires coming out of that plug, in addition to the horn wire. One of them is blue and goes to the ECU. The other is a yellow ground wire.
Sir A.Y. AtoyotSurrey, BC Canada · Apr 20, 2009#100
Originally Posted by PK198105 ↑
....Anyways we shall see....
You said it.